Carbon Fiber Helmets

Stilo Venti WRC ZERO 8860-2018 Carbon Fiber Helmet Uncompromising Safety and Performance Stilo Venti WRC ZERO 8860-2018 Carbon Fiber Helmet The Stilo Venti WRC ZERO 8860-2018 Carbon Fiber Helmet is engineered for professional rally drivers and co-drivers who demand elite protection, exceptionally low weight, and clear in-car communication. Combining an advanced carbon fiber shell with Stilo’s weight-saving PURO technology, integrated WRC electronics, and FIA 8860-2018 certification, this open-face rally helmet is built for the most demanding stages in motorsport. The Venti WRC ZERO is the premium, weight-focused version of Stilo’s championship-winning Venti rally helmet. Its compact shell, noise-attenuating earmuffs, adjustable microphone, and recessed communication connection create a complete helmet and intercom platform designed around the needs of a rally crew. FIA 8860-2018 Protection for Elite Competition The Stilo Venti WRC ZERO is certified to the FIA 8860-2018 advanced helmet standard. Developed for high-level motorsport, this certification subjects the helmet to demanding impact, penetration, flame-resistance, and structural performance requirements. Its high-tensile carbon fiber shell delivers exceptional strength without the unnecessary bulk associated with heavier helmet constructions. Factory-fitted HANS post anchors allow the helmet to be connected to a compatible frontal head restraint without requiring separate anchor installation. Ultra-Light ZERO Carbon Construction Every part of the Venti WRC ZERO is designed with weight reduction in mind. Stilo’s PURO carbon technology eliminates the need for a conventional final clear-coat layer, reducing unnecessary material while revealing the helmet’s distinctive raw carbon fiber finish. The result is the lightest helmet configuration in the Venti WRC range, with a listed weight of approximately 2.6 pounds, depending on helmet size and equipment configuration. Reducing weight at the driver’s head can help limit neck fatigue during long rally stages, endurance events, and repeated high-load driving conditions. Stilo uses three shell sizes across the Venti WRC range so each helmet can maintain a more compact and proportional exterior profile. This approach helps prevent smaller sizes from being placed inside an unnecessarily large or heavy shell. Integrated Stilo WRC Communication System The Venti WRC ZERO is designed around Stilo’s integrated WRC intercom system. Noise-attenuating earmuffs surround the built-in speakers, helping isolate the driver or co-driver from engine, drivetrain, gravel, and cabin noise. An adjustable magnetic dynamic noise-canceling microphone is mounted on a reshaped boom designed to improve voice clarity. The microphone position can be adjusted closer to or farther from the mouth to achieve clearer communication while reducing unwanted ambient sound. This integrated design eliminates the need to install a separate headset inside the helmet, creating a cleaner fit and reducing interference between the communication equipment, helmet padding, and the wearer’s ears. Wireless and Hard-Wired Intercom Compatibility The helmet’s recessed side communication port is shaped to accept the Stilo WL wireless key, sold separately. Once installed, the wireless key follows the contour of the shell to help prevent interference with FHR straps and helmet hardware. The integrated electronics are also compatible with traditional hard-wired Stilo DG and WRC-series amplifiers. This allows a competitor to use the same helmet in vehicles equipped with either Stilo wireless or conventional wired communication systems. Driver-Focused Visibility and Ventilation The redesigned shell and adjustable peak provide the visibility needed for constantly changing rally conditions. The peak can be raised or lowered to help manage low-angle sunlight, glare, and changing terrain without obstructing the driver’s forward view. The Venti WRC ZERO is also compatible with Stilo short visors, sold separately, for competitors who want additional eye protection. Integrated top ventilation openings help reduce heat and moisture buildup and allow the helmet to be used with a compatible Stilo Top Air system. Comfort for Long Rally Stages Updated interior padding works with the helmet’s soft noise-attenuating earmuffs to create a secure and comfortable fit. Expanded-polystyrene cheek protection supports the sides of the face while preserving the acoustic isolation required for clear communication. The combination of reduced shell weight, improved padding, sound insulation, and integrated electronics makes the Venti WRC ZERO especially well suited to drivers and co-drivers who remain helmeted for extended periods. Stilo Venti WRC ZERO Helmet Features FIA 8860-2018 certified open-face motorsport helmet High-tensile carbon fiber shell Stilo ZERO construction focused on minimum weight PURO carbon technology eliminates the conventional final clear coat Approximate listed weight of 2.6 pounds, depending on size and configuration Three-shell-size construction for a compact, proportional fit Integrated Stilo WRC communication electronics Built-in speakers with noise-attenuating earmuffs Adjustable magnetic dynamic noise-canceling microphone Reshaped microphone boom designed to improve voice clarity Recessed side communication port for a streamlined connection Compatible with the Stilo WL wireless key, sold separately Compatible with hard-wired Stilo DG and WRC-series amplifiers Adjustable rally peak for changing light conditions Compatible with optional Stilo short visors Top ventilation openings help reduce heat and moisture Compatible with a Stilo Top Air system Updated interior comfort padding Factory-fitted HANS post anchors Designed, developed, tested, and manufactured in Italy Signature required upon delivery A Championship-Proven Rally Platform The Venti platform represents the modern evolution of Stilo’s open-face rally helmet program. Its combination of integrated communication, advanced carbon construction, ergonomic fit, and professional-level protection has made it a trusted choice among championship-winning rally crews. For competitors who prioritize every gram of equipment weight without sacrificing communication quality or FIA 8860 protection, the Stilo Venti WRC ZERO is the flagship choice within the Venti WRC range. How to Measure for a Stilo Helmet Use a soft measuring tape to measure around the largest circumference of your head. Position the tape approximately one inch above your eyebrows, pass it above your ears, and wrap it around the widest point at the back of your head. Take the measurement two or three times and use the largest result. Compare the measurement in centimeters with the Stilo sizing chart. The helmet should feel evenly snug around the entire head without creating sharp or painful pressure points. With the chin strap secured, the helmet should not rotate independently when moved from side to side. New helmet padding may relax slightly as it conforms to the wearer, so a new helmet should not begin with a loose fit. Stilo Venti WRC Sizing Chart Questions About the Stilo Venti WRC ZERO 8860-2018 Helmet Is the Stilo Venti WRC ZERO certified to FIA 8860-2018?Yes. The helmet is certified to the FIA 8860-2018 advanced helmet standard. Competitors should still confirm the exact helmet requirements and accepted certification dates in their series rulebook before ordering. What is the difference between the Venti WRC ZERO and the standard Venti WRC Carbon?The ZERO is the range-topping, weight-focused configuration. It uses Stilo’s PURO carbon technology and eliminates the conventional final clear-coat layer to achieve the lowest possible weight while meeting FIA 8860-2018 requirements. How much does the Venti WRC ZERO weigh?The listed weight is approximately 2.6 pounds. Actual weight can vary with helmet size, production tolerances, and installed communication equipment. Does the helmet include an intercom system?Yes. It includes Stilo WRC communication electronics with integrated speakers, noise-attenuating earmuffs, and an adjustable magnetic dynamic noise-canceling microphone. Does the helmet include the Stilo WL wireless key?No. The helmet is designed to accept the Stilo WL wireless key, but the wireless key and compatible amplifier are sold separately. Can the helmet be connected to a wired Stilo amplifier?Yes. The communication system remains compatible with hard-wired Stilo DG and WRC-series amplifiers, allowing the helmet to be used in vehicles without a wireless system. Does the Venti WRC ZERO include HANS anchors?Yes. Factory-fitted HANS post anchors are supplied with the helmet for connection to a compatible frontal head restraint. Does the helmet have a visor?The helmet uses an adjustable rally peak. It is also compatible with optional Stilo short visors, which are sold separately. Is the microphone position adjustable?Yes. The microphone position can be adjusted to help establish the correct distance from the wearer’s mouth for improved voice clarity and reduced ambient noise. Why does the carbon shell have a raw appearance?The raw carbon appearance is a result of Stilo’s PURO technology. The final clear-coat layer is eliminated to reduce weight and expose the natural carbon fiber construction. Is a signature required when this helmet is delivered?Yes. Due to the value of this professional motorsport helmet, a signature is required upon delivery. ```

Stilo ST6 ZERO FN ABP Carbon Fiber 8860-2018 Racing Helmet  The Legendary Stilo ZERO Carbon Helmet - Forever Ahead For over 25 years Stilo has lead the way in racing helmet innovation, and the new ST6 line marks a bold new chapter. With input from Porsche and F1 teams, Stilo developed enhanced front and top aerodynamics to deliver exceptional performance from the new Stilo ST6 line of helmets. Developed with the world's top drivers from Formula One and endurance racing, the ST6 reflects real-world needs at ever level of auto racing. The ST6 carbon fiber helmet is one of the lightest helmets on the market. Featuring enhanced airflow, visibility, and comfort while maintaining market-leading safety standards. Developed with input from the Aston martin F1 team, ever feature of the ST6 including the track-tested aerodynamics and a cutting edge dual lock visor system, its designed to give racers a performance edge. The Brand New Stilo ST6 helmet improves on the market-leading Stilo ST5 in every way including; 10% Lighter than Stilo ST5 26% More Airflow than Stilo ST5 11% More Visibility More Comfortable Liner and Cheek pads More Shell Sizes for Lower Weight Better Visor Construction for Durability and Ease of Care Higher Quality Visor Hardware for Increased Reliability Stilo ST6 FN Zero ABP Auto Racing Helmet Features Puro Tech: Stilo's proprietary carbon fiber manufacturing process eliminates the need for extra lacquers or additional coatings, minimizing the weight of your new helmet. With the Puro process, Stilo delivers the lightest and safest helmet on the market. New Shell Size Options: Now offered in four shell sizes, the Stilo ST6 ZERO FN ABP auto racing helmet allows you to receive the lightest and smallest shell size possible for your head shape. Increased Airflow Design: by utilizing our key partnerships with Formula One teams we have redesigned our front ventilation to increase airflow while maximizing safety. The new Stilo ST6 also comes standard with ventilation holes in the top channeling airflow through the EPS foam to reduce sweat and moisture to keep you performing at your best. Increased Downward Visibility: with input from professional drivers around the globe, Stilo has increased the downward Field of view of the Stilo ST6 carbon fiber helmet creating a wider field of vision for greater awareness on the track. Interior Comfort: New and improved, the Stilo ST6 carbon fiber helmet cheek padding is redesigned to enhance stability and increase comfort.   Injection Molded Visor: brand new high performance visors provide exceptional vision and are coated in a new high performance washable anti-fog treatment. Dual Visor Lock: pioneering the industry, this dual visor lock complies with FIA standards both in fully closed and ventilation positions. Updated Visor Hardware: designed for easy installation and smoother activation, this visor hardware can be purchased in a variety of anodized finishes. Stilo ST6 ZERO FN ABP Carbon Fiber Auto Racing Helmet Sizing Note We have found that customers who typically wear a size 59 in other brands are most comfortable in a Stilo size 60, which uses the large shell. Please order accordingly. Stilo ST6 ZERO FN ABP 8860-2018 Carbon Fiber Helmet Details Manufacturer: Stilo Helmets Manufacturer part number: AA0810AG3S Homologation: FIA 8860-2018 ABP Compatible shields: Stilo ST6 ABP helmet shields Noise-attenuating earmuffs included Other Versions of the Stilo ST6 Racing Helmet Stilo ST6 GT SA2020 Carbon Fiber Helmet Stilo Helmet ST6 FN 8859-ABP Helmet Stilo ST6 FN Zero 8860-2018 Carbon Fiber Helmet Stilo ST6 FN ABP 8860-2018 Carbon Fiber Helmet Stilo ST6 GT Composite Helmet Stilo ST6 FN 8859-ABP Helmet Stilo ST6 GT 8860 Carbon Fiber Helmet Stilo ST6 FN 8860 Carbon Fiber Helmet Stilo ST6 FN Carbon Fiber Helmet Stilo ST6 GT ZERO 8860-2018 Carbon Fiber Helmet Measuring Your Head For Your New Stilo ST6 ZERO FN ABP 8860-2018 Carbon Fiber Helmet The most effective helmet is one that fits properly. To measure your head, have an assistant use a dressmaker's tape or a piece of string to measure the circumference of your head. Start at a point about an inch above your eyebrows, looping around the back of your head at the point that results in the largest measurement, and finally around to the front again. It's a good idea to take two or three measurements to make sure you have the largest one. This helmet will ship with signature required for delivery.  

