Murcielago (2002-04)

Lamborghini Murciélago Front Rotors Upgrade your Lamborghini Murciélago’s braking system with Girodisc 2-piece floating front rotors—precision-engineered to replace the OEM discs while maintaining perfect compatibility with your factory calipers. Designed for both street and track use, these rotors enhance cooling efficiency, reduce unsprung weight, and deliver sharper pedal response without compromising factory balance or ABS function. Each rotor features a 6061-T6 aluminum hat mated to Girodisc’s proprietary cast-iron rotor rings, both machined and assembled in-house in the USA. The 355mm rotors use a curved vane design that acts as a centrifugal pump, continuously drawing cool air through the disc to keep temperatures under control even during extended high-performance driving. Precision-Engineered Stopping Power for Your Murciélago Vehicle Fitment Lamborghini Murciélago (2002–2004) Designed for use with OEM front calipers Girodisc A1-098 Features Direct OEM replacement: Installs using factory calipers and hardware—no modifications required. 355mm diameter design: Provides improved brake torque and heat dissipation over stock rotors. Lightweight 2-piece construction: Approximately 24.5 lbs each vs. 27 lbs OEM for reduced unsprung mass. Curved vane ventilation: Internal vanes channel cooling air through the disc to reduce fade. Floating mount system: Allows for thermal expansion without distortion, maintaining even pad wear. Anti-noise hardware: Spring washers eliminate rattle while preserving proper float. Made in the USA: Fully cast, machined, and assembled domestically by Girodisc. Girodisc A1-098 FAQs Do these rotors fit the OEM Murciélago calipers? Yes. They bolt directly to the stock calipers without any modification. Are they lighter than the factory rotors? Yes. Each Girodisc rotor is about 2.5 lbs lighter, reducing unsprung and rotational mass. Do they improve braking performance? Absolutely. Expect better cooling, quicker heat recovery, and improved modulation under hard braking. Are these rotors suitable for street use? Yes. They perform flawlessly for both street driving and track conditions. How are they sold? Sold and priced per pair. Upgrade your Murciélago’s braking precision with Girodisc 355mm front rotors—built to handle supercar performance with unmatched control and reliability.

Girodisc Lamborghini Murciélago ('02–'04) 335mm Rear Rotors Enhance the stopping power of your early-generation Lamborghini Murciélago with Girodisc’s lightweight two-piece rear rotors. Engineered for precision and durability, these rotors provide superior cooling and responsiveness while maintaining OEM fit, brake bias, and ABS performance. Perfect for drivers who demand world-class braking without the weight penalty. Vehicle Fitment Lamborghini Murciélago (2002–2004)335mm rear rotor applicationDirect replacement for OEM rear rotors using factory calipers and hardware. Performance and Craftsmanship in Every Detail The Girodisc system installs directly onto factory hubs—no modifications required. Each rotor features a 6061-T6 aluminum hat paired with Girodisc’s proprietary cast-iron friction ring, both made and machined in the USA. The floating two-piece design allows the rotor to expand under heat without warping, maintaining consistent pedal feel and pad contact. Curved internal vanes act as centrifugal pumps, drawing air through the disc to keep braking temperatures stable. With a weight savings of nearly 4 pounds per rotor, these units improve acceleration and suspension response while reducing thermal stress. Features • Direct OEM replacement—no adapters or modifications required• 6061-T6 billet aluminum hats with hard-anodized finish• Proprietary cast-iron friction rings, poured and machined in the USA• Floating mount system with 10 cadmium-plated steel drive pins• Anti-noise spring washers prevent rattle while maintaining float• Curved vane internal design enhances cooling efficiency• Approximately 18.2 lbs vs. 22 lbs OEM – saves nearly 4 lbs per rotor• Fully rebuildable—replace only the iron rings when worn• Sold/priced per pair Girodisc A2-098 Rear Rotor FAQs: Are these rotors a direct fit for my 2002–2004 Murciélago? Yes. They bolt directly to the factory hubs and work seamlessly with OEM calipers and hardware—no changes required. How much lighter are these than stock rotors? Each Girodisc rear rotor weighs about 18.2 lbs compared to the factory’s 22 lbs, saving roughly 4 lbs per corner in unsprung weight. Will these affect my car’s ABS or traction systems? No. Girodisc rotors preserve OEM geometry and weight distribution, maintaining full compatibility with factory systems. Are these suitable for high-performance driving? Absolutely. Designed using motorsport principles, these rotors deliver consistent braking performance under repeated high-temperature conditions. Upgrade your Lamborghini Murciélago with Girodisc rear rotors—precision-engineered for reduced weight, superior cooling, and confidence-inspiring braking control.

