sale
CMS RF1 DOT4 Racing Brake Fluid (500 ml)
00
DAYS
00
HRS
00
MIN
00
SEC
Competition Motorsport CMS RF1 DOT4 Racing Brake Fluid (500 ml) from $21.95 $131.70
Buy 6+, Save $1 per bottle Buy 12+, Save $2 per bottle REDESIGNED BOTTLE, SAME TOP-OF-THE-LINE BRAKE FLUID Competition Motorsport RF1 fully synthetic Racing Brake Fluid is formulated to provide the highest, most reliable performance under racing and track-day conditions, where braking systems operate at very high sustained temperatures. RF1 exceeds all DOT 3 & 4 requirements and is compatible with all DOT 3, 4, and 5.1 fluids. (Not compatible with DOT5 or mineral-based brake fluids.) There is perhaps no single safety system more important in racing than brakes. And no single part of that system is more critical than brake fluid. At Competition Motorsport, we got tired of (and a little nervous) using "racing" brake fluid on the track that didn't live up to its claimed performance when things got heated. So we did something about it. Manufactured in partnership with the brake fluid supplier to many teams in Formula 1, WEC, and many other professional series, RF1 Racing Brake Fluid is formulated to maintain consistent viscosity, lubricity, and compressibility at extreme temperatures and line pressures found in racing, track days, and spirited driving. Bottom line: you can spend more money, but you can't buy higher-performing racing brake fluid!   SPECIFICATIONS: Typical dry boiling point: 622° F (328° C) Typical wet boiling point: 399° F (204° C) Exceeds DOT3 & DOT4 standards Individual 500 ml (16.7 oz.) bottles   Click Here for Product MSDS Sheet All brake fluid degrades over time (not mileage), attracting water as it ages, which, at high brake temperatures, can lead to fluid boil and brake fade or failure. That's why the "wet" (aged) boiling point of any brake fluid is substantially lower than the "dry" (new) boiling point. To maintain maximum braking performance, Competition Motorsport strongly suggests replacing your brake fluid before every track event, but at least every three months if you're consistently racing and/or driving at track days. It's cheap insurance against learning about brake fade the hard way!
Girodisc Pad Spreader GDPS01
Girodisc Girodisc Pad Spreader GDPS01 $250.00
Girodisc Brake Pad Spreader This indispensable tool is used by race teams, shops, and enthusiasts alike who have high performance four- and six-piston calipers. The spreader is designed to spread brake pads and pistons in four- and six-piston calipers to facilitate quick replacement of pads and/or rotors in a shop or racing environment.No more screwdrivers, pliers, hammers, or C-clamps! This tool will retract the pistons evenly and all the way back into their bores with one squeeze of the levers. The Girodisc spreader was designed around popular four-piston and six-piston calipers from Brembo, AP Racing, Alcon, and other performance calipers in racing and road use. To help fit in any caliper, the amount of throw is adjustable.Insert the spreading plates one way for wider six-piston calipers, then turn the spreader 90o and use the plate sides for four-piston calipers.The Girodisc Pad Spreader is made from heavy-gauge steel and is powder-coated for durability. The slider is cadmium-plated, and nylon pivot bushings ensure smooth action. The Girodisc Pad Spreader will quickly become an invaluable tool for any race team, shop, or enthusiast who changes pads and rotors with any frequency.
Race Technologies RE10 Brake Pad - 2450.18.RE10
Race Technologies Race Technologies RE10 Brake Pad - 2450.18.RE10 $649.00
RT RE10*:RE10 is the ultimate endurance race compound offering a balance of excellent stopping power, low thermal conductivity, extremely low pad and disc wear. Utilizing the latest friction material technology, RE10 offers consistent performance under the most demanding of environments. Typical Applications: Professional Endurance Racing, Club Racing, and HPDE on high demand brake platforms *Denotes a "race only" pad. Running a "racing use only" pad on the street could produce excessive noise and dust. Disc wear could be accelerated if driven at cold temperatures or used in the incorrect temperature range. Racing pads are designed to work in specific temperature ranges so it is important to choose the desired compound for the correct environment the vehicle will be used in. Pad Compounds are run on a brake dynamometer over multiple brake applications (stops) to test the materials in a controlled environment for the most accurate data. Wear rates and temperatures can be influenced by car setup, grip levels, track layout/configuration and many other variables.
