CMS Performance

CMS Performance Clubsport Roll Bar For Porsche 991 GT3 & GT3RS This Roll Bar Fits The Following Cars: Porsche GT3, 991.1 and 991.2 (2014-2019) Porsche GT3RS, 991.1 and 991.2 (2016-2019) New Ultimate Roll Bar for the Porsche 991 GT3 and GT3RS The CMS Performance Clubsport Roll Bar is a new variant of our incredibly popular GT3/GT3RS roll bar. Re-designed with steel gusseting and high-strength support tubing is added to the top and bottom of the X-brace and to all four corners, the CMS Performance Clubsport Roll Bar takes rigidity and strength to another level. This is the strongest, highest quality bolt-in roll bar on the market for the Porsche 991 GT3 and GT3RS, period. In designing and building the CMS Performance Clubsport roll bar, structural rigidity and impact protection were our primary goals. This roll bar is fully 360o TIG welded, the main tubing is 1.75" Docol R8 Advanced High-Strength Steel. CMS is the only roll bar manufacturer to employ this modern material. The support tubing is Docol R8 as well, and the gussets are machined from steel plate. CMS Performance tailors the GT3/GT3RS Clubsport roll bar to take full advantage of the strongest chassis mounting points in the Porsche 991 GT3/GT3RS . The main roll hoop is X-braced and gusseted, with a single tube cross-bar providing lateral strength that's also used for mounting racing harness shoulder straps. Attention To Detail Is The Hallmark Of CMS Performance The cross-bar on the CMS Performance Clubsport Roll Bar for the Porsche 991 GT3 and GT3RS lets you attach your racing harness shoulder straps at the proper angle (0° to -20° front-to-back) and distance relative to the driver and passenger, regardless of seat position. The CMS Performance Clubsport Roll Bar was designed to leave your rear view unobstructed by additional bracing that other roll bars require due to the use of inferior materials. CMS Performance also features a unique three-piece rear kicker that bolts to the Porsche 991 GT3/GT3RS rear shock towers (where the factory GT3 Cup Car roll cage mounts). These are the strongest rear mounting points, and also add rigidity to the chassis for more precise handling. This kicker design is incredibly strong while also being a breeze to install (typical one-piece designs can be a nightmare to install). The main roll hoop is mounted to your Porsche's steel frame structure beneath the vehicle just like the factory Cup Car cage. Built Like a Tank, Finished Like a Porsche Designed using the same guidelines as a full racing roll cage and fully 360o TIG welded by our chassis fabricators and master welders, the CMS Performance Clubsport Roll Bar for the Porsche 991 GT3 and GT3RS is unsurpassed in quality, durability, and structural integrity. Each roll bar is professionally powder-coated in-house to guarantee fit and finish no other manufacturer can match. This also lets us use powder coat colors we've matched to Porsche GT3 and GT3RS OEM paint colors for a truly customized aesthetic. We also offer custom technical powder coat finishes like the amazing Superchrome! Or you can choose our rich satin black powder coat for a more low-key installation. Powder coating any color you choose is included in the price of your CMS Performance roll bar. Don't Settle For Anything Less Than The Best Thoughtful engineering and design, superior materials, masterful fabrication, and beautifully customized finishing. That's the CMS Performance way of doing things. Backed by our legendary customer service, it all adds up to this: you can pay more for a roll bar, but you can only get the best from CMS. Add Premium Racing Harnesses To Your Porsche Add six-point Schroth Enduro 2x2 GT3, Schroth Flexi 2x2 GT3, or Sabelt Silver Series GT3 racing harness to your order and save! These harnesses are specifically designed for the Porsche 992 GT3 and GT3RS and will bolt to your factory lightweight carbon bucket seats. Or you can add four-point Schroth Profi II ASM GT3 or Sabelt Porsche GT3 4 Point harnesses, ideal for the Porsche 992 GT3 and GT3RS passenger seat that doesn't have a factory sub-strap pass through. With six-point harnesses, we strongly recommend using the CMS Performance Sub Strap Mount to provide a solid, properly located anchor for your anti-submarine straps. The CMS Performance Sub Strap Mount is simple to install at the same time you're installing your roll bar! Straightforward Installation Takes The Headache Out Of Roll Bars We've been through more than a few wrestling matches installing bolt-in roll bars in street cars. Fortunately, we used that experience to design the CMS Performance Roll Bar for the Porsche 992 GT3 and GT3RS to be a lot less frustrating to install. Check out the installation instructions here. We hesitate to go so far as to say it's easy, but we'll say it isn't hard if you have a friend and some basic tools. CMS Performance Roll Bar Details: Manufacturer: CMS Performance Manufacturer Part: RB11-991 Materials: Docol R8 Advanced High-Strength Steel; steel plate gussets. Construction: Full-penetration 360o TIG welded; one-piece gusseted main hoop and three-piece kicker; high-strength double-bolted interlocking roll bar joints and American-made Grade 8 hardware. CNC-cut precision mounting plates Full seat travel with any seat Detailed installation instructions & all necessary hardware for a seamless installation This product is intended for off-road race track use only.

