458 Challenge

CMS Performance RF1 DOT4 Racing Brake Fluid Real-Life High Boiling Point Without The Real High Price RF1 Racing Brake Fluid from CMS Performance is a fully-synthetic DOT4 brake fluid formulated to provide extraordinary performance under the most demanding high-temperature racing and track-day conditions. With a dry boiling point of 328º C (622º F), RF1 exceeds all DOT3 & DOT4 requirements and is compatible with all DOT 3, 4, and 5.1 fluids. (Not compatible with DOT5 or mineral-based brake fluids.) On the race track, brake systems operate at very high sustained temperatures, and there is perhaps no single safety system more important in racing than your brakes. No single part of that system is more critical than brake fluid. At CMS Performance, we got tired of (and a little nervous) using "racing" brake fluid at the race track that didn't live up to its claimed performance when things got hot. So we did something about it. Manufactured in partnership with Orthene, the brake fluid supplier to many teams in Formula 1, WEC, and other professional series, RF1 Racing Brake Fluid was formulated to maintain consistent viscosity, lubricity, and compressibility at the extreme system temperatures and line pressures found in racing and track days. The bottom line is this: you can spend more on brake fluid, but you can't buy higher-performance than RF1 Racing Brake Fluid. RF1 Racing Brake Fluid Details: Typical dry boiling point: 328º C (622º F) Typical wet boiling point: 204º C (399º F) Exceeds DOT3 & DOT4 standards Bottle size: 500 ml (16.9 fl oz) Click Here for Product MSDS Sheet A Word About Flushing Brake Fluid All brake fluid degrades over time (not mileage), attracting water as it ages, which, at high brake temperatures, can lead to fluid boil and brake fade or failure. That's why the "wet" (aged) boiling point of any brake fluid is substantially lower than the "dry" (new) boiling point. To maintain maximum braking performance, Competition Motorsport strongly suggests replacing your brake fluid before every track event, but at least every three months if you're consistently racing and/or driving at track days. It's cheap insurance against learning about brake fade the hard way!

Girodisc Brake Pad Spreader This indispensable tool is used by race teams, shops, and enthusiasts alike who have high performance four- and six-piston calipers. The Girodisc Brake Pad Spreader is designed to easily spread brake pads and pistons to facilitate quick replacement of pads and/or rotors in a shop or racing environment. No more screwdrivers, pliers, hammers, or C-clamps! This tool will retract the pistons fully and evenly into their bores with one squeeze of the levers. The Girodisc Brake Pad Spreader was designed to be used with popular racing brake calipers from Brembo, AP Racing, Alcon, and other performance calipers in racing and road use. To help it fit into any caliper, the amount of throw is adjustable. Insert the spreading plates one way for wider six-piston calipers, then turn the spreader 90o and use the plate sides for four-piston calipers. The Girodisc Brake Pad Spreader is made from heavy-gauge steel, powder-coated for durability. The slider is cadmium-plated, and nylon pivot bushings ensure smooth action. The Girodisc Brake Pad Spreader will quickly become an invaluable tool for any race team, shop, or enthusiast who changes pads and rotors frequently.

