Racing Seats

Sparco ADV XT Carbon Racing Seat The Sparco ADV XT is an extremely strong, ultra-light weight carbon fiber seat designed to pass the FIA’s highest seat rating, FIA 8862-2009. This means the ADV XT has been tested to an impact of approximately 70G. This rating is required for GT racing, and the ADV XT was specially designed with a more relaxed, comfortable driving position for GT cockpits. With strength at the top of its class, the ADV XT can withstand over 6,600 lbs. of lateral force. The ADV XT has an energy absorbing system in the areas subjected to the highest stress to protect the driver. The entire seat is covered in self-extinguishing fabric, plus a special non-slip fabric in the shoulders and seat area. The ADV XT is FIA approved when mounted with the Sparco #0049605 side-mount brackets. TECHNOLOGY: Ultra-light weight Carbon Fiber construction FIA 8862-2009 approved Testing to an impact of 70G Designed for GT cockpits and driver position HANS device compatible Fire retardant fabric Special non-slip fabric DIMENSIONS:

Sparco Racing Seats ADV Elite Carbon The Sparco ADV Elite is an extremely strong, ultra-light weight carbon fiber seat designed to pass the FIA’s highest seat rating FIA 8862-2009. This means that the ADV Elite has been tested to an impact of approximately 70G. This rating is required for WRC racing, and the ADV Elite was specially designed with an upright driving position preferred by Rally drivers. In addition to the Rally driving position, the outer dimensions have been reduced to fit into typically smaller WRC cockpits. With strength at the top of its class, the ADV Elite can withstand over 6,600 lbs. of lateral force. The ADV Elite has an energy absorbing system in the areas subjected to the highest stress to protect the driver. The entire seat is covered in self-extinguishing fabric and special non-slip fabric in the shoulders and seat area. The ADV Elite is FIA approved when mounted with the Sparco #004988ADV side-mount brackets. TECHNOLOGY Ultra-light weight Carbon Fiber construction FIA 8862-2009 approved Testing to an impact of 70G Designed for WRC Rally cockpits & driver position Hans device compatible Fire retardant fabric Special non-slip fabric DIMENSIONS

Racetech RT9119 Lightweight Racing Seat Building upon the successful 129 series, the Racetech RT9119 racing seat offers the same ergonomic form and incredible features in a lighter and more protective package. Used by many professional teams at both the national and international levels, this is the lightweight version using a precise combination of carbon and Kevlar hybrid weave to achieve a shell weights as low as 9.9 lbs. (4.5kg). Four sizes are available: Standard, Wide, Tall, and Wide & Tall. You can further customize your seat with low-profile base cushions, or by adding side cushions for support in the thigh area. Racetech 119-Series seats (except the WHR) are compliant with FIA 8855-1999 standards1. BRACKETS AND MOUNTING OPTIONS: Side mount to the floor using the Racetech RTB1009M 5mm aluminum brackets (available in the drop-down above). Back mount using the RTB2115B bracket in conjunction with the RTB2005C clamps. The RTB2115B is a 5mm aluminum bracket that bolts directly to the shoulder beam of the seat. The RTB2005C clamps bolt to the RTB2115B and come in three variants: 11/2 inch (38mm), 15/8 inch (41mm), or 13/4 inch (45mm) ID to suit your roll cage tubing diameter. Note 1: In order to comply with FIA 8855-1999, Racetech 119-Series seats must be back-mounted to the roll cage at shoulder level. Back-mounting improves seat strength and stability during an impact, increases driver feel, and reduces driver fatigue. FEATURES: Gel-coat cear self-finish. Seat cover in black fire-retardant fabric. Wear patches black perforated leather. FIA homologation FIA 8855-1999 approved (except RT9119WHR). Shell constructed of Kevlar/carbon. Shell weight from 9.9l bs. (4.5 kg). Integrated air ducting is vented to the driver's lower back. Back-mount compatible. SIZES: Standard (HRW) Wide (WHR) Tall (THR) Wide & Tall (WTHR)     

