997 GT3/GT3RS

CMS Performance RF1 DOT4 Racing Brake Fluid Real-Life High Boiling Point Without The Real High Price RF1 Racing Brake Fluid from CMS Performance is a fully-synthetic DOT4 brake fluid formulated to provide extraordinary performance under the most demanding high-temperature racing and track-day conditions. With a dry boiling point of 328º C (622º F), RF1 exceeds all DOT3 & DOT4 requirements and is compatible with all DOT 3, 4, and 5.1 fluids. (Not compatible with DOT5 or mineral-based brake fluids.) On the race track, brake systems operate at very high sustained temperatures, and there is perhaps no single safety system more important in racing than your brakes. No single part of that system is more critical than brake fluid. At CMS Performance, we got tired of (and a little nervous) using "racing" brake fluid at the race track that didn't live up to its claimed performance when things got hot. So we did something about it. Manufactured in partnership with Orthene, the brake fluid supplier to many teams in Formula 1, WEC, and other professional series, RF1 Racing Brake Fluid was formulated to maintain consistent viscosity, lubricity, and compressibility at the extreme system temperatures and line pressures found in racing and track days. The bottom line is this: you can spend more on brake fluid, but you can't buy higher-performance than RF1 Racing Brake Fluid. RF1 Racing Brake Fluid Details: Typical dry boiling point: 328º C (622º F) Typical wet boiling point: 204º C (399º F) Exceeds DOT3 & DOT4 standards Bottle size: 500 ml (16.9 fl oz) Click Here for Product MSDS Sheet A Word About Flushing Brake Fluid All brake fluid degrades over time (not mileage), attracting water as it ages, which, at high brake temperatures, can lead to fluid boil and brake fade or failure. That's why the "wet" (aged) boiling point of any brake fluid is substantially lower than the "dry" (new) boiling point. To maintain maximum braking performance, Competition Motorsport strongly suggests replacing your brake fluid before every track event, but at least every three months if you're consistently racing and/or driving at track days. It's cheap insurance against learning about brake fade the hard way!

Castrol React SRF Racing Brake Fluid Castrol React SRF Racing Brake Fluid is an ultra-high performance brake fluid popular with many of the highest performing auto racing teams around the world.  The key to Castrol SRF brake fluid's superior performance is its silicon-ester technology.  Not only is it less hygroscopic (i.e., it absorbs less water) than typical glycol-based brake fluids, Castrol SRF also reacts chemically with any absorbed water to further reduce its adverse effects on high-temperature braking performance. The result is an almost unheard of 518° F (270° C) wet boiling point -- more than 100° F higher than most other racing brake fluids! Exceeds SAE 1703, ISO 4925, JIS K2233, FMVSS No. 116 DOT3 and DOT 4 specifications. Note: Castrol SRF is not a silicone-based brake fluid (e.g., DOT 5) and is compatible with most factory brake systems and fluids.  Always follow vehicle manufacturer's recommendations when adding brake fluid. TYPICAL PROPERTIES: Dry Boiling Point: 590°F (310°C) Wet Boiling Point: 518°F (270°C) Superior anti-vapor lock properties One-liter (1000ml) bottle

Girodisc Brake Pad Spreader This indispensable tool is used by race teams, shops, and enthusiasts alike who have high performance four- and six-piston calipers. The Girodisc Brake Pad Spreader is designed to easily spread brake pads and pistons to facilitate quick replacement of pads and/or rotors in a shop or racing environment. No more screwdrivers, pliers, hammers, or C-clamps! This tool will retract the pistons fully and evenly into their bores with one squeeze of the levers. The Girodisc Brake Pad Spreader was designed to be used with popular racing brake calipers from Brembo, AP Racing, Alcon, and other performance calipers in racing and road use. To help it fit into any caliper, the amount of throw is adjustable. Insert the spreading plates one way for wider six-piston calipers, then turn the spreader 90o and use the plate sides for four-piston calipers. The Girodisc Brake Pad Spreader is made from heavy-gauge steel, powder-coated for durability. The slider is cadmium-plated, and nylon pivot bushings ensure smooth action. The Girodisc Brake Pad Spreader will quickly become an invaluable tool for any race team, shop, or enthusiast who changes pads and rotors frequently.