RS 14: Outside the track day environment, RS14 has shown success in short- to medium-distance circuit racing as well as gravel and tarmac rallying. RS14 offers very low heat conductivity, resulting in lower caliper and brake fluid temperatures. RS14 offers consistent levels of performance and much longer life than competitors' products without excessive rotor wear, offering the driver supreme confidence. The PAGID RS14 (Black) is a high-friction-value ceramic compound with very good modulation, high fade resistance, low heat conductivity, and a good wear rate up to a constant temperature of 1,200°F (650°C). It's kind on rotors, with visible grooving but no tendency to crack them. RS14 is our most popular ceramic-based friction material. It will tolerate much higher working disc temperatures than PAGID RS4-2, extending fade resistance. RS14 is used as an OEM material and supplied as an upgraded track day pad by Lotus Motorsport. It has been shown to exhibit optimum levels of braking force, control and modulation on popular track-day cars such as the Lotus Elise and Caterham 7.  RSL 29: Designed primarily for endurance racing, due to consistent levels of performance and user friendliness many competitors use this material for sprint and short distance races also. RS29 has also found favor in the growing track-day market due to the high level of control, good cold performance, long life, and low rotor wear. The PAGID RS29 (Yellow) is the world-leading endurance brake pad used by most of the winning teams in motorsport.  Based on the RS14, a slight reduction of the friction value improves modulation and longevity. The friction value remains high enough for cars without power-assisted brake systems, ensuring low effort on the brake pedal. Constant temperatures up to 1,100°F (600°C) are possible. This combination of friction value, fading stability, and low wear rates on pads and rotors is unmatched. Due to its excellent release characteristics and controllability, PAGID endurance materials are also often used for sprint races. This material provides very good levels of performance and response at all temperature levels; only slight temperature inputs are required to bring the pad up to its optimum performance level. A favorite with endurance racers at events such as Le Mans, Daytona, Spa, Nurburgring, etc. Due to the exceptional pad life and very low wear on brake discs it has been possible to run 24 hours without a change of pads or discs. This has proved suitable for applications running very high disc temperatures.

Fits These Vehicles: Make Model Build (Year) Front Rear Ferrari 458 Speciale [ceramic brakes] 2013 +   X Ferrari 488 [ceramic brakes] 2015 +   X RSC 1: The Pagid RSC1 is a good street/track compromise for enthusiasts with Carbon-Ceramic Brakes. Used for sprint racing and track days compound with all known types of ceramic brake discs. An ideal combination of cold friction, fade resistance and low thermal oxidation of the disc surface.

A1-183 Girodisc Two-Piece Front Brake Rotors FITMENT: Ferrari 458 Challenge, Front This Girodisc system is a direct replacement for the OEM front CCM rotors on the Ferrari 458 Challenge, although a different brake pad than OEM, with an annulus (pad swept area) of 66 mm or less, must be used1. We suggest the Pagid 8081, the most popular pad used with Girodisc rotors on the Ferrari 458 Challenge. The lower-annulus design of the Girodisc rotors keeps weight low without sacrificing braking performance. Girodisc two-piece floating rotors are lighter than OEM brake rotors. This reduction in rotational mass and unsprung weight allows for quicker acceleration, sharper steering, and faster suspension response. When used with Pagid or PFC performance brake pads and CMS RF-1 brake fluid (available from Competition Motorsport), you have an amazing solution to overheating, cracking and warping rotors. The central hat section of each Girodisc is made from 6061-T6 aircraft specification aluminum. The disc is manufactured from cast iron constructed in the USA, made to the same specification with the same material used by professional racing organizations. The rotors' curved vane design was developed in racing and acts as a centrifugal pump to force cooling air through the disc. The rotor and hat mount together through a floating mount system which utilizes ten high strength alloy steel drive pins manufactured by Girodisc in the USA to their own specifications and are cadmium plated for corrosion resistance. The alloy drive pins transfer the load from the brake action while maintaining the axial and radial float between the disc rotor and hat. The pins are secured by Grade-12 cap screws with hardened washers and mounted with anti-noise spring washers to allow for heat expansion while eliminating the rattle and noise associated with floating rotors. The two-piece Girodisc design allows for disc-only replacement as well, minimizing future replacement costs and delivering outstanding performance. Sold/priced per pair. 1 Note: These Girodisc rotors have a different annulus (pad swept area) than the OEM CCM rotors, to maintain their light weight. A brake pad with an annulus of 66mm or less must be used with these Girodisc rotors. The necessary pad shape is very common, found on the Nissan GT-R, Cadillac CTS-V, and most AMG Mercedes equipped with six-piston calipers. If there's a specific pad and/or compound you're after please, contact us at (844) 438-7244 and we'll get you what you need!

