The best highest performance racing brake fluid on the market today is CMS Performance RF1 with a dry boiling point of 622ºF!
Competition Motorsport CMS Performance RF1 DOT4 Racing Brake Fluid (500 ml) from $24.95
CMS Performance RF1 DOT4 622oF Racing Brake Fluid Buy in bulk and save. Get six bottles and save 15%, or a case of 12 and save a whopping 25%! The Highest Dry Boiling Point Racing Brake Fluid You Can Buy CMS Performance RF1 fully synthetic Racing Brake Fluid is formulated to provide the highest performance under racing and track-day conditions, where braking systems operate at very high sustained temperatures. RF1 exceeds all DOT 3 & 4 requirements and is compatible with all DOT 3, 4, and 5.1 fluids. (Not compatible with DOT5 or mineral-based brake fluids.) There is perhaps no single safety system more important in racing than brakes. And no part of that system is more critical than brake fluid. At Competition Motorsport, we got tired of (and a little nervous) using "racing" brake fluid on the track that didn't live up to its claimed performance. So we did something about it. Manufactured in partnership with Orthene Chemicals, a British brake fluid supplier to professional race teams in Formula 1, WEC, and many other pro series, CMS Performance RF1 Racing Brake Fluid is formulated to maintain consistent viscosity, lubricity, and compressibility at extreme temperatures and line pressures found in racing, track days, and spirited driving. Bottom line: you can spend more money, but you can't buy higher-performing racing brake fluid! CMS Performance RF1 Racing Brake Fluid Specifications: Typical dry boiling point: 622° F (328° C) Typical wet boiling point: 399° F (204° C) Exceeds DOT3 & DOT4 standards Individual 500 ml (16.7 oz.) bottles Click Here For The RF1 Product MSDS Sheet A Note About Brake Fluid Boiling Points DOT 4 brake fluid like RF1 is hygroscopic, meaning it attracts water over time sitting in your brake lines and reservoir. At high brake temperatures, this water can boil in your car's brake lines, causing the fluid in the lines to become compressible. That's what you feel when you experience brake fade. This is why the "wet" (aged fluid) boiling point of any brake fluid is substantially lower than the "dry" (brand new fluid) boiling point. Since time is the enemy of brake fluid performance, the best practice is to replace your racing brake fluid before each track event/weekend. At a minimum, flush it with new fluid at least every three months if you're consistently racing and/or driving at track days. A couple bottles of fluid will flush most sports cars or race cars. It ends up being pretty cheap insurance against learning about brake fade the hard way.
Girodisc Pad Spreader GDPS01
Girodisc Girodisc Pad Spreader GDPS01 $250.00
Girodisc Brake Pad Spreader This indispensable tool is used by race teams, shops, and enthusiasts alike who have high performance four- and six-piston calipers. The spreader is designed to spread brake pads and pistons in four- and six-piston calipers to facilitate quick replacement of pads and/or rotors in a shop or racing environment.No more screwdrivers, pliers, hammers, or C-clamps! This tool will retract the pistons evenly and all the way back into their bores with one squeeze of the levers. The Girodisc spreader was designed around popular four-piston and six-piston calipers from Brembo, AP Racing, Alcon, and other performance calipers in racing and road use. To help fit in any caliper, the amount of throw is adjustable.Insert the spreading plates one way for wider six-piston calipers, then turn the spreader 90o and use the plate sides for four-piston calipers.The Girodisc Pad Spreader is made from heavy-gauge steel and is powder-coated for durability. The slider is cadmium-plated, and nylon pivot bushings ensure smooth action. The Girodisc Pad Spreader will quickly become an invaluable tool for any race team, shop, or enthusiast who changes pads and rotors with any frequency.
Pagid Racing Brake Pads No. 8269
Pagid Pagid Racing Brake Pads No. 8269 $1,002.15
Fits These Vehicles: Make Model Build (Year) Front Rear McLaren 720S [ceramic brakes] 2018 + X   McLaren 600LT [ceramic brakes] 2019 + X RSC 1: The Pagid RSC1 is a good street/track compromise for enthusiasts with Carbon-Ceramic Brakes. Used for sprint racing and track days compound with all known types of ceramic brake discs. An ideal combination of cold friction, fade resistance and low thermal oxidation of the disc surface.
A2-159 Girodisc 2pc Rear Brake Rotors (McLaren 570 - 650S - 600LT - 720S)
Girodisc A2-159 Girodisc 2pc Rear Brake Rotors (McLaren 570 - 650S - 600LT - 720S) $1,800.00
FITMENT (REAR): McLaren 650S McLaren 570S McLaren 720S McLaren 600LT Competition Motorsport is an authorized dealer for Girodisc products and we are one of the largest stocking dealers in the country.  We ship most Girodisc systems the same or next business day to ensure we meet your delivery deadline. The Girodisc system for the McLaren 600LT, 720S, 650S or 570S is a direct replacement for the OEM carbon ceramic rotors. No modifications are necessary, the Girodisc rotors will bolt directly to your McLaren and work with the original calipers without issue.  We recommend Pagid 4346 racing brake pads for this Girodisc system, in either RS29 (endurance) or RS14 (sprint) compound. The central hat section of the disc is made from 6061-T6 aircraft specification aluminum.  The disc is made from cast iron to the same specification and material as used by professional racing organizations. It is a curved vane design, developed in racing to act as a centrifugal pump to force cooling air through the disc.The rotor and hat have a floating mount system, which utilizes 10 high strength alloy steel drive pins, manufactured by Girodisc to our own specifications and cadmium plated for a long lasting corrosion resistance. These pins take the load from braking actions while maintaining the axial and radial float between the hat and disc. In order to keep the rotors from making noise when cold, the pins are mounted with anti-noise spring washers on the rotor side which allow the rotor to grow with heat expansion but eliminate the rattle and noise associated with floating rotors. This float also allows the rotor to self center between the pads.Once the Girodisc system is in place, simply replace the cast iron rotor when needed. When used with Pagid pads and high-temp racing brake fluid, you have a truly amazing, race-proven solution to the fragile, ultra-expensive carbon-ceramic rotors on your McLaren.