Race Technologies RE10 Brake Pad - 2451.18.RE10
Race Technologies Race Technologies RE10 Brake Pad - 2451.18.RE10 $549.00
RT RE10*:RE10 is the ultimate endurance race compound offering a balance of excellent stopping power, low thermal conductivity, extremely low pad and disc wear. Utilizing the latest friction material technology, RE10 offers consistent performance under the most demanding of environments. Typical Applications: Professional Endurance Racing, Club Racing, and HPDE on high demand brake platforms *Denotes a "race only" pad. Running a "racing use only" pad on the street could produce excessive noise and dust. Disc wear could be accelerated if driven at cold temperatures or used in the incorrect temperature range. Racing pads are designed to work in specific temperature ranges so it is important to choose the desired compound for the correct environment the vehicle will be used in. Pad Compounds are run on a brake dynamometer over multiple brake applications (stops) to test the materials in a controlled environment for the most accurate data. Wear rates and temperatures can be influenced by car setup, grip levels, track layout/configuration and many other variables.
Pagid Racing Brake Pads No. 4925
Pagid Pagid Racing Brake Pads No. 4925 from $442.83
Fits These Vehicles: Make Model Build (Year) Front Rear Porsche 918 Spyder 2013 +   X Porsche 991 GT3 [ceramic brakes] 2013 +   X Porsche 991 GT3 [iron brakes] 2013 +   X Porsche 991 GT3 RS [ceramic brakes] 2015 +   X Porsche 991 GT3 RS [iron brakes] 2015 +   X Porsche 991 Turbo [ceramic brakes] 2013 +   X Porsche 991 Turbo [iron brakes] 2013 +   X Porsche Cayman GT4 2016 +   X Porsche Cayman GT4 [ceramic brakes] 2016 +   X RSL 29: The PAGID RS29 (Yellow) is the world-leading endurance brake pad used by most of the winning teams in motorsport. Although designed primarily for endurance racing, many competitors use this material successfully for sprint and short distance races also. RS29 has also found favor in the growing track day market due to the level of control, good cold performance, long life and low disc wear. RSC 1: The Pagid RSC1 is a good street/track compromise for enthusiasts with Carbon-Ceramic Brakes. Used for sprint racing and track days compound with all known types of ceramic brake discs. An ideal combination of cold friction, fade resistance and low thermal oxidation of the disc surface RST 1: PAGID RST1 is a high average friction, aggressive pad with instant pedal response, quick release, a firm pedal at all temperatures, and a progressive torque curve. Suitable for applications with high down-force and/or very high grip. 
Pagid Racing Brake Pads No. 4924
Pagid Pagid Racing Brake Pads No. 4924 from $540.04
 Fits These Vehicles: Make Model Build (Year) Front Rear Porsche 991 GT3 [iron brakes] 2013 + X   Porsche 991 GT3 RS [iron brakes] 2015 + X   Porsche 991 Turbo [iron brakes] 2013 + X   Porsche Cayman GT4 2016 + X     RSL 29: The PAGID RS29 (Yellow) is the world-leading endurance brake pad used by most of the winning teams in motorsport. Although designed primarily for endurance racing, many competitors use this material successfully for sprint and short distance races also. RS29 has also found favor in the growing track day market due to the level of control, good cold performance, long life and low disc wear. RSL1: PAGID RSL1 has a high ceramic content with superior thermal insulation and higher heat resistance than metallic pad compounds. They feature excellent pad wear under endurance conditions, excellent rotor life, and are less aggressive than RST pads with excellent brake balance and modulation RST 1: PAGID RST1 is a high average friction, aggressive pad with instant pedal response, quick release, a firm pedal at all temperatures, and a progressive torque curve. Suitable for applications with high down-force and/or very high grip. 