Sparco SPX Reclining Seat (non-FIA) The SPX is handcrafted in Italy using the same technology and materials used for OEM super cars.  In fact, the SPX is the first carbon fiber reclining seat available to the public that meets the same specifications required by the OEM manufacturers. What this means is that the attention to detail and quality put into the SPX cannot be matched by any other seat manufacturer on the market today.  The Sparco SPX seat represents the ultimate evolution of the sport seat. The SPX uses a combination of carbon fiber and advanced composites that give the driver both comfort and performance in a lightweight package. With the ergonomic shape of the carbon fiber backrest and the seating position of the RTM composite lower, the SPX holds the driver during extreme lateral forces and is comfortable for long road trips.  The SPX is covered in a combination of beautiful perforated and smooth Italian leather. The center of the SPX is covered in Alcantara suede to allow you to gain absolute control of your vehicle and enhance your driving experience. To finish off the performance look, all hand stitching is done in tone-on-tone black with the Sparco logo embroidered in matching black. The gloss finished carbon fiber backrest features a leather pull strap which releases the backrest to fold forward to allow access to a backseat or storage area. The backrest also features a micro adjustment knob that allows you to dial in the perfect driving position.  The SPX is sold in driver and passenger versions (left and right). TECHNOLOGY Lightest carbon fiber reclining seat on the market Gloss carbon fiber back rest RTM composite lower (an advanced composite with strength and weight similar to carbon fiber) Covered in hand-stitched Italian leather and Alcantara suede Leather pull for seat back release Sold in driver (left) and passenger (right) versions SPX DIMENSIONS A LITTLE HISTORY Sparco has designed and engineered some of the most advanced sport seats in the world, including the first-ever adjustable carbon fiber seat in 1998 for the Lamborghini Diablo. Since then, countless super cars such as the Bugatti Veyron and Lamborghini Aventador have used Sparco design and technology in their vehicles. In addition to seats, Sparco also produces carbon fiber body panels, bumpers, roofs and aerodynamic pieces, in addition to structural carbon fiber parts like stressed-member engine cradles and other chassis parts.  Supplying OEM manufacturers requires every part to pass demanding safety and durability tests. Sparco’s extensive expertise in carbon fiber technology is why they're a Tier One supplier for Alfa Romeo, AMG, Aston Martin, Audi, Bentley, Bugatti, Ferrari, Koenigsegg, Lamborghini and Lotus to name a few. 

Sabelt X-Pad Carbon Racing Seat The Sabelt X-Pad Carbon is exceptionally light weight, the perfect seat for those racing smaller cars with limited interior space who still demand the safety of a full-containment seat. Sabelt has managed to by making the shell smaller and lighter while maintaining interior seat dimensions that fit most average racing drivers. The X-Pad Carbon is Sabelt’s most compact seat yet, specifically designed to fit in smaller cockpits and offering the safety and weight savings of a high-strength carbon fiber shell. They achieved this by replacing bulky racing seat padding with significantly thinner, but still very comfortable foam padding. You'll never miss the added bulk! The exterior dimensions of the seat were reduced by changing key elements -- like eliminating the "rolled" upper edges of the seat -- which combine to reduce the width significantly without narrowing the seat to the point where it would only fit small drivers. The Sabelt X-Pad Carbon is a premium example of how game-changing innovation can be discovered in plain-sight; it doesn't always require a shake-up to standard conventions. FEATURES: FIA 8855-1999 homologation. Weight: 13.7 lbs (6.2 kg). Super-light carbon fiber shell construction. Standard side mounting. Perfect full-containment seat for small cockpit cars. Shoulders and hips designed for Regulation 8862 to improve driver safety.

