991 GT3/GT3RS/GT2RS

AP Racing 410x36mm Two-Piece Front Floating Racing Brake Rotors Fit The Following Cars (w/ OEM Iron Rotors or PCCB Rotors) Porsche 991 GT2RS PCCB (Front) Porsche 991 GT3 PCCB (Front) Porsche 991 GT3RS PCCB (Front) Porsche 718 / 982 GT4RS PCCB or Iron (Front) Porsche 718 GT4 PCCB (Front) Sold/priced per pair. AP Racing by Essex 2-piece Competition J Hook front iron disc pair for 991 GT3/RS and 718 GT4/Spyder RS to replace PCCB discs. 410x36mm (16.14" x 1.40") Huge increase in airflow, cooling capacity, and durability vs. OEM PCCB discs Drastically less expense long-term running costs vs. PCCB Must use the standard front 991 GT3/RS pad shape used in OEM iron system (not compatible with OE PCCB pad shape) Over twice as many internal cooling vanes as the OEM PCCB's Weighs almost the same as the OEM 380x34mm iron discs, despite much larger size Designed for: club racing, time trial, auto-x, HPDE Works with OEM calipers and wheels, no modifications required Ultralight, fully floating, anodized billet aluminum hat with float control/anti-rattle clips

AP Racing 390x32mm 2-piece J Hook Rear Brake Rotors - Porsche (OEM PCCB) Fit The Following Cars (w/ OEM PCCB Rotors) Porsche 992 GT3 (Rear) Porsche 992 GT3RS (Rear) Porsche 718/982 GT4RS (Rear) Porsche 991 GT2RS/GT3/GT3RS (Rear) Porsche 981 GT4 (Rear) Sold/priced per pair. AP Racing 2-piece Competition J Hook rear iron disc pair for 991/992 GT3/RS and 718 GT4/Spyder RS to replace PCCB discs. 390 x 32mm (15.35" x 1.26") Huge increase in airflow, cooling capacity, and durability vs. OEM PCCB discs Drastically less expense long-term running costs vs. PCCB Must useGT3/RS Iron disc pad shape used in OEM iron system (not compatible with OE PCCB Pad shape) Allows normal function of OEM parking brake 100% more internal cooling vanes vs the OEM PCCB's Same weight as OEM 380 x 34mm iron discs, despite larger size Designed for: club racing, time trial, auto-x, HPDE Works with OEM calipers and wheels, no modifications required Ultralight, fully floating, anodized billet aluminum hat with float control/anti-rattle clips Bedding and preparation of AP Racing J Hook Disc Properly preparing your new brake discs before heavy use is extremely important. The goal of bedding-in your brake pads and discs is to mate them together properly and prepare them for heavy use.  When prepared properly, or bed-in, your pads will transfer a thin layer of material to the disc face (transfer layer).  The pads in your caliper will then actually ride on that thin layer of pad material you’ve put down on the rotor, rather than rubbing directly on the iron rotor face.  A good transfer layer is going to give you superior brake pedal feel, less noise, superior pad wear, and lower the chances of cracking your discs. Important Notes- PLEASE READ! First, make sure you are on a closed course to perform a proper bed-in.  Do NOT perform the procedure on public roads.  You need a stretch of asphalt with long straights, good visibility, and no potential obstructions.  Make sure you are in a position to safely and repeatedly attain the necessary speeds to perform the bed-in procedure.  A controlled racetrack is the best place to perform this procedure.  AP Racing and Competition Motorsport in no way suggest or condone speeding on public roads or breaking the law in your car, nor do we take responsibility for any damage or injury that occurs as a result of using our product or these procedures.  You are performing the bed-in procedure at your own risk.  During these procedures, it’s critical that you never come to a complete stop with your foot on the brake pedal.  If you have brake ducts on your car, you may want to block them off to allow your brake system to heat up easily. The procedure outlined below is a generic procedure for most types of mild race pad.  Please check your pad manufacturer’s recommended bed-in procedure. Accelerate to approximately 60mph and then decelerate down to 5 mph.  If your car has ABS, you should try to hold the brakes at a point just before ABS intervention.  Once the car slows to 5mph, immediately accelerate back up to about 60mph, and brake again to roughly 5mph.  Repeat this series of stopping and accelerating 8 to 10 times.  Again, do not come to a complete stop with your foot on the brake pedal. Cool the brake system down by cruising at 45mph+ for 5 to 10 minutes. Visually inspect your discs.  They should be a blue/grey color (instead of shiny silver), and have an even layer of pad material across and around the entire rotor face. If the AP Racing rotors don’t have a layer of pad material on them, perform another series of stops in the manner outlined above.  

