Arai

Arai CK-6 Youth Karting Helmet The Arai CK-6 is designed specifically for junior kart racers who are too small to comfortably fit and/or support the weight of an Arai SK-6 adult karting helmet. Meets the Snell/FIA CMR-2016 standard for junior karting. Arai CK-6 Youth Karting Helmet Details SRC Superior Resin shell material, developed and formulated in-house at Arai, dramatically improves the bonding properties of standard fibers, allowing the use of less material for reduced weight and lower cost. Removable/replaceable cheek pads in optional sizes allow for custom fit when needed. Easily removable 5mm top layer of foam allows for further custom fitting. Wide and tall eye port for an exceptional field of view. Large intake vent toggles for easy operation, with large rear vents for improved ventilation. Features taken directly from the GP-6PED auto-racing helmet. Newly sculpted chin bar and ridge along lower edge of shell to improve structural integrity. Provides a stronger shell near the opening where it's needed while lowering the center of gravity. Rise in shell above the shoulders for added clearance. Sizing Specific To Young Kart Racers XXS: 50-51cm XS: 52-53cm S: 54-56cm M: 57-58cm L: 59cm An effective helmet is one that fits properly. Have an assistant use a measuring tape, or a piece of string to measure the circumference of your head starting at a point approximately one inch above the eyebrows in front, around a point in the back of the head that results in the largest possible measurement, and finally wrapping back to the front. It is a good idea to take several measurements to make sure you have the largest one.

Arai Auto Racing GP-5W SA2020 Helmet The Arai Auto Racing GP-5W SA2020 Helmet is perfect for stock car, sedan, and rally drivers. The GP-5W Helmet is a favorite because of its wider, 90mm (approx 3.5” top to bottom) eye port opening. The GP-5W uses its own exclusive shield with this larger opening. The ARAI GP-5W is Snell SA2020 certified with M6 washer/nuts installed at the factory. Drivers of any experience level will be able to easily install their Head and Neck Restraint system anchor posts (sold separately). The Arai Auto Racing GP-5W SA2020 also comes with the FIA-8859-2015 certification sticker found on the shell’s interior lining. ARAI GP-5W AUTO RACING HELMET SCLC CONSTRUCTION The ARAI GP-5W Helmet SA2020 is built with Arai's exclusive, very-lightweight SCLC (Super Complex Laminate Construction) shell technology. This ensures a low overall weight to balance the added weight of the helmet’s larger shield. ARAI GP-5W AUTO RACING HELMET SHELL SHAPE The Arai Auto Racing GP-5W Helmet SA2020 helps reduce fatigue for the driver due to its more natural head shape, smaller shell size, and lower center of gravity to assist with balance and stability. INTERIOR FIT OF THE ARAI GP-5W The Arai Auto Racing GP-5W Helmet SA2020 is designed to closely match the shape of the human head, allowing for a snug, yet comfortable, fit. Arai has developed this “natural” shape over more than 50 years of helmet design research and refinement. WIDER EYE PORT OF THE ARAI GP-5W Sedan drivers will appreciate the larger, 90mm eye port, top to bottom. A visor peak is available for drivers not needing a shield on the The Arai Auto Racing GP-5W Helmet SA2020. ARAI GP-5W REMOVABLE/REPLACEABLE CHEEK PADS Low maintenance, easy-to-clean cheek pads are removable, washable, and replaceable with pads of varying thickness to provide a snug, safe fit. M6 ANCHORS The FIA-8859-2015 certified GP-5W helmet has M6 threaded washer/nuts with 6mm threads pre-installed. This convenient feature lets the driver use the anchor system that works best with their Head and Neck Restraint. The anchor posts are made to rest flush on the helmet surface, accepting a variety of HNR anchor systems. ARAI GP-5W VENTILATION Closed-cockpit drivers need greater airflow when racing. The upper ventilation system of the GP-5W SA2020 helmet incorporates two exhaust vents and two large intake ducts to help keep the driver cool and comfortable. AVAILABLE VISOR SHIELDS FOR THE ARAI GP-5W Available shields for the Arai GP-5W are available here.  Arai anti-fog shields are available in clear, light tint and dark smoke. Standard shields also come in clear, light tint and dark smoke. Also, don't forget to check out the Competition Motorsport Performance Racing Helmet Bag to keep your new GP-5W safe and secure throughout each race weekend. The most effective helmet is one that fits properly. To measure your head, have an assistant use a dressmaker's tape or a piece of string to measure the circumference of your head. Start at a point about an inch above your eyebrows, looping around the back of your head at the point that results in the largest measurement, and finally around to the front again. It's a good idea to take two or three measurements to make sure you have the largest one. This helmet will ship to you with signature required for delivery.

