AIM SmartyCam 3 Dual Video Camera - The Ultimate Trackside Companion
AiM Sports AiM Sports SmartyCam 3 Dual Data Logger Camera $3,000.00
AiM Sports SmartyCam 3 Dual Data Logger Camera One AiM SmartyCam Is Great, But Two Are Better! The AiM SmartyCam 3 Dual is a true dual-lens HD motorsports camera and data logger, designed for the extraordinary rigors of race track competition. Taking the best features of the SmartyCam 2.1 and 2.2 GPHD, the SmartyCam 3 Dual brings two full HD images from independent cameras at a resolution of 1920x1080 pixels and a crystal-clear 60 fps. Dual Motorsports Cameras The SmartyCam 3 Dual features two separate bullet cameras that are easily placed anywhere in the cockpit with the included 2M (6.6 ft) SMA cables. SMA cables are small, shielded, and feature threaded connections on each end for the best in video data in the harshest of race conditions. Video Streaming Output SmartyCam 3 Dual features a video streaming output channel with SDI interface. Your 3G-SDI format video and audio stream is now able to be sent to a data streamer at your choice of 30 or 60 fps. Live data streaming has never been easier. AiM RaceStudio 3: The Benchmark in Video Racing Analysis AiM RaceStudio 3 software is included to allow you to customize and configure your overlays in a virtually infinite variety of ways. You can easily add your team logo, sponsor information, track map or graphic objects from a list of pre-determined sets with the same layout or single objects from different sets, This could even be adding your second camera video in Picture-In-Picture mode with your team logo and a track map showing. AiM RaceStudio 3 is powerful and fully customizable for your team and sponsor needs. Your entire video session can also be split easily. Individual videos of separate laps can now be simultaneously viewed side-by-side to identify best race line and lowest lap time. The "Share And Compare" feature lets you compare video of your best lap alongside your friend's or teammate's personal best. AiM RaceStudio 3 makes lower lap times a whole lot easier to achieve. Internal Data Logger Built-in The SmartyCam 3 Dual has a second ECU CAN interface allowing for CAN expansions without the need for an ECU bridge. Both your video and CAN data is stored on a standard removable SD card (not included) with capacity of up to 2TB, with all data stored in the mp4 file format. At the end of your stint or session, your SD card contains all the information you need for a deep data dive, helping you find the tweaks needed for lower lap times. Designed for the Extremes of Motorsports The SmartyCam 3 Dual is a true motorsports camera protected by a solid aluminum housing with a hard anodized finish. Built for the rigors of racing with an IP65 waterproof rating, the SmartyCam 3 Dual is at home in your Porsche GT3 Cup, Super Trofeo, TA2 Camaro, F4, or 125cc Shifter Kart. Whatever you drive, you can trust the AiM SmartyCam 3 Dual to get you great video and data. Automatic Start & Stop Easy integration and automation with your AiM family of data components. The SmartyCam 3 Dual can be set up to automatically power on, start recording, stop recording, lock your data and video file and power down. Focus on your competition, not your proven data system. No "Wave Effect" with Global Shutter CMOS Solid motor mounts, straight cut gearboxes, and high-revving race engines affect most wave type shutter systems found on ordinary action video cameras. If you have ever seen a video that gets wavy and wobbly at high RPMs, you've seen the limits of wave shutters. The AiM SmartyCam 3 Dual uses a solid CMOS Global Shutter to provide quality, crisp, clear videos even in the most aggressive race cars. High Quality Video in a Small File Size Optimized video compression in H.264 allows a more compact video file size for the perfect balance of file size and video quality. Full HD is accomplished without the massive file sizes normally required. Championship World Racing League, SRO, and ChampCar teams swap video cards at every practice, qualifying, and race pit stop. This data is only readable after it's uploaded, so the H.264 allows for a faster data download of your driver and vehicle performance as well as vehicle health. AiM Sports SmartyCam 3 Dual Data Logger Camera Details: Manufacturer: AiM Manufacturer part number, 67°: XS3DB6767L2L200 Manufacturer part number, 84°: XS3DB8484L2L200 Manufacturer part number, 120°: XS3DB120120L2L200 Video format: H.264 compression; 1920x1080 pixels @ 60 fps Display resolution: 2.4 inches, 240x320 pixels Lens: Low distortion camera lens (x2) CMOS Sensor: Global shutter Field-of-view: choose 67°, 84° or 120° Internal battery: Rechargeable lithium battery Video out: 3G-SDI External power: 9V to 15V Supported MicroSD Card (not included): up to 2TB Usage temperatures: -10°C to 50°C (14°F to 122°F) Auto Power On/Off: Yes Auto Start/Stop Recording: Yes Body construction: anodized aluminum Dimensions (main unit): 154.4 x 109.6 x 42.0 mm (6.1 x 4.3 x 1.7 in) Dimensions (bullet camera): ø 24 mm x 48.2 mm Connectors: Deutsch 22 pin (x1); SMA SDI Video out (x1); SMA bullet connection (x2); USB-C (x1) Bullet camera cable length: 2M (6.6 ft) Weight: main unit, 800g (1.8 lb); bullet camera (each) 45g (1.6 oz) Waterproof: IP65
AiM Sports MXG 1.2 Large Color TFT Dash and Data Logger
AiM Sports AiM Sports MXG 1.2 Large Color TFT Dash and Data Logger from $2,899.00
AiM MXG 1.2 Large Color TFT 7" Dash & Data Logger The AiM MXG 1.2 data-logging dash represents a huge leap forward in racing display flexibility. The brilliant 800x480 pixel, 7.0" color TFT display frees you from the constraints of a single, factory-designed dash display. The MXG shows you the data you want, the way you want in brilliant, high-contrast color. The MXG 1.2 is a large, brilliant dashlogger designed to acquire and display data coming from your ECU, an internal accelerometer and gyro, the included GPS08 Module, analog/digital inputs and pre-defined math channels. Performance data acquired can be expanded by adding up to eight expansion modules (sold separately). The large 7" high-color display makes it perfect for installation in wider cockpits (like in touring and GT cars). CONFIGURABLE PAGES You can define all the custom pages you wish, choosing from a large library of page styles and colors, defining which data you want to see and where (including end of scale and units of measure). Swapping between pages is as easy as pushing one or two buttons! INPUT/OUTPUT FLEXIBILITY Eight fully configurable analog input channels can sample, log, and display a wide range of temperatures, pressures, and potentiometers (throttle position, steering wheel position, etc). CAN Inputs allow you to further expand the dash by adding an almost limitless