GiroDisc brake rotor with curved grooves, representative image for A1-447
A2-172 Girodisc Chevrolet Camaro Z/28 (5th Gen) Rear Iron Rotor Conversion $2,182.00
Girodisc Chevrolet Camaro Z/28 (5th Gen) Rear Iron Rotor Conversion Upgrade your 5th-Gen Camaro Z/28 with Girodisc’s rear iron rotor conversion, engineered as a direct replacement for the OEM carbon-ceramic rotors. This high-performance setup delivers superior heat control, lower replacement costs, and the same confident braking feel that made the Z/28 a track legend. Direct Carbon-Ceramic Replacement, Built to Perform The Girodisc system is a true bolt-on solution—no modifications or adapters needed. Each rotor features a CNC-machined 6061-T6 aluminum hat mated to Girodisc’s proprietary cast-iron friction rings, both made in the USA. The floating two-piece design manages heat expansion under hard braking, maintaining perfect pad contact and preventing warping. Curved internal vanes act like centrifugal pumps to pull cooling air through the discs, keeping temperatures in check lap after lap. Features • Direct replacement for OEM carbon-ceramic rear rotors• Billet 6061-T6 aluminum hats with hard-anodized finish• Proprietary cast-iron rings poured and machined in the USA• Floating mount system with cadmium-plated steel drive pins• Anti-noise spring washers eliminate rattle while allowing float• Curved vane design improves airflow and cooling• Fully rebuildable—replace only the rotor rings when worn• Sold/priced per pair Vehicle Fitment Chevrolet Camaro Z/28 (2014–2015, 5th Generation)Fits OEM carbon-ceramic brake systems with factory Brembo calipers. Girodisc A2-172 Rear Rotor FAQs: Why switch from carbon-ceramic to iron rotors? Iron rotors offer greater heat capacity, improved modulation, and dramatically reduced replacement cost—ideal for track-day or endurance use where carbon ceramics can degrade quickly. Are these a direct fit for the Z/28’s carbon-ceramic setup? Yes. They bolt directly to the factory hubs and work with the original Brembo calipers and parking-brake system. Do these affect ABS or stability control? No. Girodisc rotors maintain factory geometry and tone-ring compatibility, so all electronic systems function normally. What difference will I feel when driving? Expect smoother pedal feedback, improved heat management under repeated hard braking, and more consistent stopping power throughout a session. Upgrade your Camaro Z/28 with Girodisc’s rear iron rotor conversion and experience the durability, balance, and braking precision trusted by serious track drivers everywhere.
GiroDisc brake rotor with curved grooves, representative image for A1-447
A1-172 Girodisc 2pc Front Brake Rotors for Chevy Camaro Z/28 (Gen 5) $2,182.00
Chevrolet Camaro Z/28 (5th Gen) Front Iron Rotor Conversion The Girodisc Front Iron Rotor Conversion for the fifth-generation Chevrolet Camaro Z/28 provides a lightweight, high-performance alternative to the factory carbon-ceramic rotors. Designed as a direct replacement for the OE discs, this system bolts on with no permanent modifications required. For optimal performance and reasonable rotor weight, it requires brake pads with a swept area (annulus) of 66mm or less, using the FMSI #1405 pad shape. Performance and Design By switching from carbon-ceramic to iron rotors, drivers benefit from improved heat management, reduced replacement costs, and consistent braking performance under repeated heavy use. The Girodisc design maintains factory brake bias and ABS functionality while significantly improving serviceability. Features - Direct replacement for the OEM front carbon-ceramic rotors. - Requires the FMSI #1405 pad shape (available in multiple compounds). - Two-piece floating rotor assembly combines a proprietary cast iron friction ring with a precision-machined 6061-T6 aluminum hat. - Curved internal vanes act as a centrifugal pump to maximize cooling airflow through the rotor. - Floating mount system with 12 high-strength alloy steel drive pins allows axial and radial float to accommodate heat expansion and reduce stress. - Anti-noise spring washers eliminate the rattle typically associated with floating rotors during street use. - Cadmium-plated hardware ensures long-term corrosion resistance and durability. - Lightweight two-piece design lowers rotational and unsprung mass, improving acceleration, steering response, and suspension control. Specifications Rotor Type: Two-piece floatingMaterial: Proprietary cast iron with 6061-T6 aluminum hatPad Requirement: FMSI #1405 (66mm swept area or less)Mount Hardware: 12 high-strength alloy steel drive pins, class 12.9 cap screwsOrigin: Designed, cast, and machined in the USAFitment: Chevrolet Camaro Z/28 (5th Gen) FAQs: Chevrolet Camaro Z/28 (5th Gen) Front Iron Rotor Conversion Why do I need to use a different pad shape? The Girodisc rotors are optimized for a 66mm pad annulus to maintain ideal weight and thermal characteristics. The required pad shape is FMSI #1405. Can I reuse my OEM pads? No. The OEM pads are too large for the reduced swept area and may cause overheating or excessive wear. Will this affect my ABS or brake balance? No. The system retains the factory brake bias and integrates seamlessly with the stock calipers and ABS tuning. Are these rotors noisy? The use of spring washers in the floating mount design minimizes rattle and vibration while still allowing full float under thermal load. What happens when the rotors wear out? The aluminum hats are reusable; you only need to replace the cast iron friction rings and reassemble with new hardware. Ordering Information Sold and priced per pair. Includes left and right front Girodisc rotors for the Chevrolet Camaro Z/28 (5th Gen). Requires FMSI #1405 brake pads for installation.
