981 Cayman GT4

Girodisc A1-066 Two Piece Floating Rotors FITS THE FOLLOWING CARS (OEM Steel Rotors): Porsche 981 Cayman GT4 Porsche 718 Cayman GT4 Porsche 991 Turbo/Turbo S Porsche 997 Turbo This Girodisc system upgrades the OEM front brakes to a 380mm two-piece steel disc and aluminum hat. This two-piece "floating rotor" design will bolt directly to your GT4 front and work flawlessly with the OEM calipers. Particularly when paired with the Girodisc A2-155 rear rotors, upgrading your brakes to lightweight, high-performance Girodisc rotors maintains the factory brake bias and ABS effectiveness. Much lighter than the OEM rotors, Girodisc rotors reduce rotational and unsprung mass giving you stronger braking and faster suspension response.Combined with Pagid or PFC racing brake pads and Competition Motorsport RF1 racing brake fluid, Girodisc rotors are the ultimate solution to overheated, cracked, warped OEM Porsche rotors that result from high-performance driving. The central hat of the rotor is made from 6061-T6 aircraft aluminum. The disc is manufactured in the USA from the same cast iron used by professional racing organizations. Its curved-vane design, developed in racing, acts like a centrifugal pump forcing cool air through the disc.The disc and hat mount together through a floating mount system using ten cadmium plated, high-strength alloy steel drive pins manufactured by Girodisc. These drive pins transfer braking load while maintaining axial and radial float between the disc and hat to allow for heat expansion. Anti-noise spring washers eliminate the noise typically associated with floating rotors. This two-piece Girodisc design allows for disc-only replacement, reusing the hat to minimize maintenance costs. Sold/priced per pair.

Girodisc A2-155 Two Piece Floating Racing Brake Rotors These Rotors Fit The Following Cars (w/ OEM Steel Rotors): Porsche 981 Cayman GT4 Rear Porsche 718 Cayman GT4 Rear Porsche 991 Turbo/Turbo S Rear This Girodisc system upgrades your Porsche OEM rear brakes to 380mm two-piece steel discs and aluminum hats. This two-piece floating rotor design will bolt directly to your Porsche GT4 or Turbo  and work flawlessly with the OEM calipers using the included machined aluminum spacers. Especially when paired with the Girodisc A1-066 front Porsche rotors , upgrading your brakes to lightweight, high-performance Girodisc rotors, you maintain the factory brake bias and ABS effectiveness. Much lighter than the OEM rotors, Girodisc rotors reduce rotational and unsprung mass giving you stronger braking and faster suspension response. Combined with Pagid or PFC racing brake pads and Competition Motorsport Performance RF1 racing brake fluid, Girodisc rotors are the ultimate solution to overheated, cracked OEM Porsche rotors that result from high-performance driving. The central hat of the rotor is made from 6061-T6 aircraft aluminum. The disc is manufactured in the USA from the same cast iron used by professional racing organizations. Its curved-vane design, developed in racing, acts like a centrifugal pump forcing cool air through the disc. The disc and hat mount together through a floating mount system using ten cadmium plated, high-strength alloy steel drive pins manufactured by Girodisc. These drive pins transfer braking load while maintaining axial and radial float between the disc and hat to allow for heat expansion. Anti-noise spring washers eliminate the noise typically associated with floating rotors.This two-piece Girodisc design allows for disc-only replacement, reusing the hat to minimize maintenance costs. Sold/priced per pair.