Performance Friction PFC 410.069.63-64 410mm Two-Piece Front Floating Racing Brake Rotors Fit The Following Cars (w/ OEM Iron Rotors or PCCB Rotors) Porsche 991 GT2RS PCCB (Front) Porsche 991 GT3 PCCB (Front) Porsche 991 GT3RS PCCB (Front) Porsche 718 / 982 GT4RS PCCB or Iron (Front) Porsche 718 GT4 PCCB (Front) PFC the manufacturer of Porsche Cup braking systems developed a 410mm front rotor replacement kit that is a direct replacement for the OEM 991 GT or 718 GT4 PCCB Brake rotors or OEM 718 / 982 GT4RS with PCCB or Iron rotors.  Performance Friction PFC V3 Disks with Zero Failure Technology Unique Rotor and Hat interface, eliminating most hardware. The elimination of hardware reduces weight, complexity, and installation time for less down time and more seat time on the track.  Replace your rotor discs in minutes with a flat head screwdriver PFC metallurgy specified for high Thermal stability and mechanical strength for increased longevity 48 vane geometry engineered for increased airflow for increased brake cooling during the heat of the battle while on track Patented slot pattern for increased initial bit and pad surface conditioning Lightweight forged hard anodized aluminum hat for increased durability and performance The two-piece PFC V3 design allows for disc-only replacement as well, minimizing future replacement costs and delivering outstanding performance. Sold/priced per pair.

Performance Friction PFC 390.075.63-64 390mm Two-Piece Rear Floating Racing Brake Rotors Fit The Following Cars (w/ OEM PCCB Rotors) Porsche 992 GT3 (Rear) Porsche 992 GT3RS (Rear) Porsche 718/982 GT4RS (Rear) Porsche 991 GT2RS/GT3/GT3RS (Rear) Porsche 981 GT4 (Rear) PFC the manufacturer of Porsche Cup braking systems developed a 390x32 mm rear rotor replacement kit that is a direct replacement for the OEM Steel Brake rotors.  Performance Friction PFC V3 Disks with Zero Failure Technology Unique Rotor and Hat interface, eliminating most hardware. The elimination of hardware reduces weight, complexity, and installation time for less down time and more seat time on the track.  Replace your rotor discs in minutes with a flat head screwdriver PFC metallurgy specified for high Thermal stability and mechanical strength for increased longevity 48 vane geometry engineered for increased airflow for increased brake cooling during the heat of the battle while on track Patented slot pattern for increased initial bit and pad surface conditioning Lightweight forged hard anodized aluminum hat for increased durability and performance The two-piece PFC V3 design allows for disc-only replacement as well, minimizing future replacement costs and delivering outstanding performance. PFC’s V3 discs are optimized to ensure the highest level of performance, wear and durability for your Porsche’s braking system.  These high-performance OEM replacement assemblies now feature aluminium hats in both front and rear, similar to the original. There is a saving of over one pound by trimming excess material from the unused areas around the disc in our new V3 ZeroFailures™ design, which will allow for disc changes in a matter of seconds with a flat head screwdriver. Sold/priced per pair.

