The best highest performance racing brake fluid on the market today is CMS Performance RF1 with a dry boiling point of 622ºF!
Competition Motorsport CMS Performance RF1 DOT4 Racing Brake Fluid (500 ml) from $24.95
CMS Performance RF1 DOT4 622oF Racing Brake Fluid Buy in bulk and save. Get six bottles and save 15%, or a case of 12 and save a whopping 25%! The Highest Dry Boiling Point Racing Brake Fluid You Can Buy CMS Performance RF1 fully synthetic Racing Brake Fluid is formulated to provide the highest performance under racing and track-day conditions, where braking systems operate at very high sustained temperatures. RF1 exceeds all DOT 3 & 4 requirements and is compatible with all DOT 3, 4, and 5.1 fluids. (Not compatible with DOT5 or mineral-based brake fluids.) There is perhaps no single safety system more important in racing than brakes. And no part of that system is more critical than brake fluid. At Competition Motorsport, we got tired of (and a little nervous) using "racing" brake fluid on the track that didn't live up to its claimed performance. So we did something about it. Manufactured in partnership with Orthene Chemicals, a British brake fluid supplier to professional race teams in Formula 1, WEC, and many other pro series, CMS Performance RF1 Racing Brake Fluid is formulated to maintain consistent viscosity, lubricity, and compressibility at extreme temperatures and line pressures found in racing, track days, and spirited driving. Bottom line: you can spend more money, but you can't buy higher-performing racing brake fluid! CMS Performance RF1 Racing Brake Fluid Specifications: Typical dry boiling point: 622° F (328° C) Typical wet boiling point: 399° F (204° C) Exceeds DOT3 & DOT4 standards Individual 500 ml (16.7 oz.) bottles Click Here For The RF1 Product MSDS Sheet A Note About Brake Fluid Boiling Points DOT 4 brake fluid like RF1 is hygroscopic, meaning it attracts water over time sitting in your brake lines and reservoir. At high brake temperatures, this water can boil in your car's brake lines, causing the fluid in the lines to become compressible. That's what you feel when you experience brake fade. This is why the "wet" (aged fluid) boiling point of any brake fluid is substantially lower than the "dry" (brand new fluid) boiling point. Since time is the enemy of brake fluid performance, the best practice is to replace your racing brake fluid before each track event/weekend. At a minimum, flush it with new fluid at least every three months if you're consistently racing and/or driving at track days. A couple bottles of fluid will flush most sports cars or race cars. It ends up being pretty cheap insurance against learning about brake fade the hard way.
Girodisc Pad Spreader GDPS01
Girodisc Girodisc Pad Spreader GDPS01 $250.00
Girodisc Brake Pad Spreader This indispensable tool is used by race teams, shops, and enthusiasts alike who have high performance four- and six-piston calipers. The spreader is designed to spread brake pads and pistons in four- and six-piston calipers to facilitate quick replacement of pads and/or rotors in a shop or racing environment.No more screwdrivers, pliers, hammers, or C-clamps! This tool will retract the pistons evenly and all the way back into their bores with one squeeze of the levers. The Girodisc spreader was designed around popular four-piston and six-piston calipers from Brembo, AP Racing, Alcon, and other performance calipers in racing and road use. To help fit in any caliper, the amount of throw is adjustable.Insert the spreading plates one way for wider six-piston calipers, then turn the spreader 90o and use the plate sides for four-piston calipers.The Girodisc Pad Spreader is made from heavy-gauge steel and is powder-coated for durability. The slider is cadmium-plated, and nylon pivot bushings ensure smooth action. The Girodisc Pad Spreader will quickly become an invaluable tool for any race team, shop, or enthusiast who changes pads and rotors with any frequency.