Schuberth SF4 8860-2018 Carbon Fiber Helmet (Non-ABP) The Schuberth SF4 8860-2018 Carbon Fiber Helmet brings Formula-level materials, protection, and visor technology to professional GT, prototype, endurance, and open-cockpit drivers who do not require an ABP-homologated helmet. Handcrafted at Schuberth’s motorsport production facility in Italy, the SF4 combines an autoclave-cured carbon fiber shell with advanced ventilation, a Formula-derived injected visor, a two-stage visor lock, and extensive accessory compatibility. Its compact construction and refined interior are designed to support drivers through long race stints without compromising the advanced protection required by the FIA 8860-2018 standard. FIA 8860-2018 Advanced Helmet Protection The Schuberth SF4 is homologated to the FIA 8860-2018 advanced helmet standard under FIA homologation number AH.020.21-C. This is a professional-level motorsport helmet standard developed for demanding international competition. This specific SF4 is the non-ABP version. It does not incorporate the reduced eyeport and extended upper visor-area protection found on the SF4 ABP. That distinction makes the standard SF4 particularly well suited to GT cars, prototypes, endurance vehicles, and open-cockpit applications in which the governing series does not require Advanced Ballistic Protection homologation. Drivers should always verify the required helmet certification with their sanctioning body, race series, or event organizer before purchasing. Handcrafted Autoclave-Cured Carbon Fiber Shell Each Schuberth SF4 begins with a lightweight, hand-laid carbon fiber shell that is cured inside an autoclave. This specialized manufacturing process uses controlled heat and pressure to consolidate the carbon layers and create a strong, consistent helmet structure. The shell is handcrafted at Schuberth’s dedicated motorsport facility in Italy using production techniques developed through more than two decades of Formula racing experience. The result is a compact carbon helmet that balances structural strength, low weight, aerodynamic efficiency, and Schuberth’s unmistakable motorsport profile. Built for Long GT and Prototype Racing Stints The SF4 was developed for drivers who may remain helmeted for extended periods during endurance, GT, and prototype competition. Its compact shell profile, balanced construction, comfortable interior, and controlled airflow help reduce distractions during long sessions. The interior is shaped to maintain stable contact around the driver’s head and face without relying on excessive pressure. Multiple shell and interior configurations help Schuberth provide a more proportional fit across the helmet’s available size range. Because head shape and padding preference can affect fit, drivers should use the Schuberth sizing chart as a starting point and try the helmet on whenever possible. Formula-Derived Ventilation System Air channels integrated into the helmet’s EPS liner distribute fresh air through the interior while directing warm air away from the driver’s head. Schuberth states that, in unrestricted airflow, the system can provide up to 14 liters of fresh air per second at 100 km/h. The SF4 can be configured with optional ventilation accessories to suit different cockpit designs and airflow conditions. Available configurations may include individual ventilation scoops, top-air systems, chin ventilation components, and aerodynamic accessories. This flexibility allows the helmet to be adapted for enclosed GT cockpits, forced-air systems, prototypes, and open-cockpit vehicles. Injected Visor with Optical Clarity The Schuberth SF4 uses an injected visor developed from the brand’s Formula racing program. The manufacturing process is designed to minimize the optical distortion that can occur through the curved viewing area of a conventional racing shield. Schuberth offers multiple compatible visor options ranging from clear and dark tint to mirrored and multi-layer mirrored finishes. This allows drivers to select a visor suited to daytime, nighttime, bright-sun, or changing-weather competition. Standard SF4 visors are supplied with tear-off posts, allowing compatible tear-offs to be installed for events where dirt, rubber, oil, or debris may collect on the visor surface. Pinlock 120 Anti-Fog Performance Standard Schuberth SF4 visors are equipped with a Pinlock 120 anti-fog lens. The insert creates an insulating air pocket between the visor and the lens, helping reduce condensation when cockpit temperature, humidity, or weather conditions change. This system is especially valuable during endurance racing, wet events, cool-weather competition, and driver changes where moisture can quickly affect visibility. The Pinlock lens and visor should be cleaned only with appropriate materials and techniques to avoid damaging their optical or anti-fog surfaces. Central Two-Stage Visor Lock The SF4’s central visor mechanism is designed to close the visor evenly on both sides of the helmet. This symmetrical closure helps create consistent engagement with the eyeport seal and provides dependable visor operation while the driver is wearing racing gloves. The lock provides two functional positions: Stage One: Keeps the visor securely locked while allowing a small amount of ventilation into the helmet. Stage Two: Pulls the visor into a firmer seal to help block fine dust and water. The ventilation position allows the driver to increase airflow without leaving the visor unsecured. The fully sealed position is intended for conditions where dust, spray, or moisture protection takes priority. Communication-System Ready The Schuberth SF4 can be configured with optional integrated communication electronics. This allows the driver to build a professional radio setup suited to the team’s amplifier, connector, microphone, and audio requirements. Communication equipment is not included with the standard helmet unless it is specifically selected as part of the purchased configuration. Microphones, speakers, earphones, connectors, wiring, and related electronics may be sold separately. Any communication or earcup configuration must comply with the rules of the driver’s sanctioning body and race series. Customizable Aerodynamics and Airflow Different cars create different airflow patterns around the driver’s helmet. The SF4 platform can be adapted with compatible accessories to improve airflow, aerodynamic stability, cooling, and cockpit integration. Depending on the selected configuration, compatible Schuberth SF4 accessories may include: Top-air ventilation components Individual helmet ventilation scoops Chin ventilation scoops Rear and top aerodynamic spoilers Replacement clear, tinted, and mirrored visors Pinlock 120 anti-fog components Visor tear-offs Optional integrated communication electronics Replacement interior padding and fit components Accessory availability and compatibility can vary by helmet size, production version, and intended application. Non-ABP SF4 Versus the SF4 ABP The standard SF4 and SF4 ABP share Schuberth’s Formula-derived carbon construction and professional motorsport engineering, but they carry different FIA homologations. The non-ABP SF4 has a larger conventional eyeport and is intended for applications where FIA 8860-2018 certification is required but ABP homologation is not mandatory. The SF4 ABP uses an extended upper visor-area structure and reduced eyeport designed to satisfy Advanced Ballistic Protection requirements. An accessory visor strip or reinforcement panel does not convert the standard SF4 into an ABP-homologated helmet. The helmet remains certified only to the homologation stated on its FIA label. Schuberth SF4 Helmet Features FIA 8860-2018 advanced helmet homologation FIA homologation number AH.020.21-C Non-ABP full-face helmet configuration Designed for GT, prototype, endurance, and eligible open-cockpit competition Hand-laid carbon fiber shell Autoclave-cured carbon construction Compact and lightweight exterior profile Produced at Schuberth’s motorsport factory in Italy Engineering derived from Schuberth’s Formula racing program Air channels integrated into the EPS liner Up to 14 liters of fresh airflow per second at 100 km/h in unrestricted airflow Injected visor designed to reduce optical distortion Multiple clear, tinted, and mirrored visor options available Pinlock 120 anti-fog lens on standard visors Factory-installed tear-off posts Central two-stage visor locking system Locked ventilation position Firm sealed visor position for dust and water resistance Compatible with optional integrated communication electronics Compatible with multiple ventilation and aerodynamic accessories Schuberth helmet pouch included Schuberth SF4 Product Specifications Manufacturer: Schuberth Model: SF4 Helmet Type: Full-face auto racing helmet Homologation: FIA 8860-2018 FIA Homologation Number: AH.020.21-C ABP Homologated: No Shell Material: Autoclave-cured carbon fiber Visor: Formula-derived injected visor Anti-Fog System: Pinlock 120 on standard visors Tear-Off Posts: Included on standard visors Visor Lock: Central two-stage locking mechanism Communication Electronics: Optional and sold separately Included Accessory: Schuberth helmet pouch Manufacturing Location: Italy How to Measure for a Schuberth SF4 Helmet Use a soft measuring tape to measure around the widest circumference of your head. Position the tape approximately one inch above your eyebrows, pass it above the ears, and wrap it around the widest point at the back of your head. Keep the tape level and comfortably snug without pulling it tight. Take the measurement two or three times and use the largest result when reviewing the Schuberth SF4 sizing chart. A properly fitted racing helmet should create firm, even contact around the crown, sides, and cheeks. It should not create sharp or painful pressure points, and it should not rotate independently when the chin strap is properly secured. Schuberth Sizing Chart Schuberth SF4 Carbon Fiber Helmet Available Accessories Schuberth SF4 Top Air Available Here Schuberth SF4 Individual Vent Scoops Available Here Schuberth SF4 Visors Available here Schuberth SF4 Scoops avalible here Questions About the Schuberth SF4 Carbon Helmet Is the Schuberth SF4 certified to FIA 8860-2018?Yes. The non-ABP Schuberth SF4 is homologated to FIA 8860-2018 under FIA homologation number AH.020.21-C. Is this the ABP version of the Schuberth SF4?No. This listing is for the standard non-ABP SF4. It does not carry FIA 8860-2018-ABP homologation. Does non-ABP mean that the SF4 is not an advanced FIA helmet?No. The SF4 is still an FIA 8860-2018 advanced helmet. Non-ABP only means that it does not include the additional Advanced Ballistic Protection configuration required by certain racing series. What type of racing is the non-ABP SF4 designed for?It is designed primarily for GT, prototype, endurance, and open-cockpit racing applications where FIA 8860-2018 is accepted and ABP homologation is not mandatory. Can I use the SF4 in an open-wheel or open-cockpit car?It may be used in open-cockpit applications when the applicable rules permit a non-ABP FIA 8860-2018 helmet. Some series require an ABP-homologated helmet, so the current rulebook must be checked before ordering. What is the difference between the SF4 and SF4 ABP?The SF4 ABP has extended protection above the visor and a reduced eyeport to meet Advanced Ballistic Protection requirements. The non-ABP SF4 has a more conventional eyeport and carries FIA 8860-2018 homologation without the ABP designation. Does adding a visor reinforcement strip make the SF4 ABP certified?No. An accessory strip or visor reinforcement panel does not change the helmet’s FIA homologation. Only a helmet manufactured and labeled as an SF4 ABP carries the ABP certification. Where is the Schuberth SF4 manufactured?Schuberth produces its motorsport carbon helmets at its dedicated factory in Italy using hand-laid, autoclave-cured carbon construction. Does the SF4 include a Pinlock anti-fog lens?Yes. Standard SF4 visors are equipped with a Pinlock 120 anti-fog lens. Does the visor include tear-off posts?Yes. Tear-off posts are installed on the standard visor for use with compatible racing tear-offs. How does the two-stage visor lock work?The first stage keeps the visor locked while allowing a controlled amount of ventilation. The second stage creates a firmer visor seal to help keep out fine dust and water. Does the helmet include radio communication equipment?No. Compatible integrated communication electronics are optional and must be selected separately unless specifically included in the purchased configuration. Can the SF4 be connected to a forced-air system?Yes. Compatible top-air and ventilation components are available for configurations that require a forced-air connection. Confirm the orientation and accessory compatibility before ordering. What comes with the Schuberth SF4 helmet?The helmet includes a Schuberth storage pouch. Visor upgrades, tear-offs, ventilation accessories, aerodynamic components, and communication equipment are sold separately unless otherwise stated. How should the Schuberth SF4 fit?The helmet should feel firmly snug with even pressure around the head and cheeks. It should not move independently when secured, but it should not create painful pressure points.