Girodisc replacement rotor rings
D2-145 Girodisc Corvette/Camaro 390mm Rear Replacement Rings $1,353.00
Girodisc Corvette, Camaro Rear Rings The Girodisc D2-145 rear replacement rings are designed for the 390mm Girodisc two-piece rotor systems used on Chevrolet Corvette C7 and Camaro SS/ZL1 models. These precision-engineered rings bolt directly to your existing Girodisc aluminum hats and include all new floating hardware, letting you replace only the wear surface for a cost-effective, high-performance brake refresh. Vehicle Fitment Compatible with:• Chevrolet Corvette C7 (including Grand Sport and Z06)• Chevrolet Camaro SS / ZL1 (6th Gen, 390mm Girodisc rear rotors)Note: For use only with Girodisc 390mm two-piece rear rotor systems. Not compatible with OEM or carbon-ceramic rotors. Features • Sold as a left/right pair with full hardware kit• Direct replacements for Girodisc 390mm two-piece rear rotors• CNC-machined from high-carbon cast iron for superior heat capacity• Curved directional vanes improve airflow and cooling• Maintains OEM brake balance and ABS function• Designed exclusively for Girodisc aluminum hats – not compatible with OEM or other brands Specifications • Diameter: 390mm• Position: Rear• Material: High-carbon cast iron• Mount type: Floating two-piece system• Includes: Two rings and new hardware kit• Sold/priced per pair Girodisc D2-145 Replacement Ring FAQs Will these fit factory Corvette or Camaro rotors? No. These are designed specifically for Girodisc two-piece rotor hats and are not compatible with factory or carbon-ceramic setups. Are both sides included? Yes. Each D2-145 kit includes both left and right replacement rings along with a complete hardware kit. Why replace just the rings instead of the full rotor? It allows you to maintain your Girodisc hats, lower cost, and restore braking performance without replacing the full assembly. Do I need to use the new hardware? Yes. The included new hardware must be used to ensure correct fitment and safety. Upgrade your Corvette or Camaro braking performance with Girodisc D2-145 390mm rear replacement rings — precision-built for strength, cooling, and fade-free stopping power on the street or the track.
Girodisc replacement rotor rings
Girodisc D1-145 Corvette/Camaro 394mm Front Replacement Rings $1,353.00
D1-145 Girodisc Corvette, Camaro 394mm Front Replacement Rings Bring race-level braking precision to your GM performance car with Girodisc D1-145 394mm front replacement rings. These high-performance rings bolt directly to your existing Girodisc aluminum hats using the included floating hardware kit. Each ring is CNC-machined from Girodisc’s proprietary high-carbon cast iron, ensuring excellent heat dissipation, consistent friction, and fade-free braking during aggressive street or track sessions. Vehicle Fitment Compatible with:• Chevrolet Corvette C7 Z06 / Grand Sport (Front)• Chevrolet Camaro ZL1 (6th Gen, 2017+)• Chevrolet Camaro SS 1LE (2016+)Note: Designed exclusively for Girodisc 394mm two-piece front rotor systems. Not compatible with OEM one-piece or carbon-ceramic rotors. Features • Sold as a left/right pair with full floating hardware kit• Direct replacements for Girodisc 394mm two-piece front rotors• CNC-machined from high-carbon iron alloy for superior heat resistance• Directional curved vanes accelerate airflow and reduce operating temperatures• Maintains factory brake bias, ABS, and stability control calibration• Precision-balanced for smooth operation and reduced unsprung weight• Designed exclusively for Girodisc aluminum hats Specifications • Diameter: 394 mm• Position: Front• Material: High-carbon cast iron• Mount type: Floating two-piece system• Includes: Two rotor rings and new hardware kit• Sold/priced per pair Girodisc D1-145 Corvette / Camaro 394mm Front Replacement Ring FAQs Do these rotors fit OEM Z06 or ZL1 hats? No. The D1-145 rings are specifically engineered for Girodisc aluminum hats and cannot be mounted to factory one-piece rotors or carbon-ceramic assemblies. What pad compounds work best with these rings? For dual-use driving, Pagid RS29 or Ferodo DS2500 pads are recommended. For dedicated track setups, use Pagid RSL1  compounds for higher temperature thresholds. What torque specs are required for the mounting hardware? Torque each fastener to 12 ft-lbs (16 Nm) using blue Loctite. Recheck torque after the first full heat cycle to confirm proper seating. Are these rotors directional? Yes. Each ring is labeled for left and right installation — follow the vane direction to maintain optimal airflow and cooling under heavy braking. Upgrade your Corvette or Camaro’s braking system with Girodisc D1-145 394mm front replacement rings — engineered for endurance, balance, and peak thermal performance on road or circuit.
