430 Challenge

Ferrari F430 Challenge Front Rotors Upgrade your Ferrari F430 Challenge with Girodisc 2-piece front rotors—precision-engineered to replace the stock carbon-ceramic system with a lighter, more durable iron design. Built for endurance and performance, these rotors maintain factory brake balance while delivering the superior thermal management and serviceability demanded by track-focused drivers. Each Girodisc rotor features a 6061-T6 aircraft-grade aluminum hat mated to Girodisc’s proprietary cast-iron rotor ring. The curved vane design acts as a centrifugal pump, drawing air through the disc to reduce heat and maintain consistent stopping power lap after lap. All components are designed, cast, and machined in-house in the USA for unrivaled quality and precision. Iron Strength, Race-Proven Cooling Vehicle Fitment Ferrari F430 Challenge Also compatible with carbon-ceramic brake (CCM) conversions on F430 platforms Girodisc A1-102 Features Direct OEM replacement: Fits factory calipers with no modifications required. Pad compatibility: Designed for use with pads having ≤66mm annulus for optimal weight and performance. Curved vane design: Promotes efficient airflow through the rotor for enhanced cooling and fade resistance. Floating 2-piece construction: Allows thermal expansion while maintaining even pad contact. Anti-noise hardware: Spring washers eliminate rattle while preserving float capability. Made in the USA: Fully machined, heat-treated, and assembled by Girodisc. Girodisc A1-102 FAQs Do these rotors fit the OEM Ferrari calipers? Yes, they bolt directly to factory F430 Challenge calipers with no modifications. Do I need special brake pads? You’ll need pads with a 66mm or smaller swept area, a common spec for 6-piston Brembo calipers. Are these rotors lighter than stock? Yes. They maintain a balance between weight reduction and improved heat capacity for optimal lap performance. Do they reduce brake fade? Absolutely. The curved vane system rapidly dissipates heat to prevent fade during repeated high-speed braking. How are they sold? Sold and priced per pair. Bring race-ready precision to your Ferrari F430 Challenge with Girodisc front rotors—crafted to perform under the most demanding conditions while offering serviceable, long-term reliability.

Girodisc Ferrari F430 Challenge Rear Rotors Purpose-built for the Ferrari F430 Challenge, these Girodisc rear rotors deliver uncompromising braking performance, thermal stability, and serviceability for track environments. Designed as a direct replacement for the original rotors, they provide improved cooling and reduced unsprung mass while maintaining OEM fit and balance. Vehicle Fitment Ferrari F430 ChallengeDirect OEM replacement for factory iron rear rotorsCompatible with original Brembo race calipers and hardware. Track-Tested Engineering The Girodisc system bolts directly to factory hubs with no modifications required. Each rotor features a precision-machined 6061-T6 aluminum hat mated to Girodisc’s proprietary cast-iron friction ring—poured, machined, and assembled entirely in the USA. The curved vane internal design acts as a centrifugal pump, pulling air through the rotor to keep temperatures stable under prolonged braking loads. The floating hardware maintains even pad contact, improves modulation, and prevents warping, ensuring reliability through long race sessions. Features • Direct OEM replacement – bolts to factory hardware• 6061-T6 billet aluminum hats with hard-anodized finish• Proprietary high-carbon cast-iron rings for exceptional durability• Floating mount system with cadmium-plated steel drive pins• Anti-noise spring washers eliminate rattle while maintaining float• Curved vane design optimizes airflow and cooling efficiency• Fully rebuildable – replace only the iron rings when worn• Manufactured and assembled in the USA• Sold/priced per pair Girodisc A2-102 Rear Rotor FAQs: Are these rotors a direct fit for the Ferrari F430 Challenge? Yes. They are designed as a precise bolt-on replacement using the stock Brembo racing calipers and factory hardware. Do I need to modify my brake system? No. The Girodisc rotors maintain the OEM dimensions, ensuring perfect compatibility with your existing setup. Can these be used on street-driven F430 models? These are specifically designed for track-only Challenge cars; for road-going F430 models, Girodisc offers a separate rotor fitment. What are the advantages over stock rotors? Girodisc rotors offer better cooling, lighter weight, and a rebuildable design—ideal for endurance and sprint racing applications. Equip your Ferrari F430 Challenge with Girodisc rear rotors—precision-engineered for endurance, balance, and unmatched performance on the circuit.