A1-066 Girodisc 2pc Front Brake Rotors (OEM Steel)
Girodisc A1-066 Girodisc 2pc Front Brake Rotors (OEM Steel) $1,700.00
This Girodisc system is a 380mm two-piece steel rotor and aluminum hat combination, a direct-replacement upgrade for the one-piece OEM GT4 steel brakes. The A1-166 will bolt directly to the GT4 and work perfectly with your OEM calipers. There are two main reasons for replacing your OEM rotors: first, the Girodisc rotors are designed to shed heat more effectively than the original rotors; second, the slotted Girodisc A1166 will far outlast the OEM drilled rotors. When subjected to intense heat in a racing or track-day environment, the drilled holes in the OEM rotors originate cracks which can lead to rotor failure. When paired with the Girodisc A2-155 rear rotors, your factory brake bias and ABS efficiency are maintained. When used with Pagid or PFC performance brake pads, and Competition Motorsport RF1 brake fluid (also available from CompetitionMotorsport.com), you have an amazing solution to overheating, cracking and warping rotors. The central hat section of the disc is made from 6061-T6 aircraft specification aluminum.  The disc is manufactured from cast iron which is constructed in the USA and is made to the same specification with the same material used by professional racing organizations.  The rotors curved vane design was developed in racing and acts as a centrifugal pump to force cooling air through the disc.   The rotor and hat mount together through a floating mount system which utilizes eight to ten high strength alloy steel drive pins manufactured by Girodisc in the USA to our own specifications and are cadmium plated for corrosion resistance.  The alloy drive pins transfer the load from the brake action while maintaining the axial and radial float between the disc rotor and hat.  The pins are secured by Grade 12 cap screws with hardened washers and mounted with anti-noise spring washers to allow for heat expansion while eliminating the rattle and noise associated with floating rotors. The two-piece Girodisc design allows for rotor only replacement as well to minimize future replacement costs and deliver outstanding performance and cooling. Sold/priced per pair.
Pagid Racing Brake Pads No. 4927
Pagid Pagid Racing Brake Pads No. 4927 from $616.82
Fits These Vehicles Make Model Build (Year) Front Rear Porsche 918 Spyder 2013 + X   Porsche 991 GT3 [ceramic brakes] 2013 + X   Porsche 991 GT3 RS [ceramic brakes] 2015 + X   Porsche 991 Turbo [ceramic brakes] 2013 + X   Porsche Cayman GT4 [ceramic brakes] 2016 + X   RSL 29: The PAGID RS29 (Yellow) is the world-leading endurance brake pad used by most of the winning teams in motorsport. Although designed primarily for endurance racing, many competitors use this material successfully for sprint and short distance races also. RS29 has also found favor in the growing track day market due to the level of control, good cold performance, long life and low disc wear. RSC 1: The Pagid RSC1 is a good street/track compromise for enthusiasts with Carbon-Ceramic Brakes. Used for sprint racing and track days compound with all known types of ceramic brake discs. An ideal combination of cold friction, fade resistance and low thermal oxidation of the disc surface.
