
Competition Motorsport
CMS Performance RF1 DOT4 622ºF Racing Brake Fluid
from $32.00
CMS Performance RF1 DOT4 Racing Brake Fluid
Real-Life High Boiling Point Without The Real High Price
RF1 Racing Brake Fluid from CMS Performance is a fully-synthetic DOT4 brake fluid formulated to provide extraordinary performance under the most demanding high-temperature racing and track-day conditions. With a dry boiling point of 328º C (622º F), RF1 exceeds all DOT3 & DOT4 requirements and is compatible with all DOT 3, 4, and 5.1 fluids. (Not compatible with DOT5 or mineral-based brake fluids.)
On the race track, brake systems operate at very high sustained temperatures, and there is perhaps no single safety system more important in racing than your brakes. No single part of that system is more critical than brake fluid. At CMS Performance, we got tired of (and a little nervous) using "racing" brake fluid at the race track that didn't live up to its claimed performance when things got hot.
So we did something about it. Manufactured in partnership with Orthene, the brake fluid supplier to many teams in Formula 1, WEC, and other professional series, RF1 Racing Brake Fluid was formulated to maintain consistent viscosity, lubricity, and compressibility at the extreme system temperatures and line pressures found in racing and track days.
The bottom line is this: you can spend more on brake fluid, but you can't buy higher-performance than RF1 Racing Brake Fluid.
RF1 Racing Brake Fluid Details:
Typical dry boiling point: 328º C (622º F)
Typical wet boiling point: 204º C (399º F)
Exceeds DOT3 & DOT4 standards
Bottle size: 500 ml (16.9 fl oz)
Click Here for Product MSDS Sheet
A Word About Flushing Brake Fluid
All brake fluid degrades over time (not mileage), attracting water as it ages, which, at high brake temperatures, can lead to fluid boil and brake fade or failure. That's why the "wet" (aged) boiling point of any brake fluid is substantially lower than the "dry" (new) boiling point.
To maintain maximum braking performance, Competition Motorsport strongly suggests replacing your brake fluid before every track event, but at least every three months if you're consistently racing and/or driving at track days. It's cheap insurance against learning about brake fade the hard way!

Castrol
Castrol React SRF Synthetic Racing Brake Fluid
$109.00
Castrol React SRF Racing Brake Fluid
Castrol React SRF Racing Brake Fluid is an ultra-high performance brake fluid popular with many of the highest performing auto racing teams around the world. The key to Castrol SRF brake fluid's superior performance is its silicon-ester technology. Not only is it less hygroscopic (i.e., it absorbs less water) than typical glycol-based brake fluids, Castrol SRF also reacts chemically with any absorbed water to further reduce its adverse effects on high-temperature braking performance. The result is an almost unheard of 518° F (270° C) wet boiling point -- more than 100° F higher than most other racing brake fluids!
Exceeds SAE 1703, ISO 4925, JIS K2233, FMVSS No. 116 DOT3 and DOT 4 specifications.
Note: Castrol SRF is not a silicone-based brake fluid (e.g., DOT 5) and is compatible with most factory brake systems and fluids. Always follow vehicle manufacturer's recommendations when adding brake fluid.
TYPICAL PROPERTIES:
Dry Boiling Point: 590°F (310°C)
Wet Boiling Point: 518°F (270°C)
Superior anti-vapor lock properties
One-liter (1000ml) bottle

Girodisc
Girodisc Brake Pad Spreader GDPS01
$364.00
Girodisc Brake Pad Spreader
This indispensable tool is used by race teams, shops, and enthusiasts alike who have high performance four- and six-piston calipers. The Girodisc Brake Pad Spreader is designed to easily spread brake pads and pistons to facilitate quick replacement of pads and/or rotors in a shop or racing environment.
No more screwdrivers, pliers, hammers, or C-clamps! This tool will retract the pistons fully and evenly into their bores with one squeeze of the levers.
The Girodisc Brake Pad Spreader was designed to be used with popular racing brake calipers from Brembo, AP Racing, Alcon, and other performance calipers in racing and road use. To help it fit into any caliper, the amount of throw is adjustable.
Insert the spreading plates one way for wider six-piston calipers, then turn the spreader 90o and use the plate sides for four-piston calipers.
The Girodisc Brake Pad Spreader is made from heavy-gauge steel, powder-coated for durability. The slider is cadmium-plated, and nylon pivot bushings ensure smooth action.
The Girodisc Brake Pad Spreader will quickly become an invaluable tool for any race team, shop, or enthusiast who changes pads and rotors frequently.