CMS Performance Clubsport Roll Bar For Porsche 992 GT3 & GT3RS This Roll Bar Fits The Following Cars: Porsche GT3, 992 (2022+) Porsche GT3RS, 992 (2023+) New Ultimate Roll Bar for the Porsche 992 GT3 and GT3RS The CMS Performance Clubsport Roll Bar is a new variant of our incredibly popular GT3/GT3RS roll bar. Re-designed with steel gusseting and high-strength support tubing is added to the top and bottom of the X-brace and to all four corners, the CMS Performance Clubsport Roll Bar takes rigidity and strength to another level. This is the strongest, highest quality bolt-in roll bar on the market for the Porsche 992 GT3 and GT3RS, period. In designing and building the CMS Performance Clubsport roll bar, structural rigidity and impact protection were our primary goals. This roll bar is fully 360o TIG welded, the main tubing is 1.75" Docol R8 Advanced High-Strength Steel. CMS is the only roll bar manufacturer to employ this modern material. The support tubing is Docol R8 as well, and the gussets are machined from steel plate. CMS Performance tailors the GT3/GT3RS Clubsport roll bar to take full advantage of the strongest chassis mounting points in the Porsche 992 GT3/GT3RS . The main roll hoop is X-braced and gusseted, with a single tube cross-bar providing lateral strength that's also used for mounting racing harness shoulder straps. Attention To Detail Is The Hallmark Of CMS Performance The cross-bar on the CMS Performance Clubsport Roll Bar for the Porsche 992 GT3 and GT3RS lets you attach your racing harness shoulder straps at the proper angle (0° to -20° front-to-back) and distance relative to the driver and passenger, regardless of seat position. The CMS Performance Clubsport Roll Bar was designed to leave your rear view unobstructed by additional bracing that other roll bars require due to the use of inferior materials. CMS Performance also features a unique three-piece rear kicker that bolts to the Porsche 992 GT3/GT3RS rear shock towers (where the factory GT3 Cup Car roll cage mounts). These are the strongest rear mounting points, and also add rigidity to the chassis for more precise handling. This kicker design is incredibly strong while also being a breeze to install (typical one-piece designs can be a nightmare to install). The main roll hoop is mounted to your Porsche's steel frame structure beneath the vehicle just like the factory Cup Car cage. Built Like a Tank, Finished Like a Porsche Designed using the same guidelines as a full racing roll cage and fully 360o TIG welded by our chassis fabricators and master welders, the CMS Performance Clubsport Roll Bar for the Porsche 992 GT3 and GT3RS is unsurpassed in quality, durability, and structural integrity. Each roll bar is professionally powder-coated in-house to guarantee fit and finish no other manufacturer can match. This also lets us use powder coat colors we've matched to Porsche GT3 and GT3RS OEM paint colors for a truly customized aesthetic. We also offer custom technical powder coat finishes like the amazing Superchrome! Or you can choose our rich satin black powder coat for a more low-key installation. Powder coating any color you choose is included in the price of your CMS Performance roll bar. Don't Settle For Anything Less Than The Best Thoughtful engineering and design, superior materials, masterful fabrication, and beautifully customized finishing. That's the CMS Performance way of doing things. Backed by our legendary customer service, it all adds up to this: you can pay more for a roll bar, but you can only get the best from CMS. Add Premium Racing Harnesses To Your Porsche Add six-point Schroth Enduro 2x2 GT3, Schroth Flexi 2x2 GT3, or Sabelt Silver Series GT3 racing harness to your order and save! These harnesses are specifically designed for the Porsche 992 GT3 and GT3RS and will bolt to your factory lightweight carbon bucket seats. Or you can add four-point Schroth Profi II ASM GT3 or Sabelt Porsche GT3 4 Point harnesses, ideal for the Porsche 992 GT3 and GT3RS passenger seat that doesn't have a factory sub-strap pass through. With six-point harnesses, we strongly recommend using the CMS Performance Sub Strap Mount to provide a solid, properly located anchor for your anti-submarine straps. The CMS Performance Sub Strap Mount is simple to install at the same time you're installing your roll bar! Straightforward Installation Takes The Headache Out Of Roll Bars We've been through more than a few wrestling matches installing bolt-in roll bars in street cars. Fortunately, we used that experience to design the CMS Performance Roll Bar for the Porsche 992 GT3 and GT3RS to be a lot less frustrating to install. Check out the installation instructions here. We hesitate to go so far as to say it's easy, but we'll say it isn't hard if you have a friend and some basic tools. CMS Performance Roll Bar Details: Manufacturer: CMS Performance Manufacturer Part: RB11-992 Materials: Docol R8 Advanced High-Strength Steel; steel plate gussets. Construction: Full-penetration 360o TIG welded; one-piece gusseted main hoop and three-piece kicker; high-strength double-bolted interlocking roll bar joints and American-made Grade 8 hardware. CNC-cut precision mounting plates Full seat travel with any seat Detailed installation instructions & all necessary hardware for a seamless installation This product is intended for off-road race track use only.

CMS Performance Deluxe Bolt-In Harness Bar For C8 Corvette This Harness Bar Fits the Following Cars: 2020+ Chevrolet Corvette Stingray (C8) 2023+ Chevrolet Corvette Z06 (C8) Does not fit Convertible or Roadster Click Here For Installation Instructions The Best C8 Corvette Harness Bar in the World The C8 Corvette is an incredible, affordable track-day car that easily achieves race car performance on track. Managing that kind of performance wearing nothing but a three-point seat belt is a chore and leaves a lot to be desired in terms of safety. That's where we come in with the CMS Performance C8 Corvette Deluxe Harness Bar. Featuring the same rock-solid, high-strength design as our standard C8 Harness Bar, the Deluxe bar adds an innovative "main hoop" design, giving it a more aggressive look. This also gives you a place to mount an in-car motorsports video camera, like the AiM Sports SmartyCam GP HD. Of course, it provides high-strength mounting points for your harness shoulder straps to keep you firmly and safely in your seat. The C8 Deluxe Harness Bar is the strongest, most elegantly designed C8 harness bar on the market. It seamlessly integrates into your C8 interior, preserves your rear view, and gives the C8 a big bump in cool factor, especially with a custom powder-coat color! The CMS C8 Deluxe Harness Bar allows full seat travel while locating your harness shoulder belts at the proper height for maximum on-track safety and security. Installation requires no drilling or other modification of the chassis, and no modification of your upper center console trim. Some modification of your B-pillar lock/seat belt trim panels is required. We offer precision pre-cut panels to ease installation and save your originals if you need to put your C8 back to stock. Corvette C8 Deluxe Harness Bar is Made in the USA Every CMS C8 Deluxe Harness Bar is handcrafted in America by master fabricators for a perfect fit, beautifully 360o TIG welded for high strength, and fully powder-coated in our facility for a brilliant, durable finish. And there's no extra charge for custom colors. CMS operates a complete powder-coating facility to offer you color-matched Corvette factory colors, giving your C8 a customized look that will last. CNC mandrel bent and fully TIG welded from premium Docol R8 Advanced High-Strength Steel (stronger than 4130 CrMo or DOM) and finished in rich powder-coat. Complete, detailed instructions make installation pretty simple (figure about an hour if you're reasonably handy). Add The Best Harnesses For The C8 Corvette Add optional four-point Sabelt Silver Series or Schroth Profi II ASM four-point harnesses along with the CMS Performance Harness Install Kit, and your C8 Corvette is ready to hit the track with significantly upgraded driver and passenger safety. These harnesses were specifically designed for use in street cars with no sub strap pass-through in the seat. CMS Performance C8 Corvette Deluxe Harness Bar Details: Materials: 1.50″ x .095" Docol R8 Advanced High-Strength Steel for superior safety Construction: Full 360o TIG welding for ultimate strength, integrity, and beauty Finish: Custom-color powder coating in any color you can imagine Weight: 24 lbs. (10.9 kg) Features: Unobstructed rear view; designed, built, and finished in the USA, allows full seat travel with any seat Comes with all necessary hardware This product is intended for off-road, race track use only.