A1-156 Girodisc Two-Piece 410mm Front Brake Rotors FITMENT: Porsche 911 Carrera Turbo (991), Front Porsche Cayman GT4 (981), Front This Girodisc system is a 410mm two-piece steel rotor and aluminum hat combination, a direct-replacement upgrade for your car's OEM PCCB brakes1. The Girodisc A1-156 will bolt directly to your Porsche and work perfectly with your OEM calipers. There are two main reasons for replacing your PCCB: first, Girodisc rotors are designed to shed heat more effectively than the original rotors; second, the machined cast iron rotor rings are far more durable than the fragile PCCB rotors. This is critical when you're swapping wheels on-and-off the car for track days or racing. It's so easy to nick a carbon rotor and take a chunk out of it, rendering it useless. Pair these Girodisc rotors with Girodisc A2-156 rear rotors to maintain your factory brake bias and ABS efficiency. When used with Pagid or PFC performance brake pads, and CMS RF1 brake fluid, you have an excellent solution to easily cracked carbon-ceramic rotors. The central hat section of the Girodisc is made from 6061-T6 aircraft specification aluminum. The disc is manufactured from cast iron constructed in the USA, made to the same specification with the same material used by professional racing organizations. The rotors' curved vane design was developed in racing and acts as a centrifugal pump to force cooling air through the disc. The rotor and hat mount together through a floating mount system which utilizes ten high strength alloy steel drive pins manufactured by Girodisc in the USA to their own specifications and are cadmium plated for corrosion resistance. The alloy drive pins transfer the load from the brake action while maintaining the axial and radial float between the disc rotor and hat. The pins are secured by Grade-12 cap screws with hardened washers and mounted with anti-noise spring washers to allow for heat expansion while eliminating the rattle and noise associated with floating rotors. The two-piece Girodisc design allows for disc-only replacement as well, minimizing future replacement costs and delivering outstanding performance. Sold/priced per pair. 1 Note: you must use the same pad shape as that used on the Porsche 991/992 GT3/Turbo with factory iron rotors. The annulus (pad swept height) of these pads is smaller than that of the large PCCB pads.

PORSCHE 991 TURBO & 981 CAYMAN GT4 OEM PCCB This Girodisc system is a 390mm two-piece steel rotor and aluminum hat combination, a direct-replacement upgrade for the OEM PCCB brakes. The A2-156 will bolt directly to your Porsche and work perfectly with your OEM calipers. There are two main reasons for replacing your PCCB: first, the Girodisc rotors are designed to shed heat more effectively than the original rotors; second, the machined cast iron rotor rings are far more durable than the fragile OEM carbon-ceramic rotors. This is critical when you're swapping wheels on and off the car for track days or racing, because it's so easy to nick a carbon rotor and take a nice chunk out of it. When paired with the Girodisc A1-156 front rotors, your factory brake bias and ABS efficiency are maintained.  When used with Pagid or PFC performance brake pads, and Competition Motorsport RF1 brake fluid (also available from CompetitionMotorsport.com), you have an amazing solution to overheating, cracking and warping rotors. The central hat section of the disc is made from 6061-T6 aircraft specification aluminum.  The disc is manufactured from cast iron which is constructed in the USA and is made to the same specification with the same material used by professional racing organizations.  The rotors curved vane design was developed in racing and acts as a centrifugal pump to force cooling air through the disc.   The rotor and hat mount together through a floating mount system which utilizes eight to ten high strength alloy steel drive pins manufactured by Girodisc in the USA to our own specifications and are cadmium plated for corrosion resistance.  The alloy drive pins transfer the load from the brake action while maintaining the axial and radial float between the disc rotor and hat.  The pins are secured by Grade 12 cap screws with hardened washers and mounted with anti-noise spring washers to allow for heat expansion while eliminating the rattle and noise associated with floating rotors. The two-piece Girodisc design allows for rotor only replacement as well to minimize future replacement costs and deliver outstanding performance and cooling. Sold/priced per pair.