Girodisc
A1-162 Girodisc 2pc Front Brake Rotors for Shelby GT350/GT350R (2015+)
$1,817.00
A1-162 Girodisc 2pc Front Brake Rotors
FITMENT: Ford Shelby GT350/GT350R (2015+)
This Girodisc system for the Ford Shelby GT350 and GT350R is a direct replacement for the OEM front brake rotors; no modifications are necessary. The rotors will bolt directly to your Shelby and work flawlessly with the OEM calipers. By upgrading your brakes with lightweight, high performance two-piece floating rotors (as opposed to a big brake kit) your factory dialed-in brake bias is maintained as well as your ABS effectiveness and efficiency. Together with our customers, we have thousands of track miles on Girodisc rotors on every conceivable car. They are the go-to rotor for any of our track-day and race-car builds.
Girodisc two-piece floating rotors are lighter than OEM brake rotors. This reduction in rotational mass and unsprung weight allows for quicker acceleration, sharper steering, and faster suspension response.
When used with Pagid or PFC performance brake pads and CMS RF-1 racing brake fluid (available from Competition Motorsport), you have an amazing solution to overheating, cracking and warping rotors.
The central hat section of each Girodisc is made from 6061-T6 aircraft specification aluminum. The disc is manufactured from cast iron constructed in the USA, made to the same specification with the same material used by professional racing organizations. The rotors' curved vane design was developed in racing and acts as a centrifugal pump to force cooling air through the disc.
The rotor and hat mount together through a floating mount system which utilizes ten high strength alloy steel drive pins manufactured by Girodisc in the USA to their own specifications and are cadmium plated for corrosion resistance. The alloy drive pins transfer the load from the brake action while maintaining the axial and radial float between the disc rotor and hat. The pins are secured by Grade-12 cap screws with hardened washers and mounted with anti-noise spring washers to allow for heat expansion while eliminating the rattle and noise associated with floating rotors.
The two-piece Girodisc design allows for disc-only replacement as well, minimizing future replacement costs and delivering outstanding performance.
Sold/priced per pair.

Pagid
Pagid Racing Brake Pads No. 8208
$583.00
Fits These Vehicles
Make
Model
Build (Year)
Front
Rear
Chevrolet
Camaro SS - 4 Piston Brembo caliper
2016 +
X
Chevrolet
Camaro SS - 6 Piston Brembo caliper - upgrade kit
2016 +
X
Chevrolet
Camaro ZL1
2016 +
X
Chevrolet
Corvette C7 base
2014 +
X
Chevrolet
Corvette C7 Z06 [iron brakes]
2015 +
X
Chevrolet
Corvette C7 Z51
2014 +
X
Ford
Mustang Shelby GT350 [6 piston Brembo caliper / 15.5" disc]
2015 +
X
RSL 29:
The PAGID RSL29 (Yellow) is the world-leading endurance brake pad used by most of the winning teams in motorsport. Although designed primarily for endurance racing, many competitors use this material successfully for sprint and short distance races also. RS29 has also found favor in the growing track day market due to the level of control, good cold performance, long life and low disc wear.

Pagid
Pagid Racing Brake Pads No. 8239
from $785.00
Fits These Vehicles
Make
Model
Build (Year)
Front
Rear
Ford
Mustang Shelby GT350 [6 piston Brembo caliper w/ 15.5" rotor]
15 -
X
RSL 29:
The PAGID RSL29 (Yellow) is the world-leading endurance brake pad used by most of the winning teams in motorsport. Although designed primarily for endurance racing, many competitors use this material successfully for sprint and short distance races also. RS29 has also found favor in the growing track day market due to the level of control, good cold performance, long life and low disc wear.
RST 3:The PAGID RST3 is a medium-high friction metal-ceramic compound containing steel and acrylic fibers. It has very low heat conductivity, good initial bite, and excellent modulation and release characteristics. Optimized for rally on tarmac and gravel, GT and Touring cars, and club racing.