Stilo ST6 GT ZERO Carbon Fiber 8860-2018 Racing Helmet   The Legendary Stilo Carbon ZERO Helmet - Forever Ahead For over 25 years Stilo has lead the way in racing helmet innovation, and the new ST6 line marks a bold new chapter. With input from Porsche and F1 teams, Stilo developed enhanced front and top aerodynamics to deliver exceptional performance from the new Stilo ST6 line of helmets. Developed with the world's top drivers from Formula One and endurance racing, the ST6 reflects real-world needs at ever level of auto racing. The ST6 carbon fiber helmet is one of the lightest helmets on the market. Featuring enhanced airflow, visibility, and comfort while maintaining market-leading safety standards. Developed with input from the Aston martin F1 team, every feature of the ST6 including the track-tested aerodynamics and a cutting edge dual lock visor system, its designed to give racers a performance edge. The Brand New Stilo ST6 helmet improves on the market-leading Stilo ST5 in every way including; 10% Lighter than Stilo ST5 26% More Airflow than Stilo ST5 11% More Visibility More Comfortable Liner and Cheek pads More Shell Sizes for Lower Weight Better Visor Construction for Durability and Ease of Care Higher Quality Visor Hardware for Increased Reliability Stilo ST6 GT ZERO 8860 Carbon Fiber Auto Racing Helmet Features Puro Tech: Stilo's proprietary carbon fiber manufacturing process eliminates the need for extra lacquers or additional coatings, minimizing the weight of your new helmet. With the Puro process, Stilo delivers the lightest and safest helmet on the market. New Shell Size Options: Now offered in four shell sizes, the Stilo ST6 auto racing helmet allows you to receive the lightest and smallest shell size possible for your head shape. Increased Airflow Design: by utilizing our key partnerships with Formula One teams we have redesigned our front ventilation to increase airflow while maximizing safety. The new Stilo ST6 also comes standard with ventilation holes in the top channeling airflow through the EPS foam to reduce sweat and moisture to keep you performing at your best. Increased Downward Visibility: with input from professional drivers around the globe, Stilo has increased the downward Field of view of the Stilo ST6 carbon fiber helmet creating a wider field of vision for greater awareness on the track. Interior Comfort: New and improved, the Stilo ST6 carbon fiber helmet cheek padding is redesigned to enhance stability and increase comfort.   Injection Molded Visor: brand new high performance visors provide exceptional vision and are coated in a new high performance washable anti-fog treatment. Dual Visor Lock: pioneering the industry, this dual visor lock complies with FIA standards both in fully closed and ventilation positions.   Updated Visor Hardware - designed for easy installation and smoother activation, this visor hardware can be purchased in a variety of anodized finishes. Stilo ST6 GT ZERO 8860-2018 Carbon Fiber Auto Racing Helmet Sizing Note We have found that customers who typically wear a size 59 in other brands are most comfortable in a Stilo size 60, which uses the large shell. Please order accordingly. Stilo ST6 GT ZERO 8860-2018 Carbon Fiber Helmet Details Manufacturer: Stilo Helmets Manufacturer part number: AA0800AG3R Homologation: FIA 8860-2018 Compatible shields: Stilo ST6 helmet shields Noise-attenuating earmuffs included Stilo ST6 GT ZERO 8860-2018  SIZING CHART  Measuring Your Head For Your New Stilo ST6 GT ZERO 8860-2018 Carbon Fiber Helmet The most effective helmet is one that fits properly. To measure your head, have an assistant use a dressmaker's tape or a piece of string to measure the circumference of your head. Start at a point about an inch above your eyebrows, looping around the back of your head at the point that results in the largest measurement, and finally around to the front again. It's a good idea to take two or three measurements to make sure you have the largest one. This helmet will ship with signature required for delivery.  

Stilo ST6 FN ZERO Carbon Fiber 8860-2018 Racing Helmet The Stilo ST6 FN ZERO Carbon Fiber Racing Helmet is the flagship non-ABP open-wheel helmet in the ST6 range. Developed using experience from Formula One and other elite racing categories, it combines Stilo’s ultra-light Puro Tech carbon construction with improved aerodynamics, increased airflow, greater downward visibility, and FIA 8860-2018 advanced helmet protection. Designed for drivers who require maximum protection without the reduced eyeport of an ABP helmet, the ST6 FN ZERO delivers a wide field of vision, a compact four-shell sizing platform, redesigned interior padding, and an injection-molded visor secured by Stilo’s dual-position visor locking system. Flagship ST6 Helmet for Formula and Open-Wheel Racing The ST6 FN configuration was developed specifically for open-wheel and open-cockpit competition. Its streamlined shell, stable interior, improved airflow, and expanded downward field of view address the conditions drivers experience in formula cars, prototypes, and other exposed-cockpit vehicles. The FN interior does not rely on permanently integrated GT-style radio electronics. Instead, specially designed padding channels make it easier to route optional communication equipment, air hoses, and hydration components according to the requirements of the driver and vehicle. FIA 8860-2018 Advanced Helmet Protection The Stilo ST6 FN ZERO is homologated to the FIA 8860-2018 advanced helmet standard under homologation number AH.030.24-C. This professional-level standard requires significantly higher impact, penetration, shell-strength, and flame-resistance performance than entry-level motorsport helmet certifications. This model is the standard non-ABP version. It does not include the extended forehead protection and reduced eyeport found on the ST6 FN ZERO ABP. Drivers should confirm whether their championship requires standard FIA 8860-2018 or FIA 8860-2018-ABP homologation before ordering. Puro Tech Carbon Fiber Construction The ST6 FN ZERO uses Stilo’s proprietary Puro Tech carbon fiber manufacturing process. Puro Tech reduces the need for heavy cosmetic lacquer and additional external coatings, allowing the natural carbon shell to remain visible while minimizing unnecessary weight. Each shell is produced with careful control of its carbon layers to create a lightweight, compact helmet capable of meeting the demanding performance requirements of FIA 8860-2018. The exposed carbon finish also gives every helmet the distinctive appearance associated with Stilo’s premium ZERO range. Four Shell Sizes Reduce Weight and Exterior Bulk The ZERO range uses four exterior shell sizes so each interior size can be placed into the smallest appropriate helmet shell. This creates a more proportional fit and avoids surrounding smaller head sizes with unnecessary material and exterior volume. A smaller, lighter shell can improve cockpit clearance, aerodynamic stability, balance, and comfort. It can also reduce the strain placed on the driver’s head and neck during long sessions or repeated high-g cornering. Major Improvements Over the Stilo ST5 ZERO The ST6 platform advances the successful ST5 design with improvements focused on weight, airflow, visibility, comfort, and visor operation. Key updates include: Approximately 10% lower weight than the comparable ST5 Approximately 26% more airflow Approximately 11% greater visibility Improved front and upper-shell aerodynamics Redesigned cheek pads for better comfort and stability Additional shell sizing for a smaller, lighter fit Injection-molded visor construction Washable high-performance anti-fog visor treatment Updated visor pivots and mounting hardware Smoother visor movement and easier shield replacement Improved routing channels for electronics, air, and water systems Formula One-Derived Airflow and Aerodynamics Stilo redesigned the ST6 ventilation system using experience gained from Formula One and other professional racing programs. Revised front vents direct fresh air into the helmet while maintaining the structural integrity required by the FIA standard. Ventilation openings in the top of the shell channel air through the EPS liner to help move heat and moisture away from the driver’s head. This increased airflow can reduce discomfort, visor fogging, and concentration loss during hot or physically demanding races. The front profile and upper shell were also shaped to provide greater aerodynamic stability in high-speed airflow. This is particularly important in open-wheel cars, where the helmet is directly exposed to turbulence around the cockpit and roll structure. Increased Downward Field of View The ST6 eyeport provides greater downward visibility than the ST5. This allows drivers to see steering-wheel displays, switches, harness hardware, cockpit controls, and dashboard information with less head movement. The wider usable viewing area also supports better peripheral awareness when approaching other cars, locating corner apexes, or checking mirrors and display screens inside a tightly packaged cockpit. Redesigned Cheek Padding and Interior Stability Stilo redesigned the ST6 cheek pads to provide a more secure and comfortable fit. The updated shape helps stabilize the helmet during braking, cornering, vibration, and high-speed airflow without relying on excessive pressure against the driver’s face. The improved interior also includes accessible channels for routing optional communication wiring, air-system components, and hydration equipment. This allows the helmet to be customized without forcing equipment between the liner and the driver’s head. Injection-Molded Visor with Washable Anti-Fog Treatment The ST6 FN ZERO uses a high-performance injection-molded visor designed to provide consistent optical clarity across its curved viewing area. This production method improves dimensional consistency and helps reduce the distortion that can occur through conventional formed racing shields. The visor receives Stilo’s washable anti-fog treatment to help maintain clear vision during changing temperatures, humid weather, wet races, and extended driving sessions. The visor should be cleaned only with soft materials and suitable water-based products. Compatible ST6 replacement visors are available in clear, smoked, mirrored, double-glazed, and other specialized configurations. Drivers should select only non-ABP ST6 visors for this helmet. Dual-Position Central Visor Lock Stilo’s central visor locking system provides two positively secured operating positions. Fully Closed: Secures the visor firmly against the eyeport seal for maximum protection and aerodynamic stability. Ventilation Position: Holds the visor slightly open while keeping it mechanically locked and controlled. The ventilation position allows additional airflow without leaving the visor unsecured. The central mechanism also closes the visor evenly and remains accessible while the driver is wearing racing gloves. Updated Visor Hardware The ST6 introduces redesigned pivot hardware and visor sliders for smoother movement, easier installation, and improved reliability. Replacement hardware is available in multiple anodized finishes for drivers who want to personalize the helmet’s appearance. ST5 visors and ST5 visor hardware are not interchangeable with the ST6 system. Replacement shields and components must be specifically listed for the Stilo ST6. Ready for Optional Communications, Air, and Hydration The ST6 FN uses a non-integrated equipment layout. Padding channels make it easier to install compatible earbud systems, microphones, radio wiring, air components, and hydration equipment without permanently building those items into the helmet. Communication electronics, speakers, earbuds, microphones, radio adapters, air-system hardware, and drinking-system components are optional unless specifically included with the selected configuration. Available electronic configurations vary between IMSA, NASCAR, Stilo, Peltor, MRTC, Raceceiver, and other communication systems. Connector compatibility should be confirmed before ordering an electronic kit. Stilo ST6 FN ZERO Helmet Features FIA 8860-2018 advanced helmet homologation FIA homologation number AH.030.24-C Non-ABP full-face configuration Developed for formula and open-wheel racing Stilo Puro Tech carbon fiber construction Exposed lightweight carbon shell finish Four shell sizes for a smaller and lighter proportional fit Approximately 10% lighter than the comparable ST5 Approximately 26% more airflow than the ST5 Approximately 11% more visibility than the ST5 Formula One-derived front ventilation Top ventilation channels through the EPS liner Enhanced high-speed aerodynamics Increased downward field of view Redesigned cheek pads for improved comfort and stability Injection-molded visor Washable high-performance anti-fog treatment Central dual-position visor locking mechanism Secure fully closed and ventilation positions Updated visor hardware for smoother operation Interior routing channels for optional equipment Compatible with optional communication systems Compatible with optional air and hydration accessories Compatible with Stilo ST6 non-ABP visors Stilo ST6 FN ZERO Specifications Manufacturer: Stilo Model: ST6 FN ZERO Manufacturer Part Number: AA0810AG3R Helmet Type: Full-face open-wheel racing helmet Homologation: FIA 8860-2018 FIA Homologation Number: AH.030.24-C ABP Homologated: No Shell Material: Puro Tech carbon fiber Visor Construction: Injection molded Visor Treatment: Washable anti-fog treatment Visor Lock: Central dual-position locking system Compatible Shields: Stilo ST6 non-ABP helmet visors Communication Equipment: Optional and sold separately Air and Hydration Equipment: Optional and sold separately ST6 FN ZERO Versus the ST6 FN ZERO ABP The standard ST6 FN ZERO has a conventional full-face eyeport and carries FIA 8860-2018 homologation without the ABP designation. It provides a wider opening for drivers whose series does not require Advanced Ballistic Protection. The ST6 FN ZERO ABP adds an extended protective structure above the visor and uses a reduced eyeport to satisfy FIA 8860-2018-ABP requirements. An ABP visor, reinforcement strip, or other accessory cannot convert the standard ST6 FN ZERO into an ABP-homologated helmet. ST6 FN ZERO Versus the ST6 GT ZERO The ST6 FN ZERO is configured for open-wheel and open-cockpit racing, with a streamlined non-integrated interior and routing provisions for optional equipment. The ST6 GT ZERO is intended primarily for enclosed race cars and places greater emphasis on cockpit communication, noise control, adjustable ear padding, and GT-style hydration integration. Both use premium ZERO carbon construction, but their interiors and intended installations are