number of AiM CAN Data Hubs (Part No. MC-329, sold separately). These hubs let you connect other inputs such as Lambda Controller (O2), SmartyCam, or even channel expansion hubs, without using any analog channels. A separate CAN Output allows you to send messages to the existing CAN network, adding to the vehicle system control possibilities! The MXG 1.2 can also be connected to many different ECUs to log data gathered by each ECU. An internal three-axis accelerometer, gyroscope, and magnetometer; GPS08 input; four wheel-speed channels; lap time receiver input; and two digital outputs add up to a flexible, expandable data logger that can grow with you. It even has a screw-in port to add analog cameras used for back-up or rear view in visibility-challenged race cars! ALARMS & SHIFT LIGHTS Flexible alarms on the MXG 1.2 include six configurable RGB alarm LEDs: you choose the conditions, you choose the colors. Select a solid alarm or flashing one - and the flashing frequency, choose to have an accompanying text message, and set the alarm priorities. The integrated shift light array features a host of advanced multicoloured RGB shift light patterns that can be customized as you like, including RPM max for each individual gear. DIGITAL OUTPUTS The MXG 1.2 features two digital outputs (low-side type, switch to ground) that can be configured to activate/deactivate external systems (switch on/off additionallights, cooling fan relays, fluid circulation pumps, etc.) based on those inputs. MEMORY & WIFI CONNECTIVITY The 4GB non-volatile memory can store hours of information for detailed analysis using AiM's latest Race Studio 3 software.  A secure 802.11 WiFi connection makes it even more convenient to configure, calibrate, and download your data wirelessly!  No more need to move your PC close to the vehicle, you can do it from your trailer or tow vehicle up to 60 yards away. FEATURES & SPECS: 9.3" x 5.0" x 1.0" Anodized Aluminum housing Large 7.0" high-contrast color TFT display 800x480 pixel screen resolution Internal 4GB memory Two Motorsports and one Binder connector Weight 2.1 lbs (950g) Waterproof IP65 KIT INCLUDES: MXG 1.2 data logging dash GPS08 Module with cable USB cable wiring harness with 37 pin Deutsch connector installation CD with Race Studio 3 software All other sensors and modules sold separately.
AiM Sports MXP Midsize Color TFT Dash and Data Logger
AiM Sports AiM Sports MXP Midsize Color TFT Dash and Data Logger from $2,599.00
AiM MXP 50% Bigger Display Than MXS In Similar-Sized Package This brilliant dash logger from AiM features a stunning high-contrast color 6" TFT display, an integrated LED shift array, configurable multicolor LED alarms, drag and drop multi page configuration, Wi-Fi and USB connectivity, included GPS08 Module, inertial platform, analog and digital inputs, digital outputs, Motorsport connectors, 4 GB of internal memory, 1,000Hz per channel sampling and support for over 1,000 ECU connections! That all adds up to an incredibly flexible, powerful, and useable information center at your fingertips in your race car. WIDE RANGE OF DATA SOURCES The AiM MXP samples data coming from your ECU, the GPS Module, its internal nine-axis inertial platform (accelerometer, gyro and magnetometer), eight fully configurable analog inputs, six digital inputs, predefined math channels and a second CAN. Performance info and data acquired can be expanded by adding up to eight expansion modules. CONFIGURABLE PAGES You can define all the custom pages you wish, choosing from a wide library of page styles, defining which data to be shown, their end of scale and units of measure. Swapping between pages is as simple as pushing one or two buttons! FLEXIBLE ALARMS AND ICONS The MXP features five configurable RGB alarm LEDs: you choose the conditions, you choose the colors. Select a solid alarm or flashing one (and the flashing frequency), choose to have an accompanying text message, and set alarm priorities. You can also choose the street icons you need from a large list in Race Studio 3 - Icons Management, then set them up any way you prefer. They're all fully configurable, and if that's not enough, you can upload and set-up your own customized icons! TWIN DIGITAL OUTPUTS MXP features two digital outputs. They can be configured to respond to the analog or digital inputs to automatically run external systems (e.g. to switch on/off additional lights, activate/de-activate a cooling fan or fluid circulation pumps, etc.) DUAL CAMERA INPUTS Two analog camera inputs are available to swap your display into a mirror camera or rear-view camera through either push button command or in response to certain programmable events. Especially useful in a race car with limited visibility/sightlines. SHIFT LIGHT ARRAY Choose from a host of advanced multicolored RGB shift light patterns that can be customized as you like, including RPM settings for each individual gear. WiFi CONNECTIVITY It's so convenient to configure, calibrate, and download your data wirelessly using a secure 802.11 WiFi connection. No need to move your PC close to the vehicle anymore, you can do it  from your trailer or tow vehicle up to 60 yards away. KEY FEATURES & SPECS: Midsized 6" high-contrast color TFT display 800x480 pixel screen resolution 7.5" x 4.2" x 1.0" anodized aluminum housing Three CAN connections 15 configurable RGB LEDs Weight 1.4 lbs (640g) 4GB internal memory Waterproof IP65 KIT INCLUDES: AiM MXP dashlogger GPS08 Module with cable USB cable 37-pin Deutsch connector harness Installation CD with Race Studio 3 software
AiM Sports MXS 1.2 Compact Color TFT Dash And Data Logger
AiM Sports AiM Sports MXS 1.2 Compact Color TFT Dash And Data Logger from $2,599.00
AiM MXS 1.2 Color TFT 5" Dash And Data Logger Check Out The MX Series User Manual Here The MXS 1.2, the evolution of MXS, is a beautifully executed compact dash/data logger designed to put data at your fingertips. It can acquire data from your ECU, its internal accelerometer and gyro, the included GPS08 Module, analog/digital inputs and pre-defined math channels. The incredibly sharp, full-color TFT display puts it all front-and-center, in incredible color with a high contrast ratio. It even automatically adjusts its backlight based on ambient light to optimize visibility. Freely configurable pages let you define all the custom pages you wish, choosing from a wide library of page styles and defining which data to display, their end of scale and units of measure. Swapping between pages is as easy as pushing a button! GPS08 Thanks to the included GPS08 Module and AiM's Race Studio 3 software, you can immediately get lap times along with all data needed for engine tuning, shaking down car and driver, and for improving and refining driving technique. A MULTITUDE OF DISPLAYS The MXS 1.2 displays your RPM scale plus all the data you need (speed, water temp, oil pressure, lap times and much more) in pre-configured pages.  