ROTOR RINGS ONLY (NO HATS) Need new rings for your Girodisc 350mm 2pc rotors? We got them. Rings come complete with all new hardware and full instructions for re-assembly. Price is for a pair of rings and 2 hardware kits. Additional hardware kits are available separately upon request.

 Pagid Racing Brake Pads No. 2707 Fits These Vehicles: Make Model Build (Year) Front Rear Porsche 996 GT2 02 - 05 X   Porsche 996 GT3 02 - 05 X   Porsche 996 GT3 Cup 02 - 05 X   Porsche 996 GT3 RS [street car] 03 - 05 X   Porsche 997 all models ceramic brakes 05 - 12 X   Porsche 997 GT3 07 - 11 X   Porsche 997 GT3 RS 07 - 12 X   Porsche 997 Turbo 06 - 12 X   Porsche Boxster [987] [ceramic brakes] 05 - 12 X   Porsche Carrera GT 04 - 06 X X Porsche Cayman [987] [ceramic brakes] 06 - 12 X   COMPOUNDS: RSL29, RSC1 Pagid Racing Brake Pads No. 2707 RSL 29: The Pagid RS29 (Yellow) is the world-leading endurance brake pad used by most of the winning teams in motorsport. Although designed primarily for endurance racing, many competitors use this material successfully for sprint and short distance races also. RS29 has also found favor in the growing track day market due to the level of control, good cold performance, long life and low disc wear. RSC 1: The Pagid RSC1 is a good street/track compromise for enthusiasts with Carbon-Ceramic Brakes. Used for sprint racing and track days compound with all known types of ceramic brake discs. An ideal combination of cold friction, fade resistance and low thermal oxidation of the disc surface.

HALO P1 High Performance Brake Fluid The World's Most Advanced Racing Brake Fluid Imagine you're on the race track, hitting the entry to a corner. Your foot hammers down on the brake, and you feel... absolute perfection. That's Halo P1 for you. Developed with Fade Resistant Technology, this specialist brake fluid is the secret sauce for top-tier motorsport enthusiasts worldwide. Why? Because when you're tearing up the track, the last thing you want is a mushy pedal feel. Halo P1 delivers a low and stable compressibility profile over an extended temperature range, not to mention a crazy-high dry boiling point of 341º C (646º F). All of this is to ensure your brake pedal feel remains as strong and consistent as your lap times.Sold in 20oz Bottles. Features & Benefits That'll Make You Weep Tears of Joy Fade Resistant Technology: Keeps your pedal feel consistent, lap after lap, so you can focus on nailing those corners. Pure Methyl Borate Ester Base: The purity level here is so high, it's like the distilled essence of speed itself, ensuring extreme resistance to compression, even when things get hot (and we mean really hot). World-Beating Dry Boiling Point: At 341° C (646° F), it's like this fluid laughed in the face of boiling points and set a new standard. Low Viscosity & High Lubricity: Because your brake system deserves to be as smooth as your driving skills. What Makes Halo P1 The Secret Weapon? While other brake fluids are off playing checkers, Halo P1 is mastering chess. It's not just another methyl glycol borate ester brake fluid; it's a revolution in braking performance. With its unique proprietary manufacturing process, it achieves the highest levels of purity and the lowest compressibility possible, remaining constant over a wide temperature range. This is the highest boiling point of any racing brake fluid on the market, folks. And the lubricity? Off the charts, especially at high temperatures. FAQs That'll Clear the Air Before you rush off to convert your entire garage to a Halo P1 shrine, let's tackle some of those burning questions you might have: Can I use Halo P1 in my daily driver? As much as we love the enthusiasm, Halo P1 is a race-only formula. It's like putting a rocket booster on a bicycle – thrilling, but not recommended. How often should I change my brake fluid with Halo P1? Regular maintenance is key in racing. Check with your team or mechanic, but before every major race is a good rule of thumb. The Call to Action You've Been Waiting For So, are you ready to elevate your racing game to legendary status? To feel the rush of confidence as you brake later and harder, knowing your brake fluid won't let you down? It's time to switch to Halo P1. Your podium awaits.