Pagid 8091 Brake Pad Technical drawing of a brake pad with dimensions labeled
Pagid Racing Brake Pads 8091 from $1,208.00
Pagid Racing Brake Pad Shape 8091 Fitment Guide for Pagid 8091 Brake Pad Make Model Build (Year) Front Rear Chevrolet Camaro Z28 [Gen 5] [ceramic brakes] 2015 - 17 X Chevrolet Corvette C6 Brembo [ceramic brakes] 2009 - 13 X Chevrolet Corvette C6 Brembo [6-piston iron rotors] 2009 - 13 X Chevrolet Corvette C7 Z06 [ceramic brakes] 2015 + X Ferrari 430 Challenge [ceramic brakes] X Ferrari 430 Scuderia [ceramic brakes] 2007 - 10 X Ferrari 458 Italia [ceramic brakes] 2010 - 15 X Ferrari 488 Challenge race car [ceramic brakes] 2016 + X Ferrari 599 GTB Fiorano [iron rotors] 2006 - 12 X Ferrari Several ceramic (CCM) brakes X McLaren 570S [ceramic brakes] 2015 + X McLaren 650S / Spyder [ceramic brakes] 2014 - 17 X McLaren 675LT [ceramic brakes] 2015 + X McLaren MP4-12C [ceramic brakes] 2011 - 14 X Fits the Following Calipers: Make Type Remarks Shape No. Brembo XA5.71.xx 6-piston D85 16mm 8091   Pagid Racing Brake Pads are engineered for high-performance driving, delivering exceptional stopping power, durability, and control under the most demanding conditions. Trusted by professional racers and performance enthusiasts worldwide, these pads are crafted using advanced friction materials and cutting-edge technology to ensure consistent performance, low fade, and excellent modulation. Whether you're on the track or tackling aggressive street driving, Pagid Racing Brake Pads provide the reliability and confidence you need to push your vehicle to its limits. Pagid Racing Brake compounds are for steel (cast iron) rotors only unless otherwise noted. Pagid RSL 1 Compound Used in GT cars, touring cars and prototype endurance racing. Due to the high friction and good modulation, often used in sprint races as well. RSL 1 is a low metallic resin bonded material containing steel and aramid fibers with very high heat resistance. It maintains a constant friction level over a wide range of temperatures. Its reduced wear rate and disc friendliness make this material appropriate for endurance races. In the 8091 pad shape, the RSL 1 comes in an RSL 1 Special compound, both specified for Brembo and Ford Multimatic applications. Pagid RSL 19 Compound Pagid RSL 19 is a low metallic resin bonded material containing steel and aramid fibers. It maintains a constant friction level across a broad range of temperatures. The material features very good modulation and release characteristics. Rear axle usage in combination with RSL 1 or RSL 2 on the front axle in heavier cars (GT3/GTE). Front axle usage for lighter GT and touring cars. Pagid RSC 1 Compound (Ceramic Rotors Only) A race and track day compound for all known types of ceramic brake discs, RSC 1 is a low metallic resin bonded material containing steel and aramid fibers. This material features good all-round characteristics and is suitable for all types of usage. Pagid RSC 2 Compound (Ceramic Rotors Only) Pagid RSC 2 is a special race compound for ceramic discs with a high content of fibers in the friction surface for sprint and endurance circuit racing. RSC 2 is a low metallic resin bonded material containing steel and aramid fibers. This material is specifically developed for above mentioned applications. Pagid RSC 3 Compound (Ceramic Rotors Only) RSC 3 is a low metallic resin bonded material containing steel fibers. This material is specifically developed for above mentioned applications. It is a special race compound for ceramic discs with low content of fibers in the friction surface for sprint and endurance circuit racing.
