The best highest performance racing brake fluid on the market today is CMS Performance RF1 with a dry boiling point of 622ºF!
Competition Motorsport CMS Performance RF1 DOT4 Racing Brake Fluid (500 ml) from $24.95
CMS Performance RF1 DOT4 622oF Racing Brake Fluid Buy in bulk and save. Get six bottles and save 15%, or a case of 12 and save a whopping 25%! The Highest Dry Boiling Point Racing Brake Fluid You Can Buy CMS Performance RF1 fully synthetic Racing Brake Fluid is formulated to provide the highest performance under racing and track-day conditions, where braking systems operate at very high sustained temperatures. RF1 exceeds all DOT 3 & 4 requirements and is compatible with all DOT 3, 4, and 5.1 fluids. (Not compatible with DOT5 or mineral-based brake fluids.) There is perhaps no single safety system more important in racing than brakes. And no part of that system is more critical than brake fluid. At Competition Motorsport, we got tired of (and a little nervous) using "racing" brake fluid on the track that didn't live up to its claimed performance. So we did something about it. Manufactured in partnership with Orthene Chemicals, a British brake fluid supplier to professional race teams in Formula 1, WEC, and many other pro series, CMS Performance RF1 Racing Brake Fluid is formulated to maintain consistent viscosity, lubricity, and compressibility at extreme temperatures and line pressures found in racing, track days, and spirited driving. Bottom line: you can spend more money, but you can't buy higher-performing racing brake fluid! CMS Performance RF1 Racing Brake Fluid Specifications: Typical dry boiling point: 622° F (328° C) Typical wet boiling point: 399° F (204° C) Exceeds DOT3 & DOT4 standards Individual 500 ml (16.7 oz.) bottles Click Here For The RF1 Product MSDS Sheet A Note About Brake Fluid Boiling Points DOT 4 brake fluid like RF1 is hygroscopic, meaning it attracts water over time sitting in your brake lines and reservoir. At high brake temperatures, this water can boil in your car's brake lines, causing the fluid in the lines to become compressible. That's what you feel when you experience brake fade. This is why the "wet" (aged fluid) boiling point of any brake fluid is substantially lower than the "dry" (brand new fluid) boiling point. Since time is the enemy of brake fluid performance, the best practice is to replace your racing brake fluid before each track event/weekend. At a minimum, flush it with new fluid at least every three months if you're consistently racing and/or driving at track days. A couple bottles of fluid will flush most sports cars or race cars. It ends up being pretty cheap insurance against learning about brake fade the hard way.
Girodisc Pad Spreader GDPS01
Girodisc Girodisc Pad Spreader GDPS01 $250.00
Girodisc Brake Pad Spreader This indispensable tool is used by race teams, shops, and enthusiasts alike who have high performance four- and six-piston calipers. The spreader is designed to spread brake pads and pistons in four- and six-piston calipers to facilitate quick replacement of pads and/or rotors in a shop or racing environment.No more screwdrivers, pliers, hammers, or C-clamps! This tool will retract the pistons evenly and all the way back into their bores with one squeeze of the levers. The Girodisc spreader was designed around popular four-piston and six-piston calipers from Brembo, AP Racing, Alcon, and other performance calipers in racing and road use. To help fit in any caliper, the amount of throw is adjustable.Insert the spreading plates one way for wider six-piston calipers, then turn the spreader 90o and use the plate sides for four-piston calipers.The Girodisc Pad Spreader is made from heavy-gauge steel and is powder-coated for durability. The slider is cadmium-plated, and nylon pivot bushings ensure smooth action. The Girodisc Pad Spreader will quickly become an invaluable tool for any race team, shop, or enthusiast who changes pads and rotors with any frequency.