Pagid Racing Brake Pads No. 1287 Fits the Following Vehicles Make Model Build (Year) Front Rear Audi R8 4.2 and 5.2 FSI quattro 07 - 15 X Audi R8 4.2 and 5.2 FSI quattro [ceramic brakes] 09 - 15 X Audi R8 5.2 FSI quattro (2nd generation) 15 - X Audi R8 5.2 FSI quattro (2nd generation) [ceramic brakes] 15 - X Audi R8 5.2 RWS (2nd generation) 18 - X BMW M2 [F87] Competition 18 - 19 X BMW M4 [F82] [ceramic brakes] 14 - X BMW M2 CS Racing [Permit B 365PS] 20 - X BMW M2 CS Racing [Permit B 365PS] 2020 X BMW M3 [F80] [ceramic brakes] 14-18 X Ferrari F40 Street and race 87 - 92 X Ferrari F50 95 - 97 X Lamborghini Diablo [Brembo brakes] 92 - 99 X Lamborghini Gallardo 04 - 13 X Lamborghini Gallardo [ceramic brakes] 04 - 13 X Lamborghini Huracán [iron brakes] 14 - X Lamborghini Huracán and Performance [ceramic brakes] 14 - X Lamborghini Murciélago [non ceramic] 01 - 10 X McLaren F1 / shape rear on inquiry 92 - 98 X Nissan R35 GTR 08 - X RSL 29 Compound: The Pagid RSL 29 (Yellow) is the world-leading endurance brake pad used by most of the winning teams in motorsport. Although designed primarily for endurance racing, many competitors use this material successfully for sprint and short distance races also. RS29 has also found favor in the growing track day market due to the level of control, good cold performance, long life and low disc wear. Pagid RSL 1 Compound Used in GT cars, touring cars and prototype endurance racing. Due to the high friction and good modulation, often used in sprint races as well. RSL 1 is a low metallic resin bonded material containing steel and aramid fibers with very high heat resistance. It maintains a constant friction level over a wide range of temperatures. Its reduced wear rate and disc friendliness make this material appropriate for endurance races. RS 14 Compound: The Pagid RS 14 (Black) is a high friction value ceramic compound with very good modulation and high fade resistance. A very popular, aggressive pad with strong initial bite and high torque. In addition to the track-day environment, RS14 has shown success in short- to medium-distance circuit racing as well as gravel and tarmac rallying. Pagid RSC 1 Compound (Ceramic Rotors Only) A race and track day compound for all known types of ceramic brake discs, RSC 1 is a low metallic resin bonded material containing steel and aramid fibers. This material features good all-round characteristics and is suitable for all types of usage. Pagid RSC 3 Compound (Ceramic Rotors Only) RSC 3 is a low metallic resin bonded material containing steel fibers. This material is specifically developed for above mentioned applications. It is a special race compound for ceramic discs with low content of fibers in the friction surface for sprint and endurance circuit racing. Pagid RST 1 Compound Used in Rally tarmac, GT cars and touring cars circuit racing (sprint), high down-force formula cars, NASCAR. Suitable for applications in heavy cars and where high torque is necessary against small diameter rotors. RST 1 has a very high friction level and high temperature resistance. It is a semi-metallic resin bonded material containing steel fibers. Cold friction and initial bite makes this material most appropriate for Rally and NASCAR applications. Pagid RST 2E Compound: RST 2E is perfect as a front axle application in mid-endurance GT and touring car racing, in the range of 2-6h race duration. Front and rear axle application on rally race cars. RST 2 and RST 2E are semi-metallic resin bonded materials containing steel fibers. Cold friction and initial bite make these materials most appropriate for rallying and NASCAR applications. Pagid RST 3 Compound: RST 3 is a medium-high friction metal-ceramic compound containing steel fibers and is therefore the perfect complement of the RST product family. It captivates by its low heat conductivity. Rally tarmac and gravel, GT cars, touring cars and prototype circuit racing, formula cars and club racing. Wide range of applications due to it‘s combination of bite, friction and controllability. Pagid RST 4 Compound: RST 4 is a semi-metallic resin bonded material containing steel fibers. This material has a medium friction level and high temperature resistance. Typically use is in formula cars and open wheel racing. It is also very popular as a rear-axle material for rally racing (tarmac and gravel) and for front engine cars. Also used in NASCAR on long ovals.