Pagid 8091 Brake Pad Technical drawing of a brake pad with dimensions labeled
Performance Friction 1395 Racing Brake Pads $1,110.00
Performance Friction PFC 1395 Racing Brake Pads Performance Friction PFC 1395 Racing Brake Pad Fitment Guide Make Model Build (Year) Front Rear Chevrolet Camaro Z28 [Gen 5] [ceramic brakes] 2015 - 17 X Chevrolet Corvette C6 Brembo [ceramic brakes] 2009 - 13 X Chevrolet Corvette C6 Brembo [6-piston iron rotors] 2009 - 13 X Chevrolet Corvette C7 Z06 [ceramic brakes] 2015 + X Ferrari 430 Challenge [ceramic brakes] 2007-09 X Ferrari 430 Scuderia [ceramic brakes] 2008 - 09 X Ferrari 458 Italia [ceramic brakes] 2010 - 15 X Ferrari 488 Challenge race car [ceramic brakes] 2016 - 23 X Ferrari 599 GTB Fiorano [iron rotors] 2006 - 12 X Ferrari Several ceramic (CCM) brakes X McLaren 570S [ceramic brakes] 2015 + X McLaren 650S / Spyder [ceramic brakes] 2014 - 17 X McLaren 675LT [ceramic brakes] 2015 + X McLaren MP4-12C [ceramic brakes] 2011 - 14 X Fits the Following Calipers: Make Type Remarks Shape No. Brembo XA5.71.xx 6-piston D85 16mm 8091   The Performance Friction PFC 1395 racing brake pad is designed for compatible high-performance brake calipers used in demanding track and motorsport applications. Measuring 189.6 mm wide by 97 mm high, with an 85 mm friction material depth and 17 mm overall thickness, the PFC 1395 features a wide friction surface, distinctive retaining geometry, and two friction grooves. Available at Competition Motorsport in PFC 11 and PFC 331 racing compounds, the 1395 pad shape gives drivers two different approaches to braking performance. Whether you prefer the smooth, progressive characteristics of Compound 11 or the ABS-friendly, high-initial-bite characteristics of Compound 331, selecting the right friction material is essential for consistent braking and driver confidence. Performance Friction PFC 1395 Brake Pad Specifications Manufacturer: Performance Friction (PFC) Pad Shape: 1395 Overall Width: 189.6 mm Overall Height: 97 mm Friction Material Depth: 85 mm Pad Thickness: 17 mm Available Compounds: PFC 11 and PFC 331 Applications: Compatible motorsport brake calipers requiring the 1395 pad shape PFC 11 Racing Compound – Smooth Bite and Progressive Braking Performance Friction Compound 11 is a racing friction material developed for sprint and medium-distance competition. Known for its smooth initial bite and increasing friction characteristics as temperature rises, PFC 11 provides a progressive braking response for drivers who prioritize predictable pedal feel and precise modulation. Compound 11 is well suited to competitive road racing, advanced HPDE, and demanding track applications where repeatable braking response is essential. PFC 331 Racing Compound – High Initial Bite and ABS Compatibility Performance Friction Compound 331 is a degressive racing brake compound developed primarily for front-axle applications. It combines strong initial bite with controlled friction characteristics, making it particularly attractive for racing vehicles equipped with sophisticated ABS systems. Its degressive friction behavior is designed to support braking stability and control while offering favorable pad and rotor wear characteristics. PFC 331 is an excellent option for compatible front brake systems where ABS interaction and predictable high-performance braking are priorities. PFC 11 vs. PFC 331 – Which Compound Should You Choose? PFC 11: Smooth initial bite with friction that increases as temperature rises. Designed for sprint and medium-distance racing applications. PFC 331: Strong initial bite with degressive friction behavior. Developed for front-axle racing applications, with an emphasis on ABS compatibility and low wear. The ideal compound depends on vehicle weight, tire grip, brake balance, ABS calibration, rotor configuration, operating temperatures, and driving style. Contact Competition Motorsport for help selecting the correct PFC friction material. Why Choose Performance Friction PFC 1395 Brake Pads? Competition-focused Performance Friction braking technology 189.6 mm wide backing plate with distinctive retaining geometry 85 mm friction material depth 17 mm overall pad thickness Available in PFC 11 and PFC 331 racing compounds PFC 1395 Brake Pad Fitment and Compatibility The Performance Friction 1395 pad shape is intended for compatible brake calipers requiring its specific backing plate geometry, retaining-hole locations, friction surface dimensions, and overall thickness. Before ordering, verify the 189.6 mm width, 97 mm height, 85 mm friction material depth, and 17 mm thickness against your existing pads or the brake caliper manufacturer's technical specifications. Vehicle make and model alone may not confirm fitment, especially when aftermarket racing calipers or optional performance brake systems are installed. Buy PFC 1395 Racing Brake Pads at Competition Motorsport Competition Motorsport specializes in Performance Friction racing brake pads, high-performance braking components, and professional motorsport equipment for HPDE enthusiasts, club racers, and competitive race teams. Select your preferred PFC 1395 compound, 11 or 331, above. If you need assistance confirming pad shape compatibility or selecting the correct compound, contact our motorsports specialists before ordering.