different. How to Measure for a Stilo ST6 Helmet Use a soft measuring tape to measure around the widest circumference of your head. Position the tape approximately one inch above the eyebrows, pass it above the ears, and wrap it around the widest point at the back of the head. Keep the tape level and comfortably snug without pulling it tight. Take the measurement two or three times and use the largest consistent result when reviewing the Stilo sizing chart. A properly fitted racing helmet should create firm, even contact around the crown, sides, and cheeks. It should not rotate independently when the chin strap is secured, but it should not create sharp or painful pressure points. Sizing Chart New Shell Size Options - Now offered in four shell sizes, the Stilo ST6 FN Zero auto racing helmet allows you to receive the lightest and smallest shell size possible for your head shape. Questions About the Stilo ST6 FN ZERO Helmet Is the Stilo ST6 FN ZERO certified to FIA 8860-2018?Yes. The ST6 ZERO is homologated to FIA 8860-2018 under homologation number AH.030.24-C. Is this the ABP version of the Stilo ST6?No. This listing is for the standard non-ABP ST6 FN ZERO. Drivers who require Advanced Ballistic Protection must select a helmet specifically labeled and homologated as the ST6 FN ZERO ABP. What type of racing is the ST6 FN designed for?The FN configuration is designed primarily for formula, open-wheel, and other open-cockpit racing applications. What is the difference between the ST6 FN ZERO and the regular ST6 FN 8860?The ZERO uses Stilo’s premium Puro Tech carbon construction and an additional shell size to minimize weight and exterior dimensions. The standard 8860 version uses a different carbon construction while retaining FIA 8860-2018 approval. Does the ST6 FN ZERO include radio communications?No. The helmet is prepared for optional non-integrated communication equipment, but microphones, earbuds, speakers, wiring, connectors, and radio adapters are sold separately unless specifically stated. Does the ST6 FN ZERO include noise-reduction earmuffs?No standard noise-attenuating earmuffs are listed for the FN configuration. Those features are more closely associated with Stilo’s GT and rally-oriented helmet interiors. Can a communication system be added later?Yes. The interior includes routing channels intended to simplify the installation of compatible communication equipment. The correct kit depends on the radio, connector, microphone, and earbud system being used. Can the ST6 FN ZERO use a forced-air system?Yes. Stilo offers compatible top-air and ventilation accessories for the ST6 platform. The correct component depends on helmet shell size, cockpit layout, hose diameter, and connection direction. Does the visor have an anti-fog treatment?Yes. The injection-molded visor uses a washable high-performance anti-fog treatment. Use only suitable water-based cleaning products and soft materials. How does the dual visor lock work?The central mechanism provides a fully closed position and a separate locked ventilation position. Both positions keep the visor positively engaged. Can I use an ST5 visor on the ST6 FN ZERO?No. The ST6 uses a redesigned visor, pivot system, and mounting hardware. Use only shields specifically listed for the Stilo ST6. Can I install an ABP visor on this helmet?An ABP visor does not convert a standard helmet into an ABP-certified model. The helmet remains certified only to the homologation printed on its FIA label. Is the ST6 FN ZERO suitable for a closed-cockpit GT car?It may be permitted when its certification meets the applicable rules, but drivers who need integrated communications, enhanced noise isolation, or adjustable ear padding may prefer the ST6 GT ZERO. Should I automatically order one size larger in Stilo?No. Some drivers who wear size 59 in other brands prefer Stilo size 60, but fit varies by head shape. Measure carefully and compare the result with the current Stilo sizing chart. Signature Required for Delivery This helmet ships with a signature required at delivery due to its value. Someone must be available at the delivery address to sign for the package.

Stilo VENTI WRX Dirt Carbon Zero Helmet The Stilo VENTI WRX Dirt Carbon Zero Helmet is Stilo's premium full-face solution for serious off-road, rally raid, SSV, buggy, and open-vehicle competition. Purpose-built for extreme environments, the WRX Dirt combines an exceptionally wide eyeport, sealed full visor, integrated communications, lightweight Carbon Zero construction, and FIA 8860-2018 protection. Stilo developed the VENTI WRX by combining key strengths of its rally-focused VENTI platform with the full-face protection of its circuit racing helmets. The result is a helmet designed around the unique demands of drivers racing through dust, dirt, mud, heat, rough terrain, and constantly changing conditions. FIA 8860-2018 Carbon Zero Protection The VENTI WRX Dirt Carbon Zero is the highest-performance version of the WRX Dirt platform and is designed for drivers who require FIA 8860-2018 homologation. The Zero version uses Stilo's higher-tensile carbon fiber construction, providing an exceptionally strong shell while keeping overall helmet weight and bulk under control. For competitors racing internationally or in series requiring FIA 8860 certification, the Carbon Zero is the premium WRX Dirt configuration. Purpose-Built for Dirt and Rally Raid The VENTI WRX was not simply adapted from a traditional road-racing helmet. Stilo engineered the platform specifically for raid and off-road competition after working with drivers and teams competing in some of the world's harshest racing environments. The WRX Dirt configuration is specifically designed around open vehicles where the driver is exposed to dust, dirt, rocks, mud, and other debris. Its fully sealed visor provides the coverage of a full-face helmet while maintaining the exceptionally broad visibility needed to read terrain and react quickly. 34% Wider Field of View Visibility is one of the biggest advantages of the Stilo VENTI WRX. Stilo designed the eyeport to provide a 34% increase in field of view compared with the ST5 range. The enlarged opening provides excellent peripheral vision, helping drivers see obstacles, terrain changes, corner entrances, other vehicles, course markers, and the surrounding environment without unnecessary head movement. Despite the dramatically larger opening, the VENTI WRX remains a certified full-face helmet. High-Tensile Carbon Zero Shell Stilo offers the WRX platform in both Carbon and Carbon Zero configurations. The standard Carbon model uses a medium-tensile carbon fiber weave, while the Carbon Zero uses a higher-tensile carbon construction for increased performance. The Zero is the lightest and highest-performing version of the VENTI WRX family and is the model intended for FIA 8860-level competition. Stilo PURO Technology The VENTI WRX Carbon Zero uses Stilo's PURO Super Smooth technology. This manufacturing process produces a high-quality finished carbon surface without requiring the traditional heavy lacquer layer commonly applied to carbon helmets. Eliminating unnecessary clear coat helps reduce weight while also making the helmet more convenient for professional custom painters. Factory graphics are not buried underneath a thick lacquer finish, simplifying preparation for custom helmet designs. Fully Sealed Dirt Visor The WRX Dirt uses a fully sealed visor designed specifically for exposed and debris-heavy environments. The visor helps keep dirt, dust, mud, and other material away from the driver's face and eyes while maintaining a large, clear viewing area. This sealed configuration is one of the primary differences between the WRX Dirt and WRX Raid models. Integrated Rally Communications Communication is built into the VENTI WRX platform rather than treated as an afterthought. The helmet is designed with integrated side ports and comes communication-ready with ear cups and built-in speakers. The system can be used with compatible Stilo intercom equipment, while available adapters allow integration with other communication and radio systems. For driver and co-driver teams, this creates a cleaner installation with fewer loose wires and less equipment competing for space inside the helmet. Top Ventilation for Extreme Conditions Top ventilation openings help move heat and moisture away from the driver's head during demanding race conditions. The top ventilation system can also accommodate compatible Stilo Short Top Air components, providing racers with additional cooling options when their vehicle setup supports forced-air helmet systems. Pre-Installed HANS Posts The VENTI WRX comes with HANS/FHR posts pre-installed, making it ready for use with a compatible Head and Neck Restraint system. This factory-integrated setup eliminates the need to separately install helmet anchors before preparing the helmet for competition. Three-Shell Construction for Better Fit Stilo designed the VENTI WRX around three shell sizes to help place each driver into the smallest and lightest shell appropriate for their head size. Interchangeable cheek pads and top pads also allow the helmet interior to be fine-tuned, giving drivers additional flexibility when dialing in fit and comfort. Extensive WRX Accessory System The VENTI WRX platform was engineered to be highly configurable. Genuine Stilo accessories allow the helmet to be tailored to the driver's vehicle, conditions, communication setup, and personal preferences. Available WRX accessories include alternate full visors, tinted and mirrored visor options, tear-offs, air systems, communication components, peaks, visor fitting hardware, and other competition equipment. Stilo VENTI WRX Dirt Carbon Zero Features FIA 8860-2018 homologation Premium Carbon Zero construction High-tensile carbon fiber weave Stilo PURO Super Smooth technology Purpose-built for off-road and rally raid competition Designed specifically for open vehicles Certified full-face helmet construction 34% wider field of view compared with the ST5 range Fully sealed Dirt visor Integrated communication side ports Ear cups and integrated speakers Pre-installed HANS/FHR posts Top ventilation openings Compatible with available Stilo Short Top Air systems Three shell sizes for optimized fit and weight Interchangeable cheek and top padding Multiple optional visor finishes and accessories available VENTI WRX Dirt vs. VENTI WRX Raid The VENTI WRX Dirt and VENTI WRX Raid share the same wide-vision WRX platform but are configured for different environments. The WRX Dirt is designed specifically for open vehicles and uses a fully sealed full visor to maximize protection from dirt and debris. The WRX Raid is aimed primarily at closed vehicles and can be configured with a short visor and adjustable peak. For an open buggy, SSV, rally raid vehicle, or other application where the driver's face is exposed to the environment, the WRX Dirt is the more protective configuration. VENTI WRX Carbon Zero vs. Carbon The WRX Carbon uses Stilo's medium-tensile carbon fiber construction, while the WRX Carbon Zero steps up to a higher-tensile carbon weave and is positioned as the lighter, higher-performance version of the helmet. The Carbon Zero is also the WRX configuration to choose when FIA 8860 homologation is required. Why the WRX Dirt Eyeport Matters Off-Road Off-road drivers need to process considerably more than a conventional racing line. Terrain changes, rocks, ruts, course markers, competitors, and obstacles can appear from multiple directions. The VENTI WRX's exceptionally large eyeport gives the driver more peripheral information without sacrificing the coverage of a full-face design. That combination is what separates the WRX from a conventional closed-cockpit racing helmet. Getting the Proper Stilo Helmet Fit A racing helmet should fit firmly and evenly around the entire head. It should not move independently when the driver turns or shakes their head, but it should also avoid concentrated pressure points that become painful during longer sessions. Use a flexible measuring tape around the widest part of the head, approximately one inch above the eyebrows and around the back of the skull. Take the measurement two or three times and use the largest consistent measurement when comparing your head circumference with the Stilo sizing chart. Stilo VENTI WRX Dirt Carbon Zero Helmet Sizing Chart Questions & Answers What certification does the Stilo VENTI WRX Dirt Carbon Zero have?The VENTI WRX Dirt Carbon Zero is the FIA 8860-2018 version of the WRX Dirt platform and is designed for high-level motorsport competition requiring FIA 8860 homologation. What is special about the Carbon Zero version?The Carbon Zero uses Stilo's higher-tensile carbon fiber construction and is positioned as the lightest and highest-performing version of the WRX family. How much more visibility does the VENTI WRX provide?Stilo states that the WRX provides a 34% increase in field of view compared with the ST5 helmet range. Is the VENTI WRX Dirt a full-face helmet?Yes. Despite its extremely large eyeport, the WRX is designed, tested, and certified as a full-face helmet. What is the difference between the WRX Dirt and WRX Raid?The WRX Dirt is intended for open vehicles and uses a fully sealed visor for protection from dirt and debris. The WRX Raid is primarily designed for closed vehicles and can be configured with a short visor and peak. Does the WRX Dirt include communications?The VENTI WRX platform includes integrated communication provisions with ear cups, built-in speakers, and side ports for connection to compatible Stilo intercom or radio equipment. Does the helmet come with HANS anchors?Yes. HANS/FHR posts are pre-installed on the VENTI WRX. Can I use a forced-air system with the WRX Dirt?Yes. The helmet's top ventilation openings can be used with compatible Stilo Short Top Air components. Are replacement visors available?Yes. Stilo offers WRX Dirt full visors in several configurations, including clear, smoked, mirrored, and colored iridium options. Can the interior fit be adjusted?Yes. The WRX uses interchangeable cheek and top pads, allowing the interior fit to be fine-tuned when the correct shell size has been selected. Is the Carbon Zero different from the standard WRX Carbon?Yes. The standard Carbon uses a medium-tensile carbon weave, while the Carbon Zero uses Stilo's higher-tensile carbon construction and is the FIA 8860 version of the WRX platform. Is the WRX Dirt designed specifically for dusty conditions?Yes. The sealed full visor and full-face construction are specifically intended to protect the driver in demanding dirt, dust, mud, and debris-heavy environments. Does this helmet require a signature for delivery?Yes. This helmet ships with signature required for delivery.