CMS Performance Bolt-In Harness Bar For C8 Corvette This Harness Bar Fits The Following Cars: 2020+ Chevrolet Corvette Stingray & Z51 (C8) 2023+ Chevrolet Corvette Z06 (C8) Does Not Fit Convertible / Roadster Click Here For Installation Instructions The Best Harness Bar in the World for the C8 Corvette The C8 Corvette is an incredible, affordable track-day car that easily achieves race car performance on track. Managing that kind of performance wearing nothing but the three-point seat belt is a chore and leaves a lot to be desired in terms of safety. That's where we come in with the CMS Performance C8 Corvette Harness Bar. This provides a rock-solid, high-strength bar to mount shoulder straps for a 4-, 5-, or 6-point racing harness to keep you firmly and safely in your seat. The CMS Performance C8 Harness Bar is the strongest, most elegantly designed C8 harness bar on the market. It seamlessly integrates into your C8 interior, and we custom powder coat it whatever color you choose, including factory color-matched hues. The CMS C8 bar allows full seat travel while locating your harness shoulder belts at the proper height for maximum on-track safety and security. Installation requires no drilling or other modification of the chassis, and only minor modification of your interior trim. You can add our precision pre-cut OEM trim to ease the install, preserving your original trim should you want to put your Corvette back to stock in the future. The C8 Corvette Harness Bar That's Made in America Every CMS harness bar is handcrafted in America by master fabricators for a perfect fit, beautifully 360o TIG welded for high strength, and fully powder-coated in our facility for a brilliant, durable finish. And there's no extra charge for custom colors. CMS operates a complete powder-coating facility to offer you color-matched Corvette factory colors, giving your C8 a customized look that will last. CNC mandrel bent and fully TIG welded from premium Docol R8 Advanced High-Strength Steel (stronger than 4130 CrMo or DOM) and finished in rich powder-coat. Complete, detailed instructions make installation pretty simple (figure about an hour if you're reasonably handy). Installation requires modifying the two lock/seat belt trim panels and the upper trim of your center console. We offer two levels of pre-cut trim to ease installation: first, just the upper console (the most visible and most difficult to trim correctly); second the upper console plus the two lock/seat belt trim panels. Our installation instructions also include cutting templates should you decide to modify your existing trim. Add Harnesses To Complete Your Safety Upgrade Add optional four-point Schroth Profi II ASM or Sabelt Steel Series harnesses along with the CMS Performance Harness Install Kit, and you're ready to hit the track with greatly improved driver and passenger safety. These harnesses were specifically designed for use in street cars with no sub strap pass-through in the seat. CMS Performance C8 Corvette Harness Bar Details: Materials: 1.50″ x .095" Docol R8 Advanced High-Strength Steel for superior safety Construction: Full 360o TIG welding for ultimate strength, integrity, and beauty Finish: Custom-color powder coating in any color you can imagine Weight: 18 lbs. (8.2 kg) Features: Unobstructed rear view; designed, built, and finished in the USA; allows full seat travel with any seat Comes with all necessary hardware This product is intended for off-road race track use only

CMS Performance Harness Install Kit For C7 Corvette This Product Fits The Following Cars: Chevrolet Corvette Stingray & Z51, C7 (2014-2019) Chevrolet Corvette Z06, C7 (2015-2019) Quick and Easy Installation of Harness Lap Belts in the C7 Corvette The CMS Performance Harness Install Kit for the C7 Corvette provides two strong, secure anchors for the lap belts of your racing harness using the factory seats of your C7 Corvette. Each CMS Performance C7 Corvette Harness Install Kit is for one seat (driver or passenger side, the kit works on either seat). Ordering two kits saves you $25 overall and you can install a harness for your passenger or instructor. CMS Performance is 100% Designed and Built in the USA All CMS Performance products are designed, constructed, and finished in our USA manufacturing and powder coating facility. The CMS Performance C7 Corvette Harness Install Kit is CNC cut and fully TIG-welded from high-strength stainless steel, then powder coated a rich satin black to blend seamlessly into your interior when you don't have harnesses installed. Complete detailed instructions make installation straightforward (figure about an hour if you're reasonably handy). Click here for installation instructions. For the C7 Corvette, we recommend the Schroth Profi II ASM or Sabelt Steel Series four-point harnesses for use with this kit. Schroth's proprietary Anti-Submarine (ASM) technology was developed specifically for use in street cars like the C7 Corvette without a sub strap a pass-through in the seats. Sabelt's four point Steel Series offers an alternative that gives you a significant safety upgrade at a reasonable price! CMS Performance Harness Install Kit Details: Manufacturer: CMS Performance manufacturer Part: Harninstall-C7 Construction: 360o TIG welded stainless steel Finish: Satin black powder coat Designed, manufactured, and powder coated by CMS Performance in the USA This product is intended for off-road use only.