Pagid Racing Brake Pads No. 2487
Pagid Pagid Racing Brake Pads No. 2487 from $340.23
 Fits These Vehicles: Make Model Build (Year) Front Rear Alfa Romeo Giulia 2.9 [952] 15 -   X Aston Martin DB 9 04 - X   Aston Martin Vantage V8 GT4 ProDrive [race car] 12 - X   Audi RS3 Sportback [8PA] 11 - 12 X   Audi TT RS 2.5 Quattro 09 - 14 X   Cadillac CTS-V (4 piston front caliper) 03 - 09 X   Chevrolet Camaro SS 09 - 15 X   Chevrolet Camaro SS - 4 Piston Brembo caliper 16 - X   Chevrolet Corvette Brembo 6 piston non ceramic 09 -   X Chevrolet Corvette C7 base 14 - X   Chevrolet Corvette C7 Z51 14 - X   Dodge Viper SRT TA (time attack) 14 - X X Ford GT 04 - 06 X X Ford Mustang Boss 302 12 - 13 X   Ford Mustang GT [4 piston Brembo] 15 - X   Ford Mustang Shelby GT500 [4 piston Brembo caliper / 15" disc] 07 - 14 X   Honda (Acura) Acura TL 04 - X   Honda (Acura) Civic IX Type R [Brembo brakes] 15 - X   Hyundai Genesis Coupe 3.8 track 10 - X   Maserati Ghibli (M157) [4 piston Brembo caliper / disc ø 345mm] 13 - X   Mitsubishi Lancer Evo V - Evo IX 98 - 06 X   Mitsubishi Lancer Evo X 07 - 16 X   Renault Mégane III 2.0 RS [Brembo brakes] without electronic hand brake 08 - X   Subaru STI 3rd & 4th generation 03 - 16 X   Volvo S60 Turbo R Brembo brakes 03 - X   Volvo V70 R 2.5T Brembo brakes 03 - X   RSL 29: The PAGID RS29 (Yellow) is the world-leading endurance brake pad used by most of the winning teams in motorsport. Although designed primarily for endurance racing, many competitors use this material successfully for sprint and short distance races also. RS29 has also found favor in the growing track day market due to the level of control, good cold performance, long life and low disc wear. RS 14: The PAGID RS14 (Black) is a high friction value ceramic compound with very good modulation and high fade resistance. A very popular, aggressive pad with strong initial bite and high torque. In addition to the track-day environment, RS14 has shown success in short- to medium-distance circuit racing as well as gravel and tarmac rallying. RSL1: PAGID RSL1 has a high ceramic content with superior thermal insulation and higher heat resistance than metallic pad compounds. They feature excellent pad wear under endurance conditions, excellent rotor life, and are less aggressive than RST pads with excellent brake balance and modulation.
MP-1001-2 Girodisc Magic Pads (Front)
Girodisc MP-1001-2 Girodisc Magic Pads (Front) $95.00
GiroDisc "Magic Pads" are the solution to your squeaky, dusty, expensive factory replacement pads. They have lower dust than typical factory pads and much less than other performance pads. You won't be cleaning your wheels nearly as often! Additionally, they have great initial bite, something most less-expensive pads lack. But the real reason people like Magic Pads so much is they are the "silver bullet" to brake noise problems. Magic Pads are a semi-metallic composition that is easy on rotors and on your wallet. We recommend always replacing pads as a whole car set when switching compounds. All Magic Pads come with anti-noise shields pre-installed and included in the price. If you have any questions, give us a call at (844) 438-7244. We're happy to help!
Sold out
SS-1001  Girodisc S-S Pads (Front)
Girodisc SS-1001 Girodisc S-S Pads (Front) $120.00
The Girodisc S/S or "street/strip" pads represent the ultimate in high performance brake pads. The semi-metallic compound maintains a consistent coefficient of friction from 0o to 1000o F, making them an ideal option for people who are looking for a dual-purpose pad that works really well on both the street and the race track. The formula has very little compressibility, ensuring a very firm pedal and immediate bite and making the S/S pads a favorite among autocrossers and drivers who demand the most out of their street cars. Inevitably, these will dust more than Girodisc Magic Pads, but with the Girodisc anti-noise shims that come on every set of pads they will not make any noise if they are bedded-in properly. We recommend always replacing pads as a whole car set when switching compounds. All S/S pads come with anti-noise shims pre-installed and included in the price. If you have any questions, give us a call at (844) 438-7244. We're happy to help!