CMS Performance RF1 DOT4 Racing Brake Fluid Real-Life High Boiling Point Without The Real High Price RF1 Racing Brake Fluid from CMS Performance is a fully-synthetic DOT4 brake fluid formulated to provide extraordinary performance under the most demanding high-temperature racing and track-day conditions. With a dry boiling point of 328º C (622º F), RF1 exceeds all DOT3 & DOT4 requirements and is compatible with all DOT 3, 4, and 5.1 fluids. (Not compatible with DOT5 or mineral-based brake fluids.) On the race track, brake systems operate at very high sustained temperatures, and there is perhaps no single safety system more important in racing than your brakes. No single part of that system is more critical than brake fluid. At CMS Performance, we got tired of (and a little nervous) using "racing" brake fluid at the race track that didn't live up to its claimed performance when things got hot. So we did something about it. Manufactured in partnership with Orthene, the brake fluid supplier to many teams in Formula 1, WEC, and other professional series, RF1 Racing Brake Fluid was formulated to maintain consistent viscosity, lubricity, and compressibility at the extreme system temperatures and line pressures found in racing and track days. The bottom line is this: you can spend more on brake fluid, but you can't buy higher-performance than RF1 Racing Brake Fluid. RF1 Racing Brake Fluid Details: Typical dry boiling point: 328º C (622º F) Typical wet boiling point: 204º C (399º F) Exceeds DOT3 & DOT4 standards Bottle size: 500 ml (16.9 fl oz) Click Here for Product MSDS Sheet A Word About Flushing Brake Fluid All brake fluid degrades over time (not mileage), attracting water as it ages, which, at high brake temperatures, can lead to fluid boil and brake fade or failure. That's why the "wet" (aged) boiling point of any brake fluid is substantially lower than the "dry" (new) boiling point. To maintain maximum braking performance, Competition Motorsport strongly suggests replacing your brake fluid before every track event, but at least every three months if you're consistently racing and/or driving at track days. It's cheap insurance against learning about brake fade the hard way!

Pagid 4924 Racing Brake Pads Fits The Following Vehicles: Porsche 991 GT3 (2014-19), Front w/ iron brakes Porsche 991 GT3RS (2016-19), Front w/ iron brakes Porsche 991 Turbo (2013-19), Front w/ iron brakes Porsche 981/718 Cayman GT4 (2016+), Front w/ iron brakes Porsche 718 Cayman GT4RS (2021+), Front w/ iron brakes Pagid RSL 29: Pagid RSL 29 (Yellow) is the world-leading endurance brake pad used by most of the winning teams in motorsport. Although designed primarily for endurance racing, many competitors use this material successfully for sprint and short distance races also. RS29 has also found favor in the growing track day market due to the level of control, good cold performance, long life and low disc wear. Pagid RSL 1: Pagid RSL 1 has a high ceramic content with superior thermal insulation and higher heat resistance than metallic pad compounds. They feature excellent pad wear under endurance conditions, excellent rotor life, and are less aggressive than RST pads with excellent brake balance and modulation. Pagid RST 1: Pagid RST 1 is a high-friction, aggressive pad with instant pedal response, quick release, a firm pedal at all temperatures, and a progressive torque curve. Suitable for applications with high down-force and/or very high grip. RST 1 has a very high friction level and high temperature resistance. It is a semi-metallic resin bonded material containing steel fibers. Cold friction and initial bite makes this material most appropriate for Rally and NASCAR applications. Pagid RST 3: Pagid RST 3 is a medium-high friction metal-ceramic compound containing steel fibers and is therefore the perfect complement of the RST product family. RST 3 is exceptional in its low heat conductivity. Ideal for rally tarmac and gravel, GT cars, Touring Cars, prototype circuit racing, formula cars and club racing. It has a wide range of applications due to its combination of bite, friction and controllability.