Arai GP-5W Replacement Shields Replacement shields for the Arai GP-5W auto racing helmet.

Arai GP-7 SA2020 Helmet A driver favorite, the Arai GP-7 SA2020 helmet combines the most popular Arai features with new, improved upgrades. The Arai GP-7 is constructed with Arai’s own PBcLc (Peripherally Belted Complex Laminate) shell construction and the same shell shape as the Formula One-grade GP-7SRC model. New ventilation, a soft EPS liner, and a wider eye port for optimized peripheral vision are part of this new shell which gives the driver notable strength and flexibility. Replaceable cheek pads make racing comfortable for any driver, as do the three larger, closeable intake vents and two larger exhaust vents on the ventilation system. The Arai GP-7 helmet is Snell SA2020 certified with factory-installed M6 washers/nuts. Drivers of any skill level can install their own Head and Neck Restraint system using a 6mm bolt. The FIA-8859-2015 certification sticker is applied to the interior liner of the helmet. THE ARAI GP-7 AUTO RACING HELMET POSITIVE SHIELD LATCH Simple yet effective, the positive latch mechanism on the Arai GP-7 SA2020 helmet gives the driver solid shield latching, but is seamlessly integrated into the standard shield system for ease of use. NEW SHIELD PIVOT HARDWARE FOR THE ARAI GP-7 HELMET The Arai GP-7 SA2020 features new shield pivot hardware with improved aerodynamics based on the updated track slider design. An increased peripheral field of view is featured on the 6 series, which surpasses the 5 series in visibility. The wider eye port, shield, and pivot hardware were all developed on the RC and adapted to the Arai GP-7 SA2020 helmet. Additional Arai GP-7 shields in various tints and colors available here. ARAI GP-7 AUTO RACING HELMET VENTILATION Increased airflow is key to the GP-7 SA2020 helmet’s design. This includes bigger, closeable intake vents with large 10mm holes in both front and rear. Larger rear vents also provide better airflow. M6 ANCHORS FOR THE ARAI GP-7 HELMET Drivers of all skill levels will appreciate the integrated, pre-installed M6 threaded washer/nut with 6mm threads which accepts a range of Head and Neck Restraint devices. A flat surface area around the mounting nut will let the anchor post base to rest flush along the surface of the helmet and around the full perimeter of the anchor base. FIA-8859-2015 certification sticker applied to the interior liner material. NEW CHINBAR FOR THE ARAI GP-7 The Arai GP-7 SA2020’s new, ergonomic chinbar and ridge at the bottom edge of the shell lowers the center of gravity and increases the structural integrity of the helmet. Additional improvements include a rise in the shell above the shoulders for increased clearance. EJECT READY CROWN PAD OF THE ARAI GP-7 HELMET Arai's optional Eject system can be easily accommodated via a pre-cut pocket under the helmet’s crown pad. ARAI GP-7 HELMET SIZES XS (54cm) - L (60cm) ARAI GP-7 HELMET COLORS Gloss White and Matte Black Be sure to check out the Competition Motorsport Performance Racing Helmet Bag to keep your new Arai GP-7 safe and secure throughout each race weekend. The most effective helmet is one that fits properly. To measure your head, have an assistant use a dressmaker's tape or a piece of string to measure the circumference of your head. Start at a point about an inch above your eyebrows, looping around the back of your head at the point that results in the largest measurement, and finally around to the front again. It's a good idea to take two or three measurements to make sure you have the largest one. This helmet will ship with signature required for delivery.

