Brey Krause R-1032 Harness Bar 991 & 992
Brey Krause Brey Krause R-1032 Harness Bar 991 & 992 $879.53
Brey Krause R-1032 Harness Bar Porsche 991 & 992 (NON-TARGA) Harness Mount Bar pictured has a custom powder coat. All Mount Bars come with a wrinkle black powder coat.  The 991 harness mount bar has been tested and certified by an independent lab to handle the types of forces required by the National Highway Traffic Safety Admin. DOT and SAE J385 Rev.MAR 95, Motor Vehicle Seat Belt Anchorages-Performance Requirements. The 991 harness mount bar properly locates and supports racing shoulder harnesses relative to the driver. In the case of an accident, it helps protect the driver's shoulders and spine. The harness guides also prevent excessive shifting and fatigue of the driver during the high G loads of cornering and braking. Our bars are easy to install and remove, use only existing holes and mounting points, and will not damage the car in any way. Strength requirements for harness mounts are considerably greater than those for harness guide bars since they must support the entire load applied to the belts. A mount really can't be relied on unless it has been tested to support the loads required by the National Highway Traffic Safety Administration. The Brey-Krause Harness Mount supported the loads specified by the National Highway Traffic Safety Admin. DOT for upper torso restraints in all automobiles. Tensile tests performed by an independent lab. FEATURES: Material: Type 304, stainless steel Miscellaneous: Bar is designed to allow enough seat travel for tall drivers. Includes provisions for Seat Back Brace. Installation: Bar attaches to seat belt mounts & seat track hardware. Models: 991 & 992 (Targa models must use R-1033 down tubes) Weight: 16 lbs Finish: Powder coated in durable black wrinkle-finish
Brey Krause R-1120 Harness Bar C6 Corvette
Brey Krause Brey Krause R-1120 Harness Bar C6 Corvette $1,017.38
Brey Krause R-1120 Harness Bar C6 Corvette The Brey Krause Model R-1120 Harness Bar for the C6 Corvette properly locates and supports racing shoulder harnesses relative to the driver. In the case of an accident, it helps protect the driver's shoulders and spine. The harness guides also prevent excessive shifting and fatigue of the driver during the high G loads of cornering and braking. Our bars are easy to install and remove, and will get you ready for the track in just a few hours!NOTE: Because of mounting locations in the C6, the B-pillar plastic sail panel covers will require two holes to be drilled through them. Brey-Krause provides plastic plugs to cover the holes if the bar is ever removed. Sail panels replacements can be ordered from your GM Dealer (Part 15277640 for driver side, and 15277641 for passenger side) if the plastic plugs are not the desired solution. Strength requirements for harness mounts are considerably greater than those for harness guide bars since they must support the entire load applied to the belts. FEATURES: Material: Type 304, stainless steel Finish: Powder coated in durable black wrinkle-finish Weight: 17.2 lbs. Installation: Bar attaches to factory mounting points in "B" pillars.
Brey Krause R-1125 Harness Bar C7 Corvette (all coupes)
Brey Krause Brey Krause R-1125 Harness Bar C7 Corvette (all coupes) $968.93
Brey Krause R-1125 Harness Bar C7 Corvette The Brey Krause Model R-1125 Harness Bar for the C7 Corvette properly locates and supports racing shoulder harnesses relative to the driver. In the case of an accident, it helps protect the driver's shoulders and spine. The harness guides also prevent excessive shifting and fatigue of the driver during the high G-force loads of cornering and braking. Brey Krause bars are easy to install and remove, and will get you ready for the track in just a few hours! Note: Because of mounting locations in the C7, the B-pillar plastic sail panel covers will require a slot on either side to be cut. Sail panel replacements can be ordered from your GM dealer if you don't want to cut the original panels (Part 23176134 for driver side, and part 23176135 for passenger side). Strength requirements for harness mounts are considerably greater than those for harness guide bars since they must support the entire load applied to the belts. FEATURES: Material: Type 304 stainless steel Finish: Powdercoated in durable black wrinkle-finish Weight: 17.12 lbs Installation: Bar attaches to factory mounting points in B-pillars FITS: 2014+ C7 Stingray, Z51, Z06, and ZR1 Coupes
Brey Krause R-1155 Harness Bar Gen5-6 Camaro
Brey Krause Brey Krause R-1155 Harness Bar Gen5-6 Camaro $783.71
Brey Krause R-1155 Harness Bar Gen6 Camaro The Brey Krause Model R-1155 Harness Bar for the 2015 and later Chevrolet Camaro properly locates and supports racing shoulder harnesses relative to the driver. In the case of an accident, it helps protect the driver's shoulders and spine. The harness guides also prevent excessive shifting and fatigue of the driver during the high G loads of cornering and braking. Easy to install and remove, the Brey Krause R-1155 Harness Bar uses existing holes and mounting points, and requires no vehicle modification. Kit includes everything needed for a proper 4-point harness set-up, while allowing enough seat travel for the tallest of drivers. Fits all Sixth-Gen Chevrolet Camaro models (2015+) Material: Type 304, stainless steelFinish: Powdercoated in durable black wrinkle-finish Weight: 16 lbs.Installation: Bar attaches to factory mounting points in "B" pillars.