Pagid Racing Brake Pads No. 4925 Fits The Following Cars: Porsche 918 Spyder (2013+), Rear Porsche 991 GT3 (2013+), Rear Porsche 991 GT3RS (2015+), Rear Porsche 991 Turbo (2013+), Rear Porsche Cayman GT4 (2016+), Rear Porsche Cayman GT4RS (2021+), Rear Pagid RSL 29: RSL 29 (known through the racing world as "Pagid Yellow") is the world-leading endurance brake pad used by most of the winning teams in motorsport. Although designed primarily for endurance racing, many competitors use this material successfully for sprint and short distance races also. Pagid RSL 29 has also found favor in the growing track day market due to the level of control, good cold performance, long life and low disc wear. Pagid RSC 1: RSC 1 is a good street/track compromise for enthusiasts with Carbon-Ceramic Brakes. Used for sprint racing and track days with all known types of ceramic brake discs. RSC 1 is an ideal combination of cold friction, fade resistance, and low thermal oxidation of the disc surface. The compound is a low metallic resin bonded material containing steel and aramid fibers. This material features good all-round characteristics and is suitable for all types of usage. Pagid RSL 1: Used in GT cars, Touring cars and prototype endurance racing. Due to the high friction and good modulation, often used in sprint races as well. Low-metallic resin bonded materials containing steel and aramid fibers with very high heat resistance. RSL 1 maintains a constant friction level over a wide range of temperatures. Its reduced wear rate and disc friendliness make RSL 1 appropriate for endurance races. Pagid RST 3: RST 3 is a medium-high friction metal-ceramic compound containing steel fibers. It is known for its combination of bite, friction and controllability. RST 3 sees a wide range of applications: rally tarmac and gravel, GT cars, Touring cars and prototype circuit racing, formula cars and club racing.

Pagid Racing Brake Pads No. 4927 Fits These Vehicles: Porsche 918 Spyder (2013+), Front w/ PCCB Porsche 991 GT3, Front w/ PCCB Porsche 991 GT3RS, Front w/ PCCB Porsche 991 Turbo, Front w/ PCCB Porsche 981/718 GT4, Front w/ PCCB Porsche 718 GT4RS, Front w/ PCCB Pagid RSC 1: The Pagid RSC1 is a good street/track compromise for enthusiasts with Carbon-Ceramic Brakes. Used for sprint racing and track days compound with all known types of ceramic brake discs. An ideal combination of cold friction, fade resistance and low thermal oxidation of the disc surface.

PFC Brake Pads 1773.xx.17.44 This is an updated PFC part number. The previous part number was 7721.xx.17.44. FITMENT (Iron Rotors Only): Porsche 991 GT3/GT3RS (2014-19), Front Porsche 991 Turbo/Turbo S (2013-19), Front Porsche 991.2 3.0 Carrera GTS (2017-19), Front Porsche 991.2 3.0 Carrera S (2015-19), Front Porsche 992 3.0 Carrera S & 4S (2020+), Front Porsche 992 GT3 (2022+), Front Porsche 992 Speedster (2019-22), Front Porsche 981 Cayman GT4 (2015-19), Front Porsche 718 Cayman GT4 (2020+), Front PFC Brakes offers a wide range of sports car applications. Each PFC product is meticulously created to the highest performance and technology expectations. The folks at PFC take pride in the accomplishments of the drivers and race teams that run PFC products. With More Championships than Any Other™, PFC are among the best racing brakes on the market. Known around the globe in the sports car market, PFC is involved with numerous sports car events including: IMSA Continental Tire Sports Car Challenge Porsche Cup Racing Pirelli World Challenge With over 35 years of friction knowledge and on-track experience, PFC's process enables them to provide you with the proper friction every time. NO COMPROMISES All PFC pad compounds have been thoroughly processed and are “race ready”. That means very easy burnishing to bed pads and rotors. PFC 331 Compound PFC 331 is the next generation of PFC endurance material, giving you improved control with ABS while being gentle on rotors. The 331 Carbon Metallic compound has been developed with higher initial bite than PFC’s renowned 08 endurance compound. The 331 has improved release while continuing to offer exceptional control and feel. It boasts a low wear rate and exceptional disc conditioning. PFC 13 Compound The PFC 13 is the new generation of ultimate high bite/high friction performance. Performance Friction's 13 compound has been developed with increased bite, excellent modulation, and superior disc conditioning and release characteristics for exceptional control. Ultra-smooth and great for tracks with high grip or high downforce cars. It is the ultimate combination of high bite and infinite control. Ideal where high bite in the first one-third of the stop is desired. PFC 13 exhibits wear on a par with PFC’s legendary 01 compound, but will operate at higher temperatures if called on. PFC 13 has a very high threshold for fade resistance. Out of all the high bite/high torque pads on the market, PFC 13 has been shown to have some of the lowest taper wear in a properly designed race caliper. PFC 11 Compound A new generation sprint and medium-distance friction compound, PFC 11 gives you the ultimate in control alongside superior disc conditioning. Developed from the famed PFC 01 compound with improved bite, modulation, and release characteristics. The PFC 11 is ultra-smooth, developed to reduce wheel lock-up at the end of braking while giving you more cold- and hot-bite than the more endurance-oriented PFC 08 compound.

