Data System Components

AiM Sports LCU-One Lambda Controller P/N X08LCU1SAC090 The new AiM LCU-One Lambda Controller (SKU: X08LCU1SAC090) is the direct replacement for the now-retired X08LCU05CAN unit. This latest generation controller delivers high-precision wideband air/fuel ratio readings via CAN protocol and integrates seamlessly into your AiM data system—whether you're running an EVO5, MXG, or Solo 2 DL. If you're tuning for performance, reliability, or just data sanity, this is the sensor to trust. Next-Gen Lambda Monitoring for AiM Systems Features: Direct Replacement: Replaces SKU X08LCU05CAN with identical performance and plug-and-play compatibility. CAN Protocol Data: Streams precise air/fuel ratio to your AiM logger or dash via CAN for real-time engine tuning feedback. Wide Compatibility: Works with a wide range of AiM systems (listed below) with no extra adapters or changes required. Race-Proven Reliability: Built to endure the vibrations, temperatures, and rigors of motorsports environments. Compatible With: M5s, M6 EVO4S, EVO5 SOLO2DL MXS 1.2 / 1.3 (including Strada) MXP 1.2 / 1.3 (including Strada) MXG 1.2 / 1.3 (including Strada) MXT, MXT Strada MXM M5660S XLog ECU Log AiM LCU-One Lambda Controller FAQs: Is this compatible with my older LCU-One setup? Yes, this is a drop-in replacement for the X08LCU05CAN and functions identically. Do I need to update my firmware? Most modern AiM systems will auto-detect. However, a firmware update may be required for older units. Always check your device’s latest firmware compatibility list. Can this be used with aftermarket ECUs? Yes, as long as the ECU supports AiM CAN integration, this unit can send wideband data seamlessly. Is the sensor included? This listing is for the Lambda controller. Some kits may include the Bosch LSU 4.9 sensor, but always confirm package contents before ordering. Replace your outdated unit with the latest LCU-One Lambda Controller and keep your data dialed in with uncompromising precision.

AiM 22-Pin Dash Harness This 90° dash wiring harness plugs into the 22-pin connector on an AiM MXP, MXL2, MXm, MXG, or MXS dash, or the AiM EVO5 data-logger. Several of the advanced functions rely on this harness, which is not included with the standard kit for these units. AiM 22-Pin Auxiliary Harness Details Manufacturer: AiM Sports Manufacturer part number: V02573020 Alternate part number: MC-249 22-Pin Coupler Angle: 90° The AiM 22-Pin Auxiliary Harness Provides Additional Function Access This harness provides access to the following additional channels/functions: Analog sensor channels 5, 6, 7, 8  Digital wheel speed sensor inputs 2, 3, 4  Digital 12 VDC outputs 1, 2  RS232 ECU connection The factory harness that comes with the AiM MXG, MXS, MXL2 allows only four inputs. If you would like more inputs then this is your harnessFor use with AiM MXm, MXS, MXP, MXL2, and MXG dashes, and EVO5 logger. This cable is not compatible with older AiM MXL Pro, MXL Pro05, or AiM EVO series. AiM 22-Pin Auxiliary Harness Primary Uses The primary use of the AiM 22-Pin Auxiliary Harness is adding analog sensors. Your original harness will allow up to four analog channels (sensors). These could be Water Temperature, Oil Temperature, Oil Pressure and Brake Pressure. Using the AiM 22-Pin Auxiliary Harness, you can add four more analog channels (sensors) such as Steering Angle, Throttle Position, Gear Box Temperature, and Differential Temp. Another way we often see this cable used is Independent Shock Travel (at each corner) or Engine Oil Temperature both pre-cooler and post-cooler.

AiM Sports GPS09 Module The GPS09 module from AiM further expands the track mapping abilities of AiM data loggers and dash loggers. In addition, the GPS09 allows lap timing (even split times) without the use of trackside beacons, storing data for up to 50 tracks with up to 5 splits per track. The GPS09 can also calculate and log speed, lateral and longitudinal g-forces, and of course vehicle position.The GPS09 is the latest version, boasting a quicker 25 Hz sampling rate (up from 10 Hz) and positional accuracy to less than one foot (down from 2 meters). It also takes full advantage of Race Studio 3's integration of GPS, video, and data. Simple to install: Just connect the CAN cable to your dash and mount the magnetic-backed GPS antenna to your vehicle roof. The GPS unit will even automatically configure itself during start-up! The GPS09 connects via a 5-pin 712 screw-in connector and is compatible with current-generation AiM MXL2/ MXG/MXP/MXS auto dashes, EVO4S/EVO5 data loggers, and SmartyCam HD GP 2.2. Choose a cable length to suit your installation: 1.3m (4 ft) is appropriate for most formula cars and bikes. 4m (13 ft) is long enough for sedans. SmartyCam Note: Only the SmartyCam HD GP 2.2 takes this version. SmartyCam HD, SmartyCam HD GP, and SmartyCam HD 2.1 all require the AiM GPS09B which has a 4-pin connector. MXL / EVO3 / MyChron4 Note: This version is only compatible with the latest-generation loggers; it is not backwards-compatible with the first-gen MXL, the EVO3, or the MyChron4. Solo2/Solo2 DL, MXm, and MyChron6 Note: these do not use an external GPS module; all GPS functions are internal. Compatible With The Following: GPS09 (five pin): MXL/MXL2, MXG, MXP, MXS, and MXm dashes, SmartyCam GPHD Rev 2.2, EVO3, EVO4S, and EVO5 GPS09B (four pin): SmartyCam GPHD Rev 2.1, SmartyCam GP Rev 2.1 Available in either Standard or Roof-Mount versions.