A1-081 Girodisc 2pc Front Brake Rotors
Girodisc A1-081 Girodisc 2pc Front Brake Rotors $950.00
FITMENT (FRONT): Ford Shelby GT500 (2007-12) Ford Mustang BOSS 302(S) Ford Mustang GT (2011-14 w/ Brembo calipers) Competition Motorsport is an authorized dealer for Girodisc products and we are one of the largest stocking dealers in the country.  We ship most products same or next business day to ensure we meet your delivery deadline. This Girodisc system is an upgrade to a two-piece steel rotor and aluminum hat combination as a direct replacement for the OEM brake discs.  The Girodisc floating rotors will bolt directly to your Mustang and work flawlessly with OEM calipers.  By upgrading your brakes with these lightweight high-performance replacements, as opposed to a big brake kit, your factory bias is maintained as well as your ABS effectiveness and efficiency.  The Girodisc rotors are lighter than OEM pieces, resuutling in a reduction in rotational and unsprung weight (4 lbs per corner) allowing for quicker acceleration, stronger braking, and faster suspension response. When used with Pagid or PFC performance brake pads, and Competition Motorsport RF-1 brake fluid, you have the best possible solution to overheating, cracking, and warping rotors. The central hat section of the disc is made from 6061-T6 aircraft specification aluminum.  The disc is manufactured from cast iron constructed in the USA, made to the same specification with the same material used by professional racing organizations.  The rotors' curved vane design was developed in racing and acts as a centrifugal pump to force cooling air through the disc.   The rotor and hat mount together through a floating mount system which utilizes ten high strength alloy steel drive pins manufactured by Girodisc in the USA to their own specifications and are cadmium plated for corrosion resistance.  The alloy drive pins transfer the load from the brake action while maintaining the axial and radial float between the disc rotor and hat.  The pins are secured by Grade-12 cap screws with hardened washers and mounted with anti-noise spring washers to allow for heat expansion while eliminating the rattle and noise associated with floating rotors. The two-piece Girodisc design allows for rotor only replacement as well to minimize future replacement costs and deliver outstanding performance and cooling. Sold/priced per pair.
Pagid Racing Brake Pads No. 8113
Pagid Pagid Racing Brake Pads No. 8113 $244.10
RSL 29: The PAGID RS29 (Yellow) is the world-leading endurance brake pad used by most of the winning teams in motorsport.  The racing compound combines the outstanding wear rate of the RS19 with a slightly higher coefficient of friction and initial bite. Based on the RS14, A slight reduction of the friction value improves the modulation (controllability). Nevertheless, the friction value is enough for cars without power-assisted brake system and ensures comfortable low effort on the brake pedal. Constant temperatures up to 600°C (1,100°F) are possible. This combination of friction value, fading stability and low wear rates on pads and discs (rotors) is unmatched. Due to its excellent release characteristics and controllability PAGID endurance materials are also often used for sprint races. Pagid RS29 with a very similar friction coefficient to RS19 with improvements in initial bite offering quicker response and slightly more temperature stable at the upper levels of the temperature range. Developments in raw material selection and compounding have resulted in improvements also in pedal feel and feedback, helping with modulation particularly on lighter applications. This material provides very good levels of performance and response at all temperature levels, only slight temperature inputs are required to bring the pad up to its optimum performance level. Another favourite with endurance racers having won many classes at all major endurance events, such as Le-Mans, Daytona, Spa, Nurburgring, etc. Due to the exceptional pad life and very low wear on brake discs it has been possible to run 24 hours without a change of pads or discs. Able to withstand slightly higher disc temperatures than RS19, this has proved more suitable for applications running very high disc temperatures. Although designed primarily for endurance racing, because of the consistent levels of performance and user friendliness many competitors use this material successfully for sprint and short distance races also. RS29 has also found favour in the growing track day market due to the level of control, good cold performance, long life and low disc wear.  
D2-081 Girodisc Rear Replacement Rotor Rings
Girodisc D2-081 Girodisc Rear Replacement Rotor Rings $550.00
FITMENT (REAR): Ford Shelby GT500 (2007-12) Ford Mustang BOSS 302(S) Ford Mustang GT (2011-14 w/ Brembo calipers) Competition Motorsport is an authorized dealer for Girodisc products and we are one of the largest stocking dealers in the country.  We ship most products same or next business day to ensure we meet your delivery deadline. REPLACEMENT ROTOR RINGS ONLY. Need new rings for your Girodisc two-piece rotors? We've got them. Replacement rings come complete with new hardware and full instructions for re-assembly. Or, if you like, you can send us the hats and we will do all the re-assembly for only the cost of shipping.  This service is available for the life of your rotors.Price is for a pair of rings and two hardware kits.