Stilo VENTI WRX Raid Carbon Zero Helmet The Stilo VENTI WRX Raid Carbon Zero Helmet is Stilo's premium full-face rally raid and off-road helmet engineered for drivers and co-drivers competing in demanding closed-vehicle environments. Combining the wide visibility of the VENTI rally platform with the protection of a full-face helmet, the WRX Raid delivers exceptional peripheral vision, lightweight Carbon Zero construction, integrated communications, and FIA 8860-level protection. Designed specifically for rally raid, off-road racing, SSVs, buggies, and other extreme motorsport applications, the VENTI WRX platform was developed to handle environments where heat, dust, rough terrain, long stages, and constant communication place unique demands on the driver and equipment. FIA 8860 Carbon Zero Protection The VENTI WRX Raid Carbon Zero is the highest-performance version of Stilo's WRX Raid platform. The Carbon Zero construction uses a higher-tensile carbon fiber weave and is the WRX configuration intended for competitors who require FIA 8860 homologation. This premium carbon construction provides the strength required for professional motorsport while controlling helmet weight and overall shell size, making the Carbon Zero an excellent choice for long-duration rally raid and off-road competition. Purpose-Built for Rally Raid and Closed Vehicles The WRX Raid is specifically configured for closed-cockpit rally raid and off-road vehicles. Instead of the sealed full visor used on the WRX Dirt, the Raid configuration uses a short peak and an open eyeport designed to work with off-road or motocross-style goggles. This setup gives drivers the flexibility to choose goggles appropriate for dust, changing light, heat, and demanding desert or trail conditions while maintaining the full-face protection of the WRX helmet platform. 34% Wider Field of View One of the biggest advantages of the Stilo VENTI WRX is its exceptionally large eyeport. Stilo engineered the WRX to provide a 34% increase in field of view compared with the ST5 helmet range. The expanded opening improves peripheral visibility and allows the driver to see more of the cockpit, terrain, obstacles, corners, course markers, and surrounding vehicles without excessive head movement. The eyeport is also large enough to accommodate popular off-road and motocross goggles, making it particularly useful for rally raid and SSV competition. Goggle-Compatible Raid Design The VENTI WRX Raid is designed specifically around goggle use. Its large eyeport provides the room needed for off-road goggles while the short peak helps reduce glare and provides additional protection from overhead light and debris. For racers who prefer a short visor rather than goggles, compatible WRX short visor options are also available, allowing the helmet to be configured around the driver's preferred setup. High-Tensile Carbon Zero Shell The standard VENTI WRX Carbon uses a medium-tensile carbon fiber weave, while the Carbon Zero steps up to Stilo's higher-tensile carbon construction. The result is Stilo's lightest and highest-performing WRX configuration, developed for competitors who want maximum performance from the platform while meeting the requirements of FIA 8860 competition. Stilo PURO Super Smooth Technology The WRX Carbon Zero uses Stilo's PURO Super Smooth technology. This construction process creates a high-quality finished carbon surface without requiring a conventional heavy lacquer layer. Eliminating unnecessary clear coat helps reduce weight and also makes the helmet easier for professional painters to prepare for custom graphics because factory decals are not buried beneath a traditional lacquer finish. Integrated Rally Communications The VENTI WRX was engineered around communications from the beginning. The helmet features integrated side ports and comes with Stilo's rally communication equipment, including ear cups and built-in speakers. The system can connect to compatible Stilo intercoms, while available adapters allow the helmet to be integrated with a variety of other motorsport radio and communication systems. For driver and co-driver teams, this integrated setup creates a cleaner installation with fewer loose wires and less equipment competing for space inside the helmet. Pre-Installed HANS Posts The VENTI WRX comes with HANS/FHR posts pre-installed, allowing the helmet to be used with a compatible Head and Neck Restraint system without requiring separate helmet anchor installation. Top Ventilation for Long Rally Stages Top ventilation openings help reduce heat and moisture buildup inside the helmet during long and physically demanding rally stages. The top ventilation openings are also designed to accommodate the compatible Stilo Short Top Air System, giving drivers the option of adding forced-air cooling when their vehicle setup allows it. Side Air System Compatibility The VENTI WRX Raid can also be configured with Stilo's available Side Air system. This gives racers another way to route forced air into the helmet depending on cockpit configuration and available vehicle equipment. The ability to choose between multiple cooling configurations makes the WRX Raid particularly adaptable for long-duration desert and rally raid competition. Drinking System Compatibility Stilo designed the WRX Raid to accommodate an available drinking system, allowing drivers to integrate hydration equipment directly into their race setup. For endurance-style events such as rally raid and long off-road stages, integrated hydration capability can help reduce distractions and make it easier for drivers to stay hydrated without removing safety equipment. Three Shell Sizes for a Better Fit The VENTI WRX platform is manufactured using three shell sizes rather than forcing every helmet size into the same outer shell. This allows Stilo to keep the exterior dimensions and weight better matched to the driver's actual head size. Interchangeable cheek pads and top pads also allow the interior fit to be fine-tuned for improved comfort and stability. Designed for Extreme Motorsport Conditions The WRX platform was developed specifically around the requirements of modern rally raid and off-road competition. Drivers may spend hours dealing with vibration, heat, rough terrain, dust, navigation, communication, and constant changes in visibility. The combination of a large eyeport, full-face protection, integrated communications, lightweight carbon construction, cooling-system compatibility, and hydration options makes the VENTI WRX Raid particularly well suited to these demanding environments. Stilo VENTI WRX Raid Carbon Zero Features FIA 8860 homologation Premium Carbon Zero construction High-tensile carbon fiber weave Stilo PURO Super Smooth technology Purpose-built for rally raid and off-road competition Designed primarily for closed vehicles Certified full-face helmet construction 34% wider field of view compared with the ST5 range Large goggle-compatible eyeport Short peak Raid configuration Compatible WRX short visor options available Integrated communication side ports Integrated ear cups and speakers Pre-installed HANS/FHR posts Top ventilation openings Compatible with Stilo Short Top Air systems Side Air system available Drinking system available Three shell sizes for optimized fit and weight Interchangeable cheek pads and top pads Wide range of WRX accessories available VENTI WRX Raid vs. VENTI WRX Dirt The VENTI WRX Raid and VENTI WRX Dirt share the same wide-vision WRX foundation but are configured for different types of vehicles and racing environments. The WRX Raid is designed primarily for closed vehicles and uses a short peak with an open, goggle-compatible eyeport. The WRX Dirt is intended primarily for open vehicles and uses a fully sealed full visor to provide increased protection from dirt, dust, mud, and flying debris. For drivers competing inside an enclosed rally raid vehicle who prefer goggles or the flexibility of a short visor and peak, the WRX Raid is the purpose-built configuration. VENTI WRX Carbon Zero vs. Carbon The standard WRX Carbon uses Stilo's medium-tensile carbon fiber weave, while the WRX Carbon Zero uses a higher-tensile carbon construction. The Carbon Zero is the lightest and highest-performing version of the WRX platform and is the model intended for international competition where FIA 8860 homologation is required. Why the Wide Eyeport Matters in Rally Raid Rally raid drivers must process considerably more visual information than a conventional racing line. Terrain changes, navigation markers, obstacles, competitors, cockpit instruments, and course hazards can all require immediate attention. The VENTI WRX's large eyeport increases peripheral visibility and reduces the amount of head movement required to see the surrounding environment. This is especially useful during technical off-road stages where conditions can change rapidly. WRX Accessory Compatibility Stilo developed the WRX as a highly configurable helmet system. Available accessories allow the Raid to be tailored around the driver's vehicle, weather conditions, communication equipment, cooling setup, and personal preferences. Compatible equipment includes short and extended peaks, short visors in multiple finishes, air systems, drinking systems, communication components, tear-offs, and additional WRX-specific hardware. Getting the Proper Stilo Helmet Fit A properly fitted racing helmet should feel firm and even around the entire head without excessive movement or isolated pressure points. Use a flexible measuring tape around the widest portion of the head, approximately one inch above the eyebrows and around the back of the skull. Take the measurement two or three times and use the largest consistent measurement when comparing your head circumference with the Stilo helmet sizing chart. Sizing Chart Questions & Answers What certification does the Stilo VENTI WRX Raid Carbon Zero have?The Carbon Zero is the WRX version intended for FIA 8860 competition and is designed for racers who require Stilo's highest-performance WRX construction. What is the difference between the WRX Raid and WRX Dirt?The WRX Raid is primarily designed for closed vehicles and uses a short peak with a goggle-compatible eyeport. The WRX Dirt is designed primarily for open vehicles and features a fully sealed full visor. Does the VENTI WRX Raid use goggles?Yes. The Raid configuration is specifically designed to work with off-road or motocross-style goggles. Can I use a visor instead of goggles?Yes. Stilo offers compatible WRX short visor options in several finishes, allowing the Raid to be configured without goggles when preferred. How much more visibility does the WRX provide?Stilo states that the VENTI WRX provides a 34% increase in field of view compared with the ST5 helmet range. Does the WRX Raid include communications?Yes. The WRX platform comes communication-ready with integrated side ports, ear cups, and built-in speakers for use with compatible Stilo intercoms or other radio systems through available adapters. Does the helmet come with HANS anchors?Yes. HANS/FHR posts are pre-installed on the VENTI WRX. Can the VENTI WRX Raid use a forced-air system?Yes. The helmet supports compatible Stilo Short Top Air equipment and can also be configured with available Side Air components. Can a drinking system be installed?Yes. Stilo offers drinking-system equipment compatible with the WRX Raid platform. What is PURO technology?Stilo's PURO Super Smooth manufacturing process creates a finished carbon surface without requiring a conventional heavy lacquer layer, helping reduce unnecessary weight. What is the difference between Carbon and Carbon Zero?The standard WRX Carbon uses a medium-tensile carbon fiber weave, while the Carbon Zero uses a higher-tensile weave and is the WRX version intended for FIA 8860 competition. Can the interior fit be adjusted?Yes. The VENTI WRX uses interchangeable cheek pads and top pads to help fine-tune fit after the correct helmet and shell size have been selected. Is the WRX Raid only for rally raid?No. Although it was specifically developed for raid and off-road competition, the wide field of view and configurable WRX platform can also make it useful for other motorsport applications where visibility, communications, and flexible accessory configurations are important. Does this helmet require a signature for delivery?Yes. This helmet ships with signature required for delivery.     The most effective helmet is one that fits properly. To measure your head, have an assistant use a dressmaker's tape or a piece of string to measure the circumference of your head. Start at a point about an inch above your eyebrows, looping around the back of your head at the point that results in the largest measurement, and finally around to the front again. It's a good idea to take two or three measurements to make sure you have the largest one. This helmet will ship with signature required for delivery.