CMS Performance Deluxe Harness Bar For C8 Corvette
Competition Motorsport CMS Performance Deluxe Harness Bar For C8 Corvette $995.00
CMS Performance Deluxe Bolt-In Harness Bar For C8 Corvette FITMENT 2020+ Chevrolet Corvette Stingray (C8) Does not fit Convertible or Roadster Click Here For Installation Instructions The C8 Corvette is an incredible, affordable track-day car that easily achieves race car performance on track. Managing that kind of performance wearing nothing but a three-point seat belt is a chore and leaves a lot to be desired in terms of safety. That's where we come in with the CMS Performance C8 Corvette Deluxe Harness Bar. Featuring the same rock-solid, high-strength design as our standard C8 Harness Bar, the Deluxe bar adds an innovative "main hoop" design, giving it a more aggressive look. This also gives you a place to mount an in-car motorsports video camera, like the AiM Sports SmartyCam GP HD. Of course, it provides high-strength mounting points for your harness shoulder straps to keep you firmly and safely in your seat. The C8 Deluxe Harness Bar is the strongest, most elegantly designed C8 harness bar on the market. It seamlessly integrates into your C8 interior, preserves your rear view, and gives the C8 a big bump in cool factor, especially with a custom powder-coat color! The CMS C8 Deluxe Harness Bar allows full seat travel while locating your harness shoulder belts at the proper height for maximum on-track safety and security. Installation requires no drilling or other modification of the chassis, and no modification of your upper center console trim. Some modification of your B-pillar lock/seat belt trim panels is required. We offer precision pre-cut panels to ease installation and save your originals if you need to put your C8 back to stock. DESIGNED AND BUILT IN THE USA Every CMS C8 Deluxe Harness Bar is handcrafted in America by master fabricators for a perfect fit, beautifully 360o TIG welded for high strength, and fully powder-coated in our facility for a brilliant, durable finish. And there's no extra charge for custom colors. CMS operates a complete powder-coating facility to offer you color-matched Corvette factory colors, giving your C8 a customized look that will last. CNC mandrel bent and fully TIG welded from premium Docol R8 Advanced High-Strength Steel (stronger than 4130 CrMo or DOM) and finished in rich powder-coat. Complete, detailed instructions make installation pretty simple (figure about an hour if you're reasonably handy). Add optional four-point Schroth Profi II ASM Harnesses and our Harness Install Kit, and you're ready to hit the track. These harnesses were specifically designed for use in street cars with no sub strap pass-through in the seat.   FEATURES 1.50″ x .095" Docol R8 Advanced High-Strength Steel for superior safety Full 360o TIG welding for ultimate strength, integrity, and beauty Custom-color powder coating is included -- any color you can imagine! Lightweight at only 24 lbs., yet incredibly strong Unobstructed rear view Designed, built, and powder-coated in the USA Allows full seat travel with any seat Comes with all necessary hardware THIS PRODUCT IS INTENDED FOR OFF-ROAD USE ONLY  
CMS Performance Harness Bar For C8 Corvette
Competition Motorsport CMS Performance Harness Bar For C8 Corvette $795.00
CMS Performance Bolt-In Harness Bar For C8 Corvette FITMENT 2020+ Chevrolet Corvette Stingray (C8) - Does Not Fit Convertible / Roadster Click Here For Installation Instructions The C8 Corvette is an incredible, affordable track-day car that easily achieves race car performance on track. Managing that kind of performance wearing nothing but the three-point seat belt is a chore and leaves a lot to be desired in terms of safety. That's where we come in with the CMS Performance C8 Corvette Harness Bar. This provides a rock-solid, high-strength bar to mount shoulder straps for a 4-, 5-, or 6-point racing harness to keep you firmly and safely in your seat. The CMS Performance C8 Harness Bar is the strongest, most elegantly designed C8 harness bar on the market. It seamlessly integrates into your C8 interior, and we custom powder coat it whatever color you choose, including factory color-matched hues. The CMS C8 bar allows full seat travel while locating your harness shoulder belts at the proper height for maximum on-track safety and security. Installation requires no drilling or other modification of the chassis, and only minor modification of your interior trim. You can add our precision pre-cut OEM trim to ease the install, preserving your original trim should you want to put your Corvette back to stock in the future. DESIGNED AND BUILT IN THE USA Every CMS harness bar is handcrafted in America by master fabricators for a perfect fit, beautifully 360o TIG welded for high strength, and fully powder-coated in our facility for a brilliant, durable finish. And there's no extra charge for custom colors. CMS operates a complete powder-coating facility to offer you color-matched Corvette factory colors, giving your C8 a customized look that will last. CNC mandrel bent and fully TIG welded from premium Docol R8 Advanced High-Strength Steel (stronger than 4130 CrMo or DOM) and finished in rich powder-coat.   