Girodisc Ferrari F430 Challenge Rear Replacement Rings Maintain the precision braking performance of your Ferrari F430 Challenge with Girodisc rear replacement rings. These high-carbon iron friction rings are direct replacements for your existing Girodisc two-piece rotor assemblies, designed to restore original stopping power and fade resistance for both track and competition use. Vehicle Fitment Compatible with:• Ferrari F430 ChallengeNote: These are replacement friction rings only. They mount directly to existing Girodisc aluminum hats using the included hardware kit. Track-Proven Durability The Girodisc D2-102 rings are precision-machined from a proprietary high-carbon iron alloy, offering improved heat dissipation, stable coefficient of friction, and excellent crack resistance under repeated hard braking. The curved vane design acts as a centrifugal air pump, keeping your brakes cooler and more consistent during extended lapping or endurance events. Manufactured and balanced in the USA, Girodisc replacement rings ensure long-term performance and serviceability for your F430 Challenge. Features • Direct replacement for Girodisc rear rotor assemblies• High-carbon cast iron ensures consistent performance under heat• Curved vane internal design promotes efficient cooling• Includes complete hardware kit for reassembly• Designed for Girodisc aluminum hats only• Machined and finished in the USA• Sold/priced per pair Specifications • Application: Rear axle• Vehicle: Ferrari F430 Challenge• Material: High-carbon cast iron• Includes new hardware• Made in the USA• Sold/priced per pair Girodisc D2-102 Replacement Ring FAQs Are these compatible with the standard Ferrari F430? No. These replacement rings are engineered for the F430 Challenge application and are not compatible with standard F430 street car brake systems. Do these rings include new hardware? Yes, each set includes new drive pins, washers, and fasteners required for proper assembly to your existing Girodisc hats. Do I need to replace the aluminum hats? Not unless they are damaged or worn. The Girodisc two-piece design allows the hats to be reused with new rings, reducing long-term maintenance cost. Can these be used for endurance racing? Absolutely. Girodisc components are designed for demanding track environments and offer proven reliability in high-temperature racing conditions. Restore factory-level braking precision to your Ferrari F430 Challenge with Girodisc D2-102 rear replacement rings — precision-crafted for performance, consistency, and long-term serviceability.

Pagid Racing Brake Pad Shape No. 8091 Fits the Following Vehicles: Make Model Build (Year) Front Rear Chevrolet Camaro Z28 [Gen 5] [ceramic brakes] 2015 - 17 X Chevrolet Corvette C6 Brembo [ceramic brakes] 2009 - 13 X Chevrolet Corvette C6 Brembo [6-piston iron rotors] 2009 - 13 X Chevrolet Corvette C7 Z06 [ceramic brakes] 2015 + X Ferrari 430 Challenge [ceramic brakes] X Ferrari 430 Scuderia [ceramic brakes] 2007 - 10 X Ferrari 458 Italia [ceramic brakes] 2010 - 15 X Ferrari 488 Challenge race car [ceramic brakes] 2016 + X Ferrari 599 GTB Fiorano [iron rotors] 2006 - 12 X Ferrari Several ceramic (CCM) brakes X McLaren 570S [ceramic brakes] 2015 + X McLaren 650S / Spyder [ceramic brakes] 2014 - 17 X McLaren 675LT [ceramic brakes] 2015 + X McLaren MP4-12C [ceramic brakes] 2011 - 14 X Fits the Following Calipers: Make Type Remarks Shape No. Brembo XA5.71.xx 6-piston D85 16mm 8091 Pagid Racing Brake Pads are engineered for high-performance driving, delivering exceptional stopping power, durability, and control under the most demanding conditions. Trusted by professional racers and performance enthusiasts worldwide, these pads are crafted using advanced friction materials and cutting-edge technology to ensure consistent performance, low fade, and excellent modulation. Whether you're on the track or tackling aggressive street driving, Pagid Racing Brake Pads provide the reliability and confidence you need to push your vehicle to its limits. Pagid Racing Brake compounds are for steel (cast iron) rotors only unless otherwise noted. Pagid RSL 1 Compound: Used in GT cars, touring cars and prototype endurance racing. Due to the high friction and good modulation, often used in sprint races as well. RSL 1 is a low metallic resin bonded material containing steel and aramid fibers with very high heat resistance. It maintains a constant friction level over a wide range of temperatures. Its reduced wear rate and disc friendliness make this material appropriate for endurance races. In the 8091 pad shape, the RSL 1 comes in an RSL 1 Special compound, both specified for Brembo and Ford Multimatic applications. Pagid RSL 19 Compound: Pagid RSL 19 is a low metallic resin bonded material containing steel and aramid fibers. It maintains a constant friction level across a broad range of temperatures. The material features very good modulation and release characteristics. Rear axle usage in combination with RSL 1 or RSL 2 on the front axle in heavier cars (GT3/GTE). Front axle usage for lighter GT and touring cars. Pagid RSC 1 Compound (Ceramic Rotors Only): A race and track day compound for all known types of ceramic brake discs, RSC 1 is a low metallic resin bonded material containing steel and aramid fibers. This material features good all-round characteristics and is suitable for all types of usage. Pagid RSC 2 Compound (Ceramic Rotors Only): Pagid RSC 2 is a special race compound for ceramic discs with a high content of fibers in the friction surface for sprint and endurance circuit racing. RSC 2 is a low metallic resin bonded material containing steel and aramid fibers. This material is specifically developed for above mentioned applications. Pagid RSC 3 Compound (Ceramic Rotors Only): RSC 3 is a low metallic resin bonded material containing steel fibers. This material is specifically developed for above mentioned applications. It is a special race compound for ceramic discs with low content of fibers in the friction surface for sprint and endurance circuit racing.