Or you can customize pages as you wish, choosing from a wide library of page styles and defining which data to be shown, their end of scale and measure units. Swapping between pages is quite easy using push buttons. A 4GB non-volatile memory stores hours of information for detailed analysis using AiM's Race Studio 3 software. All data can be downloaded to your computer using a built-in secure Wi-Fi connection (no cable required). LOTS OF INPUT/OUTPUT FLEXIBILITY Eight fully configurable analog input channels can sample, log, and display a wide range of temperatures, pressures, and potentiometers (throttle position, steering wheel position, etc). CAN Inputs allow you to further expand the dash by adding an almost limitless number of AiM CAN Data Hubs (Part No. MC-329, sold separately). These hubs let you connect other inputs such as Lambda Controller (O2), SmartyCam, or even channel expansion hubs, without using any analog channels. A separate CAN Output allows you to send messages to the existing CAN network, adding to the vehicle system control possibilities! The MXS 1.2 can also be connected to many different ECUs to log data gathered by each ECU. An internal three-axis accelerometer, gyroscope, and magnetometer; GPS08 input; four wheel-speed channels; lap time receiver input; and two digital outputs add up to a flexible, expandable data logger that can grow with you. It even has a screw-in port to add analog cameras used for back-up or rear view in visibility-challenged race cars! SHIFT LIGHTS & ALARMS Flexible alarms on the MXS 1.2 include six configurable RGB alarm LEDs: you choose the conditions, you choose the colors. Select a solid alarm or flashing one - and the flashing frequency, choose to have an accompanying text message, and set the alarm priorities. The integrated shift light array features a host of advanced multicoloured RGB shift light patterns that can be customized as you like, including RPM max for each individual gear. DIGITAL OUTPUTS The MXS 1.2 features two digital outputs (low-side type, switch to ground) that can be configured to activate/deactivate external systems (switch on/off additional lights, cooling fan relays, fluid circulation pumps, etc.) based on those inputs. WiFi CONNECTIVITY A secure 802.11 WiFi connection makes it even more convenient to configure, calibrate, and download your data wirelessly! No need to move your PC close to the vehicle anymore, you can do it from your trailer or tow vehicle up to 60 yards away. TECHNICAL SPECS: Compact 6.7" x 3.8" x 0.9" anodized aluminum housing 5" TFT high-contrast color display Internal 4GB memory Screen resolution 800x480 pixels Two Motorsport connectors and one Binder connector Weight 1.2 lb. (530g) Waterproof IP65 KIT INCLUDES: MXS 1.2 Unit GPS08 Module with cable USB cable 37-pin standard Deutsch-connector harness Software installation CD with Race Studio 3 software. All other sensors and modules sold separately.
High-performance AIM SmartyCam 3 GP video camera capturing racing action on the track.
AiM Sports Aim SmartyCam 3 GP $1,899.00
AiM Sports SmartyCam 3 GP The all-new SmartyCam 3 GP camera has been designed for motorsport with a single purpose: to provide great videos incorporating all the info and data you need. The AiM SmartyCam 3 GP camera overlays all the data from both GPS and AiM loggers connected to your ECU. It's a full HD camera system with video output, CAN connection, USB-C connection, and a GPS port as only a few of its features. AiM SmartyCam 3 GP: the power of simplicity. Perform Video Lap Analysis With AiM Analysis 3 With the AiM SmartyCam 3 GP and AiM Analysis 3 software, the video of a whole race, stint, or session can be downloaded on your PC and, with a simple click, can now be split into individual videos of each lap! This lets you simultaneously watch two laps side-by-side, seeing where you were faster or slower. The same operation can be performed with other drivers' SmartyCam 3 video recorded on the same track. You will be able to compare your best lap with theirs, giving you a powerful tool to refine racing lines, braking points, etc.! Automatic Race Track Selection The AiM SmartyCam 3 GP automatically recognizes the track you're racing on, easily drawing it out and calculating lap number, lap times and rolling times. Automatic Data and Video Synchronization Simply import the video file and racing data from your AiM logger and AiM's amazing software will automatically synchronize your position on the track, video frame, and race data on the graphical display. Your video and the most important data are saved simultaneously in the same mp4 file. AiM SmartyCam 3 GP Details: Video format: H.264 compression; 1920x1080 pixels @ 60 FPS Display resolution: 2.4-inch, 240 x 320 pixels Lens: Low distortion camera lens CMOS sensor: Global Shutter Field-of-view: 67°, 84°, or 120° Internal battery: Rechargeable lithium battery Video Out: 3G-SDI External power: 9V to 15V Supports SD card: up to 2 TB (SD card not included) Connectors: two Binder 712 female connectors; two SMA female connector; one USB-C Usage temperatures: -10°C to 50°C (14ºF to 122ºF) Auto Power ON: Yes Auto Power OFF: Yes Auto Start/Stop recording: Yes Body construction: anodized aluminum Dimensions (main unit): 120.8 x 80.2 x 30.9 mm (4.75 x 3.25 x 1.25 in) Dimensions (bullet camera): ø 24mm x 41mm (67° & 84° lens); ø 24mm x 46mm (120° lens) Bullet cable length: seven different lengths available from 0.5m to 4m (1.6 ft to 13.1 ft) Weight: main unit, 320g (11 oz); bullet camera 45g (1.6 oz) Waterproof: IP65
AiM Sports MXG 1.3 Strada Large Color TFT Dash
AiM Sports AiM Sports MXG 1.3 Strada Large Color TFT Dash $1,599.00