CMS Performance Harness Install Kit For C8 Corvette This Product Fits The Following Cars: Chevrolet Corvette Stingray & Z51, C8 (2020+) Chevrolet Corvette Z06, C8 (2023+) Quick and Easy Installation of Harness Lap Belts in the C8 Corvette The CMS Performance Harness Install Kit for the C8 Corvette provides two strong, secure anchors for the lap belts of your racing harness using the factory seats of your C8 Corvette. The kit is typically used along with the CMS Performance C8 Harness Bar or Deluxe C8 Harness Bar. Together they give C8 Corvette driving enthusiasts an elegant, secure way to use a racing harness. Each CMS Performance C8 Corvette Harness Install Kit is for one seat (driver or passenger side, the kit works on either seat). Ordering two kits now, you save $25 and you can install a harness for your passenger or instructor. CMS Performance is 100% Designed and Built in the USA All CMS Performance products are designed, constructed, and finished in our USA manufacturing and powder coating facility. The CMS Performance C8 Corvette Harness Install Kit is CNC cut and fully TIG-welded from high-strength stainless steel, then powder coated a rich satin black to blend seamlessly into your interior when you don't have harnesses installed. Complete detailed instructions make installation straightforward (figure about an hour if you're reasonably handy). Click here for installation instructions. For the C8 Corvette, we recommend the Schroth Profi II ASM Harness for use with this kit. Schroth's proprietary Anti-Submarine (ASM) technology was developed specifically for use in street cars like the C8 Corvette that don't have a pass-through in the seat cushions to accommodate the sub straps of a six-point racing harness. CMS Performance Harness Install Kit Details: Manufacturer: CMS Performance manufacturer Part: Harninstall-C8 Construction: 360o TIG welded stainless steel Finish: Satin black powder coat Designed, built, and powder coated in the USA This product is intended for off-road use only.

CMS Performance Harness Install Kit For Gen 6 Camaro This Product Fits The Following Cars: Chevrolet Camaro Coupe, all (2016+) Quick, Easy Installation of Harness Lap Belts in the Gen 6 Camaro The CMS Performance Harness Install Kit for the Gen 6 Camaro provides two strong, secure anchors for the lap belts of your racing harness using the factory seats of your Gen 6 Camaro. Each CMS Performance Gen 6 Camaro Harness Install Kit is for one seat (driver or passenger side, the kit works on either seat). Ordering two kits saves you $25 overall and you can install a harness for your passenger or instructor. CMS Performance is 100% Designed and Built in the USA All CMS Performance products are designed, constructed, and finished in our USA manufacturing and powder coating facility. The CMS Performance Gen 6 Camaro Harness Install Kit is CNC cut and fully TIG-welded from high-strength stainless steel, then powder coated a rich satin black to blend seamlessly into your interior when you don't have harnesses installed. Complete detailed instructions make installation straightforward (figure about an hour if you're reasonably handy). Click here for installation instructions. For the Gen 6 Camaro, we recommend the Schroth Profi II ASM or Sabelt Steel Series four-point harnesses for use with this kit. Schroth's proprietary Anti-Submarine (ASM) technology was developed specifically for use in street cars like the Gen 6 Camaro without a sub strap a pass-through in the seats. Sabelt's four point Steel Series offers an alternative that gives you a significant safety upgrade at a reasonable price! CMS Performance Harness Install Kit Details: Manufacturer: CMS Performance manufacturer Part: Harninstall-G6C Construction: 360o TIG welded stainless steel Finish: Satin black powder coat Designed, manufactured, and powder coated by CMS Performance in the USA This product is intended for off-road use only.

CMS Performance Bolt-In Harness Bar for Porsche 981 & 718 Cayman This Harness Bar Fits The Following Cars: Porsche Cayman (2014+) Porsche Cayman S (2014+) Porsche Cayman GTS (2015+) Porsche Cayman GT4 (2016+) Porsche Cayman GT4 RS (2022+) High Strength Bolt In Harness Bar For Your Porsche Cayman Expertly crafted from high-strength, fully TIG welded Docol R8 Advanced High-Strength Steel tubing, the CMS Performance Porsche Cayman Harness Bar is the strongest, lightest, and safest bolt-in harness bar on the market for your Porsche 981 Cayman. It gives you the perfect attachment for your five- or six-point harness shoulder straps without having to install a full roll bar. The CMS Performance Porsche Cayman Harness Bar is designed to place your racing harness shoulder straps at the proper angle (0° to -20°) and distance (eight inches or less) so the driver and passenger racing harnesses function properly. There is no need to cut your Porsche Cayman's carpeted central hump, a design unique to CMS Performance that provides an ideal location for mounting an AiM SmartyCam. The CMS Performance Porsche Cayman Harness Bar also gives you full access to the engine cover. It mounts to the frame structure across the passenger compartment bulkhead, directly behind the seats. Click Here For Installation Instructions Made In The USA For The Ultimate In Quality And Precision The CMS Performance Porsche Cayman Harness Bar is meticulously designed, fabricated, and fully TIG welded by CMS Performance master fabricators for unsurpassed integrity, fit, and finish. The harness bar comes standard in a smooth satin black powder coat to complement any interior. Or you can choose from any number of custom powder coat colors matched to most factory Porsche paint colors. To install the CMS Performance Porsche Cayman Harness Bar, some modification of your OEM interior trim will be required. CMS Performance offers precision-cut OEM Porsche trim as an option to ease installation and preserve your original interior pieces. Features Of The CMS Performance Porsche Cayman Harness Bar: 1.50″ x .120" Docol R8 Advanced High-Strength Steel No cutting of carpeted center hump preserves expensive OEM carpet CNC-cut mounting plates Designed and built in the USA Allows full seat travel with any seat Easy to install with perfect fitment guaranteed Detailed Installation Instructions and all necessary hardware included