Pagid Racing Brake Pads No. 2487
Pagid Pagid Racing Brake Pads No. 2487 from $360.95
 Fits These Vehicles: Make Model Build (Year) Front Rear Alfa Romeo Giulia 2.9 [952] 15 -   X Aston Martin DB 9 04 - X   Aston Martin Vantage V8 GT4 ProDrive [race car] 12 - X   Audi RS3 Sportback [8PA] 11 - 12 X   Audi TT RS 2.5 Quattro 09 - 14 X   Cadillac CTS-V (4 piston front caliper) 03 - 09 X   Chevrolet Camaro SS 09 - 15 X   Chevrolet Camaro SS - 4 Piston Brembo caliper 16 - X   Chevrolet Corvette Brembo 6 piston non ceramic 09 -   X Chevrolet Corvette C7 base 14 - X   Chevrolet Corvette C7 Z51 14 - X   Dodge Viper SRT TA (time attack) 14 - X X Ford GT 04 - 06 X X Ford Mustang Boss 302 12 - 13 X   Ford Mustang GT [4 piston Brembo] 15 - X   Ford Mustang Shelby GT500 [4 piston Brembo caliper / 15" disc] 07 - 14 X   Honda (Acura) Acura TL 04 - X   Honda (Acura) Civic IX Type R [Brembo brakes] 15 - X   Hyundai Genesis Coupe 3.8 track 10 - X   Maserati Ghibli (M157) [4 piston Brembo caliper / disc ø 345mm] 13 - X   Mitsubishi Lancer Evo V - Evo IX 98 - 06 X   Mitsubishi Lancer Evo X 07 - 16 X   Renault Mégane III 2.0 RS [Brembo brakes] without electronic hand brake 08 - X   Subaru STI 3rd & 4th generation 03 - 16 X   Volvo S60 Turbo R Brembo brakes 03 - X   Volvo V70 R 2.5T Brembo brakes 03 - X   RSL 29: The PAGID RS29 (Yellow) is the world-leading endurance brake pad used by most of the winning teams in motorsport. Although designed primarily for endurance racing, many competitors use this material successfully for sprint and short distance races also. RS29 has also found favor in the growing track day market due to the level of control, good cold performance, long life and low disc wear. RS 14: The PAGID RS14 (Black) is a high friction value ceramic compound with very good modulation and high fade resistance. A very popular, aggressive pad with strong initial bite and high torque. In addition to the track-day environment, RS14 has shown success in short- to medium-distance circuit racing as well as gravel and tarmac rallying. RSL1: PAGID RSL1 has a high ceramic content with superior thermal insulation and higher heat resistance than metallic pad compounds. They feature excellent pad wear under endurance conditions, excellent rotor life, and are less aggressive than RST pads with excellent brake balance and modulation.
Pagid Racing Brake Pads No. 1408
Pagid Pagid Racing Brake Pads No. 1408 from $276.89
  Fits These Vehicles: Make Model Build (Year) Front Rear Aston Martin DB 9 04 -   X Aston Martin Vanquish 03 - 08   X Aston Martin Vantage V8 GT4 ProDrive [race car] 12 -   X Cadillac CTS-V (4 piston front caliper) 03 - 09   X Cadillac CTS-V (6 piston front caliper) 10 -   X Chevrolet Camaro SS 09 - 15   X Chevrolet Camaro ZL1 12 - 15   X Dodge Viper 92 - 00 X   Dodge Viper 01 - 02 X   Ferrari 360 all models 99 - 05 X X Ferrari F430 [cast iron brakes] 05 - 10 X X KTM X-Bow 08 - X   Lancia Delta 2.0 HF Int.16V Evo 91 - 94 X   Lotus Esprit Turbo 94 - 96 X X Maserati Ghibli (M157) [6 piston Brembo caliper / disc ø 360mm] 13 -   X Maserati Grand Turismo 07 -   X Peugeot 406 Coupe Brembo brake 97 - 04 X   Renault Clio II 3.0 V6 mid engine 00 - 05 X X Seat Leon 1.8T Cupra R (Brembo) 03 - 06 X   Seat Leon 2.8 Cupra 4 (Brembo) 01 - 06 X   Volvo S60 Turbo R Brembo brakes 03 -   X Volvo V70 R 2.5T Brembo brakes 03 -   X   RSL 29: The PAGID RS29 (Yellow) is the world-leading endurance brake pad used by most of the winning teams in motorsport. Although designed primarily for endurance racing, many competitors use this material successfully for sprint and short distance races also. RS29 has also found favor in the growing track day market due to the level of control, good cold performance, long life and low disc wear. RS 14: The PAGID RS14 (Black) is a high friction value ceramic compound with very good modulation and high fade resistance. A very popular, aggressive pad with strong initial bite and high torque. In addition to the track-day environment, RS14 has shown success in short- to medium-distance circuit racing as well as gravel and tarmac rallying. RS 42: The PAGID RS42 (Blue) is a carbon based compound with a medium friction level. It has excellent low-temperature response and is a very user-friendly compound with excellent modulation and feel. It is used across many forms of motorsport from single seaters, through sports car racing, to Group N rallying on gravel and wet tarmac surfaces. RSL 1: Used in GT cars, Touring cars and prototype endurance racing. Due to the high friction and good modulation, often used in sprint races as well.RSL 1 is a low metallic resin bonded material containing steel and aramid fibers with high heat resistance. It maintains a constant friction level over a wide range of temperatures. Its low wear rate and disc friendliness make this material appropriate for endurance races.  