Stilo ST6 FN ABP Carbon Fiber 8860-2018 Racing Helmet The Stilo ST6 FN ABP Carbon Fiber Racing Helmet is built for professional drivers who demand Stilo's highest level of open-cockpit protection without sacrificing weight, airflow, visibility, or comfort. Developed with direct input from Formula 1 and endurance racing teams, the ST6 generation advances the championship-proven ST5 platform with updated aerodynamics, a redesigned ventilation system, improved downward visibility, new interior padding, and an entirely new visor system. This FN ABP version combines Stilo's lightweight Carbon PURO Tech construction with FIA 8860-2018 ABP homologation. Advanced Ballistic Protection extends the protected area across the forehead, making the ST6 FN ABP specifically suited to high-level open-wheel and open-cockpit racing where protection from airborne debris is critical. FIA 8860-2018 Advanced Ballistic Protection ABP stands for Advanced Ballistic Protection. The ST6 FN ABP incorporates an extended protective area across the forehead to address the additional hazards faced by drivers in exposed cockpits. The FIA 8860-2018 ABP configuration represents one of Stilo's highest-specification full-face racing helmet platforms and is intended for competitors operating at professional and international levels of motorsport. Developed with Formula 1 Experience Stilo developed the ST6 with extensive input from drivers and teams competing at the highest levels of Formula 1 and endurance racing. Feedback from professional drivers influenced the helmet's airflow, visibility, comfort, aerodynamics, and hardware. The result is not simply a cosmetic update to the ST5. The ST6 was re-engineered around the real demands of modern high-speed race cars, particularly open-wheel applications where aerodynamic stability, cooling, vision, and helmet security all become more critical. Carbon PURO Tech Shell The ST6 FN uses Stilo's Carbon PURO Tech construction, developed to produce an extremely lightweight carbon shell while maintaining the structural performance required for elite motorsport. PURO technology minimizes unnecessary finishing materials and coatings, allowing the carbon construction itself to deliver a clean finished surface while reducing excess weight. Up to 11% Lighter Than the ST5 Weight reduction was a major focus during development of the ST6. Stilo states that the new generation can be up to 11% lighter than the ST5 while delivering improved safety performance. Reducing helmet mass can be especially valuable in formula and open-cockpit racing, where high lateral loads, braking forces, aerodynamic buffeting, and long race durations place substantial stress on the driver's neck. Three-Shell Sizing System The ST6 range uses three shell sizes to better match the exterior helmet dimensions to the driver's actual head size. Rather than placing a broad range of sizes into a single oversized shell, this approach helps keep the helmet as compact and light as practical for each driver. Stilo also offers an additional extra-small Zero shell on selected ST6 Zero models. F1-Inspired Airflow System The ST6 FN ABP features a redesigned airflow system based on Stilo's Formula 1 experience. Front ventilation was reshaped to move more air through the helmet while maintaining the structural and aerodynamic requirements of high-level competition. Top ventilation openings channel air through the helmet's internal structure to help reduce heat, sweat, and moisture during demanding race sessions. Improved Downward Field of View Stilo increased the ST6's downward field of vision compared with the ST5. This change provides drivers with improved visibility toward the steering wheel, dashboard, controls, mirrors, and nearby cockpit surroundings. The additional visibility can be especially useful in formula and prototype cockpits where the seating position and surrounding bodywork can make downward sightlines particularly important. Injection-Molded ST6 ABP Visor The ST6 introduces a new injection-molded visor designed for optical performance, durability, and smoother operation. The visor receives Stilo's new high-performance washable anti-fog treatment, helping maintain clear vision while allowing the visor to be cleaned and maintained more easily than traditional anti-fog coatings. The ST6 FN ABP requires the dedicated Stilo ST6 ABP visor family to maintain the helmet's Advanced Ballistic Protection configuration. Dual-Position Visor Lock Stilo redesigned the visor locking mechanism for the ST6 generation. The system is engineered to comply with current FIA requirements with the visor in both the fully closed position and ventilation position. This allows the driver to use a controlled partially open setting for additional airflow while retaining a secure mechanical locking system. Updated Visor Hardware New visor pivots, sliders, and mounting hardware provide smoother operation and easier installation compared with the previous generation. The updated design also makes visor removal and replacement more straightforward when changing between clear, tinted, mirrored, or other compatible ST6 ABP shields. Improved Cheek Pad Stability The ST6 uses newly designed cheek padding intended to improve both comfort and helmet stability. The revised shape helps hold the helmet securely around the driver's face while reducing unnecessary pressure during long sessions. This is especially important in open cars where wind loading, vibration, and high cornering forces can continually act on the helmet. Designed for Open-Cockpit Performance The ST6 FN ABP interior and aerodynamic package are specifically optimized for performance in open cars. The combination of improved cheek support, airflow management, ABP forehead protection, and refined external aerodynamics makes the helmet particularly well suited to formula, prototype, and other exposed-cockpit race cars. Communication-System Ready The ST6 FN ABP is prepared for installation of multiple Stilo communication configurations. Internal routing provisions allow compatible microphones, earbud connections, earmuff speaker systems, radio connections, and other electronic components to be integrated cleanly into the helmet. This gives teams flexibility to configure the helmet around the communication system required by the car, championship, or driver's preference. Integrated Equipment Routing Stilo redesigned the internal padding channels of the ST6 platform to simplify installation of racing electronics and related equipment. The routing system helps keep communication wiring and other components organized while minimizing interference with helmet fit and driver comfort. Stilo ST6 FN ABP Carbon Fiber Features FIA 8860-2018 ABP homologation Advanced Ballistic Protection Extended forehead protection area Carbon PURO Tech shell construction Developed with Formula 1 and endurance racing input Up to 11% lighter than the ST5 generation Three-shell sizing system F1-inspired redesigned airflow system Top ventilation openings for heat and moisture management Increased downward field of view compared with the ST5 New comfort cheek padding Improved cheek stability Injection-molded visor High-performance washable anti-fog treatment Dual-position FIA-compliant visor locking system Secure visor locking in fully closed and ventilation positions Redesigned visor hardware for smoother movement Dedicated ST6 ABP visor compatibility Ready for multiple communication-system configurations Internal routing for electronics and communication equipment Special comfort design optimized for open cars ST6 FN ABP vs. ST6 FN The primary difference between the ST6 FN ABP and standard ST6 FN is the additional Advanced Ballistic Protection incorporated into the ABP model. The standard ST6 FN provides the core ST6 carbon construction, airflow, visibility, visor, and comfort improvements. The ST6 FN ABP adds the extended forehead protection required for ABP homologation and uses dedicated ST6 ABP visors. ST6 FN ABP vs. ST6 FN Zero ABP Both models provide Advanced Ballistic Protection, but the ST6 FN Zero ABP represents Stilo's ultimate weight-focused configuration and provides access to the additional smaller Zero shell for the appropriate head sizes. The standard ST6 FN ABP offers the same core ST6 design philosophy and FIA 8860-2018 ABP protection in Stilo's Carbon PURO Tech construction. ST6 ABP Visor Compatibility The ST6 FN ABP requires dedicated Stilo ST6 ABP visors. Genuine ST6 ABP shields are available in multiple configurations, including clear, smoked, silver, mirrored, and double-glazed options. Because the ABP visor is part of the helmet's protective system, standard non-ABP ST6 visors should not be substituted when ABP compliance is required. Getting the Correct ST6 Fit Stilo revised its sizing and shell structure for the ST6 generation, so drivers moving from an ST5 should not automatically assume that the same labeled size will provide an identical fit. A correctly fitted helmet should provide light, even pressure around the entire head without isolated pressure points. The helmet should remain stable when the head moves and should not rotate independently around the driver's head. Measure around the widest part of the head with a flexible measuring tape, approximately one inch above the eyebrows and around the rear of the skull. Take the measurement multiple times and compare the largest consistent measurement with the ST6 sizing chart. Stilo ST6 FN ABP Carbon Fiber Racing Helmet Sizing Chart Questions & Answers What certification does the Stilo ST6 FN ABP Carbon Fiber Helmet have?This model is homologated to FIA 8860-2018 ABP, combining FIA 8860-level helmet performance with Advanced Ballistic Protection. What does ABP mean?ABP stands for Advanced Ballistic Protection. The ST6 FN ABP incorporates an extended protected area across the forehead to provide additional protection against airborne debris in exposed-cockpit racing. Is the ST6 FN ABP intended for open-wheel racing?Yes. Stilo specifically designed the ABP model and its comfort padding for high-performance open-car applications where aerodynamic loading and debris exposure are major considerations. Is the ST6 FN ABP carbon fiber?Yes. The ST6 FN platform uses Stilo's Carbon PURO Tech construction to combine high structural performance with very low helmet weight. How much lighter is the ST6 than the ST5?Stilo states that the ST6 generation can be up to 11% lighter than the ST5 while providing improved safety performance. Does the ST6 have better visibility than the ST5?Yes. The ST6 has an increased downward field of view compared with the ST5, improving visibility of the cockpit and surrounding environment. What is different about the ST6 visor?The ST6 uses a new injection-molded visor with a high-performance washable anti-fog treatment, redesigned pivot hardware, and smoother visor movement. Does the visor lock when it is partially open?Yes. Stilo's dual-position locking system is engineered to secure the visor in both the fully closed and ventilation positions. Can I use a standard ST6 visor on the ABP helmet?Use the dedicated Stilo ST6 ABP visor family on the ST6 FN ABP. The ABP visor configuration is specifically designed around the helmet's Advanced Ballistic Protection system. Can communications be installed in the ST6 FN ABP?Yes. The helmet is prepared for multiple communication configurations, including compatible microphone, earbud, earmuff speaker, and radio systems. How many shell sizes does the ST6 FN ABP use?The standard ST6 range uses three shell sizes to optimize exterior dimensions and weight. An additional XS Zero shell is available on selected ST6 Zero models. Is the ST6 FN ABP the same as the ST6 FN Zero ABP?No. Both offer Advanced Ballistic Protection, but the Zero ABP is Stilo's more extreme weight-focused configuration and includes access to the additional compact Zero shell where applicable. Can the ST6 interior fit be adjusted?Yes. Different cheek and crown padding options can be used to fine-tune the fit after the correct base helmet size has been selected. Does this helmet require a signature for delivery?Yes. This helmet ships with signature required for delivery

Stilo Venti WRC 8860-2018 Carbon Fiber Racing Helmet Unsurpassed Excellence: The Stilo Venti WRC Carbon 8860-2018 The new Stilo Venti WRC Carbon Fiber racing helmet features lightweight, durable carbon fiber construction using their smallest carbon fiber shell. It's made even lighter using Stilo's innovative PURO technology, eliminating the final clear coat layer. The result is very light weight without compromising maximum protection. Stilo Venti WRC Carbon Fiber FIA 8860-2018 Certified This Stilo Venti WRC Carbon Fiber Helmet is homologated to the FIA 8860-2018 certification standard, the toughest auto racing helmet standard in the world. The Stilo Venti WRC Carbon Fiber 8860-2018 Helmet is a professional-grade helmet trusted by professional and amateur racers alike. With its unique ventilation system, the Stilo Venti WRC offers superior airflow to keep you cool and focused during long races and under extreme conditions. The interior padding of the Stilo Venti WRC can be easily removed and cleaned, ensuring a fresh and comfortable fit for every race. Innovative New Features for Exceptional Performance The Stilo Venti WRC is the update of the legendary WRC helmet as worn by multiple rally champions. This helmet features many improvements, most notably the innovative wireless (WL) communication system. While retaining Stilo's market-leading helmet electronics, the Venti WRC comms port was re-designed to use the WL wireless key (sold separately). The WL key doesn't interfere with FHR posts or straps, and allows the driver and co-driver to communicate inside and outside the car. The Stilo Venti WRC has a mic boom with new geometry to maximize both visibility and sound quality, allowing you to maintain focus and concentration on the track ahead. The Stilo Venti WRC also features an all-new aggressive design including an adjustable visor that lets you customize your field of view under different driving conditions. The Pinnacle of Performance, Innovation, and Safety The Stilo Venti WRC Carbon Fiber 8860-2018 sits at the pinnacle of motorsport safety and performance, offering uncompromising quality and class-leading innovation. The Stilo Venti WRC Carbon Fiber gives you unparalleled safety, comfort, and performance on the race track. Supplied with factory fitted HANS Post anchors as standard. The most effective helmet is one that fits properly. To measure your head, have an assistant use a dressmaker's tape or a piece of string to measure the circumference of your head. Start at a point about an inch above your eyebrows, looping around the back of your head at the point that results in the largest measurement, and finally around to the front again. It's a good idea to take two or three measurements to make sure you have the largest one. This helmet will ship with signature required for delivery.