A1-206 Girodisc 2pc Front Brake Rotors (McLaren 600LT - 720S)
Girodisc A1-206 Girodisc 2pc Front Brake Rotors (McLaren 600LT - 720S) $1,900.00
FITS: MCLAREN 720S (CCB Rotor) The Girodisc system is a direct replacement for the OE CCB disc on all vehicles that came equipped with CCB rotors from the factory. The central hat section of the disc is made from 6061-T6 aircraft specification aluminum. The disc is made from cast iron to the same specification and material as used by professional racing organizations. It is a curved vane design, developed in racing to act as a centrifugal pump to force cooling air through the disc.The rotor and hat have a floating mount system, which utilizes 10 high strength alloy steel drive pins, manufactured by Girodisc to our own specifications and cadmium plated for a long lasting corrosion resistance. These pins take the load from braking actions while maintaining the axial and radial float between the hat and disc. In order to keep the rotors from making noise when cold, the pins are mounted with anti-noise spring washers on the rotor side which allow the rotor to grow with heat expansion but eliminate the rattle and noise associated with floating rotors. This float also allows the rotor to self center between the pads.Once the Girodisc system is in place, simply replace the cast iron rotor when needed. When used with performance pads and hi-temp fluid, you have what amounts to a truly amazing solution to overheating or warping rotors. Sold/Priced per pair.
Pagid Racing Brake Pads No. 8270
Pagid Pagid Racing Brake Pads No. 8270 $674.40
Fits These Vehicles: Make Model Build (Year) Front Rear McLaren 720S [ceramic brakes] 2018 +  X McLaren 600LT [ceramic brakes] 2019 +   RSC 1: The Pagid RSC1 is a good street/track compromise for enthusiasts with Carbon-Ceramic Brakes. Used for sprint racing and track days compound with all known types of ceramic brake discs. An ideal combination of cold friction, fade resistance and low thermal oxidation of the disc surface.
D1-206 Girodisc Front Replacement Rotor Rings (McLaren 720S)
Girodisc D1-206 Girodisc Front Replacement Rotor Rings (McLaren 720S) $950.00
REPLACEMENT ROTOR DISCS ONLY, DOES NOT INCLUDE ALUMINUM HAT. FITS: McLaren 720S Competition Motorsport is an Authorized dealer for GiroDisc products and we are one of the largest stocking dealers in the country.  We ship most products same or next business day to ensure we meet your delivery deadline. The GiroDisc replacement rotor system is a direct rotor disc replacement for the Giro Disc 2-piece hat and rotor and no modifications are necessary.   The rotor and hat mount together through a floating mount system which utilizes 8-10 high strength alloy steel drive pins manufactured by GiroDisc in the USA to our own specifications and are cadmium plated for corrosion resistance.  The alloy drive pins transfer the load from the brake action while maintaining the axial and radial float between the disc rotor and hat.  The pins are secured by grade 12 cap screws with hardened washers and mounted with anti-noise spring washers to allow for heat expansion while eliminating the rattle and noise associated with floating rotors. The 2-piece GiroDisc design allows for rotor only replacement to minimize replacement costs and deliver outstanding performance and cooling. Sold/Priced per pair.
D2-159 Girodisc Rear Replacement Rotor Rings (McLaren 570-650S-720S)
Girodisc D2-159 Girodisc Rear Replacement Rotor Rings (McLaren 570-650S-720S) $800.00
REPLACEMENT ROTOR DISCS ONLY, DOES NOT INCLUDE ALUMINUM HAT. FITS: McLaren 570, 650S, & 720S Competition Motorsport is an Authorized dealer for GiroDisc products and we are one of the largest stocking dealers in the country.  We ship most products same or next business day to ensure we meet your delivery deadline. The GiroDisc replacement rotor system is a direct rotor disc replacement for the Giro Disc 2-piece hat and rotor and no modifications are necessary.   The rotor and hat mount together through a floating mount system which utilizes 8-10 high strength alloy steel drive pins manufactured by GiroDisc in the USA to our own specifications and are cadmium plated for corrosion resistance.  The alloy drive pins transfer the load from the brake action while maintaining the axial and radial float between the disc rotor and hat.  The pins are secured by grade 12 cap screws with hardened washers and mounted with anti-noise spring washers to allow for heat expansion while eliminating the rattle and noise associated with floating rotors. The 2-piece GiroDisc design allows for rotor only replacement to minimize replacement costs and deliver outstanding performance and cooling. Sold/Priced per pair.