AP Racing 380x30mm 2-piece J Hook Rear Brake Rotors for Porsche (OEM Iron) Fit The Following Cars (w/ OEM Iron Rotors) Porsche 992 GT3 (Rear) Porsche 992 GT3RS (Rear) Porsche 718/982 GT4RS (Rear) Porsche 991 GT2RS/GT3/GT3RS (Rear) Porsche 981 GT4 (Rear) Sold/priced per pair. AP Racing 2-piece Competition J Hook rear disc pair for 991.1 & 991.2 GT3 (including GT3RS), 992 GT3, and 718 GT4 and GT4 RS with iron discs 380x30mm (14.96" x 1.18") 72 Vane, D67 radial depth Huge increase in airflow, cooling capacity, and durability vs. OEM discs Saves 3-4 lbs. unsprung weight per side Retains full parking brake functionality Designed for: club racing, time trial, auto-x, HPDE Works with OEM calipers, no modifications required Ultralight, fully floating, anodized billet aluminum hat with float control/anti-rattle clips Sold/priced per pair. Bedding and preparation of AP Racing J Hook Disc Properly preparing your new brake discs before heavy use is extremely important. The goal of bedding-in your brake pads and discs is to mate them together properly and prepare them for heavy use.  When prepared properly, or bed-in, your pads will transfer a thin layer of material to the disc face (transfer layer).  The pads in your caliper will then actually ride on that thin layer of pad material you’ve put down on the rotor, rather than rubbing directly on the iron rotor face.  A good transfer layer is going to give you superior brake pedal feel, less noise, superior pad wear, and lower the chances of cracking your discs. Important Notes- PLEASE READ! First, make sure you are on a closed course to perform a proper bed-in.  Do NOT perform the procedure on public roads.  You need a stretch of asphalt with long straights, good visibility, and no potential obstructions.  Make sure you are in a position to safely and repeatedly attain the necessary speeds to perform the bed-in procedure.  A controlled racetrack is the best place to perform this procedure.  AP Racing and Competition Motorsport in no way suggest or condone speeding on public roads or breaking the law in your car, nor do we take responsibility for any damage or injury that occurs as a result of using our product or these procedures.  You are performing the bed-in procedure at your own risk.  During these procedures, it’s critical that you never come to a complete stop with your foot on the brake pedal.  If you have brake ducts on your car, you may want to block them off to allow your brake system to heat up easily. The procedure outlined below is a generic procedure for most types of mild race pad.  Please check your pad manufacturer’s recommended bed-in procedure. Accelerate to approximately 60mph and then decelerate down to 5 mph.  If your car has ABS, you should try to hold the brakes at a point just before ABS intervention.  Once the car slows to 5mph, immediately accelerate back up to about 60mph, and brake again to roughly 5mph.  Repeat this series of stopping and accelerating 8 to 10 times.  Again, do not come to a complete stop with your foot on the brake pedal. Cool the brake system down by cruising at 45mph+ for 5 to 10 minutes. Visually inspect your discs.  They should be a blue/grey color (instead of shiny silver), and have an even layer of pad material across and around the entire rotor face. If the AP Racing rotors don’t have a layer of pad material on them, perform another series of stops in the manner outlined above.

Performance Friction PFC 380.075.63-64 380mm Two-Piece Rear Floating Racing Brake Rotors Fit The Following Cars (w/ OEM Iron Rotors) Porsche 992 GT3 (Rear) Porsche 992 GT3RS (Rear) Porsche 718/982 GT4RS (Rear) Porsche 991 GT2RS/GT3/GT3RS (Rear) Porsche 981 GT4 (Rear) PFC the manufacturer of Porsche Cup braking systems developed a 380x30 mm rear rotor replacement kit that is a direct replacement for the OEM Steel Brake rotors.  Performance Friction PFC V3 Disks with Zero Failure Technology Unique Rotor and Hat interface, eliminating most hardware. The elimination of hardware reduces weight, complexity, and installation time for less down time and more seat time on the track.  Replace your rotor discs in minutes with a flat head screwdriver PFC metallurgy specified for high Thermal stability and mechanical strength for increased longevity 48 vane geometry engineered for increased airflow for increased brake cooling during the heat of the battle while on track Patented slot pattern for increased initial bit and pad surface conditioning Lightweight forged hard anodized aluminum hat for increased durability and performance The two-piece PFC V3 design allows for disc-only replacement as well, minimizing future replacement costs and delivering outstanding performance. PFC’s V3 discs are optimized to ensure the highest level of performance, wear and durability for your Porsche’s braking system.  These high-performance OEM replacement assemblies now feature aluminium hats in both front and rear, similar to the original. There is a saving of over one pound by trimming excess material from the unused areas around the disc in our new V3 ZeroFailures™ design, which will allow for disc changes in a matter of seconds with a flat head screwdriver. Sold/priced per pair.