CMS Performance Bolt In Roll Bar For BMW E92 M3 This Roll Bar Fits the Following Cars: BMW E92 M3 (2008-2013) BMW E92 M3 Competition Package ZCP (2011-2013) BMW E92 M3 GTS (2011) The Premium Roll Bar for BMW's Legendary E92 The CMS Performance Roll Bar is the strongest, safest, most beautifully constructed bolt-in roll bar on the market for the BMW E92 M3. It is engineered to easily bolt into any E92 variant, giving you rollover protection while adding to the motorsport-derived style of the E92 M3. Engineered with a premium put on safety and structural rigidity, the exceptional design of the CMS Performance E92 M3 Roll Bar integrates perfectly with the car's luxury/sport interior. CMS uses only advanced Docol R8 Advanced High-Strength Steel tubing throughout each roll bar, giving you unequalled tensile strength, energy dissipation, and occupant protection. Docol R8 is 15% stronger than 4130 CrMo steel and 30% stronger than mild (DOM) steel used by other roll bar manufacturers. It is superior in every way: resistance to deformation, weld strength, and energy dissipation. A Roll Bar Design as Bulletproof as the M3 Itself CMS Performance designed the E92 roll bar with a one-piece main roll hoop featuring reinforced X-bracing along with a horizontal harness bar. (X-brace gussets can be added as an option add even more strength and rigidity.) The harness bar is specifically designed to locate racing harness shoulder straps at the proper angle (0° to -20°) in most seating positions. Every CMS Performance E92 M3 roll bar bolts directly to the BMW's chassis, forming the rock-solid backbone of your roll-over and impact protection. Rearward kicker support angles are optimized for structural integrity and easy installation, while preserving your unobstructed rear view.  Cuting Edge Materials and Direct Bolt-In The CMS Performance BMW E92 M3 Roll Bar is designed to bolt directly to the M3 chassis' strong points without the need for any modification of existing interior trim or use of backing plates underneath the car. Full 360o TIG welding throughout gives every CMS Performance roll bar unsurpassed strength and durability. Each roll bar includes custom powder coating in your choice of matched BMW M3 factory colors. We also offer technical color powder coat finishes like the amazing Superchrome! Or, go with satin black for a more understated appearance. CMS Performance has over 5,000 custom powder coat colors to give you a truly customized look. The Best Materials, Design and Construction Set CMS Performance Apart Our unwavering focus on using cutting-edge materials, unsurpassed design and construction, and premium fit&finish has taken CMS Performance Roll Bars to the top of the industry. The BMW E92 M3 roll bar is the latest addition to our growing catalog, bringing safety, integrity, and beauty to your M3 whether on the street or at the track! Click Here for Installation Instructions BMW E92 M3 Roll Bar Options: Main hoop X-brace gussets can be added for $200 CMS Roll Bar Harness Collars help keep your harness shoulder straps where you want them CMS Performance BMW E92 M3 Roll Bar Details: Manufacturer: CMS Performance Manufacturer part no.: PRB158 Material: 1.75″ X .090" Docol R8 Advanced High Strength Steel tubing Design: one-piece main hoop and three-piece kickers ease installation Hardware: American-made Grade 8 hardware included BMW E92 M3 Roll Bar Features: CNC-cut mounting plates Designed, built, and finished by CMS Performance in the USA American-made CNC machined solid steel interlocking joints Allows full seat travel with virtually any seat Detailed installation instructions Installation requires removal of the factory rear seat bottom cushion. This product is intended for off-road race track use only.

CMS Performance Bolt In Roll Bar For BMW F87 M2 This Roll Bar Fits the Following Cars: BMW M2 (N55) 2016-2018 BMW M2 Competition (S55) 2019-2020 BMW M2 CS 2020-2022 The Strongest and Safest Roll Bar for the BMW F87 M2 The CMS Performance Roll Bar is the strongest, safest, most beautifully constructed bolt-in roll bar on the market for the BMW M2, M2 Competition, and M2 CS. Engineered with a premium on safety and structural rigidity, the exceptional design integrates perfectly with the M2's luxury/sport interior. CMS uses only advanced Docol R8 Advanced High-Strength Steel tubing throughout each roll bar, giving you unequalled tensile strength and occupant protection. Docol R8 is 15% stronger than 4130 CrMo steel and 30% stronger than mild (DOM) steel used in other bolt-in roll bars. It is superior in every way: resistance to deformation, weld strength, and energy dissipation. Our one-piece main hoop with fully-integrated X-bracing and harness bar bolts directly to the chassis, forming the backbone of the CMS Performance Roll Bar. Rearward "kicker" supports are optimized for support in a roll-over event while maintaining an unobstructed rear view. The harness bar is specifically designed to locate racing harness shoulder straps at the proper angle (0° to -20°) to the driver's shoulders regardless of seat position. Cutting Edge Materials and American-Made Craftsmanship The CMS Performance BMW M2 Roll Bar is designed to bolt directly to the M2 chassis strong points without the need for any modification of existing interior trim or use of backing plates. Adding a CMS custom designed rear seat delete gives the whole installation a clean, factory appearance. Full 360o TIG welding throughout gives the CMS Performance Roll Bar unsurpassed strength and durability. Each roll bar includes custom powder coating in your choice of matched M2 factory colors. You can choose an amazing technical color like Superchrome! Or satin black for a more stealthy appearance. We have over 5,000 custom powder coat colors for a truly customized look. Our unwavering focus on using cutting-edge materials, unsurpassed design & construction, and premium fit & finish has taken CMS Performance Roll Bars to the top of the industry. The BMW M2 roll bar is the latest addition to our growing catalog, bringing safety, integrity, and beauty to customers taking their M2 to the track! Click Here For Installation Instructions BMW F87 Roll Bar Options: CMS premium Rear Seat Delete Kit is custom-designed for the F87 M2, giving your roll bar installation a factory-finished look. CMS Roll Bar Harness Collars help keep your harness shoulder straps where you want them. CMS Performance BMW F87 M2 Roll Bar Details: Manufacturer: CMS Performance Manufacturer part no.: PRB512 Materials: 1.75″ X .090" Docol R8 Advanced High Strength Steel tubing throughout Construction: One-piece main hoop and three-piece kickers ease installation while maintaining exceptional strength Included hardware: Grade 8, American made BMW F87 Roll Bar Features: Optional premium custom-designed rear seat delete for a factory-finished appearance Precision-cut mounting plates Designed, manufactured, and finished in the USA American-made CNC machined solid steel interlocking joints Allows full seat travel with virtually any seat Comes with detailed installation instructions Installation requires removal of the factory rear seats. A rear seat delete kit is recommended but not required for roll bar installation. This product is intended for off-road race track use only.