Pagid Racing Brake Pads No. 1287 Fits the Following Vehicles Make Model Build (Year) Front Rear Aston Martin Vanquish 03 - 08 X Dodge Viper Competition Coupe 03 - X Dodge Viper SRT-10 04 - 08 X Ferrari 512 Testarossa 92 - 96 X Ferrari F40 Street and race 87 - 92 X Ferrari F50 95 - 97 X Lamborghini Diablo [Brembo brakes] 92 - 99 X Lamborghini Murciélago [non ceramic] 01 - 10 X McLaren F1 / shape rear on inquiry 92 - 98 X RSL 29 Compound: The Pagid RSL 29 (Yellow) is the world-leading endurance brake pad used by most of the winning teams in motorsport. Although designed primarily for endurance racing, many competitors use this material successfully for sprint and short distance races also. RS29 has also found favor in the growing track day market due to the level of control, good cold performance, long life and low disc wear. Pagid RSL 1 Compound Used in GT cars, touring cars and prototype endurance racing. Due to the high friction and good modulation, often used in sprint races as well. RSL 1 is a low metallic resin bonded material containing steel and aramid fibers with very high heat resistance. It maintains a constant friction level over a wide range of temperatures. Its reduced wear rate and disc friendliness make this material appropriate for endurance races. RS 14 Compound: The Pagid RS 14 (Black) is a high friction value ceramic compound with very good modulation and high fade resistance. A very popular, aggressive pad with strong initial bite and high torque. In addition to the track-day environment, RS14 has shown success in short- to medium-distance circuit racing as well as gravel and tarmac rallying. Pagid RSC 1 Compound (Ceramic Rotors Only) A race and track day compound for all known types of ceramic brake discs, RSC 1 is a low metallic resin bonded material containing steel and aramid fibers. This material features good all-round characteristics and is suitable for all types of usage. Pagid RSC 3 Compound (Ceramic Rotors Only) RSC 3 is a low metallic resin bonded material containing steel fibers. This material is specifically developed for above mentioned applications. It is a special race compound for ceramic discs with low content of fibers in the friction surface for sprint and endurance circuit racing. Pagid RST 1 Compound Used in Rally tarmac, GT cars and touring cars circuit racing (sprint), high down-force formula cars, NASCAR. Suitable for applications in heavy cars and where high torque is necessary against small diameter rotors. RST 1 has a very high friction level and high temperature resistance. It is a semi-metallic resin bonded material containing steel fibers. Cold friction and initial bite makes this material most appropriate for Rally and NASCAR applications. Pagid RST 2E Compound: RST 2E is perfect as a front axle application in mid-endurance GT and touring car racing, in the range of 2-6h race duration. Front and rear axle application on rally race cars. RST 2 and RST 2E are semi-metallic resin bonded materials containing steel fibers. Cold friction and initial bite make these materials most appropriate for rallying and NASCAR applications. Pagid RST 3 Compound: RST 3 is a medium-high friction metal-ceramic compound containing steel fibers and is therefore the perfect complement of the RST product family. It captivates by its low heat conductivity. Rally tarmac and gravel, GT cars, touring cars and prototype circuit racing, formula cars and club racing. Wide range of applications due to it‘s combination of bite, friction and controllability. Pagid RST 4 Compound: RST 4 is a semi-metallic resin bonded material containing steel fibers. This material has a medium friction level and high temperature resistance. Typically use is in formula cars and open wheel racing. It is also very popular as a rear-axle material for rally racing (tarmac and gravel) and for front engine cars. Also used in NASCAR on long ovals.