Performance Friction PFC 380.070.63-64 380mm Two-Piece Front Floating Racing Brake Rotors Fit The Following Cars (w/ OEM Iron Rotors) Porsche 991 GT3 (Front) Porsche 991 GT3RS (Front) Porsche 981 GT4 (Front) PFC the manufacturer of Porsche Cup braking systems developed a 380x34mm front rotor replacement kit that is a direct replacement for the OEM Iron Brake rotors.  Performance Friction PFC V3 Discs with Zero Failure Technology Unique Rotor and Hat interface, eliminating most hardware. The elimination of hardware reduces weight, complexity, and installation time for less down time and more seat time on the track.  Replace your rotor discs in minutes with a flat head screwdriver PFC metallurgy specified for high Thermal stability and mechanical strength for increased longevity 48 vane geometry engineered for increased airflow for increased brake cooling during the heat of the battle while on track Patented slot pattern for increased initial bit and pad surface conditioning Lightweight forged hard anodized aluminum hat for increased durability and performance The two-piece PFC V3 design allows for disc-only replacement as well, minimizing future replacement costs and delivering outstanding performance. Sold/priced per pair.

Girodisc A2-154 390mm Rear Iron Rotor Conversion Fits The Following Cars With OEM PCCB: Porsche 991.1 and 991.2 GT3 Porsche 991.1 and 991.2 GT3RS Porsche 991.2 GT2RS Porsche 718 Cayman GT4RS This 390mm Girodisc conversion system is a rear rotor direct replacement for any Porsche 991 GT3, GT3RS, GT2RS, and GT4RS originally equipped with PCCB brakes. These two-piece floating iron rotors will bolt directly to the car and work with your OEM calipers perfectly. By upgrading your brakes with these lightweight, high-performance Girodisc rotors (paired with the A1-154 front rotors), your factory brake bias and ABS efficiency are maintained. The low rotational and unsprung weight allows for quicker acceleration and transient suspension response. Most racers replace the factory PCCBs with steel two-piece rotors to avoid the inevitable damage to the fragile carbon ceramic discs when swapping wheels at the track! When used with Pagid or PFC performance brake pads and CMS RF1 racing brake fluid, you have an powerful, durable solution to cracked or broken carbon-ceramic rotors at a fraction of the cost of replacing the factory PCCB units. The central hat section of each Girodisc is made from 6061-T6 aircraft specification aluminum. The disc is manufactured from cast iron constructed in the USA, made to the same specification with the same material used by professional racing organizations. The rotors' curved vane design was developed in racing and acts as a centrifugal pump to force cooling air through the disc. The rotor and hat mount together through a floating mount system which utilizes ten high strength alloy steel drive pins manufactured by Girodisc in the USA to their own specifications and are cadmium plated for corrosion resistance. The alloy drive pins transfer the load from the brake action while maintaining the axial and radial float between the disc rotor and hat. The pins are secured by class 12.9 cap screws with hardened washers and mounted with anti-noise spring washers to allow for heat expansion while eliminating the rattle and noise associated with floating rotors. The two-piece Girodisc design allows for disc-only replacement as well, minimizing future replacement costs and delivering outstanding performance. Sold/priced per pair.