Complete, detailed instructions make installation pretty simple (figure about an hour if you're reasonably handy). Installation requires modifying the two lock/seat belt trim panels and the upper trim of your center console. We offer two levels of pre-cut trim to ease installation: first, just the upper console (the most visible and most difficult to trim correctly); second the upper console plus the two lock/seat belt trim panels. Our installation instructions also include cutting templates should you decide to modify your existing trim. Add optional four-point Schroth Profi II ASM Harnesses and our Harness Install Kit, and you're ready to hit the track. These harnesses were specifically designed for use in street cars with no sub strap pass-through in the seat.  FEATURES 1.50″ x .095" Docol R8 Advanced High-Strength Steel for superior safety Full 360o TIG welding for ultimate strength, integrity, and beauty Custom-color powder coating is included -- any color you can imagine! Lightweight at only 18 lbs., yet incredibly strong Unobstructed rear view Designed, built, and powder-coated in the USA Allows full seat travel with any seat Comes with all necessary hardware THIS PRODUCT IS INTENDED FOR OFF-ROAD USE ONLY
sale
CMS Performance Harness Install Kit For C8 Corvette
00
DAYS
00
HRS
00
MIN
00
SEC
Competition Motorsport CMS Performance Harness Install Kit For C8 Corvette from $125.00 $250.00
CMS Performance Harness Install Kit For C8 Corvette Fits 2020+ Chevrolet Corvette Stingray (C8) The CMS Performance Harness Install Kit for the C8 Corvette allows you to install the lap belts for a four-point harness in your C8 Corvette. This kit is typically used in conjunction with our CMS Performance C8 Harness Bar or Deluxe C8 Harness Bar to locate the shoulder straps of your harness. Each Harness Install Kit is for one seat (driver or passenger side, they're interchangeable). Order two and save! DESIGNED AND BUILT IN THE USA Designed and built in the USA, this Harness Install Kit is CNC cut and fully TIG-welded from high-strength stainless steel and powder-coated satin black to blend seamlessly into your interior when you don't have harnesses installed. Complete, detailed instructions make installation pretty simple (figure about an hour if you're reasonably handy). We recommend the Schroth Profi II ASM Harnesses as a perfect complement to this kit. Schroth's proprietary Anti-Submarine (ASM) technology was developed specifically for use in street cars with no sub strap pass-through in the seats. INSTALLATION INSTRUCTIONS CLICK HERE FEATURES Crafted from Stainless Steel for superior safety Full 360o TIG welding for strength, integrity, and beauty Powder coated satin black Designed, built, and powder-coated in the USA Simple installation in about an hour THIS PRODUCT IS INTENDED FOR OFF-ROAD USE ONLY
CMS Performance Porsche 981-718 Cayman Harness Bar
Competition Motorsport CMS Performance Porsche 981-718 Cayman Harness Bar from $1,195.00
CMS Performance Bolt-In Harness Bar for Porsche 981 & 718 Cayman FITS: 2012+ Porsche Cayman (Base, S, GTS, GT4) Made from high-strength, fully TIG welded Docol R8 Advanced High-Strength Steel tubing, the CMS Performance Harness Bar is the strongest and safest bolt-in harness bar on the market for your Porsche 981 Cayman. It gives you the perfect attachment for your five- or six-point harness shoulder straps without having to install a full roll bar. The welded-in strap hoops keep them aligned with your shoulders. The CMS Harness Bar is designed to place the shoulder straps at the proper angle (0° to -20°) and distance (eight inches or less) to the driver, regardless of seat position, without cutting the Cayman's center carpeted "hump". This design also provides an ideal location to mount an AiM SmartyCam . The CMS Harness Bar doesn't interfere at all with access to the engine cover. It mounts to the frame structure across the passenger compartment bulkhead, directly behind the seats. TIG welded by our master welders, the integrity, fit, and finish of the CMS Harness Bar is unsurpassed. The standard color for the bar is satin black (as pictured) to complement any interior. Or we can custom powder-coat it to match your car at no extra charge! Some cutting of your OEM plastic trim will be required. CMS offers precision pre-cut OEM Porsche trim as an option to ease installation and preserve your original trim! FEATURES: 1.50″ x .120" Docol R8 Advanced High-Strength Steel No cutting of the center carpeted "hump" to preserve OEM carpet CNC-cut mounting plates Designed and built in the USA Allows full seat travel with any seat Easy to install and perfect fitment guaranteed Detailed Installation Instructions and all necessary hardware