AiM MXG 1.3 Strada Color TFT Dash The Full-Size Color TFT Dash For Road Use MXG 1.3 Strada ("street" in Italian) is a beautifully-designed, feature-rich color digital dash display. It is basically the MXG 1.3 without the datalogging function. The MXG 1.3 Strada features a wide 7" High Contrast TFT color screen with great visual impact, configurable to show lap times, RPM, and a huge range of info coming from your Engine Control Unit, analog/digital inputs, pre-defined math channels and an optional GPS08 Module. Programmable multicolor shift and alarm LEDs round out an incredibly powerful package. The MXG 1.3 Strada displays your RPM, selected gear, speed, plus all the data you choose (water temp, oil pressure, trans temp, lap times and much more) in either pre-configured or user-customized pages. Swapping between pages is as easy as pushing buttons. Plus the MXG 1.3 Strada puts a huge amount of control over your car's systems at your fingertips. There's even a version with "Street Icon" LEDs instead of the traditional "plain" LEDs! INPUT & OUTPUT FLEXIBILITY Eight fully configurable analog input channels can sample, log, and display a wide range of temperatures, pressures, and potentiometers (throttle position, steering wheel position, etc). Available only in a CAN/RS232 version for the maximum level of customization and data access. The CAN input allows you to further expand the dash by adding an almost limitless number of AiM CAN Data Hubs (Part No. MC-329, sold separately). These hubs let you connect other inputs such as Lambda Controller (O2), SmartyCam, or even channel expansion hubs, without using any analog channels. A separate CAN output allows you to send messages to your car's existing CAN network, adding to the vehicle system control possibilities! ALARMS & SHIFT LIGHTS The ten multicolored RGB shift lights can be customized to define the max RPM  for each single gear.  The same flexibility applies to the configurable RGB alarm LEDs: you can configure them to turn on/off depending on analog or digital inputs, ECU values, expansion values, math channels or GPS information (with the optional GPS08). You choose conditions, colors, and select a solid alarm or flashing one (including flash frequency). It's also possible to configure an accompanying text message. DIGITAL OUTPUT The MXG 1.3 Strada features a low-side (switch to ground) digital output that can be configured to activate/deactivate external systems (switch on/off additionallights, cooling fan relays, fluid circulation pumps, etc.) based on those inputs. RACE STUDIO 3 MXG 1.3 Strada is configured using your PC and Race Studio 3. You can create, customize, delete, import and export configurations with all channels, ECU drivers, Math Channels, Display Pages, Digital Output, Alarms, Shift Lights and all the expansions you need. AiM MXG 1.3 STRADA TECHNICAL SPECS: 9.3" x 5.0" x 1.0" anodized aluminum housing Large 7.0" high-contrast color TFT display 800x480 pixel screen resolution Weight: 2.1 lbs (950g) Waterproof: IP65 KIT INCLUDES: MXG 1.3 Strada digital dash USB cable 14-pin standard wiring 23-pin connector + contacts Installation CD with Race Studio 3 software All sensors and modules sold separately.
Aim SmartyCam 3 Corsa capturing high-speed racing action.
AiM Sports AiM SmartyCam 3 Corsa $1,399.00
AiM Sports SmartyCam 3 Corsa Introducing the upgraded SmartyCam 3 Corsa, the newest iteration of the AiM SmartyCam HD. This enhanced version takes the well-known design to new heights, featuring an improved Global Shutter and the ability to capture video at up to 60 frames per second. Unlike conventional action cameras that cater to various extreme activities like skydiving or riding monstrous waves, the SmartyCam HD is meticulously crafted by dedicated motorsports enthusiasts who live and breathe the racetrack. Its narrow angle lens is specifically tailored for seamless mounting in sedans and sports cars, neatly fitting within the A-pillars for optimal placement. The new SmartyCam 3 Corsa camera has been designed for motorsport with a single purpose. Get The Best Motorsports Videos With Amazing Data Overlays The AiM SmartyCam 3 Corsa camera overlays all the data from both GPS and AiM loggers connected to your ECU. The Motorsports  Camera With A Full Data Logger Built In All data received by the AiM SmartyCam 3 Corsa from both the CAN bus and its own internal sensors are recorded in mp4 files produced at the end of your stint or session. Your SD (or Micro SD) card contains all the information you need for a deep data analysis. (SD and Micro SD cards sold separately.) The video of a whole session, once downloaded on your PC, can now be split with a simple click into individual videos of each lap. So now you can simultaneously watch two side-by-side to see where you were faster or slower. The same operation can be performed with a SmartyCam 3 Sport video recorded on the same track. You'll be able to compare your best lap with other drivers, other set-ups, and so on! The Only HD Camera Built for the Punishment of Motorsports An on-board or in-car camera designed for motorsport must guarantee great resilience and reliability in the extreme working conditions typical of racing, and against the most adverse weather. That's why the AiM SmartyCam 3 Corsa is IP65 waterproof. Constructed from machinery-molded aluminum, PA fiberglass reinforced and featuring a sapphire frontal lens glass, the SmartyCam 3 Corsa is built like a tank. The Convenience and Ease of Auto Stop and Start You have other things to think about while you're at the race track, and the AiM SmartyCam 3 Corsa is designed with that in mind. That's why it switches on and off automatically, as well as starting and stopping recording in the same way. No Video Wave Effect with the Motorsports CMOS Global Shutter At speed on the race track, chassis vibration, engine rumble, and wind buffeting cause vibrations that are a big problem for generic sports video cameras. The AiM SmartyCam 3 Corsa is designed and built specifically to handle that environment, so you'll never experience that seasick “wave effect” you get in videos recorded by generic cameras. Ultra High-Quality Vide with Small File Sizes Generic HD cameras are absorbed with having the highest pixel count. The result is that their video files are huge, eating up memory and processing power. AiM SmartyCam 3 Corsa videos, on the other hand, have the same high video quality as other HD cameras, but their files are smaller because the H.264 compression system parameters have been optimized to perfectly balance video quality and file size. AiM SmartyCam 3 Corsa Details: Video format: H.264 compression; 1,920x1,080 pixels @ 60 fps Display resolution: 128x128 px Lens: low distortion, sapphire front glass CMOS sensor: global shutter Field-of-view: 67º or 84º Internal battery: rechargeable lithium External power: 9V to 15V Supported Micro-SD card: up to 2 TB (not included) Connectors: three Binder 712 female connectors; one USB-C Operating temperatures: -10°C to 50°C (14ºF to 122ºF) Auto power on: yes Auto power off: yes Auto start/stop: yes Camera body: coated aluminum Dimensions: 102.2 x 63 x 46.5 mm (4 x 2.5 x 1.8 in) Weight (w/ battery): 280 g (0.62 lb) Waterproof: IP65
AiM Sports MXP 1.3 Strada Large Color TFT Dash
AiM Sports AiM Sports MXP 1.3 Strada Large Color TFT Dash from $1,299.00