PFC Brake Pads 7727.xx.18.44 PFC Brakes offers a wide range of sports car applications. Each PFC product is meticulously created to the highest performance and technology expectations. The folks at PFC take pride in the accomplishments of the drivers and race teams that run PFC products. With More Championships than Any Other™, PFC are among the best racing brakes on the market. Known around the globe in the sports car market, PFC is involved with numerous sports car events including: IMSA Continental Tire Sports Car Challenge Porsche Cup Racing Pirelli World Challenge With over 35 years of friction knowledge and on-track experience, PFC's process enables them to provide you with the proper friction every time. NO COMPROMISES All PFC pad compounds have been thoroughly processed and are “race ready”. That means very easy burnishing to bed pads and rotors. PFC 332 Compound PFC 332 has been formulated with lower bite and torque for rear brake applications. With a smooth release, the PFC 332 compound offers excellent stability and control. PFC 332 has been designed to work with ABS applications and has exceptionally low wear rates. PFC 11 Compound A new generation sprint and medium-distance friction compound, PFC 11 gives you the ultimate in control alongside superior disc conditioning. Developed from the famed PFC 01 compound with improved bite, modulation, and release characteristics. The PFC 11 is ultra-smooth, developed to reduce wheel lock-up at the end of braking while giving you more cold- and hot-bite than the more endurance-oriented PFC 08 compound. FITMENT (Iron Rotors Only): Porsche 991 GT3RS 2016-2019 Rear Porsche 991 GT3 2014-2019 Rear Porsche 991 Speedster 2019-2021 Rear Porsche 991 Turbo/Turbo S 2013-2019 Rear Porsche 992 GT3 2022- Rear Porsche 992 Turbo 2019- Rear Porsche 918 Spyder 2013-2016 Rear Porsche 981 Cayman GT4 2015-2019 Rear Porsche 718 Cayman GT4 2019- Rear

Girodisc Brake Pad Spreader This indispensable tool is used by race teams, shops, and enthusiasts alike who have high performance four- and six-piston calipers. The Girodisc Brake Pad Spreader is designed to easily spread brake pads and pistons to facilitate quick replacement of pads and/or rotors in a shop or racing environment. No more screwdrivers, pliers, hammers, or C-clamps! This tool will retract the pistons fully and evenly into their bores with one squeeze of the levers. The Girodisc Brake Pad Spreader was designed to be used with popular racing brake calipers from Brembo, AP Racing, Alcon, and other performance calipers in racing and road use. To help it fit into any caliper, the amount of throw is adjustable. Insert the spreading plates one way for wider six-piston calipers, then turn the spreader 90o and use the plate sides for four-piston calipers. The Girodisc Brake Pad Spreader is made from heavy-gauge steel, powder-coated for durability. The slider is cadmium-plated, and nylon pivot bushings ensure smooth action. The Girodisc Brake Pad Spreader will quickly become an invaluable tool for any race team, shop, or enthusiast who changes pads and rotors frequently.