AiM ACC3 Analog CAN Converter (replaces AiM Sports MyChron Expansion Channel Multiplier X80MYCEXP00) The AiM ACC3 Analog CAN Converter is your ticket to unlocking virtually endless expansion for your vehicle’s data acquisition system. Compact, rugged, and easy to integrate, the ACC3 adds up to four fully configurable analog channels—or a mix of two analog and two digital—without using or altering any existing system inputs. Whether you’re tracking temps, voltages, or speeds, this device gives you the freedom to connect the sensors you need for deeper insights. Expand Your Data Logging Capabilities Engineered for versatility, the AiM ACC3 works seamlessly with a wide range of sensors, from thermocouples to 0–12V signal devices. Just note that thermocouples require dedicated compensated cables, so AiM offers different kits and harnesses to match your setup. The result? More data, more accuracy, and better performance analysis at the track. Features and Specifications Analog channels: four fully configurable channels, 200 Hz each (Thermocouple, Thermoresistor, 0–5 volts, 0–12 volts)Speed inputs: two (AN3-AN4), max frequency 10 kHz, internal pull-up for open drain/collector inputExternal power: 9–15 VDCConnection: 1 Analog 8-pin Binder 712 + AiM CAN 5-pin Binder 712Material: PA6 30% glassDimensions: 44.0 x 38.0 x 19.8 mmWeight: 50 gWaterproof rating: IP65 FAQs Can the AiM ACC3 be used with MXL2, MXS, or MXG systems? No, it is not compatible with MXL2, MXS, and MXG models. What types of sensors can I connect? It can handle thermocouples, 0–5V, and 0–12V sensors, plus speed sensors on the designated channels. Do I need special cables for thermocouples? Yes, thermocouples require dedicated compensated cables to ensure accurate readings. Is it suitable for use in wet conditions? Yes, with an IP65 waterproof rating, it’s protected against dust and low-pressure water jets. Maximize your data acquisition potential with the AiM ACC3 Analog CAN Converter—designed for racers who demand more insight and precision from their telemetry systems.

AiM Sports TC Thermocouple Multiplier Hub The AiM TC Hub lets you simply your sensor wiring, allowing the various sensors to plug into the hub with a single cable routed back to the logger. Additionally, the TC Hub has four temperature inputs labelled TEMP 1, TEMP 2, TEMP 3 and TEMP 4, giving you a wide range of different operating temps you can monitor. It communicates with AiM data-loggers by using a CAN network and supports K-Type thermocouples only. Available sensors for the TC Hub include EGT (exhaust gas temp), M5 Water/Oil Temperature Sensor and the M10 Water/Oil Temperature Sensor for cars. AiM thermocouples are all cabled with a male Mignon connector. The TC Hub features a metallic Binder, meaning patch leads are required. AiM thermocouple patch leads (712 3-pin) are available in 1.5 meter to 3 meter lengths. Key Features of the AiM TC Thermocouple Multiplier Hub Configurable up to 50Hz per channel Enhances your data- or dash-logger performance Simplifies your wiring 5-pin Binder 712 male connector

AiM ECU Bridge with RS232 / CAN Wiring Connecting to the ECU allows the AiM unit access to data collected by your ECU (RPM, road speed, coolant temperature, and throttle position are typical; many ECUs offer much more information). Works with the following AiM displays with the male 5-pin CAN connector: AiM MXG AiM MXS AiM MSM AiM MXL & MXL Pro G-Dash Display Formula Car Wheel Display SmartyCam requires the AiM 7-pin to 5-pin CAN Cable (Part No. MC-542, included with the SmartyCam). The ECU Bridge also features a special port for a USB cable (included) for easy connection to your computer for setup. ECU Bridge is available with CAN/RS232 connection, for direct installation on aftermarket ECUs. ECU Bridge and RPM Bridge are needed whenever engine data are to be visualized on a display or a SmartyCam video, if no recording is required. ECU Bridge is used when the ECU transmits data via OBDII, CAN or RS232. AiM has developed hundreds of different protocols to make compatibility with virtually any ECU possible, stock or aftermarket. ECU Bridge has to be properly configured with Race Studio 2 software to communicate with the different visors/cameras on one side and ECUs on the other side. Wiring Protocol and Details CAN protocol for external modules (visors or SmartyCam HD) USB port for PC communication External power 8/18 V