D2-102 Girodisc Rear Replacement Rotor Rings (Discontinued Rotor Design) Discontinued Rotor Design, Final Sale, No Returns or Excahanges FITS: FERRARI 430 CHALLENGE REPLACEMENT ROTOR DISC ONLY, DOES NOT INCLUDE ALUMINUM HAT. Competition Motorsport is an Authorized dealer for GiroDisc products and we are one of the largest stocking dealers in the country.  We ship most products same or next business day to ensure we meet your delivery deadline. The GiroDisc replacement rotor system is a direct rotor disc replacement for the Giro Disc 2-piece hat and rotor and no modifications are necessary.   The rotor and hat mount together through a floating mount system which utilizes 8-10 high strength alloy steel drive pins manufactured by GiroDisc in the USA to our own specifications and are cadmium plated for corrosion resistance.  The alloy drive pins transfer the load from the brake action while maintaining the axial and radial float between the disc rotor and hat.  The pins are secured by grade12 cap screws with hardened washers and mounted with anti-noise spring washers to allow for heat expansion while eliminating the rattle and noise associated with floating rotors. The 2-piece GiroDisc design allows for rotor only replacement to minimize replacement costs and deliver outstanding performance and cooling. Sold/Priced per pair.

Pagid Racing Brake Pad Shape No. 4906 Fits the Following Vehicles: Make Model Build (Year) Front Rear Chevrolet Camaro Z28 [Gen 5] [ceramic brakes] 15 - 17 X Chevrolet Corvette C6 Brembo [ceramic brakes] 09 - 13 X Chevrolet Corvette C7 Z06 [ceramic brakes] 15 - X Dodge Viper ACR [ceramic brakes] 14 - 17 X Ferrari 360 Challenge Stradale [ceramic brakes] 03 - 05 X Ferrari 430 Challenge [ceramic brakes] X Ferrari 430 Scuderia [ceramic brakes] 07 - 10 X Ferrari 458 Italia [ceramic brakes] 10 - 15 X Ferrari 488 Challenge race car [ceramic brakes] 16 - X Ferrari 599 GTB Fiorano 06 - 12 X Ferrari Enzo [ceramic brakes] 02 - 04 X Ferrari F430 [ceramic brakes] 05 - 10 X Ferrari Several ceramic brakes CCM X Lamborghini Aventador LP700-4 [ceramic brakes] 11 - X Lamborghini Several ceramic brakes X Pagid Racing Brake Pads are engineered for high-performance driving, delivering exceptional stopping power, durability, and control under the most demanding conditions. Trusted by professional racers and performance enthusiasts worldwide, these pads are crafted using advanced friction materials and cutting-edge technology to ensure consistent performance, low fade, and excellent modulation. Whether you're on the track or tackling aggressive street driving, Pagid Racing Brake Pads provide the reliability and confidence you need to push your vehicle to its limits. These Pagid Racing Brake compounds are for ceramic rotors only. Pagid RSC 1 Compound (Ceramic Rotors Only) A race and track day compound for all known types of ceramic brake discs, RSC 1 is a low metallic resin bonded material containing steel and aramid fibers. This material features good all-round characteristics and is suitable for all types of usage. Pagid RSC 2 Compound (Ceramic Rotors Only) Pagid RSC 2 is a special race compound for ceramic discs with a high content of fibers in the friction surface for sprint and endurance circuit racing. RSC 2 is a low metallic resin bonded material containing steel and aramid fibers. This material is specifically developed for above mentioned applications.