Sabelt GT-AM Racing Seat Based on the same shell shape as the top of the range GT Pro seat the Sabelt GT AM  is a professional competition seat manufactured from lightweight fibreglass making it a more affordable option to clubman competitors. FIA 8855-2021 approved Lightweight fibreglass shell construction Integral wrap around head protection reduces the risk of neck injuries Deep side bolsters provide superb levels of lateral support and impact protection Seat pads are available in different thicknesses to allow for a more tailored fit (see pull-down menu) The Sabelt GT AM seat has been designed to offer superb levels of safety with comfort. Deep side bolsters not only offer excellent lateral support but they also keep the occupants legs inside the seat structure for impact protection. The integral wrap around head support helps prevent neck injuries by preventing excessive lateral head movement in the event of a crash. Deep wrap around shoulders provide support to the upper body, reducing unwanted lateral movement. The seat is covered with removable pads constructed from high density foam which absorb vibration and shock loads to improve comfort and reduce fatigue. Replacement cushions in different thicknesses are available to allow for a more tailored fit. The seat is compatible with all types of FHR device including hybrid types. 6 Harness slots allow the seat to be used with any type of Motorsport harness. For FIA Homologation purposes the GT AM seat must be used with specific side mounts, available in the pull-down menu.

Sabelt Titan Carbon Racing Seat The Sabelt Titan Racing Seat has been known for being simple and elegant. With the new Titan Carbon Racing Seat, Sabelt maintains that tradition while introducing an ultra-lightweight, autoclave carbon fiber shell and a more rounded design aimed at reducing weight by over 25%. The Sabelt Titan Carbon was developed in partnership with the best companies racing in GT Championships around the world. The Titan Carbon is both very light weight, extremely safe, and incredibly comfortable. Offered in two sizes (Standard and Max) to accommodate a wide range of drivers, the Titan Carbon is beautifully upholstered including 3D mesh panels that offer excellent breathability to help reduce driver fatigue. The result is an amazingly light, safe, comfortable racing seat. CMS Exclusive: for a limited time, add Sabelt lightweight aluminum side mounts and hardware kit (in the dropdowns above) at no additional cost. FEATURES: FIA 8855-1999 homologation Weight: Standard 15.6 lbs (7.1 kg); Max 15.2 lbs (6.9 kg) Deep side bolstering to prevent lateral movement Six-point harness ready (sub-belt hole in the bottom of the shell) High-wear velour fabric upholsters the main shell Breathable mesh 3D fabric on backrest and bottom Kinderpoint anti-slip fabric on shoulder bolsters

Racetech RT4119HRW Racing Seat Building upon the successful 129-Series, the Racetech RT4119 offers the same ergonomic form and incredible features in a lighter and more affordable package. The RT4119 is used by many professional teams at both the national and international levels. There are four sizes available: Standard, Wide, Tall, and Wide & Tall. Customize your seat further by adding low-profile base cushions, or you can add side cushions for support in the thigh area. The 119-Series seats are compliant with FIA 8855-1999 standards1. BRACKET AND MOUNTING OPTIONS: Side mount to the floor using Racetech RTB1009M 5mm aluminium brackets. Back mount using the RTB2115B bracket in conjunction with RTB2005C clamps. The RTB2115B is a 5mm aluminium bracket that bolts directly to the shoulder beam of the seat. The RTB2005C clamps bolt to the RTB2115B and come in three variants: 11/2 inch (38mm), 15/8 inch (41mm), or 13/4 inch (45mm) ID to suit the roll cage tubing diameter in your vehicle. Note 1: In order to comply with FIA 8855-1999, Racetech 119-Series seats (except the RT4119HRW) must be back-mounted to the roll cage at shoulder level. Back-mounting improves seat strength and stability during an impact, increases driver feel, and reduces driver fatigue. FEATURES: FIA homologation complies with FIA 8855-1999 regulations. Shell construction of composite (GRP) Shell weight from 16.8 lbs. (7.6 kg). Large harness guides. Air ducting vented to the driver's lower back. Back-mount compatible. SIZING: Standard (HRW) Wide (WHR) Tall (THR) Wide & Tall (WTHR)