A2-211 Girodisc 2pc Rear Brake Rotors (ZL1 Gen 6)
Girodisc A2-211 Girodisc 2pc Rear Brake Rotors (ZL1 Gen 6) $1,100.00
Competition Motorsport is an authorized dealer for Girodisc products. As one of the largest stocking dealers in the country, we ship most Girodisc products the same or next business day to ensure we meet your delivery deadline. Fits Chevrolet Camaro ZL1 Gen 6 These Girodisc iron rotors are a direct replacement for the OE brake discs with no modifications. The central hat section of the Girodisc rotor is made from strictly USA-sourced 6061-T6 aircraft specification aluminum. The disc is made from Girodisc's own proprietary cast iron, poured in the USA and machined from start to finish in house at Girodisc. The rotor utilizes a curved-vane design, developed in racing to act as a centrifugal pump forcing cool air through the disc. The disc and hat have a floating mount system, which utilizes 12 high-strength alloy steel drive pins, manufactured in the US by Girodisc and cadmium plated for long-lasting corrosion resistance. These pins take the loads from braking while maintaining the axial and radial float between the hat and disc. They are secured by class 12.9 cap screws and hardened washers. In order to keep the rotors from making noise when cold, the pins are mounted with anti-noise springs on the disc side, allowing the iron disc to expand as it heats up while eliminating the rattle and noise commonly associated with floating rotors. This float also allows the rotor to self center between the brake pads. Once the Girodisc system is in place, you simply replace the cast iron discs when needed. This reduces cost over time by allowing you to re-use the aluminum central hats. Sold/priced per pair
Goodridge G-Stop Stainless Brake Lines Camaro SS (2010+)
Goodridge Goodridge G-Stop Stainless Brake Lines Camaro SS (2010+) $199.00
Goodridge G-Stop High Performance Stainless Brake Lines This Kit For: Camaro SS w/o Brembo (2010+) Goodridge G-Stop high performance brake lines for your Camaro consist of the finest quality PTFE inner hose covered by a braided stainless steel outer casing. This gives you a much firmer, more responsive brake pedal by eliminating the “spongy” feel that often accompanies stock rubber brake lines, making them ideal for the very high brake pressures seen during HPDE track days. G-Stop High Performance Brake lines are abrasion and corrosion resistant so they last a long time under harsh conditions. Goodridge G-Stop high performance brake lines are direct bolt-on replacements for all of the rubber brake lines in your Camaro's brake system. Four brake lines are included in each kit, with hose ends and brake line brackets that match the car’s original equipment.  Conforming to Federal Motor Vehicle Safety Standard Number 106, Goodridge G-Stop high performance brake lines are U.S. DOT certified and T.U.V. approved. All Goodridge G-Stop brake lines go through a nine-point Quality Assurance testing process that includes measuring tensile strength and the ability to sustain line pressures to 3,000 psi. Features: Precise fit for your Camaro Greater braking efficiency Resistance to abrasion and corrosion Firmer pedal under heavy braking Added reliability, safety and brilliant looks Technically superior and race proven DOT, TUV, ADR, DEKRA, ARAICCC, ISO9001 Accredited. FMVSS 106 compliant, DOT approved   Brake components should be installed by a competent mechanic in a professional manner.  Incorrect installation of brake components can cause a major safety problem or an accident.