The Full-Size Color TFT Dash For Road Use The AiM Sports MXP Strada is a 6" colour display with great visual impact, configurable to show lap times and all the info coming from the Engine Control Unit, analog/digital inputs, pre-defined math channels and - optionally - the GPS09 Module. Integrated shift light array Choose from a host of advanced multicoloured RGB shift light patterns that can be customized as you like, and for each unique gear when required. INPUT & OUTPUT FLEXIBILITY AiM systems acquire data from the ECU of your vehicle.The list of available ECU drivers, constantly updated and upgraded, includes 1,000 + different ECUs, either Stock and Racing; they are sorted by manufacturer/vehicle model: for each ECU you find the proprietary communication protocols, including the standard OBDII ones. From a hardware point of view, AiM systems manage the following data lines: CAN, RS232 and K-Line. Analog/digital inputsAiM systems analog inputs are recorded up to 1,000 times per second each. You can connect and monitor all kinds of sensors, like: Ratiometric potentiometers Pressure sensors Thermo-resistances K-type thermocouples ... and many others, all your custom sensors included. Freely configurable pages You can define all the custom pages you wish, choosing among a wide library of page styles, defining which data to be shown, their end of scale and measure units. Swapping between pages can be managed pushing one or two pushbuttons. High contrast TFT display A high contrast TFT display identifies MXP Strada at the first glance. An ambient light sensor keeps the backlight at optimum brightness levels. Flexible alarms & custom street icons MXP Strada, in its standard version, features five configurable RGB alarm LEDs: you choose the conditions, you choose the colors. Select a solid alarm or flashing one - and the flashing frequency, choose to have an accompanying text message, and set the alarm priorities. Furthermore you can select the street icons you need among the wide list you will find in "Race Studio 3 - Icons Management" and set them up the way you prefer or according with your needs. Any of them is fully configurable and if this shouldn't be enough, you will be able to upload and set up your own customized icons. AiM systems also feature digital inputs: Speed signals From the ECU, from the GPS and from the wheel sensors. RPM From the ECU or from a digital input connected to a square wave signal (8 to 50 V) or to a low voltage (from 150 to 400 V) of the coil. Lap signal Lap and split times are sampled by the GPS or via optical receiver/transmitter. Camera inputs, also for mirror camera Two analog camera inputs are available, to swap your display into a mirror camera,through pushbutton command or event management. Digital output MXP Strada features a LOW SIDE type (switch to ground) digital output configurable in order to be activated/deactivated depending on the value of the analog/digital inputs or on impulses coming from the ECU. This permits to automatically run externalsystems, i.e. to switch on/off additional lights, to activate/de-activate a cooling fan or circulation pumps, etc. when a certainevent happens. RACE STUDIO 3 MXP 1.3 Strada is configured using your PC and Race Studio 3. You can create, customize, delete, import and export configurations with all channels, ECU drivers, Math Channels, Display Pages, Digital Output, Alarms, Shift Lights and all the expansions you need. TECHNICAL SPECS: 9.3" x 5.0" x 1.0" Anodized Aluminum housing Large 7.0" high-contrast color TFT display 800x480 pixel screen resolution Weight 2.1 lbs (950g) Waterproof IP65 KIT INCLUDES: MXP 1.3 Strada digital dash USB cable 14-pin standard wiring 23-pin connector + contacts Installation CD with Race Studio 3 software All sensors and modules sold separately.  
AiM Sports MXm Compact Dash Logger
AiM Sports AiM Sports MXm Compact Dash Logger from $1,299.00
AiM Sports MXm Compact Dash Logger The new MXm from AiM is the compact dash logger with big features to put all the information you need right at your fingertips. It samples and shows key info like speed, lap times, RPM, gears, data from a nine-axis inertial platform, multiple math channels and much more. It is compact (5.4 x 3.5 x 1.3 in.), making it perfect for sports cars and bikes, and it's plug-and-play for ease-of-use. Complete but simple, MXm is the perfect device for both Pro and Amateur drivers. WIDE RANGE OF DATA SOURCES MXm samples data from your ECU, its internal GPS and inertial platform (accelerometer, gyro and magnetometer), four fully configurable analog inputs, three digital inputs (two speed + one coil RPM input), and predefined math channels. For the most demanding, the MXm can be connected to the Lambda controller and a SmartyCam HD to create a fully-integrated AiM information suite. INTEGRATED SHIFT LIGHTS & ALARM MXm features a five-LED shift light array. Choose from a host of advanced multicolored RGB shift light patterns that can be customized to your needs, and for each unique gear when required. MXm also features two fully configurable RGB alarm LEDs: you can choose the conditions that turn them on/off, their color, and select a solid alarm or flashing one (and the flash frequency.) DUAL POWER OUTLETS MXm features two power outputs that can supply up to 15A each. These outputs can turn on/off depending on the value of analog or digital inputs to the MXm. They can automatically actuate external systems, such as switching on/off additional lights, activating/de-activating cooling fans or circulation pumps, etc. SHARP LCD MXm features a high contrast LCD display with an outstanding black to white ratio. The wide 268 x 128-pixel graphical LCD offers great flexibility in information display and alerts. The screen can be backlighted in one of the seven available colors, and an ambient light sensor keeps the backlight at optimum brightness. CUSTOMIZABLE LAYOUT You can organize the huge quantity of data captured by MXm into your own custom pages, choosing from a wide range of page styles, data to be shown, their end of scale and unit of measure. At the end of each session, you can review an on-screen summary of your best laps, max/min RPM, speed and temperatures. WIFI CONNECTIVITY Makes it even more convenient to configure, calibrate, and download your data wirelessly, using a secure 802.11 connection. No need to move your PC close to the vehicle anymore, you can do it from your trailer up to 50 yards away. SMARTYCAM COMPATIBILITY SmartyCam on-board cameras, for professional recording of your races, with your real-time data overlayed on videos. RACE STUDIO 3 DATA ANALYSIS Race Studio 3 is the true engine of your MXm. With Race Studio 3, you can analyze all data recorded by MXm and downloaded to your PC. RS3 generates graphs, histograms, and tables to help you study your performance, providing an objective support to correct mistakes and improve your driving. You can even compare two laps watching the video recorded by SmartyCam HD cameras! RS3 can create, modify, delete, import and export MXm configurations with all channels, ECU drivers, math channels, display pages, digital outputs, alarms, shift lights and expansions.