girodisc hero image
Girodisc 1382.17 Front Brake Pads for Iron Rotor Conversion from $888.00
GiroDisc 1382 Front Racing Brake Pads for Iron Rotor Conversions  GiroDisc 1382.17 Front Brake Pad Fitment Guide  McLaren 750S with TrackPackMcLaren 765LT (standard brakes and Clubsport Pack)McLaren SennaMcLaren 675LTMcLaren 650SMcLaren 570S / 570GTMcLaren MP4-12C (oem ccb) Used with GiroDisc Iron Conversion only.  Do NOT use these pads with your OEM CCB Rotors. GiroDisc 1382.17 Front Brake Pad Compounds GP10 Street / Track-Day Compound Designed for spirited street use and mild track driving. Offers low dust, excellent cold bite, and smooth pedal feel with strong fade resistance. GP30 Endurance Race Compound Built for extended high-temperature operation. Ideal for endurance racing and heavy track use where consistency and rotor life are key. GP35 All-around track and race compound—balancing endurance-pad longevity with sprint-pad bite. It’s best suited to HPDE, frequent track days, and racing where modulation and wear life both matter.  GiroDisc 1382 Brake Pad Frequently Asked Questions (FAQ) Can I daily drive with GP10 pads? GP10 is the best compromise between street and track use.   Do I need GiroDisc rotors to use these pads? Yes, pairing these pads with GiroDisc two-piece rotors is recommended for the best results.
Pagid racing brakes pad shape no. 4906
Pagid 4906 Racing Brake Pads from $879.00
Pagid Racing Brake Pad Shape 4906 Pagid 4906 Brake Pad Fitment Guide Make Model Build (Year) Front Rear Chevrolet Camaro Z28 [Gen 5] [ceramic brakes] 15 - 17 X Chevrolet Corvette C6 Brembo [ceramic brakes] 09 - 13 X Chevrolet Corvette C7 Z06 [ceramic brakes] 15 - X Dodge Viper ACR [ceramic brakes] 14 - 17 X Ferrari 360 Challenge Stradale [ceramic brakes] 03 - 05 X Ferrari 430 Challenge [ceramic brakes] X Ferrari 430 Scuderia [ceramic brakes] 07 - 10 X Ferrari 458 Italia [ceramic brakes] 10 - 15 X Ferrari 488 Challenge race car [ceramic brakes] 16 - X Ferrari 599 GTB Fiorano 06 - 12 X Ferrari Enzo [ceramic brakes] 02 - 04 X Ferrari F430 [ceramic brakes] 05 - 10 X Ferrari Several ceramic brakes CCM X Lamborghini Aventador LP700-4 [ceramic brakes] 11 - X Lamborghini Several ceramic brakes X   Pagid Racing Brake Pads are engineered for high-performance driving, delivering exceptional stopping power, durability, and control under the most demanding conditions. Trusted by professional racers and performance enthusiasts worldwide, these pads are crafted using advanced friction materials and cutting-edge technology to ensure consistent performance, low fade, and excellent modulation. Whether you're on the track or tackling aggressive street driving, Pagid Racing Brake Pads provide the reliability and confidence you need to push your vehicle to its limits. These Pagid Racing Brake compounds are for ceramic rotors only. Pagid RSC 1 Compound (Ceramic Rotors Only) A race and track day compound for all known types of ceramic brake discs, RSC 1 is a low metallic resin bonded material containing steel and aramid fibers. This material features good all-round characteristics and is suitable for all types of usage. Pagid RSC 2 Compound (Ceramic Rotors Only) Pagid RSC 2 is a special race compound for ceramic discs with a high content of fibers in the friction surface for sprint and endurance circuit racing. RSC 2 is a low metallic resin bonded material containing steel and aramid fibers. This material is specifically developed for above mentioned applications.