Girodisc Brake Pad Spreader The Right Tool for the Job This indispensable tool is used by race teams, shops, and enthusiasts alike who have high performance four- and six-piston calipers. The Girodisc Brake Pad Spreader is designed to easily spread brake pads and pistons to facilitate quick replacement of pads and/or rotors in a shop or racing environment. No more screwdrivers, pliers, hammers, or C-clamps! This tool will retract the pistons fully and evenly into their bores with one squeeze of the levers. The Girodisc Brake Pad Spreader was designed to be used with popular racing brake calipers from Brembo, AP Racing, Alcon, and other performance calipers in racing and road use. To help it fit into any caliper, the amount of throw is adjustable. Built Like a Tank. Works Like a Charm. Insert the spreading plates one way for wider six-piston calipers, or turn the spreader 90o and use the plate sides for four-piston calipers. The Girodisc Brake Pad Spreader is made from heavy-gauge steel, powder-coated for durability. The slider is cadmium-plated, and nylon pivot bushings ensure smooth action. It will quickly become an invaluable tool for any race team, shop, or enthusiast who changes pads and rotors frequently.

CMS Performance RF1 DOT4 Racing Brake Fluid Real Life 622º Boiling Point Without the Real High Price RF1 Racing Brake Fluid from CMS Performance is a fully-synthetic DOT4 brake fluid formulated to provide extraordinary performance under the most demanding high-temperature racing and track-day conditions. With a dry boiling point of 622º F / 328º C, RF1 exceeds all DOT 3 & DOT 4 requirements and is compatible with all DOT 3, DOT 4, and DOT 5.1 fluids. Note: RF1, like all DOT 4 brake fluids, is not compatible with DOT 5 silicone-based or any mineral-based brake fluids. On the race track, there is perhaps no single safety system more important than your brakes. No single part of that system is more critical than brake fluid, given the extraordinarily high temperatures it operates under. At CMS Performance, we got tired of (and a little nervous) using "racing" brake fluid at the race track that didn't live up to its claimed performance when things got hot. We found more than a few brands whose product was all hype and not high performance. No Hype. All Performance. No Kidding. So we did something about it. CMS Performance RF1 is manufactured in partnership with Orthene, maker of the also-excellent Halo P1 racing brake fluid and a brake fluid supplier to many racing teams in Formula 1, WEC, and other professional series. RF1 was formulated to maintain consistent viscosity, lubricity, and compressibility at the extreme system temperatures and line pressures found in racing and track days. The bottom line is this: you can spend a lot more on brake fluid, but it's hard to find higher-performance than RF1 Racing Brake Fluid. CMS Performance RF1 Racing Brake Fluid Details: Manufacturer: CMS Performance Manufacturer part no.: CMSRF1 Typical dry boiling point: 622º F / 328º C Typical wet boiling point: 399º F / 204º C Exceeds DOT 3 & DOT 4 standards Bottle size: 500 ml (16.9 fl. oz.) Click Here for Product MSDS Sheet A Word About Flushing Brake Fluid All brake fluid degrades over time (not mileage), attracting water as it ages, which, at high brake temperatures, can lead to fluid boil and brake fade or failure. That's why the "wet" (aged) boiling point of any brake fluid is substantially lower than the "dry" (new) boiling point. To maintain maximum braking performance, Competition Motorsport strongly suggests replacing your brake fluid before every track event, but at least every three months if you're consistently racing and/or driving at track days. It's cheap insurance against learning about brake fade the hard way!