CMS Performance Bolt In Roll Bar For BMW G87 M2 (2023+) The Premium Roll Bar for the Incredible New M2 Introducing the CMS Performance Roll Bar for the all-new, amazing G87 M2!  The powerful new M2 promises to be a hoot on the track-day circuit, so we got to work right away engineering a bolt-in roll bar that lives up to Competition Motorsport's tradition of building the strongest, safest, most beautifully constructed roll bars on the market. The new CMS Performance roll bar for the G87 delivers on all points! An M2 Roll Bar Engineered For Performance and Safety Conceived from the ground up with a premium on safety and structural rigidity, the exceptional design of the CMS Performance M2 roll bar integrates perfectly with the M2's luxury/sport interior. CMS uses advanced Docol R8 Advanced High-Strength Steel tubing throughout our roll bars, giving you unequalled tensile strength and occupant protection. Docol R8 is 15% stronger than 4130 CrMo steel and 30% stronger than mild (DOM) steel used in other bolt-in roll bars. It is superior in every way: resistance to deformation, weld strength, and energy dissipation. The one-piece main hoop with fully-integrated X-bracing and harness bar bolts directly to the M2 chassis, forming the backbone of the CMS Performance roll bar. Rearward kicker supports are optimized for support in a roll-over event while maintaining an unobstructed rear view. The harness bar is specifically designed to locate racing harness shoulder straps at the proper angle (0° to -20°) to the driver's shoulders regardless of seat position. Click Here For Installation Instructions Cutting Edge Materials and American Made Craftsmanship The CMS Performance BMW M2 Roll Bar is designed to bolt directly to the M2 chassis strong points without the need for any modification of existing interior trim or use of backing plates. Adding a CMS custom designed rear seat delete gives the whole installation a clean, factory appearance. Full 360o TIG welding throughout gives the CMS Performance Roll Bar unsurpassed strength and durability. Each roll bar includes custom powder coating in your choice of matched G87 M2 factory colors. Or go with a custom technical color like the amazing Superchrome (check it out in the photos above!) We have access to over 5,000 powder coat colors, so if you need a color not on the list, just give us a call and we'll make sure your M2 roll bar has the look you like! A Beautiful Beast of a BMW M2 Roll Bar Our unwavering focus on using cutting-edge materials, unsurpassed design & construction, and premium fit & finish has taken CMS Performance roll bars to the top of the industry. The BMW G87 M2 roll bar is the latest addition to our growing catalog, bringing safety, integrity, and beauty to customers taking their new M2 to the track. CMS Performance BMW M2 Roll Bar Options: The optional CMS Performance Rear Seat Delete Kit is custom-designed for the G87 M2, giving your roll bar installation a factory-finished look. Add Schroth Profi II ASM or Sabelt Steel Series four-point harnesses give you increased on-track safety using your factory BMW seats. CMS Roll Bar Harness Collarshelp keep your harness shoulder straps located right where you want them. CMS Performance BMW M2 Roll Bar Details: Materials: 1.75″ X .090" Docol R8 Advanced High Strength Steel throughout (stronger than 4130 CrMo) Construction: fully TIG welded one-piece main hoop and three-piece kickers ease installation while maintaining exceptional strength Precision-cut mounting plates Designed, manufactured, and finished in the USA CNC machined high-strength-steel interlocking joints Allows full seat travel with virtually any seat All USA-made Grade 8 hardware included Detailed installation instructions Installation requires removal of the factory rear seats. This product is intended for off-road race track use only.

CMS Performance Bolt-In Roll Bar For Chevy Camaro (Gen 5) Installation Instructions Here This Roll Bar Fits the Following Cars: Chevy Camaro Coupe (2010-2015), All Does not fit the Camaro Convertible The Strongest Roll Bar Available for the Gen 5 Camaro The CMS Performance Gen 5 Camaro Roll Bar is the strongest, safest, and most beautifully constructed roll bar on the market. In designing the Camaro roll bar, safety, strength, and structural integrity were our primary goals. Fully TIG welded from Docol R8 Advanced High-Strength Steel allows us to design a roll bar that is stronger and lighter! Our innovative design maximizes the room for the factory Recaro seats, meaning taller drivers can send their seat all the way back and still maintain a comfortable recline. Precision CNC machined solid steel interlocking roll bar clamps on the kicker mounting plates help make installation a snap. Free custom powder-coating gives you a premium, finished look without breaking the budget. Add the optional custom-cut Rear Seat Delete Kit and you've got a fully trimmed-out roll bar installation that performs as great as it looks. Our Camaro roll bar forms the perfect foundation for taking your safety up a huge notch. Roll Bar Safety and Strength Are The Priority Safety is the main reason to install a roll bar in the first place. As racers ourselves, we sweat the details. That's why we use 1.75" x .095" Docol R8. Docol is 15% stronger than 4130 CrMo, and much less brittle. Docol R8 also dissipates impact energy more effectively. It's the same tubing used in full-competition road racing roll cages because, first and foremost, it's a roll bar not a trim piece. Our beefy main hoop straddles the rear seat cross member, a much stronger location than the rear footwell, eliminating the need for underbody backing plates. Taking a cue from NHRA cage design, the diagonal supports feature a concave design to allow full front-seat travel while distributing roll-over energy between the main hoop and kickers. The harness cross-bar is precisely located to put your shoulder straps at both the proper angle (0° to -20°) and distance to the driver. Finally our rear kickers bolt to a reinforced corner of the rear seat floor, again requiring no backing plates beneath the floor pan. Objects in Your Rear View Mirror are Clearly Visible A clear rear view is an important component of safety both on and off the race track. Our use of stronger materials and innovative design lets us keep your rear view unobstructed by additional bracing. This also helps weight down. Every detail of the CMS Gen 5 Camaro roll bar is engineered with safety as our primary goal. American-Made Roll Bar for an American Icon Okay, another reason we install roll bars is that they look cool. We're gear heads, we get that. Each CMS Performance Gen 5 Camaro roll bar is handcrafted right here in America by master fabricators for a perfect fit, beautifully 360o TIG welded for high strength, and fully powder-coated in our facility for a brilliant, durable finish. There's no extra charge for custom colors. CMS operates a complete powder-coating facility to offer you color-matched Camaro factory colors, giving your Camaro a personalized look that will last. None of your interior trim panels need to be eliminated or cut. Your rear seat back can be re-installed, or you can opt for our custom Shrader rear seat delete, the perfect place to put a track bag, helmet and HANS, driver cooling system, etc. (you can hide stuff under there, too). If you ever want to put your car back to stock, it will go back together as though the roll bar was never there. Complete, detailed instructions make installation pretty simple (figure about two hours if you're reasonably handy), and all Grade 8 hardware needed is shipped with your CMS roll bar. Add Racing Harnesses and a Head-And-Neck Restraint and and you're ready to hit the track safe and secure. CMS Performance Gen 5 Camaro Roll Bar Details: Manufacturer: CMS Performance Manufacturer part no.: PRB411 Material: 1.75″ x .095" Docol R8 Advanced High-Strength Steel tubing Construction: fully 360o TIG welded Design: one-piece main hoop/kicker with detachable kicker feet Weight: 51 lbs. (23.2 kg) Rear seat delete: custom-made Shrader rear seat delete (optional) Gen 5 Camaro Roll Bar Features: Precision CNC-cut mounting plates Designed, built, and powder-coated in the USA American-made CNC machined solid steel interlocking clamps Allows full seat travel with any seat Straightforward installation and perfect fitment Comes with all necessary Grade 8 American-made hardware This product is intended for off-road race track use only.