A1-154 Girodisc Two-Piece 410mm Front Brake Rotors FITMENT: Porsche GT3 (991) w/ factory PCCB Porsche GT3RS (991) w/ factory PCCB Porsche GT2RS (991) w/ factory PCCB Porsche GT4RS (718) w/ factory PCCB This 410mm Girodisc conversion system is a direct front rotor replacement for the Porsche 991.1 or 991.2 GT3, GT3RS, GT2RS, and GT4RS originally equipped with PCCB brakes. These two-piece floating iron rotors with aluminum hats will bolt directly to your Porsche and work flawlessly with the OEM front calipers. You must use must use the pad shape used on the 991 GT3 with iron rotors. The annulus (pad swept height) of these rotors is smaller than the PCCBs to keep rotor weight low and allow far better pad selection. By upgrading your brakes with lightweight, high-performance Girodisc rotors, especially when paired with Girodisc A2-154 rear rotors, your Porsche's factory brake bias and ABS efficiency are maintained. The low rotational mass and unsprung weight of Girodisc rotors allows for quick acceleration and fast transient suspension response. Most racers replace the factory PCCBs with Girodisc rotors to avoid the inevitable damage to fragile carbon-ceramic discs when swapping wheels at the track. We suggest using these rotors with these Pagid 4924 or PFC brake pad profiles normally used in the Porsche 991 GT3 without PCCB. When combined with Competition Motorsport RF1 Racing brake fluid or the New HALO P1 High Performance Brake Fluid, you'll have an extremely reliable and durable solution to cracked or broken carbon-ceramic rotors at a fraction of the cost of factory PCCBs. The central hat section of the Girodisc is made from 6061-T6 aircraft specification aluminum. The disc is manufactured from cast iron constructed in the USA, made to the same specification with the same material used by professional racing organizations. The rotors' curved vane design was developed in racing and acts as a centrifugal pump to force cooling air through the disc. The rotor and hat mount together through a floating mount system which utilizes ten high strength alloy steel drive pins manufactured by Girodisc in the USA to their own specifications and are cadmium plated for corrosion resistance. The alloy drive pins transfer the load from the brake action while maintaining the axial and radial float between the disc rotor and hat. The pins are secured by Grade-12 cap screws with hardened washers and mounted with anti-noise spring washers to allow for heat expansion while eliminating the rattle and noise associated with floating rotors. The two-piece Girodisc design allows for disc-only replacement as well, minimizing future replacement costs and delivering outstanding performance. Sold/priced per pair.

A1-146 Girodisc Two-Piece Front Brake Rotors FITMENT: Porsche 991 GT3/GT3RS/GT2RS, Front (2014+) with steel brakes The Girodisc system is a direct replacement for the OEM front rotors on the Porsche 991 GT3, GT3RS, and GT2RS with OEM iron rotors. No modifications are necessary, including full use of factory unmodified pads unlike most aftermarket solutions for this application. The GIrodisc rotors will bolt directly to your car and work with OEM calipers perfectly. By upgrading your brakes with lightweight, high performance replacements -- as opposed to a big brake kit -- your factory brake bias and ABS efficiency are preserved. The central hat section of the disc is made from 6061-T6 aircraft specification aluminum. The disc is manufactured from cast iron constructed in the USA, made to the same specification with the same material used by professional racing organizations. The rotors' curved vane design was developed in racing and acts as a centrifugal pump to force cooling air through the disc. The rotor and hat mount together through a floating mount system which utilizes ten high strength alloy steel drive pins manufactured by Girodisc in the USA to their own specifications and are cadmium plated for corrosion resistance. The alloy drive pins transfer the load from the brake action while maintaining the axial and radial float between the disc rotor and hat. The pins are secured by Grade-12 cap screws with hardened washers and mounted with anti-noise spring washers to allow for heat expansion while eliminating the rattle and noise associated with floating rotors. The two-piece Girodisc design allows for disc-only replacement as well, minimizing future replacement costs and delivering outstanding performance. Sold/priced per pair.