OMP WRC-R Carbon Racing Seat The OMP WRC-R Carbon Racing Seat offers professional-level features in a an ultra-light, carbon fiber design with aggressive side and thigh bolsters. Upholstered in OMP's highly breathable Airtex material to keep you cool and improve performance even in the hottest conditions. The WRC-R Carbon features removable back/base cushions and a comfortable split-leg bottom cushion. High side-bolsters offer excellent lateral leg support, while the HANS-compatible shoulder harness slots accomodate various driver heights. Seat gel-coated fiberglass shell. Large . High side bolsters for lateral leg support for higher protection. Removable back, base and leg cushion for maximum individual seating comfort. FEATURES: FIA homologated to 8855-1999 standard Made from ultra lightweight carbon fiber Removable cushions in the back, base and split leg High side bolsters for great lateral leg support Large harness slots 12.3 lbs (5.6 kg)

Sparco QRT-C Performance Carbon Racing Seat The QRT-C Performance Carbon seat represents the luxury evolution of the QRT-C race seat. The QRT-C Performance Carbon uses the same FIA approved light-weight all-carbon fiber race shell as the QRT-C race seat but is covered in Italian Leather and Alcantara. The QRT-C Performance Carbon is constructed from “Pre-Preg” aerospace grade carbon fiber, also known as Dry Carbon. The seats are handstitched in the Sparco OEM factory in Torino Italy. The QRT-C Performance Carbon has a unique CAD design that features a lower seating position that can fit a larger/taller driver with the exterior dimensions that can fit into smaller cockpits. The QRT-C Performance can hold the driver during extreme lateral forces, but is also comfortable for long road trips. The QRT-C Performance Carbon seat is FIA Approved. SIZING Large – up to a 36” waist (pants size) WHAT IS QRT? Designed and developed at the Sparco OEM Composite Laboratory in Italy, QRT is a patented state-of-the-art technical process, based on aerospace technologies. QRT creates an unparalleled mechanical strength-to-weight ratio. This innovative production method generates the lightest fiberglass composite seat shells currently on the market; in fact, it guarantees a reduction in total weight of up to 30% compared to traditional production methods. The QRT seats approach the weight of a comparable carbon fiber seat at a lower price point. TECHNOLOGY Ultralight Carbon Fober Shell Excellent fitment into small cockpits Medium/Large size driver fitment Excellent ergonomics Fire retardant fabric Special non-slip fabric FIA approved QRT-C PERFORMANCE CARBON DIMENSIONS

Racetech RT4119W Racing Seat Racetech took their most popular seat and gave it a chop! The RT4119W (Wide) and RT4119WT (Wide & Tall) seats are based on the existing RT4119WHR and RT4119WTHR, but with the head restraints removed for improved visibility and access in track day type vehicles. This seat retains Racetech's unique, patented back mount design to give the driver ultimate support and feel for the chassis not available in basic floor-mounted seats. Customize your seat further with low base cushions or add side cushions for support in the thigh area. These 119 seats without head restraints are not FIA homologated. These seats do not include an air ducting spigot, but when it gets hot in your Porsche or Pro Touring Camaro, you're just going to turn on your air-conditioning, right? Ideal for HPDE/DE track cars, off-road desert trucks & outlaw drag cars when drivers can't use a head restraint seat. Brackets and Mounting: Side mount to the floor using Racetech RTB1009M 5mm aluminium brackets (please tick the box above when ordering). Back mount using RTB2115B in conjunction with RTB2005C. The RTB2115B is a 5mm aluminum bracket that bolts directly to the shoulder beam of the seat. The RTB2005C clamps bolt to the RTB2115B (once holes have been drilled) and come in three variants: 1-1/2" (38mm), 1-5/8" (41mm) or 1-3/4" (45mm) ID to suit the rollcage tube diameter in your vehicle. Please select your preferred clamp diameter above when ordering. TECHNICAL INFO: FIA Homologation: N/A Gel-coated in gloss black Seat covered in black fire-retardant fabric Wear patches of black perforated leather Shell construction in composite (GRP) Shell weight from 7.0kg (15.5 lbs) Sizes W (Wide) or WT (Wide & Tall) Air Ducting: N/A Back-mount compatible     