Pagid Racing Brake Pads No. 8006 Fits These Vehicles Make Model Build (Year) Front Rear Porsche 997 3.6 C & 3.6 C4 08 - 11   X Porsche 997 all models ceramic brakes 05 - 12   X Porsche 997 GT3 07 - 11   X Porsche 997 GT3 Cup [19 mm thick pads] 05 - 12   X Porsche 997 GT3 Rally 05 - 12   X Porsche 997 GT3 RS 07 - 12   X Porsche 997 Turbo 06 - 12   X   RSL 29: The PAGID RSL29 (Yellow) is the world-leading endurance brake pad used by most of the winning teams in motorsport. Although designed primarily for endurance racing, many competitors use this material successfully for sprint and short distance races also. RS29 has also found favor in the growing track day market due to the level of control, good cold performance, long life and low disc wear. RS 14: The PAGID RS14 (Black) is a high friction value ceramic compound with very good modulation and high fade resistance. A very popular, aggressive pad with strong initial bite and high torque. In addition to the track-day environment, RS14 has shown success in short- to medium-distance circuit racing as well as gravel and tarmac rallying. RSC 1: The Pagid RSC1 is a good street/track compromise for enthusiasts with Carbon-Ceramic Brakes. Used for sprint racing and track days compound with all known types of ceramic brake discs. An ideal combination of cold friction, fade resistance and low thermal oxidation of the disc surface. RST 3: The PAGID RST3 is a medium-high friction metal-ceramic compound containing steel and acrylic fibers. It has very low heat conductivity, good initial bite, and excellent modulation and release characteristics. Optimized for rally on tarmac and gravel, GT and Touring cars, and club racing.

The Girodisc system is an upgrade to a 350mm two-piece steel rotor and aluminum hat combination, a direct replacement for the OEM brake disc. The two-piece floating disc will bolt directly to the car and work with OEM calipers perfectly. By upgrading your brakes with these lightweight high-performance replacements -- as opposed to a big brake kit -- your factory brake bias is maintained as well as your ABS efficiency. Girodisc rotors are lighter than the OEM rotors, reducing rotational and unsprung weight for quicker acceleration and suspension response. When used with Pagid or PFC performance brake pads and Competition Motorsport RF1 racing brake fluid (also available from Competition Motorsport), you have an amazing solution to overheating, cracking and warping rotors. The central hat section of the disc is made from 6061-T6 aircraft specification aluminum. The disc is manufactured in the USA from cast iron, made to the same specification and with the same material used by professional racing organizations. The rotor's curved-vane design was developed in racing and acts as a centrifugal pump to force cooling air through the disc. The rotor and hat mount together through a floating mount system which utilizes 8-10 high strength alloy steel drive pins manufactured by GiroDisc in the USA to our own specifications and are cadmium plated for corrosion resistance. The alloy drive pins transfer the load from braking while maintaining the axial and radial float between the disc rotor and hat. The pins are secured by Grade 12 cap screws with hardened washers and mounted with anti-noise spring washers to allow for heat expansion while eliminating the rattle and noise typically associated with floating rotors. The two-piece Girodisc design allows for rotor-ring only replacement to minimize future replacement costs. Priced per pair