Orthene
HALO P1 High Performance Brake Fluid 20oz
$99.00
HALO P1 High Performance Brake Fluid
The World's Most Advanced Racing Brake Fluid
Imagine you're on the race track, hitting the entry to a corner. Your foot hammers down on the brake, and you feel... absolute perfection. That's Halo P1 for you. Developed with Fade Resistant Technology, this specialist brake fluid is the secret sauce for top-tier motorsport enthusiasts worldwide.
Why? Because when you're tearing up the track, the last thing you want is a mushy pedal feel. Halo P1 delivers a low and stable compressibility profile over an extended temperature range, not to mention a crazy-high dry boiling point of 341º C (646º F). All of this is to ensure your brake pedal feel remains as strong and consistent as your lap times.Sold in 20oz Bottles.
Features & Benefits That'll Make You Weep Tears of Joy
Fade Resistant Technology: Keeps your pedal feel consistent, lap after lap, so you can focus on nailing those corners.
Pure Methyl Borate Ester Base: The purity level here is so high, it's like the distilled essence of speed itself, ensuring extreme resistance to compression, even when things get hot (and we mean really hot).
World-Beating Dry Boiling Point: At 341° C (646° F), it's like this fluid laughed in the face of boiling points and set a new standard.
Low Viscosity & High Lubricity: Because your brake system deserves to be as smooth as your driving skills.
What Makes Halo P1 The Secret Weapon?
While other brake fluids are off playing checkers, Halo P1 is mastering chess. It's not just another methyl glycol borate ester brake fluid; it's a revolution in braking performance. With its unique proprietary manufacturing process, it achieves the highest levels of purity and the lowest compressibility possible, remaining constant over a wide temperature range. This is the highest boiling point of any racing brake fluid on the market, folks. And the lubricity? Off the charts, especially at high temperatures.
FAQs That'll Clear the Air
Before you rush off to convert your entire garage to a Halo P1 shrine, let's tackle some of those burning questions you might have:
Can I use Halo P1 in my daily driver? As much as we love the enthusiasm, Halo P1 is a race-only formula. It's like putting a rocket booster on a bicycle – thrilling, but not recommended.
How often should I change my brake fluid with Halo P1? Regular maintenance is key in racing. Check with your team or mechanic, but before every major race is a good rule of thumb.
The Call to Action You've Been Waiting For
So, are you ready to elevate your racing game to legendary status? To feel the rush of confidence as you brake later and harder, knowing your brake fluid won't let you down? It's time to switch to Halo P1. Your podium awaits.

Girodisc
A2-162 Girodisc 2pc Rear Brake Rotors (Ford GT350-GT350R)
$1,817.00
The Girodisc system for the 2015+ Ford Shelby GT350 and GT350R is a direct replacement for the OE rear discs; no modifications are necessary.
The rotors will bolt directly to your car and work flawlessly with OE calipers. By upgrading your brakes with lightweight, high performance two-piece rotors, as opposed to a big brake kit, your factory brake bias is maintained as well as your ABS effectiveness and efficiency. Together with our customers, we have thousands of track miles on Girodisc rotors on every conceivable car. They are the go-to rotor for any of our track- or race-car builds.The central hat section of the Girodisc A2-162 rotor is made from strictly U.S. sourced 6061-T6 aircraft specification aluminum. The disc is made from Girodisc's proprietary cast iron, poured in the USA and machined from start to finish in-house at Girodisc. The rotor utilizes a curved vane design, developed in racing to act as a centrifugal pump to force cooling air through the disc.The rotor and hat have a floating mount system, which utilizes 10 high-strength alloy steel drive pins, manufactured by Girodisc in the USA to their specifications and cadmium plated for a long lasting corrosion resistance. These pins take the load from braking action while maintaining the axial and radial float between the hat and disc. The pins are secured by Grade-12 cap screws with hardened washers. In order to keep the rotors from making noise when cold, the pins are mounted with anti-noise spring washers on the rotor side which allow the rotor to grow with heat expansion but eliminate the rattle and noise associated with floating rotors. This float also allows the rotor to self center between the pads. Once the Girodisc system is in place, simply replace the cast iron rotor ring when needed.Sold/priced per pair.