Sparco QRT-K Carbon Kevlar Racing Seat The QRT-K is a full Carbon Kevlar version of the QRT-R. The QRT-K looks amazing with the exposed yellow/black Carbon Kevlar weave. The QRT-K is one of the lightest seats on the market. The QRT-K weighs 13.5lbs fully trimmed (with padding, cover and harness guides) and is constructed from “Pre-Preg” aerospace grade Carbon Kevlar. The QRT-K was specifically designed for a larger driver and it can fit a 36” waist (pants size) driver. The QRT-K is unique because it was designed to fit a larger driver but has excellent fitment into smaller cockpits. The QRT-K requires the special QRT Side mounts (#600QRT) which allows the seat to be raked back for a comfortable ergonomic seating position. The QRT-K is FIA approved. SIZING Large fits up to a 36” waist (pants size) WHAT IS QRT? Designed and developed at the Sparco OEM Composite Laboratory in Italy, QRT is a patented state-of-the-art technical process, based on aerospace technologies. QRT creates an unparalleled mechanical strength-to-weight ratio. This innovative production method generates the lightest fiberglass composite seat shells currently on the market; in fact, it guarantees a reduction in total weight of up to 30% compared to traditional production methods. The QRT seats approach the weight of a comparable carbon fiber seat at a lower price point. TECHNOLOGY Ultralight Carbon Kevlar Composite Shell - 13.5lbs including cover and padding Visible carbon kevlar weave Excellent fitment into small cockpits Large size driver fitment Excellent ergonomics Fire retardant fabric Special non-slip fabric FIA approved QRT-K CARBON KEVLAR DIMENSIONS

Sparco QRT-C Carbon Racing Seat The QRT-C is an all-carbon fiber version of the QRT-R. The QRT-C is the lightest “large” size carbon fiber seat on the market. The QRT-C weighs 12.5lbs (with padding and cover) and is constructed from “Pre-Preg” aerospace grade carbon fiber, also known as Dry Carbon. The QRT-C was specifically designed for a large driver and it fits up to a 36” waist driver comfortably. The QRT-C is unique because it was designed to fit a larger driver but has excellent fitment into smaller cockpits The QRT-C requires the special QRT Side Mounts (#600QRT) which allows the seat to be racked back for a comfortable seating position. The QRT-C is FIA approved. SIZING Large – up to a 36” waist (pants size) WHAT IS QRT? Designed and developed at the Sparco OEM Composite Laboratory in Italy, QRT is a patented state-of-the-art technical process, based on aerospace technologies. QRT creates an unparalleled mechanical strength-to-weight ratio. This innovative production method generates the lightest fiberglass composite seat shells currently on the market; in fact, it guarantees a reduction in total weight of up to 30% compared to traditional production methods. The QRT seats approach the weight of a comparable carbon fiber seat at a lower price point. TECHNOLOGY Ultralight Carbon Fiber  - 12.5lbs fully trimmed weight Excellent fitment into small cockpits Large size driver fitment Excellent ergonomics Fire retardant fabric Special non-slip fabric FIA approved QRT-C CARBON DIMENSIONS

Sparco QRT Performance Racing Seat The Sparco QRT-R was the first seat to feature Sparco’s patented QRT technology. The QRT Performance seat represents the luxury evolution of the QRT-R race seat. The QRT Performance uses the same FIA race shell as the QRT-R race seat but is covered in Italian Leather and Alcantara. The seats are handstitched in the Sparco OEM factory in Torino Italy. The QRT Performance has a unique CAD design that features a lower seating position that can fit a larger/taller driver with the exterior dimensions that can fit into smaller cockpits. The QRT Performance can hold the driver during extreme lateral forces, but is also comfortable for long road trips. QRT TECHNOLOGY Sparco QRT Technology gives an unparalleled mechanical strength/weight ratio for fiberglass composite racing seats. QRT Technology gives an average weight savings of 30% when compared to standard fiberglass technology. The main benefit is that QRT seats approach the weight of carbon fiber seat at the price of a fiberglass composite seat. REQUIRES QRT SIDE MOUNT #600QRT FOR PROPER MOUNTING FEATURES OEM Italian leather and Alcantara QRT technology gives up to 30% weight savings Ultra-light fiberglass composite shell Lower seating position that can fit taller/larger drivers Smaller outer dimensions for improved vehicle fitment Available in Black or Red FIA approved