CMS Performance Bolt-In Roll Bar For Chevy Camaro (Gen 6) This Roll Bar Fits The Following Cars: 2016+ Chevy Camaro Coupe (all) The Strongest Roll Bar Available for the Gen 6 Camaro The CMS Performance Camaro Roll Bar is the strongest, safest, and most beautifully constructed roll bar on the market. In designing the Camaro roll bar, safety, strength, and structural integrity were our primary goals. Fully TIG welded from Docol R8 Advanced High-Strength Steel allows us to design a roll bar that is stronger and lighter! Our innovative design maximizes the room for the factory Recaro seats, meaning taller drivers can send their seat all the way back and still maintain a comfortable recline. Precision CNC machined solid steel interlocking roll bar clamps on the kicker mounting plates help make installation a snap. Free custom powder-coating gives you a premium, finished look without breaking the budget. Add the optional custom-cut Rear Seat Delete Kit and you've got a fully trimmed-out roll bar installation that performs as great as it looks. Our Camaro roll bar forms the perfect foundation for taking your safety up a huge notch. Designed for Incredible Strength and Safety Safety is the main reason to install a roll bar in the first place. As racers ourselves, we sweat the details. That's why we use 1.75" x .095" Docol R8. Docol is 15% stronger than 4130 CrMo, and much less brittle. Docol R8 also dissipates impact energy more effectively. It's the same tubing used in full-competition road racing roll cages because, first and foremost, it's a roll bar not a trim piece. Our beefy main hoop straddles the rear seat cross member, a much stronger location than the rear footwell, eliminating the need for underbody backing plates. Taking a cue from NHRA cage design, the diagonal supports feature a concave design to allow full front-seat travel while distributing roll-over energy between the main hoop and kickers. The harness cross-bar is precisely located to put your shoulder straps at both the proper angle (0° to -20°) and distance to the driver. Finally our rear kickers bolt to a reinforced corner of the rear seat floor, again requiring no backing plates beneath the floor pan. Objects in the Rear View Mirror Are Clear A clear rear view is a big part of safety both on and off the race track. Our use of very high-strength materials and innovative design lets us keep your Camaro's rear view unobstructed by unnecessary bracing. This also helps the overall weight of the CMS Performance roll bar down. Every detail of the CMS Performance CMS Gen 6 Camaro roll bar is engineered with safety as the primary goal. An American-Made Roll Bar for an American Icon Okay, another reason to install a roll bar in a car like the Gen 6 Camaro is that they look cool. We're gear heads, we get that. Each roll bar is handcrafted right here in America by master fabricators for a perfect fit, beautifully 360o TIG welded for high strength, and fully powder-coated in our facility for a brilliant, durable finish. There's no extra charge for custom colors like the amazing, brilliant Superchrome! CMS operates a complete powder-coating facility to offer you color-matched Camaro factory colors, giving your Camaro a personalized look that will last. None of your interior trim panels need to be eliminated or cut. Your rear seat back can be re-installed, or you can opt for our custom-made Shrader rear seat delete, the perfect place to put a track bag, helmet and HANS, driver cooling system, etc. (you can hide stuff under there, too). If you ever want to put your car back to stock, it will go back together as though the roll bar was never there. Complete, detailed instructions make installation pretty simple (figure about two hours if you're reasonably handy), and all Grade 8 hardware needed is shipped with your CMS roll bar. Add Racing Harnesses and a Head-And-Neck Restraint and and you're ready to hit the track safe and secure. Click Here For Installation Instructions CMS Performance Gen 6 Camaro Roll Bar Details: Manufacturer: CMS Performance Manufacturer part no.: PRB412 Materials: 1.75″ X .095" Docol R8 Advanced High-Strength Steel Construction: Full 360o TIG welding throughout Design: One-piece main hoop/kicker design with detachable kicker feet for installation Weight: 51 lbs. (23.2 kg) Gen 6 Camaro Roll Bar Features: Custom-made rear seat delete available Precision CNC-cut mounting plates Designed, built, and powder-coated in the USA American-made CNC machined steel interlocking roll bar clamps ease installation Allows full seat travel with any seat Straightforward installation and perfect fitment Comes with all necessary hardware This product is intended for off-road race track use only.