Girodisc Brake Pad Spreader The Right Tool for the Job This indispensable tool is used by race teams, shops, and enthusiasts alike who have high performance four- and six-piston calipers. The Girodisc Brake Pad Spreader is designed to easily spread brake pads and pistons to facilitate quick replacement of pads and/or rotors in a shop or racing environment. No more screwdrivers, pliers, hammers, or C-clamps! This tool will retract the pistons fully and evenly into their bores with one squeeze of the levers. The Girodisc Brake Pad Spreader was designed to be used with popular racing brake calipers from Brembo, AP Racing, Alcon, and other performance calipers in racing and road use. To help it fit into any caliper, the amount of throw is adjustable. Built Like a Tank. Works Like a Charm. Insert the spreading plates one way for wider six-piston calipers, or turn the spreader 90o and use the plate sides for four-piston calipers. The Girodisc Brake Pad Spreader is made from heavy-gauge steel, powder-coated for durability. The slider is cadmium-plated, and nylon pivot bushings ensure smooth action. It will quickly become an invaluable tool for any race team, shop, or enthusiast who changes pads and rotors frequently.

CMS Performance RF1 DOT4 Racing Brake Fluid Real Life 622º Boiling Point Without the Real High Price RF1 Racing Brake Fluid from CMS Performance is a fully-synthetic DOT4 brake fluid formulated to provide extraordinary performance under the most demanding high-temperature racing and track-day conditions. With a dry boiling point of 622º F / 328º C, RF1 exceeds all DOT 3 & DOT 4 requirements and is compatible with all DOT 3, DOT 4, and DOT 5.1 fluids. Note: RF1, like all DOT 4 brake fluids, is not compatible with DOT 5 silicone-based or any mineral-based brake fluids. On the race track, there is perhaps no single safety system more important than your brakes. No single part of that system is more critical than brake fluid, given the extraordinarily high temperatures it operates under. At CMS Performance, we got tired of (and a little nervous) using "racing" brake fluid at the race track that didn't live up to its claimed performance when things got hot. We found more than a few brands whose product was all hype and not high performance. No Hype. All Performance. No Kidding. So we did something about it. CMS Performance RF1 is manufactured in partnership with Orthene, maker of the also-excellent Halo P1 racing brake fluid and a brake fluid supplier to many racing teams in Formula 1, WEC, and other professional series. RF1 was formulated to maintain consistent viscosity, lubricity, and compressibility at the extreme system temperatures and line pressures found in racing and track days. The bottom line is this: you can spend a lot more on brake fluid, but it's hard to find higher-performance than RF1 Racing Brake Fluid. CMS Performance RF1 Racing Brake Fluid Details: Manufacturer: CMS Performance Manufacturer part no.: CMSRF1 Typical dry boiling point: 622º F / 328º C Typical wet boiling point: 399º F / 204º C Exceeds DOT 3 & DOT 4 standards Bottle size: 500 ml (16.9 fl. oz.) Click Here for Product MSDS Sheet A Word About Flushing Brake Fluid All brake fluid degrades over time (not mileage), attracting water as it ages, which, at high brake temperatures, can lead to fluid boil and brake fade or failure. That's why the "wet" (aged) boiling point of any brake fluid is substantially lower than the "dry" (new) boiling point. To maintain maximum braking performance, Competition Motorsport strongly suggests replacing your brake fluid before every track event, but at least every three months if you're consistently racing and/or driving at track days. It's cheap insurance against learning about brake fade the hard way!