AiM Sports MXS 1.3 Strada Compact Color TFT Dash
AiM Sports AiM Sports MXS 1.3 Strada Compact Color TFT Dash $1,299.00
The Compact Color TFT Dash For Road Use WIDE RANGE OF DATA & DISPLAYS MXS 1.3 Strada is a beautifully-designed, feature-rich color digital dash display. It is basically the MXS 1.3 without the datalogging function. The MXS 1.3 Strada features a compact 5" High Contrast TFT color screen with great visual impact, configurable to show lap times, RPM, and a huge range of info coming from your Engine Control Unit, analog/digital inputs, pre-defined math channels and an optional GPS08 Module. Programmable multicolor shift and alarm LEDs round out an incredibly powerful package. There's even a version with "Street Icon" LEDs instead of the traditional "plain" LEDs! The MXS 1.3 Strada displays your RPM, selected gear, speed, plus all the data you choose (water temp, oil pressure, trans temp, lap times and much more) in either pre-configured or user-customized pages. Swapping between pages is as easy as pushing buttons. Plus the MXS 1.3 Strada puts a huge amount of control over your car's systems at your fingertips. INPUT & OUTPUT FLEXIBILITY Eight fully configurable analog input channels can sample, log, and display a wide range of temperatures, pressures, and potentiometers (throttle position, steering wheel position, etc). Choose between OBDII and CAN/RS232 versions to suit your needs and level of customization. Both receive rich data from your ECU. An OBDII input connection is an easy, plug-and-play option. A hardwired CAN input allows you to further expand the dash by adding an almost limitless number of AiM CAN Data Hubs (Part No. MC-329, sold separately). These hubs let you connect other inputs such as Lambda Controller (O2), SmartyCam, or even channel expansion hubs, without using any analog channels. A separate CAN output allows you to send messages to your car's existing CAN network, adding to the vehicle system control possibilities!   ALARMS & SHIFT LIGHTS The ten multicolored RGB shift lights can be customized to define the max RPM  for each single gear.  The same flexibility applies to the configurable RGB alarm LEDs: you can configure them to turn on/off depending on analog or digital inputs, ECU values, expansion values, math channels or GPS information (with the optional GPS08). You choose conditions, colors, and select a solid alarm or flashing one (including flash frequency). It's also possible to configure an accompanying text message.   DIGITAL OUTPUT The MXS 1.3 Strada features a low-side (switch to ground) digital output that can be configured to activate/deactivate external systems (switch on/off additional lights, cooling fan relays, fluid circulation pumps, etc.) based on those inputs.   RACE STUDIO 3 INTEGRATION MXS 1.3 Strada is configured using your PC and Race Studio 3. You can create, customize, delete, import and export configurations with all channels, ECU drivers, Math Channels, Display Pages, Digital Output, Alarms, Shift Lights and all the expansions you need. TECHNICAL SPECS: Compact 6.7" x 3.8" x 0.9" anodized aluminum housing 5" TFT high-contrast color display Choose Standard or Street Icon LEDs Screen resolution 800x480 pixels Weight 1 lb. (480g) Waterproof IP65 KIT INCLUDES: MXS 1.3 Strada digital dash USB cable 14-pin standard wiring 23-pin Connector + contacts Installation CD with Race Studio 3 software All sensors and modules sold separately.
AiM Sports Strada Logger GPS Upgrade Kit
AiM Sports AiM Sports Strada Logger GPS Upgrade Kit $1,165.00
Strada Logger, GPS08 Module, And Data Hub Turn Any MX Strada Into a Full Data Logger Receiving and reading data while you are driving is not enough anymore? Then it's time to step your game up with the brand new Strada Logger Kit!  This kit includes the Strada Logger, Data Hub and GPS08 Module, the kit will turn any MX Strada into a full-working logger, able to collect data ready to be analized on Race Studio 3 to make you improve your performance, understand whether there are problems or not within your vehicle and much much more. STRADA LOGGER A small SD Card holder that can be connected via CAN bus to your MXG 1.2 Strada, MXP Strada, or MXS 1.2 Strada. (It can also be connected to your MXG 1.2, MXP, or MXS data logger for data back-up and super-fast downloads.) GPS08 MODULE More precise than most of the existing GPS systems, the GPS08 was designed to add to the GPS satellite's signal the Global Navigation Satellite (Glonass) system's signal. With an average of almost twenty satellites working in conjunction, GPS08 guarantees precision and a reliability simply not comparable to other GPS systems. DATA HUB A CAN connection multiplier that works as an interface between all AiM loggers and their peripheral equipments. Just connect the Strada Kit to your AiM MX device and data will be saved on an SD card (not included) up to 32GB. as well as stored in the logger memory. No configuration is needed. The SD card can be removed and replaced even during pit stops, while the car engine is still ON, making it extremely fast to get data during endurance races or long tests when the time in the paddock is really limited. When your session is over, plug your SD Card into your PC and download data into Race Studio 3. The Strada Logger has a front LED that shows its recording/firmware status. Reliable and easy to install, the Strada Kit is just what you need to go from an above average driver to a real race one!
Garmin Catalyst Driving Performance Optimizer: A sleek device on a dashboard, displaying real-time data.