CMS Performance Roll Bar for Mustang S197 2005 - 2014 This Roll Bar Fits the Following Cars 2005 -2014 Ford Mustang coupe, all (S197) Click here for installation instructions The Best S197 Mustang Roll Bar on the Market The CMS Performance Mustang Roll Bar is the strongest, safest, and most beautifully constructed roll bar on the market. In designing our Mustang roll bar, safety, strength, and structural integrity were our primary goals. That's why it is fully TIG welded from ultra-strongDocol R8 Advanced High-Strength Steel sized 1.75" diam x .095" wall, vs. the mild-steel tubing others use. Docol R8 is 30-35% stronger than DOM mild steel and even 10-15% stronger than 4130 CrMo steel. This allowed us to design a roll bar that is both stronger and lighter. Precision CNC machined interlocking roll bar clamps, made to our specifications in the USA, make joining the main hoop and kickers easier during installation while giving the CMS Performance roll bar a premium, finished look. CMS Peformance Roll Bar is the Standard for Safety Let's face it, safety is the primary reason to install a roll bar in the first place. So the CMS Performance Mustang Roll Bar is designed to place your harness shoulder straps at both the proper angle (0° to -20°) and distance to the driver. The rear kickers bolt to a strong existing bulkhead, requiring no reinforcement plates beneath the floor pan. Our use of state-of-the-art Docol ultra-high-strength-steel tubing throughout allows us to keep the driver's rear view unobstructed by diagonal braces, which also keeps weight down. Every detail is engineered with safety and structural integrity as our primary goal. American-Made Cool for an Iconic American Car The other reason to install a roll bar is because it really complements the aggressive, race-inspired styling of the Mustang. We get that. So each bar is crafted by hand by master fabricators, TIG welded for the ultimate in durability, and custom powder coated in our facility (at no extra charge). We've color-matched powder to most of Ford's factory paint colors for a truly customized look, or you can choose from thousands of custom colors and finishes to give your car a personalized look that will last. Going from raw Docol tube stock to a gleaming finish, every roll bar is handcrafted by our most experienced cage- and race car builders. Nothing is left to chance. The CMS roll bar is designed to give you an unobstructed view through your rear window. None of your plastic interior trim needs to be removed or cut, just a little carpet that is hidden away. So if you ever need to put your car back to stock, it will look as though the roll bar was never there. Complete, detailed instructions make installation pretty simple (figure about two hours if you're reasonably handy; having a buddy helps!) All the supplied installation hardware is American made: Grade 8 mounting hardware and an industrial carbide drill bit. So you don't have worry that you don't have what you need for a flawless installation. You can add four-point or six-point harnesses to your Mustang (depending on the seats you're using) using the drop-downs above. Many customers also add CMS Locking Harness Collars to keep harness shoulder straps right where you want them (they're not required for safety, but a lot of people like the look!). CMS Performance Mustang Roll Bar Details: Materials: 1.75″ X .095" Docol R8 Advanced High-Strength Steel tubing Construction: Fully TIG welded for ultimate strength, integrity, and beauty. Design details: One-piece main hoop and three-piece rear kicker make installation simpler. Weight: 52 lbs. (23.6 kg) CNC-cut mounting plates. Designed, built, and powder-coated by CMS Performance in the USA. CNC machined high-strength steel interlocking clamps ease installation. Allows full seat travel with any seat. Straightforward install and perfect fitment, guaranteed. Includes all necessary hardware including carbide drill bit. Roll bar installation in the Mustang requires removal of the rear seats. This product is intended for off-road race track use only.

CMS Performance Bolt-In Roll Bar For Porsche 987 Cayman This Roll Bar Fits The Following Cars: 2006-2012 Porsche 987 Cayman S 2007-2012 Porsche 987 Cayman 2011-2012 Porsche 987 Cayman R Hands Down the Best Roll Bar for the Porsche 987 Cayman The CMS Performance Roll Bar is the strongest, safest, and most beautifully constructed roll bar on the market for your Porsche 987 Cayman (base, S, GTS, or R). In designing our roll bar, safety and structural rigidity were our primary goals. That's why we use 1.75" x .095" premium Docol R8 Advanced High-Strength Steel tubing, vs. the weaker, more brittle 4130 tubing others use. Attention to Detail Befitting the Porsche 987 At CMS Peformance, meticulous attention to detail defines the design of our Porsche 987 Cayman Roll Bar. We make sure to locate your harness shoulder straps at the proper angle (0° to -20°) and distance relative to the driver, regardless of seat position. Our unique design provides an ideal mount for a Smarty Cam video camera. Our use of thicker state-of-the-art Docol tubing throughout allows us to keep the driver's rear view unobstructed by diagonal bracing, giving you unfettered access to the engine cover with the roll bar in place. (Our competitors make you remove part of your roll bar to get at your engine, risking damage to the bar and your interior!) The CMS Performance 987 Cayman Roll Bar uses high-strength kickers bolted to the Cayman's rear shock towers, the safest, strongest mounting points. This allows the roll bar to contribute rigidity to your chassis and suspension. The main roll hoop is mounted to the frame structure across the rear bulkhead for light weight and superior strength. Built Like A Tank, Finished Like A Porsche Each CMS Performance Porsche 987 Cayman Roll Bar is fully powder coated in your choice of custom-matched Porsche's 987 colors for a truly unique look. We also offer technical colors like the amazing Superchrome! Or you can choose a more stealthy installation with our rich satin black powder coat. Fully 360o TIG welded by our master craftsmen using superior materials, then custom powder coated in-house by CMS Performance. The design, strength, fit, and finish of the CMS roll bar add up to this: you can spend more on a roll bar, but you only get the best from CMS. Click Here For Installation Instructions CMS Performance Porsche 987 Cayman Roll Bar Details: Manufacturer: CMS Performance Manufacturer part no.: PRB117 Materials: 1.75" X .095" Docol R8 Advanced High-Strength Steel tubing Construction: full 360o TIG welding for durability, strength, and beauty Design: one-piece main hoop with full engine access without removal of any part of the roll bar Minimal cutting of trim required, for a factory-installed look CNC-cut mounting plates Designed, built, and finished by CMS Performance in the USA American-made CNC machined high-strength steel interlocking clamps Allows full seat travel with any seat Straightforward installation and perfect fitment All American-made hardware included This product is intended for off-road race track use only.