Goodridge G-Stop High Performance Stainless Brake Lines This Kit Is For: Porsche 996 (1997-2004 All) Porsche 997 (2005-12 All, including GT2/GT3/GT3RS) Goodridge G-Stop high performance brake lines for the Porsche 996 & 997 consist of the finest quality PTFE inner hose covered by a braided stainless steel outer casing. This gives you a much firmer, more responsive brake pedal by eliminating the “spongy” feel that often accompanies stock rubber brake lines, making them ideal for the very high brake pressures seen during HPDE track days. G-Stop High Performance Brake lines are abrasion and corrosion resistant so they last a long time under harsh conditions. Goodridge G-Stop high performance brake lines are direct bolt-on replacements for all of the rubber brake lines in your Porsche's brake system. Four brake lines are included in each kit, with hose ends and brake line brackets that match the car’s original equipment.  Conforming to Federal Motor Vehicle Safety Standard Number 106, Goodridge G-Stop high performance brake lines are U.S. DOT certified and T.U.V. approved. All Goodridge G-Stop brake lines go through a nine-point Quality Assurance testing process that includes measuring tensile strength and the ability to sustain line pressures to 3,000 psi. Features: Precise fit for your Porsche Greater braking efficiency Resistance to abrasion and corrosion Firmer pedal under heavy braking Added reliability, safety and brilliant looks Technically superior and race proven DOT, TUV, ADR, DEKRA, ARAICCC, ISO9001 Accredited. FMVSS 106 compliant, DOT approved   Brake components should be installed by a competent mechanic in a professional manner.  Incorrect installation of brake components can cause a major safety problem or an accident.

PFC Brake Pads 1299.XX.18.44 REAR PFC 11 COMPOUND A new generation sprint and medium-distance friction compound, giving you the ultimate in control with superior disc conditioning. Developed from the PFC 01 compound with improved bite, modulation, and release characteristics. It is ultra smooth, developed to reduce wheel locking at the end of a stop while giving more cold and hot bite than the endurance oriented PFC 08 compound.¬†¬†PFC 08 COMPOUND One of PFC's most popular compounds which came to fame in Endurance Sports Car and GT racing due to its performance in applications where smooth initial bite is a must. PFC 08 has a slight friction rise with temperature, excellent release and modulation characteristics. Despite its considerable performance, PFC 08 has the lowest wear rate of all PFC compounds and can easily match the wear characteristics of competitors' materials but with much higher bite and consistent performance across a broad temperature range. PFC 332 COMPOUND 332 has been formulated with lower bite and torque for rear applications.With smooth release, the 332 offers excellent stability and control.The 332 has been designed to work with ABS applications, and has exceptionally low wear rates.   FITMENT (Iron Rotors Only) 997 & 997.2 GT3/GT3RS 997 & 997.2 Turbo 996 GT3¬†  

RT RE10*:RE10 is the ultimate endurance race compound offering a balance of excellent stopping power, low thermal conductivity, extremely low pad and disc wear. Utilizing the latest friction material technology, RE10 offers consistent performance under the most demanding of environments. Typical Applications: Professional Endurance Racing, Club Racing, and HPDE on high demand brake platforms *Denotes a "race only" pad. Running a "racing use only" pad on the street could produce excessive noise and dust. Disc wear could be accelerated if driven at cold temperatures or used in the incorrect temperature range. Racing pads are designed to work in specific temperature ranges so it is important to choose the desired compound for the correct environment the vehicle will be used in. Pad Compounds are run on a brake dynamometer over multiple brake applications (stops) to test the materials in a controlled environment for the most accurate data. Wear rates and temperatures can be influenced by car setup, grip levels, track layout/configuration and many other variables.