Pagid 8091 Brake Pad Technical drawing of a brake pad with dimensions labeled
Ferodo FCP5030 Brake Pads from $790.00
Ferodo FCP5030 Porsche Brake Pads Ferodo FCP5030 Brake pad Fitment Guide (FMSI D1395) Make Model Build (Year) Front Rear Chevrolet Camaro Z28 [Gen 5] [ceramic brakes] 15 - 17 X Chevrolet Corvette C6 Brembo [ceramic brakes] 09 - 13 X Chevrolet Corvette C6 Brembo 6 piston non ceramic 09 - 13 X Chevrolet Corvette C7 Z06 [ceramic brakes] 15 - X Ferrari 430 Challenge [ceramic brakes] X Ferrari 430 Scuderia [ceramic brakes] 07 - 10 X Ferrari 458 Italia [ceramic brakes] 10 - 15 X Ferrari 488 Challenge race car [ceramic brakes] 16 - X Ferrari 599 GTB Fiorano 06 - 12 X Ferrari Several ceramic brakes CCM X McLaren 570S [ceramic brakes] 15 - X McLaren 650S / Spyder [ceramic brakes] 14 - 17 X McLaren 675LT [ceramic brakes] 15 - X McLaren MP4-12C [ceramic brakes] 11 - 14 X Ferodo DS3.12 Brake Compound Details The DS3.12 is the latest evolution in Ferodo's incredible DS line. Sports cars today have more of everything: more horsepower, more sophisticated aero, higher curb weights, and stickier tires. These attributes place serious demands on a vehicle's brake system. The Ferodo DS3.12 is the modern pad compound designed from the start to explicitly handle those demands. The Ferodo DS3.12 is a top-tier endurance racing brake pad compound built for maximum fade resistance, high friction, and extremely consistent performance at elevated temperatures. If you need a Ferodo track brake pad for aggressive braking, long sessions, and serious motorsport use, DS3.12 is one of the strongest options in the lineup. The DS3.12 compound provides strong initial bite, a highly stable torque curve, and dependable braking performance in demanding track conditions. It is ideal for experienced drivers, endurance racing, and high-grip applications where repeatable stopping power matters most. Maximum fade resistance in the Ferodo range High friction and strong initial bite Very consistent braking response at track temperatures Excellent durability in endurance racing use Best for: advanced track-day drivers and racers who want a high-performance race brake pad with elite heat capacity and confidence-inspiring consistency. Note: DS3.12 is a full race compound and may produce increased dust, disc wear, and reduced cold performance compared with street-oriented pads. Ferodo DS1.11 Brake Compound Details The DS1.11 has a lower mu than the DS3.12 at all temperatures and can be characterized as a moderate mu pad vs. other endurance racing compounds. They require more pedal force than the DS3.12, and they have a slightly declining torque curve as temperatures rise. As they get hotter and you dive deeper into a turn, you may feel like you need to push a little harder on the brake pedal to elicit the same response (which is a feel many drivers actually prefer). Some drivers feel that the DS1.11 is more controllable on street tires than DS3.12 since ABS cannot be activated as easily. It will last a fairly long time vs. many other pad compounds on the market but does not last quite as long as the DS3.12. They are very gentle on discs at track temperatures when a proper pad transfer layer is maintained. The DS1.11 also has an outstanding max temp and fade resistance, just not quite as high as 3.12. We're not aware of anyone who has faded them, and most people differentiate between the DS1.11 and DS3.12 based on feel. The Ferodo DS1.11 is a proven endurance racing brake pad compound designed for drivers who need outstanding fade resistance, long pad life, and precise control under repeated high-temperature braking. For track cars and serious HPDE builds, DS1.11 is a trusted Ferodo race brake pad with a strong reputation for consistency. This DS1.11 features stable braking performance, excellent modulation, and durability in demanding track conditions. Compared with more street-focused compounds, DS1.11 is better suited to aggressive lapping, endurance sessions, and drivers who value a progressive pedal feel. Exceptional fade resistance for track use Long wear characteristics in