AiM 23-Pin MXS/MXP/MXG Strada Harness This add-on harness plugs into the 23 pin AMP connector on the AiM MXS 1.2 Strada, MXP Strada, and MXG 1.2 Strada street dashes to unlock certain dash features. If you don't want to build your own harness, this harness is required in order to use the following features: Analog input channels (8) Digital wheel speed channel (1) RPM input Digital output CAN2 stream input Manufacturer: AiM Manufacturer part number: V02573220 For use with AiM MXS 1.2 Strada (Standard and "Street Icons"), MXP Strada, and MXG 1.2 Strada only. Not for original MXS Strada, MXS/MXP/MXG data logging dashes, or any other dash or logger.

AiM OBD Harness for MX-Series Strada Dashes AiM Sports specialized wiring harness compatible with the AiM MXS 1.2 Strada, MXP Strada, and MXG 1.2 Strada street dashboards. Designed to seamlessly connect via a 14-pin AMP connector, this harness ensures efficient power, ground, USB, and CAN expansions. Additionally, it facilitates a direct ECU link through the OBDII diagnostic port. Ideal for production vehicles equipped with an OBDII port, the harness supports both CAN and K-Line communication standards.

AiM Sports Position Sensors Add the appropriate AiM Sports Position Sensor to your AiM vehicle data acquisition set-up to retrieve exactly the information you need to maximize your performance and take your racing to the next level! All sensors have a 30cm (12 in.) cable length Note: sensors typically take 3 to 5 business days to ship.

AiM Sports Pressure Sensor Add the appropriate AiM Sports Pressure Sensor to your AiM data acquisition set-up to retrieve exactly the information you need to maximize safety and performance, and take your racing to the next level! All sensors have a 40 cm (15.75 in) cable length. Note: sensors typically take 3 to 5 business days to ship.

AiM Sports Data Hub Extend the capabilities of your AiM MXL, MXL2, MXG, MXS dash logger or EVO4 data logger without occupying any more channels or running more cables to your dash. Connect up to four CAN peripherals to each Data Hub. You can even "stack" Data Hubs, connecting up to four more hubs to each hub, multiplying the number of available connections! Accepts any AiM CAN accessory, including GPS, LCU-One Lambda Controller, Memory Key, or TC (Thermocouple) Hubs. Any channel can be selected for display on the dash. This data hub can also be used to link your SmartyCam to any AiM dash.

AiM Patch Cable With Microphone AiM CAN patch cable with integrated external microphone to connect any supported AiM data-logger to a SmartyCam HD Rev 2.1 / SmartyCam GP HD Rev 2.1. Not compatible with SmartyCam GP HD Rev 2.2. AiM CAN Patch Cable Details Manufacturer: AiM Sports Manufacturer part no.: V02566240 Length: 4 meters (13.1 feet) Connectors: 7-pin 712 male to 5-pin 712 male

AiM Patch Cables With 3.5mm Microphone Input The original AiM SmartyCam, the SmartyCam HD Rev 2, and the SmartyCam HD GP Rev 2.1 all have an internal microphone to capture great racing sound, but it does limit your mic placement options. This specially-designed cable has a 3.5mm mono input jack to connect a second external microphone to your SmartyCam. The input from this jack is automatically mixed with the sound from the SmartyCam's internal microphone. SmartyCam Microphone Cable Fitment Original SmartyCam (2009-13, with the viewing screen on top) Exp port to AiM dash/logger or SMC Bridge SmartyCam HD Rev 2 or later (2015+) Exp port to AiM dash/logger or SMC Bridge SmartyCam HD GP Rev 2.1 or earlier (to 2018) Exp port to AiM dash/logger or SMC Bridge AiM SmartyCam CAN Cable with Microphone Jack, 4M Details Manufacturer: AiM Sports Manufacturer part number: V02566300 Alternate part number: MC-552 Dash, Solo DL, Solo2 DL End: 5 Pin Male 712 SmartyCam End: 7 Pin Male 712 Microphone jack: 3.5mm female mono Cable length: 4 meters (13.1 feet) Length from 7 pin 712 to "Y" Adapter: 50mm Length from Y adapter to 5 pin 712" 4 Meter Length from Y adapter to microphone 3.5mm female jack: 900mm The 7-pin 712 connector plugs into the CAN port on the original AiM SmartyCam. A 5-pin connector on the other end connects your SmartyCam to your AiM data logger, SMC Bridge, etc. Measures four meters (13..1 feet) long. 3.5mm mono microphone jack is attached to the lead. This cable is not compatible with the first SmartyCam HD, which has a 5-pin plug.