D2-173 Girodisc Rear Rotor Ring Replacements
Girodisc D2-173 Girodisc Rear Rotor Ring Replacements $700.00
REPLACEMENT ROTOR RINGS ONLY. INCLUDES NEW INSTALLATION HARDWARE. DOES NOT INCLUDE ALUMINUM HATS. Competition Motorsport is an authorized dealer for Girodisc products. As one of the largest stocking dealers in the country, we ship most Girodisc products the same or next business day to ensure we meet your delivery deadline. These Girodisc replacement rotor rings are direct replacements for the iron discs on your Girodisc two-piece rotors, and no modifications are necessary. New cap screws and washers are included with these replacement rotors. We do not recommend re-using the old hardware. The replacement rotor rings and hat mount together through a floating mount system which utilizes 8-10 high strength alloy steel drive pins manufactured by Girodisc in the USA to their own specifications and are cadmium plated for corrosion resistance. The alloy drive pins transfer the load from the brake action while maintaining the axial and radial float between the disc rotor and hat. The pins are secured by grade 12 cap screws with hardened washers and mounted with anti-noise spring washers to allow for heat expansion while eliminating the rattle and noise associated with floating rotors. The two-piece Girodisc design allows for rotor ring-only replacement to minimize replacement costs and deliver outstanding performance and cooling. Sold/priced per pair.
D1-039 Girodisc Front Replacement Rotor Rings (Camaro 2010-2015)
Girodisc D1-039 Girodisc Front Replacement Rotor Rings (Camaro 2010-2015) $600.00
REPLACEMENT ROTOR DISCS ONLY, DOES NOT INCLUDE ALUMINUM HAT. Competition Motorsport is an Authorized dealer for GiroDisc products and we are one of the largest stocking dealers in the country.  We ship most products same or next business day to ensure we meet your delivery deadline. The GiroDisc replacement rotor system is a direct rotor disc replacement for the GiroDisc 2-piece hat and rotor and no modifications are necessary.   The rotor and hat mount together through a floating mount system which utilizes 8-10 high strength alloy steel drive pins manufactured by GiroDisc in the USA to our own specifications and are cadmium plated for corrosion resistance.  The alloy drive pins transfer the load from the brake action while maintaining the axial and radial float between the disc rotor and hat.  The pins are secured by grade 12 cap screws with hardened washers and mounted with anti-noise spring washers to allow for heat expansion while eliminating the rattle and noise associated with floating rotors. The 2-piece GiroDisc design allows for rotor only replacement to minimize replacement costs and deliver outstanding performance and cooling. Sold/Priced per pair.
A1-039 Girodisc 2pc Front Brake Rotors (Camaro 2010-2015)
Girodisc A1-039 Girodisc 2pc Front Brake Rotors (Camaro 2010-2015) $1,100.00
FITS: Chevy Camaro Gen 5 front (2010-2015) Competition Motorsport is an authorized dealer for Girodisc products. As one of the largest stocking dealers in the country, we ship most products the same or next business day to ensure we meet your delivery deadline.This Girodisc system upgrades the OEM brakes to a two-piece steel disc and aluminum hat. This two-piece "floating rotor" design will bolt directly to your Gen 5 Camaro front and work flawlessly with the OEM calipers.Upgrading your brakes to lightweight, high-performance Girodisc rotors, you maintain the factory brake bias and ABS effectiveness. Much lighter than the OEM rotors, Girodisc rotors reduce rotational and unsprung mass giving you stronger braking and faster suspension response.Combined with Pagid or PFC performance brake pads and Competition Motorsport RF-1 racing brake fluid, Girodisc rotors are the ultimate solution to overheated, cracked, warped rotors that result from high-performance driving.The central hat of the rotor is made from 6061-T6 aircraft aluminum. The disc is manufactured in the USA from the same cast iron used by professional racing organizations. Its curved-vane design, developed in racing, acts like a centrifugal pump forcing cool air through the disc.The disc and hat mount together through a floating mount system using ten cadmium plated, high-strength alloy steel drive pins manufactured by Girodisc. These drive pins transfer braking load while maintaining axial and radial float between the disc and hat to allow for heat expansion. Anti-noise spring washers eliminate the noise typically associated with floating rotors.This two-piece Girodisc design allows for disc-only replacement, reusing the hat to minimize maintenance costs.Sold/priced per pair.