RT RE10*:RE10 is the ultimate endurance race compound offering a balance of excellent stopping power, low thermal conductivity, extremely low pad and disc wear. Utilizing the latest friction material technology, RE10 offers consistent performance under the most demanding of environments. Typical Applications: Professional Endurance Racing, Club Racing, and HPDE on high demand brake platforms *Denotes a "race only" pad. Running a "racing use only" pad on the street could produce excessive noise and dust. Disc wear could be accelerated if driven at cold temperatures or used in the incorrect temperature range. Racing pads are designed to work in specific temperature ranges so it is important to choose the desired compound for the correct environment the vehicle will be used in. Pad Compounds are run on a brake dynamometer over multiple brake applications (stops) to test the materials in a controlled environment for the most accurate data. Wear rates and temperatures can be influenced by car setup, grip levels, track layout/configuration and many other variables.

PFC Brake Pads  7819.xx.17.44 PFC 11 COMPOUND A new generation sprint and medium distance friction material, giving you the ultimate in control with superior disc conditioning. Developed from PFC 01 compound with improved bite, modulation, and release characteristics. It is ultra smooth and developed to reduce wheel locking at the end of a stop while giving more cold and hot bite than the endurance oriented PFC 08 compound. Brake with confidence, with the ultimate control and modulation. PFC 331 COMPOUND 331 is the next generation of PFC endurance material. Improved control with ABS, and gentle on discs. The 331 Carbon Metallic ® compound has been developed with higher initial bite than PFC’s renowned 08 endurance compound. The 331 has improved release, and continues to offer exceptional control and feel. It boasts low wear rate and exceptional disc conditioning.

ROTOR RINGS ONLY (NO HATS) Need new rings for your Girodisc A2-032 rear rotors? We got them. Rings come complete with all new hardware and full instructions for re-assembly. Price is for a pair of rings and 2 hardware kits. Additional hardware kits are available separately upon request.

PFC Brake Pads 991.08.17.44 FRONT PFC 08 COMPOUND One of PFC's most popular compounds which came to fame in Endurance Sports Car and GT racing due to its performance in applications where smooth initial bite is a must. PFC 08 has a slight friction rise with temperature, excellent release and modulation characteristics. Despite its considerable performance, PFC 08 has the lowest wear rate of all PFC compounds and can easily match the wear characteristics of competitors' materials but with much higher bite and more consistent performance across a broad temperature range.   FITMENT (Iron Rotors Only): Porsche 997.1 & 997.2 GT3/GT3RS Porsche 997 Turbo Porsche 996 GT3 ¬† ¬† ¬† ¬†

A1-019 Girodisc 2pc Front Brake Rotors (350mm) FITMENT: Direct replacement for Porsche 997.1 and 996 GT2/GT3 factory iron front rotors Competition Motorsport is an authorized dealer for Girodisc products. As one of the largest stocking dealers in the country, we ship most products the same or next business day to ensure we meet your delivery deadline. This Girodisc system upgrades your Porsche's OEM brakes to a two-piece steel disc and aluminum hat. This two-piece "floating rotor" design will bolt directly to your GT2 or GT3 front and work flawlessly with the OEM calipers. Upgrading your brakes to lightweight, high-performance Girodisc rotors, you maintain the factory brake bias and ABS effectiveness. Each rotor is 5.6 pounds lighter than an OEM rotor, reducing rotational and unsprung mass giving you stronger braking and faster suspension response. Combined with Pagid or PFC performance brake pads and Competition Motorsport RF-1 brake fluid, Girodisc rotors are the ultimate solution to overheated, cracked, warped rotors that result from high-performance driving. The central hat of the rotor is made from 6061-T6 aircraft aluminum. The disc is manufactured in the USA from the same cast iron used by professional racing organizations. Its curved-vane design, developed in racing, acts like a centrifugal pump forcing cool air through the disc. The disc and hat mount together through a floating mount system using ten cadmium plated, high-strength alloy steel drive pins manufactured by Girodisc. These drive pins transfer braking load while maintaining axial and radial float between the disc and hat to allow for heat expansion. Anti-noise spring washers eliminate the noise typically associated with floating rotors. This two-piece Girodisc design allows for disc-only replacement, reusing the hat to minimize maintenance costs. Sold/priced per pair.