All

A1-127 Girodisc Two-Piece 380mm Front Brake Rotors (Discontinued Design) FITMENT: Porsche 997.1 GT2/GT3 (2007-2011) w/ OEM PCCB Discontinued New old stock rotor.  These have the straight grooves as images show, not the new curved grooves.  Final Sale, no returns or exchanges. This Girodisc system is a direct 380mm replacement for the OEM front rotors on the Porsche 997.1 GT3/GT2 with OEM PCCB brakes. No modifications are necessary, allows use of factory unmodified pads unlike most aftermarket solutions for this application. The Girodisc rotors will bolt directly to the car and work with OEM calipers perfectly. By upgrading your brakes with lightweight, high performance replacements (as opposed to a big brake kit), your factory bias is maintained as well as your ABS efficiency. The central hat section of the disc is made from 6061-T6 aircraft specification aluminum. The disc is manufactured from cast iron constructed in the USA, made to the same specification with the same material used by professional racing organizations. The rotors' curved vane design was developed in racing and acts as a centrifugal pump to force cooling air through the disc. The rotor and hat mount together through a floating mount system which utilizes ten high strength alloy steel drive pins manufactured by Girodisc in the USA to their own specifications and are cadmium plated for corrosion resistance. The alloy drive pins transfer the load from the brake action while maintaining the axial and radial float between the disc rotor and hat. The pins are secured by Grade-12 cap screws with hardened washers and mounted with anti-noise spring washers to allow for heat expansion while eliminating the rattle and noise associated with floating rotors. The two-piece Girodisc design allows for disc-only replacement as well, minimizing future replacement costs and delivering outstanding performance. Sold/priced per pair.

AP Racing 380x34mm Replacement J Hook Rotor Rings Replacement Disc Only For AP Racing 13.01.20017 Rotor discs and installation hardware only. Center hat excluded. Fits The Following Cars (w/ OEM Iron Rotors) Porsche 991 GT3 (Front) Porsche 991 GT3RS (Front) Porsche 981 GT4 (Front) AP Racing by Essex 2-piece Competition J Hook front disc pair for 981 GT4, 991.1 & 991.2 GT3 & GT3 RS with iron discs 380mm x 34mm (14.96" x 1.34") 72 Vane, D66 Huge increase in airflow, cooling capacity, and durability vs. OEM discs Saves 2 lbs. unsprung weight per side vs. OEM iron discs Designed for: club racing, time trial, auto-x, HPDE Works with OEM calipers, no modifications required Ultralight, fully floating, anodized billet aluminum hat with float control/anti-rattle clips Sold/priced per pair of rotor rings (including hardware). AP Racing J Hook Brake Rotors – The Gold Standard in Track Day & Racing Performance Engineered for professional motorsport, HPDE, and dedicated track day use, AP Racing’s J Hook Brake Rotors deliver uncompromising performance, thermal stability, and consistent braking power. These two-piece, floating rotors are built to handle the extreme demands of road racing, with design features derived from over 50 years of elite competition—including Formula 1, NASCAR, and IMSA. Unlike conventional one-piece rotors, AP Racing’s two-piece floating design features a billet aluminum hat mated to a cast iron disc via precision-engineered bobbins. This setup allows for controlled radial expansion under high heat, minimizing distortion and coning. The result? More even pad wear, a firmer pedal feel, and longer component life, even during extended lapping sessions or endurance racing. Floating hardware includes anti-knockback spring clips that reduce piston retraction while eliminating common NVH issues like rattling. Why Choose AP Racing J Hook Rotors? Advanced Cooling, Superior Bite, Unmatched Durability At the heart of every rotor is AP Racing’s proprietary high-carbon iron alloy, developed to withstand repeated thermal cycling without cracking or warping. Internally, directional vanes—far superior to OEM pillar or straight vane designs—maximize airflow and cooling. With 60 to 84 vanes per rotor, AP Racing achieves faster heat evacuation, reduced brake fade, and a more consistent friction surface. These rotors are left/right-specific for optimal airflow and balance. The exclusive J Hook slot pattern offers enhanced initial bite and promotes uniform heat distribution across the rotor face, reducing pad deposits and vibration. Unlike drilled rotors or straight-slot competitors, the J Hook design provides cleaner pad transfer during bed-in and superior modulation under braking—ideal for serious drivers who demand feedback and control. Yes, you might hear a little more whirr, but you’ll gain the stopping power, consistency, and longevity your lap times demand. Premium Components, Affordable Performance The rotor hats are CNC-machined from 6061-T6 billet aluminum and hard anodized for strength and heat resistance. Scalloped edges under the hat further assist heat dissipation. All hardware is U.S.