Garmin Garmin Catalyst™ Driving Performance Optimizer $999.99
Garmin Catalyst Driving Performance Optimizer Realize Your Full Track Driving Potential This device is an industry-first, providing virtual coaching in real time and showing a calculated optimal lap. Real-time coaching tells you how to go faster in each corner, with audio instructions, so you can keep your eyes up at all times. This is a stark contrast to existing systems which only provide feedback after a corner or after your session. The Garmin Catalyst uses your measured optimal lap to guide you to your personal maximum performance, rather than the performance of a professional racing driver. Catalyst Overview Garmin Catalyst uses accelerometers, GPS, video, and the most sophisticated algorithms to evaluate your driving performance and then suggest ways to improve (just like a human coach). Through the display and audio, Catalyst provides a real-time assessment of performance using both gentle suggestions and positive reinforcement. No, it won't clap when you get it right but it does use real-world phrases and encouragement - such as "brake less", "apex later", or "keep pushing". Catalyst is perpetually evaluating and assessing your performance so it can optimize your lap and get you in line. After your session, review track maps showing opportunities for improvement as well as "heat map" displays of deceleration, acceleration, apexes, and speeds. Catalyst uses a 6.95" super wide view LCD IPS screen with vivid TFT colors. The LCD is a touchscreen, able to control functions without the need for a remote control, app, or a laptop. Coaching or playback audio is available via 3.5mm headphone jack or Bluetooth(TM) to your headset or car stereo. The on-screen layout is not programmable. More Than Just Another Camera This is more than just a camera - the remote pod includes the accelerometers. It records up to 30fps in 1080p HD in a 140° field-of-view. It must be mounted facing forward, high up, and centered on your windshield. An on-screen guide will help you align it. The camera contains the accelerometers and very powerful processing software integrates the video into Catalyst's coaching and data. Playback is available on the Catalyst screen with speed and lap times already in sync. On-Track Coaching To unlock all of the coaching features and data you will need to select the Advanced setting. There is also a Basic setting that does not provide as much feedback. During your session, the real-time display is referencing current session data only. However, post-session review can include data from multiple sessions. Catalyst is looking for patterns in your driving to map out where you were fast and opportunities to try a different line, brake less, or carry more speed. Lap time differential is displayed as either red (slower), green (faster), or black (no change). You can have an advanced driver or instructor set baselines in your car first, then overlay that data with your own driving. This way Catalyst can see the full potential and make recommendations. So, instead of "chasing" a theoretical lap time, you know what's possible with Catalyst helping you make incremental improvements to get there. Catalyst will never make a recommendation that hasn't been previously successful. Off-Track Analysis & Review Garmin Catalyst compiles all of its data to form a True Optimal Lap. This is your best possible lap using all of the data provided during your on-track sessions. True Optimal Lap is determined not just by lap and sector times but by analyzing your best lines through corners and sectors and using the camera feed to identify track limits. Catalyst retains your track data over a four-day period so you can pack in a full weekend of driving with progressive coaching and analysis. Post-session data is reviewed on the Catalyst screen or through the Garmin Connect smartphone app, including video. (Export of data and video files to a laptop is not currently supported nor is it needed.) Everything you need is self-contained in the Garmin Catalyst, which works best when used as a standalone tool to review performance and make adjustments while you're at the track. Included in the Catalyst Box: Garmin Catalyst 32GB microSD pre-installed in covered compartment (auxiliary card slot on the side of the Catalyst device is externally accessible for memory expansion) Remote Cam with polarized lens cover Remote Cam 3.5 meter cable Heavy-duty vehicle suction cup Powered magnetic mount Two 1” connecting arms 1” arm connector Cable clips 12V socket power cable Full documentation Included Accessories: One-inch ball adapter screw down mount USB data cable 12V bare wire vehicle power cable Additional Remote Cam adhesive Continue reading to see how and why the Garmin Catalyst Driving Performance Optimizer is unlike anything you've ever experienced. Heck... it's unlike anything you've ever even thought possible!
AiM Sports SmartyCam 3 Sport Data Logger Camera
AiM Sports AiM Sports SmartyCam 3 Sport Data Logger Camera $899.00
AiM Sports SmartyCam 3 Sport The new AiM SmartyCam 3 Sport takes AiM your motorsports video to the next level. Specs include a resolution of 1920x1080 FHD with 60 frames per second (fps) utilizing H.264 (MPEG-4 Advanced Video Coding), bringing you the best video quality of any AiM camera ever. This is not a plastic "action-sports" camera, it's a real motorsports camera built to live up to the rigors that a race car demands. The AiM SmartyCam 3 Sport is the latest generation of the best motorsports cameras. If you have an AiM dash and want to add great videos that include all the technical information that will help you improve your performance, the AiM SmartyCam 3 Sport is your answer. Get the Shot Every Time with Automatic On/Off AiM SmartyCam 3 Sport can be switched on/off automatically by the logger it is connected to. Simply decide what period of non-activity triggers the camera to switch-off. Both operations can also be carried out using the keyboard if you prefer. Recording can also be started/stopped automatically or via keyboard: the camera will start recording when a set speed or RPM threshold is exceeded. You simply decide how long after dropping below the selected threshold the video will automatically stop. No More Distorted "Wave Effect" Race Track Videos Engine rumble causes vibrations, which are not good for video recording. With the AiM SmartyCam 3 Sport, you'll never again experience that seasick "wave effect" you see when watching in-race videos recorded by generic cameras in a car screaming at 7000 RPM. The AiM SmartyCam 3 Sport is designed for that environment and for those vibrations. "Wave effect" is now just a memory. Generic action cameras are designed to record videos in many different situations, such as skiing or surfing. But in motorsports they tend to record misleading videos, straightening out the view ahead. When on track, this distorted view makes the corners seem to disappear. So, when you review your track performance those videos are useless because the images are distorted. Lenses Designed WIth Motorsports In Mind Being a camera dedicated to motorsports, AiM SmartyCam 3 Sport features lenses specifically designed to eliminate distortion. The camera is available in two versions: 67º and 84º field-of-view. The former is most suited to in-car, closed-cockpit use. The latter is best used mounted to the exterior of either open- or closed-cockpit cars. Real Time Data Overlay With no driver input, the AiM SmartyCam 3 Sport will automatically overlay all the data you need onto your videos: speed, RPM, lap number, gear shifts and much more. Simply choose the data and the graphic layout you prefer from the huge selection of overlays available. What Kind of Data? AiM SmartyCam 3 Sport overlays data from different sources onto your videos. All this info can be overlayed on videos at each single point of the track. From a GPS: track map and vehicle position, speed, lap- and split-times. From an Aim logger connected to your ECU: RPM, throttle, engaged gear, acceleration, temperatures, pressures, and additional sensor values (if available). AiM RaceStudio 3 Software With RaceStudio 3, the AiM SmartyCam 3 Sport dedicated software, you can add your logo and track map to your videos. There's also a wide choice of graphical objects available, allowing you to choose from a list of pre-determined sets with the same layout, or to combine single objects from different sets.  Now your videos will be truly “yours” in all details, from data to their graphic design. To use the AiM SmartyCam 3 Sport with direct 12v power you will need the Manufacturer Part Number: X08HB2GK0AiM SmartyCam 3 Sport Video Camera Details: Manufacturer: AiM Manufacturer part number, 67° FOV: XS3S674U Manufacturer part number, 84° FOV: XS3S844U Included cable length: 4M (13 feet) Connector to dash harness or data hub: SmartyCam 712 female Audio: Internal microphone