Stilo ST6 GT Carbon Fiber 8860-2018 Racing Helmet The Legendary Stilo Carbon Helmet - Forever Ahead For over 25 years Stilo has lead the way in racing helmet innovation, and the new ST6 line marks a bold new chapter. With input from Porsche and F1 teams, Stilo developed enhanced front and top aerodynamics to deliver exceptional performance from the new Stilo ST6 line of helmets. Developed with the world's top drivers from Formula One and endurance racing, the ST6 reflects real-world needs at ever level of auto racing. The ST6 carbon fiber helmet is one of the lightest helmets on the market. Featuring enhanced airflow, visibility, and comfort while maintaining market-leading safety standards. Developed with input from the Aston martin F1 team, every feature of the ST6 including the track-tested aerodynamics and a cutting edge dual lock visor system, its designed to give racers a performance edge. The Brand New Stilo ST6 helmet improves on the market-leading Stilo ST5 in every way including; 10% Lighter than Stilo ST5 26% More Airflow than Stilo ST5 11% More Visibility More Comfortable Liner and Cheek pads More Shell Sizes for Lower Weight Better Visor Construction for Durability and Ease of Care Higher Quality Visor Hardware for Increased Reliability Stilo ST6 GT 8860 Carbon Fiber Auto Racing Helmet Features Puro Tech - Stilo's proprietary carbon fiber manufacturing process eliminates the need for extra lacquers or additional coatings, minimizing the weight of your new helmet. With the Puro process, Stilo delivers the lightest and safest helmet on the market. New Shell Size Options - Now offered in three shell sizes, the Stilo ST6 auto racing helmet allows you to receive the lightest and smallest shell size possible for your head shape. Increased Airflow Design - by utilizing our key partnerships with Formula One teams we have redesigned our front ventilation to increase airflow while maximizing safety. The new Stilo ST6 also comes standard with ventilation holes in the top channeling airflow through the EPS foam to reduce sweat and moisture to keep you performing at your best.   Increased Downward Visibility - with input from professional drivers around the globe, Stilo has increased the downward Field of view of the Stilo ST6 carbon fiber helmet creating a wider field of vision for greater awareness on the track.   Interior Comfort - New and improved, the Stilo ST6 carbon fiber helmet cheek padding is redesigned to enhance stability and increase comfort.   Injection Molded Visor - brand new high performance visors provide exceptional vision and are coated in a new high performance washable anti-fog treatment. Dual Visor Lock - pioneering the industry, this dual visor lock complies with FIA standards both in fully closed and ventilation positions.   Updated Visor Hardware - designed for easy installation and smoother activation, this visor hardware can be purchased in a variety of anodized finishes. Stilo ST6 GT 8860-2018 Carbon Fiber Auto Racing Helmet Sizing Note We have found that customers who typically wear a size 59 in other brands are most comfortable in a Stilo size 60, which uses the large shell. Please order accordingly. Stilo ST6 GT 8860-2018 Carbon Fiber Helmet Details Manufacturer: Stilo Helmets Manufacturer part number: AA0800AG1R Homologation: FIA 8860-2018 Compatible shields: Stilo ST6 helmet shields Noise-attenuating earmuffs included Other Versions of the Stilo ST6 Racing Helmet Stilo ST6 GT SA2020 Carbon Fiber Helmet Stilo Helmet ST6 FN 8859-ABP Helmet Stilo ST6 FN Zero 8860-2018 Carbon Fiber Helmet Stilo ST6 FN Zero ABP 8860-2018 Carbon Fiber Helmet Stilo ST6 GT Composite Helmet Stilo ST6 FN 8859-ABP Helmet Stilo ST6 FN 8860 Carbon Fiber Helmet Stilo ST6 FN 8860-ABP Carbon Fiber Helmet Stilo ST6 FN Carbon Fiber Helmet Stilo ST6 GT ZERO 8860-2018 Carbon Fiber Helmet Measuring Your Head For Your New Stilo ST6 GT 8860-2018 Carbon Fiber Helmet The most effective helmet is one that fits properly. To measure your head, have an assistant use a dressmaker's tape or a piece of string to measure the circumference of your head. Start at a point about an inch above your eyebrows, looping around the back of your head at the point that results in the largest measurement, and finally around to the front again. It's a good idea to take two or three measurements to make sure you have the largest one. This helmet will ship with signature required for delivery.

Stilo ST6 FN Carbon Fiber 8860-2018 Racing Helmet The Legendary Stilo Carbon Helmet - Forever Ahead For over 25 years Stilo has lead the way in racing helmet innovation, and the new ST6 line marks a bold new chapter. With input from Porsche and F1 teams, Stilo developed enhanced front and top aerodynamics to deliver exceptional performance from the new Stilo ST6 line of helmets. Developed with the world's top drivers from Formula One and endurance racing, the ST6 reflects real-world needs at ever level of auto racing. The ST6 carbon fiber helmet is one of the lightest helmets on the market. Featuring enhanced airflow, visibility, and comfort while maintaining market-leading safety standards. Developed with input from the Aston martin F1 team, every feature of the ST6 including the track-tested aerodynamics and a cutting edge dual lock visor system, its designed to give racers a performance edge. The Brand New Stilo ST6 helmet improves on the market-leading Stilo ST5 in every way including; 10% Lighter than Stilo ST5 26% More Airflow than Stilo ST5 11% More Visibility More Comfortable Liner and Cheek pads More Shell Sizes for Lower Weight Better Visor Construction for Durability and Ease of Care Higher Quality Visor Hardware for Increased Reliability Stilo ST6 FN 8860 Carbon Fiber Auto Racing Helmet Features Puro Tech - Stilo's proprietary carbon fiber manufacturing process eliminates the need for extra lacquers or additional coatings, minimizing the weight of your new helmet. With the Puro process, Stilo delivers the lightest and safest helmet on the market. New Shell Size Options - ST6 FN Now offered in four shell sizes, the Stilo ST6 FN auto racing helmet allows you to receive the lightest and smallest shell size possible for your head shape. Increased Airflow Design - by utilizing our key partnerships with Formula One teams we have redesigned our front ventilation to increase airflow while maximizing safety. The new Stilo ST6 also comes standard with ventilation holes in the top channeling airflow through the EPS foam to reduce sweat and moisture to keep you performing at your best. Increased Downward Visibility - with input from professional drivers around the globe, Stilo has increased the downward Field of view of the Stilo ST6 carbon fiber helmet creating a wider field of vision for greater awareness on the track. Interior Comfort - New and improved, the Stilo ST6 carbon fiber helmet cheek padding is redesigned to enhance stability and increase comfort. Injection Molded Visor - brand new high performance visors provide exceptional vision and are coated in a new high performance washable anti-fog treatment. Dual Visor Lock - pioneering the industry, this dual visor lock complies with FIA standards both in fully closed and ventilation positions. Updated Visor Hardware - designed for easy installation and smoother activation, this visor hardware can be purchased in a variety of anodized finishes. Stilo ST6 FN 8860-2018 Carbon Fiber Auto Racing Helmet Sizing Note We have found that customers who typically wear a size 59 in other brands are most comfortable in a Stilo size 60, which uses the large shell. Please order accordingly. Stilo ST6 FN 8860-2018 Carbon Fiber Helmet Details Manufacturer: Stilo Helmets Manufacturer part number: AA0810AG1R Homologation: FIA 8860-2018 Compatible shields: Stilo ST6 helmet shields Noise-attenuating earmuffs included Other Versions of the Stilo ST6 Racing Helmet Stilo ST6 GT SA2020 Carbon Fiber Helmet Stilo Helmet ST6 FN 8859-ABP Helmet Stilo ST6 FN Zero 8860-2018 Carbon Fiber Helmet Stilo ST6 FN Zero ABP 8860-2018 Carbon Fiber Helmet Stilo ST6 GT Composite Helmet Stilo ST6 FN 8859-ABP Helmet Stilo ST6 GT 8860 Carbon Fiber Helmet Stilo ST6 FN 8860-ABP Carbon Fiber Helmet Stilo ST6 FN Carbon Fiber Helmet Stilo ST6 GT ZERO 8860-2018 Carbon Fiber Helmet Measuring Your Head For Your New Stilo ST6 FN 8860-2018 Carbon Fiber Helmet The most effective helmet is one that fits properly. To measure your head, have an assistant use a dressmaker's tape or a piece of string to measure the circumference of your head. Start at a point about an inch above your eyebrows, looping around the back of your head at the point that results in the largest measurement, and finally around to the front again. It's a good idea to take two or three measurements to make sure you have the largest one. This helmet will ship with signature required for delivery.

Bell HP10 Rally Helmet Introducing the Bell HP10 Rally helmet - the epitome of advanced helmet technology, drawing inspiration from Bell's esteemed HP7 Advanced Helmets. Proudly FIA 8860-2018 approved, this modern masterpiece is not just an open-face rally helmet; it's a statement of performance. Crafted with an ultra-lightweight carbon shell, it features a quick-detach Half Chin-Bar (HCB), adjustable carbon fiber peak, and a state-of-the-art adjustable integrated sunscreen. Prioritizing both comfort and sound insulation, it stands as the go-to choice for rally drivers and co-drivers aiming for the pinnacle of their craft. Bell Racing Helmets dedicated R&D team collaborated with audio experts and elite rally drivers, ensuring unparalleled sound insulation and communication. Embedded with ZeroNoise electronics, potent speakers, and a noise-cancelling microphone, the Bell HP10 Rally helmet promises unmatched safety, comfort, and communication. Bell HP10 Rally Helmet Features Homologation: FIA 8860-2018 Exterior: matte finish carbon fiber Interior: dark grey high-strength Comfort FR fabric. Open face design with ultra-lightweight advanced full carbon shell. Removable carbon Half Chin-Bar (HCB) easily detaches for fast airway access in an emergency. ZeroNoise electronics, high-power speakers, and noise-cancelling mic integrated in HCB. Advanced multi-density, multi-piece liner maximizes energy absorption and impact performance. Factory installed HANS anchors. Adjustable integrated anti-scratch sunscreens: ML Red Mirror (M10S-Short) installed, Dark Smoke (M10-Long) supplied in the box. Removable cheek pads with multi-density advanced materials for optimal comfort. Ultra-reliable, heavy duty in-molded female Nexus connector. Adjustable carbon fiber sun peak. Air extraction holes maximize cooling. Bell HP10 Rally Helmet Size Chart Bell HP10 Rally Helmet Options Alternative interior fabric colors: Tan, White, Red, Purple, Blue, Green and Neon Yellow (each by special order). Adjustable sunscreens available in various colors and two lengths to ensure optimal visual comfort. Sizes (in cm): 54, 55, 56, 57, 58, 59, 60, 61, and 61+.