Arai GP-7 Anti-Fog Helmet Shields Available in a variety of colors and tints, these replacement shields fit all versions of the Arai GP-7 SA2020 helmet.

Arai GP-7SRC 8860-2018     The new Arai GP-7SRC Carbon Fiber 8860-2018 auto racing helmet is a stunning example of Arai’s vision and technological mastery, engineered into a functional, real-world piece of safety equipment. It begins with a startling advancement: a proprietary carbon fiber weave that combines its existing properties of high strength and extreme light weight. Arai's proprietary carbon fiber has a property that standard carbon fiber does not possess: flexibility. (Standard carbon fiber tends to splinter or shatter instead of flex on impact.) The result is a helmet ready for the unparalleled demands and requirements of high end closed-cockpit racing. The remaining list of Arai GP-7SRC features and advances is impressive because, for this helmet and its prospective user, it simply has to be. The Arai GP-7SRC carbon fiber auto racing helmet meets or exceeds the latest FIA 8860-2018 homologation standards.  Additional Helmet shields for the Arai GP-7SRC helmet available here Ventilation Is Strong in the Arai GP-7SRC Carbon Large, closable intake vents combined with a 10mm vent greatly increase air intake. Larger 10mm rear vent hole increases air flow further compared to previous models. Arai's Innovative Positive Shield Latch Positive latch mechanism provides solid shield latching while allowing normal operation of the shield. Designed to be an integral component of the shield system, not just an add-on afterthought. Simplicity of the function belies the complexity of the design. Integrated HANS Post Anchors Integrated seats to accommodate a variety of Head and Neck Restraint devices. Pre-installed M6 threaded washer/nut with 6mm threads accepst a variety of anchor systems, making installation much easier. Flat surface area around the mounting nut allows the anchor post base to rest flush with the helmet surface. Proprietary Carbon Fiber Shell Construction Proprietary carbon fiber material and weave provide an extremely strong yet flexible material, helping manage impact energy. Multiple reinforcing materials are used to improve performance and keep weight and size to a minimum. Eject-Ready Crown Pad Integrates Exceptional Safety A pre-cut pocket under the crown pad can be easily removed to accommodate the optional eject system. Extremely Flexible Drink Tube Compatibility The GP-7SRC chin liner is easily removed to install a drink tube into the liner. The chin liner comes standard with four different drink hose placements. Add a Competition Motorsport Performance Racing Helmet Bag to keep your new Arai GP-7SRC Carbon Fiber helmet safe and secure throughout every race weekend. Getting The Best Fit for Your Arai GP-7SRC Carbon The Arai GP-7SRC 8860-2018 is available in sizes XS to Large. The most effective helmet is one that fits properly. To measure your head, have an assistant use a dressmaker's tape or a piece of string to measure the circumference of your head. Start at a point about an inch above your eyebrows, looping around the back of your head at the point that results in the largest measurement, and finally around to the front again. It's a good idea to take two or three measurements to make sure you have the largest one. This helmet will ship with signature required for delivery.