endurance-style driving Progressive, controllable pedal feel Excellent choice for HPDE and racing applications Best for: drivers looking for a track brake pad with durability, modulation, and high-temperature stability for repeated hard use. Note: DS1.11 is a race compound and is not ideal for customers seeking low noise, low dust, or refined street manners. Ferodo DS2500 Compound Details Although we always recommend using a dedicated race pad for the track, the DS2500 is one of the best hybrid street/track pads on the market. It features the moderately high bite and solid fade resistance of a track pad, with the relatively low dust and noise levels of a street pad. When used as a street pad, it can produce some squeal on certain vehicle platforms. If you drive aggressively on the street, do some canyon runs, autocross, and maybe some light track duty on street tires, the DS2500 is tough to beat. The Ferodo DS2500 is one of the most popular performance brake pad compounds for drivers who want strong braking on the street and dependable performance at the track. If you are looking for a street and track brake pad with excellent cold bite, low noise, and impressive fade resistance, the DS2500 is a proven choice. The DS2500 delivers confident pedal feel, consistent stopping power, and better high-temperature performance than typical street pads. It is an excellent option for spirited driving, autocross, HPDE, and dual-purpose performance cars. Strong cold bite for street use Low noise when properly bedded Excellent fade resistance for a dual-purpose pad Great match for performance street tires Best for: drivers who want a versatile Ferodo brake pad for daily driving, canyon runs, and light to moderate track use without giving up refinement. Note: DS2500 is a race-derived compound and may produce more dust than an ordinary OEM street pad. Ferodo FCP5030 Comparison Chart Out of all the pad compounds we've ever tested, from all manufacturers, the Ferodo DS3.12 shows the flattest torque curve across the broadest temperature range. That means on every turn, on every track you drive, on every lap, your brake pedal is going to feel almost exactly the same, providing tremendous consistency and repeatability. The DS3.12 has a higher mu (µ) than Ferodo's other compounds, so not as much pedal pressure is required to initiate the desired response. It is also un-fadable, showing no drop in performance at any temperature your brakes will ever see. Ferodo FCP5030 Coefficient of Friction (Mu) Comparison Chart In dyno testing, the Ferodo DS3.12 has shown superior wear rates to the other Ferodo compounds, while remaining kind to brake rotors. We believe the Ferodo DS3.12 will become the gold standard by which other race compounds will be judged. Ferodo FCP5030 Operating Temperature Comparison Chart **Designed for use with iron brake rotors only. Not for use with carbon-ceramic rotors.**
Pagid racing brakes pad shape no. 4906
GiroDisc 1001.15 Rear Brake Pads for Iron Rotor Conversion from $713.00
GiroDisc 1001.15 Rear Brake Pads for Iron Rotor Conversion GiroDisc 1001.15 Rear Brake Pad Fitment Guide  Lamborghini Aventador Used with GiroDisc Iron Conversion only.  Do NOT use these pads with your OEM CCB Rotors. GiroDisc 1001.15 Rear Brake Pad Compounds GP10 Street / Track-Day Compound Designed for spirited street use and mild track driving. Offers low dust, excellent cold bite, and smooth pedal feel with strong fade resistance. GP30 Endurance Race Compound Built for extended high-temperature operation. Ideal for endurance racing and heavy track use where consistency and rotor life are key. GP35 All-around track and race compound—balancing endurance-pad longevity with sprint-pad bite. It’s best suited to HPDE, frequent track days, and racing where modulation and wear life both matter.  GiroDisc 1001 Rear Brake Pad Frequently Asked Questions (FAQ) Can I daily drive with GP10 pads? GP10 is the best compromise between street and track use.   Do I need GiroDisc rotors to use these pads? Yes, pairing these pads with GiroDisc two-piece rotors is recommended for the best results.