A2-146 Girodisc Two-Piece Rear Brake Rotors FITMENT: Porsche 991 GT3 / GT3RS / GT2RS, Rear w/ Cast Iron Brakes This Girodisc system is a direct replacement for the OEM Porsche cast iron rotors on the 991 GT3, GT3RS, and GT2RS. No modifications are necessary, allows use of factory unmodified pads (unlike most aftermarket solutions for this application). The Girodisc rotors will bolt directly to the car and work with OEM calipers perfectly. By upgrading your brakes with lightweight high performance replacements as opposed to a big brake kit, your factory-tuned brake bias is maintained as well as your ABS efficiency. Girodisc two-piece floating rotors are lighter than OEM brake rotors. This reduction in rotational mass and unsprung weight allows for quicker acceleration, sharper steering, and faster suspension response. When used with Pagid or PFC performance brake pads and CMS RF-1 brake fluid (available from Competition Motorsport), you have an amazing solution to overheating, cracking and warping rotors. The central hat section of each Girodisc is made from 6061-T6 aircraft specification aluminum. The disc is manufactured from cast iron constructed in the USA, made to the same specification with the same material used by professional racing organizations. The rotors' curved vane design was developed in racing and acts as a centrifugal pump to force cooling air through the disc. The rotor and hat mount together through a floating mount system which utilizes ten high strength alloy steel drive pins manufactured by Girodisc in the USA to their own specifications and are cadmium plated for corrosion resistance. The alloy drive pins transfer the load from the brake action while maintaining the axial and radial float between the disc rotor and hat. The pins are secured by class 12.9 cap screws with hardened washers and mounted with anti-noise spring washers to allow for heat expansion while eliminating the rattle and noise associated with floating rotors. The two-piece Girodisc design allows for disc-only replacement as well, minimizing future replacement costs and delivering outstanding performance. Sold/priced per pair.

AP Racing 390x32mm Replacement Rear Floating Racing Brake Rotor Rings Fit The Following Cars (w/ OEM PCCB Rotors)- Center hat Excluded, rotor disc only. Replacement Disc Only For AP Racing 13.01.20026 Porsche 992 GT3 (Rear) Porsche 992 GT3RS (Rear) Porsche 718/982 GT4RS (Rear) Porsche 991 GT2RS/GT3/GT3RS (Rear) Porsche 981 GT4 (Rear) Sold/priced per pair. 390x32mm (15.35" x 1.25") 72 Vane, D66, J Hook Right Hand Iron Racing Brake Disc Bedding and preparation of AP Racing J Hook Disc Properly preparing your new brake discs before heavy use is extremely important. The goal of bedding-in your brake pads and discs is to mate them together properly and prepare them for heavy use.  When prepared properly, or bed-in, your pads will transfer a thin layer of material to the disc face (transfer layer).  The pads in your caliper will then actually ride on that thin layer of pad material you’ve put down on the rotor, rather than rubbing directly on the iron rotor face.  A good transfer layer is going to give you superior brake pedal feel, less noise, superior pad wear, and lower the chances of cracking your discs. Important Notes- PLEASE READ! First, make sure you are on a closed course to perform a proper bed-in.  Do NOT perform the procedure on public roads.  You need a stretch of asphalt with long straights, good visibility, and no potential obstructions.  Make sure you are in a position to safely and repeatedly attain the necessary speeds to perform the bed-in procedure.  A controlled racetrack is the best place to perform this procedure.  AP Racing and Competition Motorsport in no way suggest or condone speeding on public roads or breaking the law in your car, nor do we take responsibility for any damage or injury that occurs as a result of using our product or these procedures.  You are performing the bed-in procedure at your own risk.  During these procedures, it’s critical that you never come to a complete stop with your foot on the brake pedal.  If you have brake ducts on your car, you may want to block them off to allow your brake system to heat up easily. The procedure outlined below is a generic procedure for most types of mild race pad.  Please check your pad manufacturer’s recommended bed-in procedure. Accelerate to approximately 60mph and then decelerate down to 5 mph.  If your car has ABS, you should try to hold the brakes at a point just before ABS intervention.  Once the car slows to 5mph, immediately accelerate back up to about 60mph, and brake again to roughly 5mph.  Repeat this series of stopping and accelerating 8 to 10 times.  Again, do not come to a complete stop with your foot on the brake pedal. Cool the brake system down by cruising at 45mph+ for 5 to 10 minutes. Visually inspect your discs.  They should be a blue/grey color (instead of shiny silver), and have an even layer of pad material across and around the entire rotor face. If the AP Racing rotors don’t have a layer of pad material on them, perform another series of stops in the manner outlined above.