Arai GP-7SRC ABP Carbon Racing Helmet The Best Arai Auto Racing Helmet The new Arai GP-7SRC ABP is a stunning example of Arai’s vision and technological mastery, engineered into a functional, real-world piece of safety equipment. It begins with a startling advancement: a proprietary Carbon Fiber (CF) weave that combines CF’s existing benefits of high strength and extreme light weight. But there's a major added benefit that standard CF does not possess: flexibility. (Standard CF tends to splinter or shatter instead of flex on impact.) The result is a helmet ready for the unparalleled demands and requirements of high end closed-cockpit racing. The remaining list of Arai GP-7SRC features and advances is impressive because, for this helmet and its prospective user, it simply has to be. The Arai GP-7SRC ABP meets or exceeds the FIA 8860-2018 ABP homologation standard. Advanced Ballistic Protection The Formula One Standard FIA's new ABP (Advanced Ballistic Protection) specification is intended especially for drivers in open cars. The Arai GP-7SRC ABP has been strengthened in the forehead area, incorporating an external intrusion panel (previously mounted to the shield) that is now integrated into the helmet shell itself. The ABP homologation was written to reduce the risk of injury from debris or other objects striking a driver’s head. Arai GP-7SRC ABP 8860-2018 Carbon Fiber Ventilation Three large, close-able, intake vents combined with larger 10mm holes and two additional exhaust vents in the center of the helmet greatly increase air flow. A redesigned exhaust cowling improves aerodynamics, drawing out hot air escaping the helmet. The GP-7SRC comes with all vents unattached so you can customize the vent configuration to your specific needs. Arai Positive Shield Latch Arai's positive latch mechanism provides solid shield closure while allowing normal operation of the shield. Designed as an integral component of the shield system, not just an add-on afterthought, its functional simplicity belies the complexity of the design. Installed HANS Post Anchors Included Integrated seats accommodate a variety of Head and Neck Restraint devices. Pre-installed M6 threaded washer/nut with 6mm threads accepts a variety of anchor systems, making installation easy. The flat surface around the mounting nut allows the anchor post to rest flush on the helmet surface. Arai's Most Advanced ABP Carbon Fiber Shell Available in sizes XS through Large. Arai's proprietary carbon fiber material and weave provide an extremely strong yet flexible material, helping manage impact energy. Multiple reinforcing materials are used to improve performance while keeping weight and bulk to a minimum. Eject-Ready Crown Pad Pre-cut pocket under the crown pad can be easily removed to accommodate the optional eject system. Drink Tube Compatible The GP-7SRC chin liner is now more easily removed to install a drink tube into the liner. The chin liner comes standard with four different drink hose placements. This helmet will ship with signature required for delivery.

Arai SK-6 Adult Karting Helmet Being the dominant helmet on the Formula 1 grid, winning an IRL Championship, and protecting the heads of NASCAR heroes like Gordon, Burton, and Montoya has put Arai on the receiving end of an abundance of world-class racing helmet input. The Arai SK-6 Karting Helmet reaps the benefits of all this input. Designed by Arai specifically for karting, the SK-6 adds a ton of features and advancements to the already-impressive list of its predecessor. Make It Comfortable Then Add Lightness You won’t believe the comfort, lightness, and feeling of confidence the Arai SK-6 gives you, thanks to its incredibly strong, proprietary cLc (Complex Laminate Construction) shell. Its strength allowed Arai to give the SK-6 an extremely soft EPS liner for better comfort and impact energy management. If you’re serious about taking your karting to the next level, choose the helmet that’s already there. The Arai SK-6 is Snell K2020 certified. Arai SK-6 Adult Karting Helmet Details Positive shield lock mechanism provides solid latching, while allowing normal operation of the shield. Designed to be an integral component of the shield system and function, not just an add-on afterthought. The simplicity of the function masks the complexity of the design. A feature taken directly from the new Arai GP-6PED auto racing helmet. New shield pivot hardware improves aerodynamics. Type "6" 3mm shield. Wider eye port for increased peripheral field of view. Larger intake vent toggles for easier operation. Large rear vents for improved ventilation. Features taken directly from the new Arai GP-6PED auto racing helmet. New "Removable/Replaceable" cheek pad design allows for custom fitting with optional thicknesses (15mm, 20mm, 25mm, 30mm). Cheek pad covers are also removable to allow for easier and more thorough cleaning. Newly-sculpted chin bar and ridge along lower edge of shell to improve structural integrity. Provides a stronger shell near the opening where it is needed as well as lowers the center of gravity. Rise in shell above the shoulders for added clearance. An effective racing helmet is one that fits properly. Have an assistant use a measuring tape or a piece of string to measure the circumference of your head, starting at a point approximately one inch above the eyebrows in front, around a point in the back of the head that results in the largest possible measurement, and finally wrapping back to the front. It's a good idea to take several measurements and use the largest one.