Girodisc Titanium Brake Pad Shields FITMENTS: Porsche 991, 992, GT4 (Front) The problem of brake fluid boiling is caused by braking heat transferring from the rotors and pads directly into the fluid through the caliper pistons. When brake fluid boils, it releases air that is normally part of the molecular structure of the fluid. This air is compressible, of course, so brake pedal pressure compresses this air instead of pushing brake fluid and moving the caliper pistons. The brake pedal goes to the floor. Production street cars tend to suffer from this on track days because they don't have the extensive cooling ducts and exotic brake materials found on race cars. Race-only brake calipers generally come with titanium caliper pistons for one reason: titanium has very low thermal conductivity, which means it's bad at transferring heat. That's good if you're trying to keep your brake fluid from boiling. Here's a comparison of materials and their relative thermal conductivity ratings in Watts per meter-Kelvin (lower is better): Titanium 6AL-4V = 6.7 W/mK Steel = 52 W/mK Aluminum = 130 W/mK Most fixed calipers use aluminum pistons which are, unfortunately, excellent at transferring braking heat to your brake fluid. Our solution is to place Girodisc's thin titanium shims between each brake pad and the caliper pistons. This helps prevent braking heat from transferring into the pistons and, thus, into the fluid. For cars that are going to see hard driving or multiple track days, these shims are affordable protection against losing your brake pedal at the worst possible time, making your track day very expensive. Water-jet cut to exact size, so there's no cutting, grinding, or swearing involved. Price is per axle (four shims)

Girodisc Titanium Brake Pad Shields FITS: Porsche 991, 992, GT4 Rear The problem of brake fluid boiling is due to heat transferring from the rotors and pads directly into the fluid through the caliper pistons. When brake fluid boils, it releases air that is normally part of the molecular structure of the fluid. This air is compressible, of course, and the brake pedal goes to the floor instead of moving the caliper pistons. Production cars tend to suffer from this on track days because they don't have the extensive cooling ducts and exotic brake materials found on race cars. Race-only brake calipers generally come with titanium caliper pistons for one reason: titanium has low thermal conductivity. This means it's very bad at transferring heat, which is good if you're trying to keep your brake fluid from boiling. Here's a comparison of materials and their relative thermal conductivity ratings (lower is better):   Titanium 6AL-4V = 6.7 W/mk Steel = 52 W/mk Aluminum = 130 W/mk   Most fixed calipers use aluminum pistons which are, unfortunately, excellent at transferring braking heat to your brake fluid. Our solution is to place Girodisc's thin titanium shims between the brake pad and the caliper pistons. This helps prevent braking heat from transferring into the pistons and, thus, into the fluid.  For cars that are going to see hard or multiple track days, these shims are affordable protection from losing your brake pedal at the wrong time and making your track day very expensive. Water jet cut to exact size; no cutting, grinding, or swearing involved. Price is per axle (four shims)

A1-266 Girodisc Two-Piece 380mm Front Brake Rotors FITMENT: Porsche Cayman GT4 Clubsport, Front This Girodisc system is a 380mm two-piece steel rotor and aluminum hat combination, a direct-replacement upgrade for the one-piece OEM Cayman GT4 Clubsport steel brakes. The Girodisc A1-266 will bolt directly to your Porsche GT4 Clubsport and will work perfectly with your OEM calipers. There are two main reasons for replacing your OEM rotors: first, the Girodisc rotors are designed to shed heat more effectively than the original rotors; second, the slotted Girodisc A1-266 will far outlast the OEM drilled rotors. When subjected to intense heat in a racing or track-day environment, the drilled holes in the OEM rotors form cracks which can lead to rotor failure. When paired with the Girodisc A2-266 rear rotors, your factory brake bias and ABS efficiency are maintained. When used with Pagid or PFC performance brake pads and CMS RF-1 brake fluid (available from Competition Motorsport), you have an amazing solution to overheating, cracking and warping rotors. The central hat section of each Girodisc is made from 6061-T6 aircraft specification aluminum. The disc is manufactured from cast iron constructed in the USA, made to the same specification with the same material used by professional racing organizations. The rotors' curved vane design was developed in racing and acts as a centrifugal pump to force cooling air through the disc. The rotor and hat mount together through a floating mount system which utilizes ten high strength alloy steel drive pins manufactured by Girodisc in the USA to their own specifications and are cadmium plated for corrosion resistance. The alloy drive pins transfer the load from the brake action while maintaining the axial and radial float between the disc rotor and hat. The pins are secured by class 12.9 cap screws with hardened washers and mounted with anti-noise spring washers to allow for heat expansion while eliminating the rattle and noise associated with floating rotors. The two-piece Girodisc design allows for disc-only replacement as well, minimizing future replacement costs and delivering outstanding performance. Sold/priced per pair.