Performance Friction PFC 410.34.0063.451/461 410mm Replacement Front Floating Racing Brake Rotors Fit The Following Cars which use PFC 410.069.63/64 (w/ OEM Iron Rotors or PCCB Rotors) - Center hat Excluded, rotor disc only. Replacement Disc Only For PFC 410.069.63/64 and 410.057.63/64 Porsche 992 GT3 PCCB/Iron (Front) Porsche 992 GT3RS PCCB/Iron (Front) Porsche 991 GT2RS PCCB (Front) Porsche 991 GT3 PCCB (Front) Porsche 991 GT3RS PCCB (Front) Porsche 718 / 982 GT4RS PCCB or Iron (Front) Porsche 718 GT4 PCCB (Front) PFC the manufacturer of Porsche Cup braking systems developed a 410mm front rotor replacement kit that is a direct replacement for the OEM 991 GT or 718 GT4 PCCB Brake rotors or OEM 718 / 982 GT4RS with PCCB or Iron rotors.  Performance Friction PFC V3 Discs with Zero Failure Technology Unique Rotor and Hat interface, eliminating most hardware. The elimination of hardware reduces weight, complexity, and installation time for less down time and more seat time on the track.  Replace your rotor discs in minutes with a flat head screwdriver PFC metallurgy specified for high Thermal stability and mechanical strength for increased longevity 48 vane geometry engineered for increased airflow for increased brake cooling during the heat of the battle while on track Patented slot pattern for increased initial bit and pad surface conditioning Lightweight forged hard anodized aluminum hat for increased durability and performance The two-piece PFC V3 design allows for disc-only replacement as well, minimizing future replacement costs and delivering outstanding performance. Sold/priced per pair.

Performance Friction PFC 390.32.0066.451/461 390mm Replacement Rear Floating Racing Brake Rotors Fit The Following Cars (w/ OEM PCCB Rotors)- Center hat Excluded, rotor disc only. Replacement Disc Only For PFC 390.075.63/64 Porsche 992 GT3 (Rear) Porsche 992 GT3RS (Rear) Porsche 718/982 GT4RS (Rear) Porsche 991 GT2RS/GT3/GT3RS (Rear) Porsche 981 GT4 (Rear) PFC the manufacturer of Porsche Cup braking systems developed a 390x32 mm rear rotor replacement kit that is a direct replacement for the OEM Steel Brake rotors.  Performance Friction PFC V3 Discs with Zero Failure Technology Unique Rotor and Hat interface, eliminating most hardware. The elimination of hardware reduces weight, complexity, and installation time for less down time and more seat time on the track.  Replace your rotor discs in minutes with a flat head screwdriver PFC metallurgy specified for high Thermal stability and mechanical strength for increased longevity 48 vane geometry engineered for increased airflow for increased brake cooling during the heat of the battle while on track Patented slot pattern for increased initial bit and pad surface conditioning Lightweight forged hard anodized aluminum hat for increased durability and performance The two-piece PFC V3 design allows for disc-only replacement as well, minimizing future replacement costs and delivering outstanding performance. PFC’s V3 discs are optimized to ensure the highest level of performance, wear and durability for your Porsche’s braking system.  These high-performance OEM replacement assemblies now feature aluminium hats in both front and rear, similar to the original. There is a saving of over one pound by trimming excess material from the unused areas around the disc in our new V3 ZeroFailures™ design, which will allow for disc changes in a matter of seconds with a flat head screwdriver. Sold/priced per pair.