AiM Sports Solo 2 DL Data Logging Lap Timer
AiM Sports AiM Sports Solo 2 DL Data Logging Lap Timer $799.00
AiM Sports Solo 2 DL Data Logging Lap Timer THE BRAND NEW DATA-LOGGING GPS LAP TIMER FOR MOTORSPORTS The new Solo 2 DL receives data from two satellite constellations, GPS and Glonass; this is a huge step forward since it is unbelievably faster and more precise than the previous version. Power-on requires only a few seconds and lap times are calculated with a max 2/100 sec. of tolerance thanks to 10Hz GPS sampling. A sleek newly-designed case with easier-to-use metal buttons add a premium look and feel to the world's most popular data-logger and GPS lap timer. The screen can be back-lighted in one of the seven colors: ECU CONNECTION Solo 2 DL -- the Solo with an ECU connection -- has over a thousand ECU protocols in its database. Easily connect your Solo 2 DL to your ECU and get reams information with just one cable. In case your ECU protocol isn't in the database, no problem: an ECU Driver Builder is available in the included Race Studio 3 software, allowing you to create your protocol yourself. This gives you access to a huge amount of data from your car that can be overlaid with GPS data to create an incredibly powerful analysis and learning tool! Choose your ECU cable: OBD2: the standard vehicle diagnostic port beneath your dash supplies the Solo 2 DL with a wealth of information. This is the standard cable most people will use. CAN/RS232: the Solo 2 DL can be connected to your CAN Bus for an even richer, broader spectrum of information than OBD2. This cable can require a bit more know-how to connect, however. Coil RPM: the Solo 2 DL now features a digital input allowing to log RPM either from square wave signals (8-50 V each signal) or pulse signals (150-450 V ignition coil trigger – primary circuit).  FIND YOUR TRACK QUICKLY Solo 2 DL has access to a database of more than 3,000 tracks all over the world! As soon as it switches on, the Solo 2 DL identifies its position, recognizes the starting line coordinates of the track, and is ready to start sampling lap times. If your track isn't in the database, no problem: the Solo 2 DL will automatically enter into autolearning mode, figures out the characteristics of the track, and starts lap-timing anyway. PREDICTIVE LAP TIME LEDS The new Solo 2 DL's predictive lap time engine is now even more reliable. And with configurable RGB LEDs, it will give you a clear, fast indication of how your current lap compares with your best possible lap. That's functionality you typically find only on expensive driver-coaching electronic aids; now it's at your fingertips with the Solo 2 DL! RACE MODE SELECTION Solo 2 DL can manage different types of races: Speed races in a closed circuit Point to-point races Regularity Performance tests (0-100 km/h etc.) In each of these configurations, Solo 2 DL gives the relevant information during the race/test along with powerful data review immediately after each session. WiFi & iPHONE CONNECTION WiFi communication with your laptop is easy, fast, and with no connectors or cables. It's the best way to configure your Solo 2 DL, manage the track database, and download lap data to your PC. Connect your Solo 2 DL to your iPhone for quick and easy data analysis, managing your track database, etc. SMARTYCAM INTEGRATION The perfect connection: the Solo 2 DL takes all the data from your ECU, merges it with GPS lap information, and transmits everything seamlessly to a SmartyCam HD or SmartyCam GP HD . The resulting video includes your ECU and lap data in a graphical overlay! Feel free to give us a call at (844) 438-7244 to discuss the cool new features and capabilities of AiM's latest, greatest compact datalogger/lap timer today!
Sold out
Apex Pro Gen II Lap Time Optimizer
Apex Pro Apex Pro Gen II Lap Time Optimizer $589.00
APEX Pro Gen II Lap Time Optimizer APEX Pro is a tool for competitive drivers. From track days and road racing to autocross and hill-climb, APEX Pro is a tool that helps improve lap times while on track and simplifies post-session data review with the most intuitive software interface available. APEX Pro pairs using Bluetooth with your Apple (iOS smartphone) to automatically save data to the APEX app. It provides accurate lap-times at over 200 official tracks around the world, as well as allowing custom track creation. While on track, precisely filtered data is logged at 10 Hz and sent to the smartphone. APEX has a suite of tools allowing drivers to review and replay data overlaid on track maps or plotted in many other ways. To compare laps with other drivers, simply email or AirDrop recorded sessions to fellow drivers or driving instructors. You can instantly overlay and compare sessions from the same track. While you're out on the track, friends and crew members can watch your driving and lap-times (and telemetry with Gen II) from anywhere in the world using the CrewView social platform (iOS). THE ULTIMATE DRIVING COACH Red lights on the APEX Pro indicate unused potential. In motorsport terms, the tires are not at their limit. This limit is calculated by taking in thousands of sensor measurements per second from the internal GPS and accelerometers (nine-axis IMU). These raw sensor measurements are then filtered through the APEX algorithm derived from years of testing at all levels of motorsport. This process on takes a lap or two of driving at pace, and from these measurements APEX determines the car’s road-holding ability (based on your driving, not a theoretical limit). That's how APEX helps you find your limit. Peak measurements are compared with the other measurements to determine if those peaks seen in one area of the track are achievable elsewhere. Put another way, you may be faster in one section of the track than another, and that is how APEX learns where the available grip is. Red lights represent the limit determined by the APEX algorithm, green lights show you how close you are to that limit. For more information, check out the APEX Pro startup guide linked below! NEW GEN II FEATURES Smoother, more precise data (satellite map and data graphs). Easier interpretation of APEX Coaching model (100% APEX score is possible!) Predictive timing display option on the APEX LEDs. Battery indicator light on the unit (green = fully charged). Lower profile design. Increased battery life (6+ hours) USB-C charging cable New APEX App User Interface for easier use Charging indicators: red LED, unit charging; green LED, unit done charging. Telemetry: live streaming of ground speed, longitudinal and lateral G data traces DRIVER BENEFITS Easy-to-interpret real time display (no more red lights on the straights if you get a good exit) Lower profile means it takes up less space on the dash so your vision is not obstructed. You now know if your APEX Pro unit is being charged when you plug it in, and whether it’s fully charged. Predictive LEDs make it super-simple to see if you are trending faster or slower than your best lap so far. Telemetry is perfect for track side instruction and endurance racing. THE ADVANTAGES OF APEX PRO Sixty-day, no-questions-asked money back guarantee. View return policy here. All APEX units have a 12-month hardware warranty. Send the unit back to APEX within one year of purchase for a free repair if you experience issues. Extend your warranty buy purchasing an annual Lap Timer Plus membership. Your warranty is extended for as long as you subscribe. Download the free APEX app. Your purchase comes with a free 30-day trial of Lap Timer Plus membership. Lap Timer Plus includes discounts on APEX Pro products, online courses, and webinars in addition to unlocking additional features in the app. Visit the APEX Pro FAQ  section to learn more about APEX Pro. Also, view the APEX Pro Mounting Guide. Do you autocross? Check out the Custom Track Feature Guide. The APEX Pro YouTube page features hours of helpful data review content. Subscribe to get notified when new videos are posted. APEX Pro is more than a product, it's a community of users. Click here to join the APEX Pro user group on Facebook.