This Girodisc system is a 380mm two-piece steel rotor and aluminum hat combination, a direct-replacement upgrade for the one-piece OEM GT4 Clubsport steel brakes. The A2-266 will bolt directly to the GT4 ClubSport and work perfectly with your OEM calipers. There are two main reasons for replacing your OEM rotors: first, the Girodisc rotors are designed to shed heat more effectively than the original rotors; second, the slotted Girodisc A2-266 will far outlast the OEM drilled rotors. When subjected to intense heat in a racing or track-day environment, the drilled holes in the OEM rotors originate cracks which can lead to rotor failure. When paired with the Girodisc A1-266 front rotors, your factory brake bias and ABS efficiency are maintained. When used with Pagid or PFC performance brake pads, and Competition Motorsport RF1 brake fluid (also available from CompetitionMotorsport.com), you have an amazing solution to overheating, cracking and warping rotors. The central hat section of the disc is made from 6061-T6 aircraft specification aluminum.  The disc is manufactured from cast iron which is constructed in the USA and is made to the same specification with the same material used by professional racing organizations.  The rotors curved vane design was developed in racing and acts as a centrifugal pump to force cooling air through the disc.   The rotor and hat mount together through a floating mount system which utilizes eight to ten high strength alloy steel drive pins manufactured by Girodisc in the USA to our own specifications and are cadmium plated for corrosion resistance.  The alloy drive pins transfer the load from the brake action while maintaining the axial and radial float between the disc rotor and hat.  The pins are secured by Grade 12 cap screws with hardened washers and mounted with anti-noise spring washers to allow for heat expansion while eliminating the rattle and noise associated with floating rotors. The two-piece Girodisc design allows for rotor only replacement as well to minimize future replacement costs and deliver outstanding performance and cooling. Sold/priced per pair.

Race Technologies RE10 Front Brake Pad - 2450.18.RE10 FITMENTS: Porsche 991.2 GT3, GT3RS, and GT2RS, Front w/ iron rotors Porsche 991 Turbo/Turbo S, Front w/ iron rotors Porsche 981/718 Cayman GT4, Front w/ iron rotors Race Technologies RE10 is the ultimate endurance race compound, offering a balance of excellent stopping power, low thermal conductivity, and extremely low pad and rotor wear. Utilizing the latest friction material technology, RE10 offers consistent performance under the most demanding of environments. Typical Applications: Professional Endurance Racing, Club Racing, and HPDE on high demand brake platforms. Note: RE10 is a "racing use only" pad. Running a "racing use only" pad on the street could produce excessive noise and dust. Disc wear could be accelerated if driven at cold temperatures or used in the incorrect temperature range. Racing pads are designed to work in specific temperature ranges, so it's important to choose the right compound for the environment the vehicle will be used in. Pad compounds are run on a brake dynamometer over multiple brake applications ("stops") to test the materials in a controlled environment and obtain accurate data. Wear rates and operating temperatures can be influenced by car set-up, grip levels, track layout, and other variables.