Sparco Prime RF-10 Supercarbon The Supercar of Helmets Hey, race track royalty! Ever feel like your current helmet is more of a tortoise than a hare? Time to trade that old noggin-protector in for something more... speedy. Introducing the Sparco Prime RF-10 8860 Supercarbon Helmet - the crown jewel of racing gear. Imagine the union of sheer beauty and beastly strength - that's the Sparco Supercarbon for you. This carbon-fiber-crafted beauty isn't just for show‚ its certified to the highest FIA standards. That means, whether you're pulling G's on the track or casually setting lap records, this bad boy is ready to rumble. Speaking of rumble, ever had your visor fog up during an intense lap? Annoying, right? The RF-10's got you covered with a crystal-clear view, thanks to its brilliant chin ventilation system. Plus, the center visor locking mechanism is like Fort Knox for your face‚ secure and safe. Thirsty mid-race? No worries! It's prepped to accommodate a drinks system. Yeah, you heard right. It's like a mini fridge, but for your head. This helmet isn't just about the outside though. Inside, it's plush and comfortable. After a sweaty race, you can pop out that interior lining and give it a wash. Talk about staying fresh! Sparco Prime RF-10 Supercarbon Product Highlights: Strong visor game: comes with a clear visor. Looking for that mysterious racer vibe? Opt for the dark smoke visor (sold separately).The visor (FIA approved) can also be infinitely adjusted. Approved and certified: FIA 8860-2018 & Snell SA2020 approved. Wash and wear: Removable interior lining, because who doesn't love freshness? Stay hydrated: accommodates an optional drink system. Head and neck safety: comes with factory fitted FHR posts. Racers, it's time to upgrade. Because while they say it's not about the gear but the driver, a bit of Sparco Supercarbon magic doesn't hurt either. So, ready to be the envy of the track? Hit that 'Add to cart' button and let the Sparco Prime RF-10 8860 Supercarbon helmet take you to the finish line in style and safety! The Sparco Prime RF-10 8860 Supercarbon helmet is homologated to the latest and highest FIA standard currently available making this helmet ready to use in any motorsport discipline. The radically designed carbon fiber shell is lightweight yet extremely strong, engineered to withstand the most rigorous of accidents. A center visor locking mechanism ensures a positive and safe visor closure, while the chin ventilating system provides maximum air flow through the helmet ensuring the visor stays clear. The Sparco Prime RF-10 8860 Supercarbon helmets ventilation is provided by air intakes situated on the front of the race helmet that gives maximum air flow through the helmet ensuring the visor stays clear. The top ventilation acts as an exhaust to remove excess heat and condensation. The interior lining of the helmet is also removable which allows it to be washed very easily. FIA 8860-2018 and Snell SA2020 approved. Please note: Sparco Prime RF-10 8860 Supercarbon helmet is supplied with a clear visor. Pictured with an optional dark smoke visor. Sparco Prime RF-10 8860 Supercarbon Helmet Size Chart Sparco Prime RF-10 8860 Supercarbon Helmet Frequently Asked Questions (FAQ): Remember that safety is paramount in auto racing, and choosing the right helmet and maintaining it properly is essential for your protection on the track. Consult the professionals at Competition Motorsport any time you have specific questions about your racing helmet. Why do I need a racing helmet? Auto racing helmets are designed to protect drivers from head injuries and fire during high-speed races and crashes. They are a crucial safety component in motorsports. How do I choose the right size Sparco Prime RF-10 Supercarbon? You should measure your head's circumference using a flexible tape measure, then refer to the manufacturer's sizing chart to select the appropriate size helmet. Please review our blog posting on how to properly fit your new auto racing helmet from Competition Motorsport. What safety standards should I look for in a racing helmet? Look for helmets that meet safety standards like Snell and FIA depending on your racing discipline. These standards ensure the helmet's safety and quality. DOT helmets are designed for street use and not for racing and track use. What's the difference between full-face and open-face, and helmets? Full-face helmets provide the most protection with a complete face shield, while open-face helmets cover the top and sides of the head. Can I use a motorcycle helmet for auto racing? No, motorcycle helmets do not provide the same level of protection as auto racing helmets, as they are designed for different purposes. It's recommended to use a helmet specifically designed for auto racing which includes fire protection in addition to impact protection. How often should I replace my Sparco Prime RF-10 Carbon Fiber auto racing helmet? Auto racing helmets should be replaced every 5-10 years, depending on the manufacturer's recommendations and usage. If the helmet is involved in a crash, it should be replaced immediately. Are expensive racing helmets safer than budget ones? In a word, yes. Safety standards dictate the minimum requirements a helmet must meet, so even budget-friendly helmets offer some protection. More expensive helmets typically exceed minimum standards and have much more R&D and engineering behind their design. They are usually lighter weight,constructed of superior materials, fitment is more customizable, and often come with additional features. How do I maintain and clean my Sparco Prime RF-10 Carbon Fiber racing helmet? Follow the manufacturer's instructions for cleaning and maintenance. You should clean the exterior, interior and shield with the Molecule Matte Helmet Care Kit. Do I need to wear a balaclava under my Sparco Prime RF-10 Carbon Fiber racing helmet? Balaclavas are typically not required for Driver's Education events, however they make wearing a helmet much, much more comfortable. Balaclavas will provide fire protection (if fire rated), help keep your helmet lining clean and order free by absorbing the majority of sweat while using it, and additionally balaclavas make putting your helmet on and taking it off by protecting your ears and keeping from from folding over when you helmet is worn. Competition Motorsport recommends balaclavas from Alpinestars, OMP, Sabelt, Sparco, and Stand21. If you are entering sanctioned auto racing events, balaclavas will be required for fire protection. Is the SNELL SA rating important? The Snell SA2020 certification is a safety standard established by the Snell Memorial Foundation for auto racing helmets. It sets the criteria and requirements that helmets must meet to be considered safe and suitable for use in motorsport events. Snell SA2020 certification is highly regarded in the motorsports industry and is often required or recommended by racing organizations and events. It signifies that a helmet has passed rigorous testing to provide maximum safety for drivers in various motorsport disciplines, including road racing, NASCAR, Formula 1, drag racing, and more. It's essential for drivers to check the specific safety standards required by the racing organizations they participate in to ensure compliance. Is the FIA helmet certification important? Yes, FIA (F√©d√©ration Internationale de l'Automobile) certification is crucial for auto racing helmets, especially in the context of international motorsport events and many national and regional racing series in the USA. The FIA 8859-2015 standard is commonly associated with racing helmets used in various motorsport disciplines. Helmets certified to FIA 8859-2015 met the safety requirements set by the FIA and were widely accepted in many racing series Which helmet certification is the most stringent and the hardest to meet? The FIA 8860-2018 certification is considered the most stringent and advanced helmet certifications available for auto racing helmets, and it is often associated with top-tier motorsport categories like Formula 1. It's important to note that the FIA 8860-2018 helmets offer a high level of protection and their use is mandatory in many racing series. Drivers should always check the regulations of the racing series they intend to participate in to ensure compliance with helmet certification standards. Can I wear glasses with my Sparco Prime RF-10 Carbon Fiber helmet? Most helmets have provisions for wearing glasses or goggles, but check the design to be sure. Most manufacturers feature helmet models with wider eye ports to better accommodate eye glasses. Are carbon fiber helmets better? Carbon fiber helmets are lightweight and strong, a top choice for racers. But remember, certification matters most. Can I use a used helmet for racing? It's best to buy a new helmet. Used helmets may have unseen damage or be out of date on safety standards. Can I buy replacement parts for my Sparco Prime RF-10 Carbon Fiber helmet, like visors or padding? Competition Motorsport carries Sparco helmet replacement parts, including visors and padding, to extend your helmet's lifespan. How can I prevent helmet fogging during races? Anti-fog sprays and inserts are available to help keep your visor clear during races. What's the importance of proper helmet ventilation? Proper ventilation helps keep you cool and comfortable during races, reducing the risk of heat exhaustion. How do I store my Sparco Prime RF-10 Carbon Fiber helmet between races? Keep it in a cool, dry place away from direct sunlight and chemicals in a bag designed to store your auto racing helmet, like the Competition Motorsport Evo Helmet Bag Where can I buy a certified racing helmet? You should only buy from a professional, authorized dealer who has sold thousands of helmets. You can find all the best brands at Competition Motorsport online or visit our retail store at Atlanta Motorsports park or at one of the hundreds of race and track day events we attend and support. Remember, safety should always come first in auto racing. Choose a certified helmet that meets the necessary standards to protect yourself on the track. We take immense pride in offering a wide selection of Sparco auto racing helmets, designed to meet the demands of professional racers and motorsports enthusiasts alike. Sparco has been at the forefront of helmet innovation and safety for decades, earning a reputation as a top-tier brand in the racing world. Key Features of Sparco Racing Helmets: Unparalleled Safety: Sparco racing helmets are engineered to the highest safety standards, including certifications like Snell and DOT approval, ensuring your head is well-protected in high-speed racing conditions. Premium Materials: Crafted with precision, Sparco helmets feature carbon fiber construction, making them lightweight yet incredibly strong for maximum protection. Comfort and Fit: Sparco's commitment to comfort is evident in the design of their helmets. They offer a range of sizes, and many models have customizable padding to ensure a snug fit. Aerodynamic Design: Sparco helmets are designed with aerodynamics in mind, reducing wind resistance and enhancing performance on the track. Frequently Asked Questions About Sparco Helmets: Where are Sparco helmets made? Sparco helmets are proudly manufactured in Italy, maintaining the highest quality standards. Is Sparco a good helmet brand? Yes, Sparco is renowned for its commitment to safety, innovation, and performance, making it a trusted choice among professional racers and enthusiasts. Are Sparco helmets Snell approved? Yes, many Sparco helmets are Snell approved, meeting rigorous safety standards. Are Sparco helmets FIA approved? Absolutely, several Sparco helmets are FIA 8860-2018 certified, ensuring they meet the most stringent safety requirements. Do Sparco helmets run small? Sparco offers a variety of sizes and often provides sizing charts to help you choose the right fit. It's important to measure your head and refer to their guidelines for a proper fit. For racers who demand the best in safety and performance, Sparco auto racing helmets are the ultimate choice. Explore our extensive collection to find the perfect helmet for your racing needs. Sparco Racing Helmets: Sparco Racing Helmets are renowned for their exceptional quality and safety features. With a wide range of models to choose from, you can find the perfect Sparco Racing Helmet to suit your racing needs. Sparco Racing Helmet: Each Sparco Racing Helmet is a product of meticulous craftsmanship and cutting-edge technology. When you wear a Sparco Racing Helmet, you're choosing a helmet that prioritizes your safety and performance on the track. Sparco Race Helmets: Sparco Race Helmets come in various styles and designs to cater to different types of motorsports. Whether you're into karting, open-wheel racing, or stock car racing, Sparco has race helmets tailored for your specific discipline. Sparco Race Helmet: Your Sparco Race Helmet is more than just protective gear; it's a crucial part of your racing ensemble. The aerodynamic design of a Sparco Race Helmet helps reduce wind resistance, giving you a competitive edge. Sparco Helmet: A Sparco Helmet is a symbol of trust in motorsports. Professional racers and amateurs alike rely on the comfort, safety, and durability that Sparco Helmets provide during intense racing conditions. Sparco Helmets: Sparco Helmets have a rich history of innovation and excellence. The extensive range of Sparco Helmets ensures that there's a model suitable for every racer, whether you're a seasoned pro or just starting in the sport. Sparco Carbon Fiber Helmet: Sparco Carbon Fiber Helmets combine the lightweight properties of carbon fiber with advanced safety features. These helmets are a top choice for racers seeking the ultimate in protection without sacrificing comfort. Race Car Helmet: A race car helmet is a fundamental piece of safety gear for any racer. Sparco's race car helmets are engineered to meet the rigorous demands of motorsports, ensuring you stay safe on the track. Racing Helmet: Your racing helmet is your shield against potential accidents. Sparco Racing Helmets are designed to offer superior impact protection while maintaining optimal visibility and ventilation. Racing Helmets: Racing helmets are a racer's best friend. Sparco Racing Helmets, with their reputation for quality and safety, are the go-to choice for many professionals and enthusiasts in the racing community. Sparco Racing: Sparco Racing is synonymous with excellence in the motorsports industry. Their commitment to research, development, and testing has solidified their position as a leader in racing helmet technology. Auto Racing Helmet: When it comes to auto racing, your helmet is your first line of defense. Sparco Auto Racing Helmets are engineered to withstand the rigors of high-speed racing, ensuring your head is protected. Auto Racing Helmets: Auto racing helmets from Sparco are designed to provide optimal head protection while maintaining lightweight and aerodynamic qualities, allowing you to perform at your best.