PFC Brake Pads 1773.11.17.44 FRONT
Performance Friction PFC Brake Pads 1773.11.17.44 FRONT $459.95
PFC 11 COMPOUND This is an updated PFC part number. Previous part number was 7721.11.17.44. A new generation sprint and medium-distance friction compound, giving you the ultimate in control with superior disc conditioning. Developed from the PFC 01 compound with improved bite, modulation, and release characteristics. The PFC 11 is ultra-smooth, developed to reduce wheel locking at the end of braking while giving more cold and hot bite than the endurance-oriented PFC 08 compound. FITMENT (Iron Rotors Only): Porsche 991.1 & 991.2 Carrera GT3/GT3RS Porsche 991.2 GT2RS Porsche 981 Cayman GT4 Porsche 991 Carrera 911R
PFC Brake Pads 7727.11.18.44 REAR
Performance Friction PFC Brake Pads 7727.11.18.44 REAR $459.95
PFC 11 COMPOUND A new generation sprint and medium-distance friction compound, giving you the ultimate in control with superior disc conditioning. Developed from PFC 01 compound with improved bite, modulation, and release characteristics. It is ultra smooth, developed to reduce wheel locking at the end of braking while giving more cold and hot bite than the endurance oriented PFC 08 compound. FITMENT (Iron Rotors Only) Porsche 991.1 & 991.2 Carrera GT3/GT3RS Porsche 991.2 GT2RS Porsche 981 Cayman GT4 Porsche 991 Carrera 911R
A2-156 Girodisc 2pc REAR Brake Rotors (OEM PCCB)
Girodisc A2-156 Girodisc 2pc REAR Brake Rotors (OEM PCCB) $1,900.00
PORSCHE 991 TURBO & 981 CAYMAN GT4 OEM PCCB This Girodisc system is a 390mm two-piece steel rotor and aluminum hat combination, a direct-replacement upgrade for the OEM PCCB brakes. The A2-156 will bolt directly to your Porsche and work perfectly with your OEM calipers. There are two main reasons for replacing your PCCB: first, the Girodisc rotors are designed to shed heat more effectively than the original rotors; second, the machined cast iron rotor rings are far more durable than the fragile OEM carbon-ceramic rotors. This is critical when you're swapping wheels on and off the car for track days or racing, because it's so easy to nick a carbon rotor and take a nice chunk out of it. When paired with the Girodisc A1-156 front rotors, your factory brake bias and ABS efficiency are maintained.  When used with Pagid or PFC performance brake pads, and Competition Motorsport RF1 brake fluid (also available from CompetitionMotorsport.com), you have an amazing solution to overheating, cracking and warping rotors. The central hat section of the disc is made from 6061-T6 aircraft specification aluminum.  The disc is manufactured from cast iron which is constructed in the USA and is made to the same specification with the same material used by professional racing organizations.  The rotors curved vane design was developed in racing and acts as a centrifugal pump to force cooling air through the disc.   The rotor and hat mount together through a floating mount system which utilizes eight to ten high strength alloy steel drive pins manufactured by Girodisc in the USA to our own specifications and are cadmium plated for corrosion resistance.  The alloy drive pins transfer the load from the brake action while maintaining the axial and radial float between the disc rotor and hat.  The pins are secured by Grade 12 cap screws with hardened washers and mounted with anti-noise spring washers to allow for heat expansion while eliminating the rattle and noise associated with floating rotors. The two-piece Girodisc design allows for rotor only replacement as well to minimize future replacement costs and deliver outstanding performance and cooling. Sold/priced per pair.
A1-156 Girodisc 2pc Front Brake Rotors (OEM PCCB)
Girodisc A1-156 Girodisc 2pc Front Brake Rotors (OEM PCCB) $1,900.00
991 PORSCHE TURBO & 981 GT4 (OEM PCCB) This Girodisc system is a 410mm two-piece steel rotor and aluminum hat combination, a direct-replacement upgrade for the OEM PCCB brakes. The A1-156 will bolt directly to your Porsche and work perfectly with your OEM calipers. There are two main reasons for replacing your PCCB: first, the Girodisc rotors are designed to shed heat more effectively than the original rotors; second, the machined cast iron rotor rings are far more durable than the fragile OEM carbon-ceramic rotors. This is critical when you're swapping wheels on and off the car for track days or racing, because it's so easy to nick a carbon rotor and take a chunk out of it. When paired with the Girodisc A2-156 rear rotors, your factory brake bias and ABS efficiency are maintained.  When used with Pagid or PFC performance brake pads, and Competition Motorsport RF1 brake fluid, you have an amazing solution to overheating, cracking and warping rotors. The central hat section is made from 6061-T6 aircraft aluminum. The rotor is manufactured in the US from cast iron using the same specs and materials as professional racing organizations. The racing-developed vane design acts as a centrifugal pump to force cooling air through the disc.   Rotor and hat mount together through a floating mount system using high-strength alloy steel drive pins and Grade 12 cap screws. These transfer braking load while maintaining axial and radial float between the rotor and hat for superior heat management. The pins are secured by Grade 12 cap screws with hardened washers and mounted with anti-noise spring washers to allow for heat expansion while eliminating rattle and noise. The two-piece Girodisc design allows for rotor only replacement as well to minimize future replacement costs and deliver outstanding performance and cooling. Sold/Priced per pair.