Pagid 8091 Brake Pad Technical drawing of a brake pad with dimensions labeled
Carbotech CT1395 Brake Pads from $556.00
Carbotech CT1395 Brake Pads Carbotech CT1395 Brake Pad Fitment Guide Make Model Build (Year) Front Rear Chevrolet Camaro Z28 [Gen 5] [ceramic brakes] 15 - 17 X Chevrolet Corvette C6 Brembo [ceramic brakes] 09 - 13 X Chevrolet Corvette C6 Brembo 6 piston non ceramic 09 - 13 X Chevrolet Corvette C7 Z06 [ceramic brakes] 15 - X Ferrari 430 Challenge [ceramic brakes] X Ferrari 430 Scuderia [ceramic brakes] 07 - 10 X Ferrari 458 Italia [ceramic brakes] 10 - 15 X Ferrari 488 Challenge race car [ceramic brakes] 16 - X Ferrari 599 GTB Fiorano 06 - 12 X Ferrari Several ceramic brakes CCM X McLaren 570S [ceramic brakes] 15 - X McLaren 650S / Spyder [ceramic brakes] 14 - 17 X McLaren 675LT [ceramic brakes] 15 - X McLaren MP4-12C [ceramic brakes] 11 - 14 X Available Carbotech Compounds 1521 — High-performance street compound with low dust, low noise, and excellent release and modulation. AX6 — Autocross-focused compound with strong low-temperature bite and progressive control. XP8 — Entry racing and track-day compound with strong fade resistance and rotor-friendly behavior. XP10 — Higher-torque race compound with strong initial bite and excellent fade resistance. XP12 — More aggressive race compound with added bite and high-temperature capability. RP2 — Endurance racing compound designed for sustained performance and strong fade resistance. XP20 — Very aggressive racing compound with high torque and extreme heat capability. XP24 — Top-tier Carbotech race compound engineered for maximum torque and endurance-level demands. How to Choose the Right Compound 1521 is the street-focused option. AX6 is intended for autocross. XP8, XP10, XP12, XP20, and XP24 are race-oriented compounds with increasing heat and torque capability. RP2 is designed for endurance racing. Track and racing compounds are not intended for normal street use. Carbotech CT1395 Brake Pads FAQs How do I know if CT1395 fits my vehicle?Review the Vehicle Fitment section above and compare the make, model, year range, and notes such as caliper, rotor, or trim details to your vehicle. Which Carbotech compound is best for street driving?The 1521 compound is Carbotech's street-focused option. The other compounds in this listing are intended for autocross, track, or race applications. Do I need to bed in Carbotech brake pads?Yes. Proper bedding is important for pad transfer, performance, and wear. Follow Carbotech's recommended bedding procedure for the chosen compound. Choose the Carbotech CT1395 compound that matches your vehicle and driving demands, then confirm fitment carefully before checkout.
Pagid racing brakes pad shape no. 4906
Carbotech CT1165 Brake Pads from $434.00
Carbotech CT1165 Brake Pads Carbotech CT1165ZR Brake Pad Fitment Guide Make Model Build (Year) Front Rear Chevrolet Camaro Z28 [Gen 5] [ceramic brakes] 15 - 17 X Chevrolet Corvette C6 Brembo [ceramic brakes] 09 - 13 X Chevrolet Corvette C7 Z06 [ceramic brakes] 15 - X Dodge Viper ACR [ceramic brakes] 14 - 17 X Ferrari 360 Challenge Stradale [ceramic brakes] 03 - 05 X Ferrari 430 Challenge [ceramic brakes] X Ferrari 430 Scuderia [ceramic brakes] 07 - 10 X Ferrari 458 Italia [ceramic brakes] 10 - 15 X Ferrari 488 Challenge race car [ceramic brakes] 16 - X Ferrari 599 GTB Fiorano 06 - 12 X Ferrari Enzo [ceramic brakes] 02 - 04 X Ferrari F430 [ceramic brakes] 05 - 10 X Ferrari Several ceramic brakes CCM X Lamborghini Aventador LP700-4 [ceramic brakes] 11 - X Lamborghini Several ceramic brakes X Available Carbotech Compounds 1521 — High-performance street compound with low dust, low noise, and excellent release and modulation. AX6 — Autocross-focused compound with strong low-temperature bite and progressive control. XP8 — Entry racing and track-day compound with strong fade resistance and rotor-friendly behavior. XP10 — Higher-torque race compound with strong initial bite and excellent fade resistance. XP12 — More aggressive race compound with added bite and high-temperature capability. RP2 — Endurance racing compound designed for sustained performance and strong fade resistance. XP20 — Very aggressive racing compound with high torque and extreme heat capability. XP24 — Top-tier Carbotech race compound engineered for maximum torque and endurance-level demands. How to Choose the Right Compound 1521 is the street-focused option. AX6 is intended for autocross. XP8, XP10, XP12, XP20, and XP24 are race-oriented compounds with increasing heat and torque capability. RP2 is designed for endurance racing. Track and racing compounds are not intended for normal street use. Carbotech CT1165ZR Brake Pads FAQs How do I know if CT1165ZR fits my vehicle?Review the Vehicle Fitment section above and compare the make, model, year range, and notes such as caliper, rotor, or trim details to your vehicle. Which Carbotech compound is best for street driving?The 1521 compound is Carbotech's street-focused option. The other compounds in this listing are intended for autocross, track, or race applications. Do I need to bed in Carbotech brake pads?Yes. Proper bedding is important for pad transfer, performance, and wear. Follow Carbotech's recommended bedding procedure for the chosen compound. Choose the Carbotech CT1165ZR compound that matches your vehicle and driving demands, then confirm fitment carefully before checkout.
American Express Apple Pay Discover Google Pay Klarna Maestro Mastercard PayPal Shop Pay Visa