FITS: Ferrari 458 CHALLENGE   Competition Motorsport is an Authorized dealer for GiroDisc products and we are one of the largest stocking dealers in the country.  We ship most products same or next business day to ensure we meet your delivery deadline.   The GiroDisc system is an upgrade to a 2-piece steel rotor and aluminum hat combination and is a direct replacement for the OEM brake disc.  The 2-piece floating disc will bolt directly to the car and work with OEM calipers perfectly.  By upgrading your brakes with these lightweight high-performance replacements as opposed to a big brake kit, your factory bias is maintained as well as your ABS efficiency.  The Giro Disc rotors are lighter than OEM pieces.  The reduction in rotational and unsprung weight allows for quicker acceleration and suspension response.   When used with Pagid or PFC performance brake pads, and Competition Motorsport RF-1 brake fluid (also available from CompetitionMotorsport.com), you have an amazing solution to overheating, cracking and warping rotors. The central hat section of the disc is made from 6061-T6 aircraft specification aluminum.  The disc is manufactured from cast iron which is constructed in the USA and is made to the same specification with the same material used by professional racing organizations.  The rotors curved vane design was developed in racing and acts as a centrifugal pump to force cooling air through the disc.     The rotor and hat mount together through a floating mount system which utilizes 8-10 high strength alloy steel drive pins manufactured by GiroDisc in the USA to our own specifications and are cadmium plated for corrosion resistance.  The alloy drive pins transfer the load from the brake action while maintaining the axial and radial float between the disc rotor and hat.  The pins are secured by grade12 cap screws with hardened washers and mounted with anti-noise spring washers to allow for heat expansion while eliminating the rattle and noise associated with floating rotors.   The 2-piece GiroDisc design allows for rotor only replacement as well to minimize future replacement costs and deliver outstanding performance and cooling.   Sold/Priced per pair.

FITS: FERRARI 458 CHALLENGE REPLACEMENT ROTOR DISC ONLY, DOES NOT INCLUDE ALUMINUM HAT. Competition Motorsport is an Authorized dealer for GiroDisc products and we are one of the largest stocking dealers in the country.  We ship most products same or next business day to ensure we meet your delivery deadline. The GiroDisc replacement rotor system is a direct rotor disc replacement for the Giro Disc 2-piece hat and rotor and no modifications are necessary.   The rotor and hat mount together through a floating mount system which utilizes 8-10 high strength alloy steel drive pins manufactured by GiroDisc in the USA to our own specifications and are cadmium plated for corrosion resistance.  The alloy drive pins transfer the load from the brake action while maintaining the axial and radial float between the disc rotor and hat.  The pins are secured by grade12 cap screws with hardened washers and mounted with anti-noise spring washers to allow for heat expansion while eliminating the rattle and noise associated with floating rotors. The 2-piece GiroDisc design allows for rotor only replacement to minimize replacement costs and deliver outstanding performance and cooling. Sold/Priced per pair.

FITS: FERRARI 458 CHALLENGE REPLACEMENT ROTOR DISC ONLY, DOES NOT INCLUDE ALUMINUM HAT. Competition Motorsport is an Authorized dealer for GiroDisc products and we are one of the largest stocking dealers in the country.  We ship most products same or next business day to ensure we meet your delivery deadline. The GiroDisc replacement rotor system is a direct rotor disc replacement for the Giro Disc 2-piece hat and rotor and no modifications are necessary.   The rotor and hat mount together through a floating mount system which utilizes 8-10 high strength alloy steel drive pins manufactured by GiroDisc in the USA to our own specifications and are cadmium plated for corrosion resistance.  The alloy drive pins transfer the load from the brake action while maintaining the axial and radial float between the disc rotor and hat.  The pins are secured by grade12 cap screws with hardened washers and mounted with anti-noise spring washers to allow for heat expansion while eliminating the rattle and noise associated with floating rotors. The 2-piece GiroDisc design allows for rotor only replacement to minimize replacement costs and deliver outstanding performance and cooling. Sold/Priced per pair.