A2-081 Girodisc 2pc Rear Brake Rotors
Girodisc A2-081 Girodisc 2pc Rear Brake Rotors $850.00
FITMENT (REAR): Ford Shelby GT500 (2007-12) Ford Mustang BOSS 302(S) Ford Mustang GT (2011-14 w/ Brembo calipers) Competition Motorsport is an authorized dealer for Girodisc products and we are one of the largest stocking dealers in the country.  We ship most products same or next business day to ensure we meet your delivery deadline. This Girodisc system is an upgrade to a two-piece steel rotor and aluminum hat combination as a direct replacement for the OEM brake discs.  The Girodisc floating rotors will bolt directly to your Mustang and work flawlessly with OEM calipers.  By upgrading your brakes with these lightweight high-performance replacements, as opposed to a big brake kit, your factory bias is maintained as well as your ABS effectiveness and efficiency.  The Girodisc rotors are lighter than OEM pieces, resuutling in a reduction in rotational and unsprung weight (4 lbs per corner) allowing for quicker acceleration, stronger braking, and faster suspension response. When used with Pagid or PFC performance brake pads, and Competition Motorsport RF-1 brake fluid, you have the best possible solution to overheating, cracking, and warping rotors. The central hat section of the disc is made from 6061-T6 aircraft specification aluminum.  The disc is manufactured from cast iron constructed in the USA, made to the same specification with the same material used by professional racing organizations.  The rotors' curved vane design was developed in racing and acts as a centrifugal pump to force cooling air through the disc.   The rotor and hat mount together through a floating mount system which utilizes ten high strength alloy steel drive pins manufactured by Girodisc in the USA to their own specifications and are cadmium plated for corrosion resistance.  The alloy drive pins transfer the load from the brake action while maintaining the axial and radial float between the disc rotor and hat.  The pins are secured by Grade-12 cap screws with hardened washers and mounted with anti-noise spring washers to allow for heat expansion while eliminating the rattle and noise associated with floating rotors. The two-piece Girodisc design allows for rotor only replacement as well to minimize future replacement costs and deliver outstanding performance and cooling. Sold/priced per pair.
MP-1082-2 Girodisc Magic Pads (Rear)
Girodisc MP-1082-2 Girodisc Magic Pads (Rear) $85.00
GiroDisc "Magic Pads" are the solution to your squeaky, dusty, expensive factory replacement pads. They have lower dust than typical factory pads and much less than other performance pads. You won't be cleaning your wheels nearly as often! Additionally, they have great initial bite, something most less-expensive pads lack. But the real reason people like Magic Pads so much is they are the "silver bullet" to brake noise problems. Magic Pads are a semi-metallic composition that is easy on rotors and on your wallet. We recommend always replacing pads as a whole car set when switching compounds. All Magic Pads come with anti-noise shields pre-installed and included in the price. If you have any questions, give us a call at (844) 438-7244. We're happy to help!
D1-081 Girodisc Front Replacement Rotor Rings
Girodisc D1-081 Girodisc Front Replacement Rotor Rings $600.00
FITMENT (FRONT): Ford Shelby GT500 (2007-12) Ford Mustang BOSS 302(S) Ford Mustang GT (2011-14 w/ Brembo calipers) Competition Motorsport is an authorized dealer for Girodisc products and we are one of the largest stocking dealers in the country.  We ship most products same or next business day to ensure we meet your delivery deadline. REPLACEMENT ROTOR RINGS ONLY. Need new rings for your Girodisc two-piece rotors? We've got them. Replacement rings come complete with new hardware and full instructions for re-assembly. Or, if you like, you can send us the hats and we will do all the re-assembly for only the cost of shipping.  This service is available for the life of your rotors.Price is for a pair of rings and two hardware kits.