-made to AP Racing spec, the same quality found on pro-level racing platforms. And while these rotors are race-proven, they’re also surprisingly cost-effective to replace. Don’t settle for cheap rotors that crack after a weekend—AP’s J Hook rings offer better durability and real long-term value. Fewer replacements mean more track time, less downtime, and peace of mind knowing you're running the best. Used by Champions. Trusted by Experts. From endurance racers to HPDE enthusiasts, AP Racing brake rotors are trusted worldwide for their reliability, longevity, and performance under pressure. Whether you're shaving seconds off your lap time or building a dedicated track car, the J Hook delivers a professional-grade solution that won’t let you down. AP Racing J Hook Brake Rotors for Auto Racing, Track Days & HPDE Why Rotor Design Matters: Heat Expansion and Floating Technology As with most metals, iron brake discs expand significantly under heat. When temperatures rise, the disc grows radially—expanding in both diameter and circumference. Traditional one-piece rotors struggle to accommodate this natural expansion. As the outer edge pulls away from the center under heat stress, it creates a condition called “coning”—a distortion that compromises pad-to-rotor contact. This distortion can lead to uneven pad wear, brake tapering, and an inconsistent, long brake pedal. AP Racing two-piece floating brake rotors are purpose-built to eliminate these issues. Engineered with “float” built into the disc or hat assembly, these rotors feature oblong-shaped mounting holes that allow the hardware to slide as the disc heats up. This flexibility ensures the disc runs true within the caliper under high-temperature loads, effectively reducing distortion, minimizing pad taper and stress cracks, and promoting longer component life. Custom Mounting Hardware & Anti-Knockback Spring Clips AP Racing rotors utilize application-specific, U.S.-made mounting hardware—not generic bolts. These premium components are the exact parts used in AP’s professional motorsport products, engineered to withstand the rigors of competitive racing. To manage lateral disc motion that can push caliper pistons backward (known as knockback), AP Racing integrates anti-knockback spring clips on alternating bobbins—five on a ten-bolt setup, six on a twelve-bolt disc. These clips keep the aluminum hat and iron disc ring properly aligned while still allowing for radial float. Bonus: they eliminate annoying rattles and vibrations, ensuring a quieter, more refined braking experience. High-Performance Hat Design for Heat Isolation The disc hats in AP Racing’s two-piece floating rotors are CNC-machined from 6061-T6 billet aluminum and finished with a hard anodized coating. This high-strength aluminum alloy was selected for its ability to maintain structural integrity even at elevated temperatures. AP adds scalloped channels beneath the hat to further encourage airflow and heat evacuation from the outer disc face, minimizing thermal transfer to hubs and wheel bearings—helping reduce maintenance costs on these expensive components. Internal Vane Engineering: Airflow Optimization & Thermal Stability AP Racing’s internal vane design sets them apart from OEM and most aftermarket competitors. While many factory brake discs use non-directional pillar vanes (low-cost and NVH-focused), AP Racing rotors use directional vanes engineered for maximum airflow. These rotors are side-specific—meaning you’ll receive a unique left and right disc in each set—ensuring optimized cooling through strategic vane orientation and shape. Beyond that, AP Racing rotors feature a superior vane count, typically ranging from 60 to 84 vanes, compared to 30–48 in most aftermarket rotors. After extensive CFD and thermal analysis, this high vane count was proven to: Increase airspeed and thermal transfer Reduce recirculation and deflection at the disc face Minimize coning, cracking, and brake fade Deliver more even pad contact and extended rotor life J Hook Slot Pattern: Exclusive to AP Racing Slots and drill holes may improve initial bite, but they also introduce “cool spots” in the rotor face—areas of uneven heating that can lead to stress risers, cracks, and pad vibration. OEM rotors often avoid this by leaving the disc face blank, but that compromises bite and brake feel. AP Racing’s patented J Hook design, developed through rigorous R&D, solves this problem. The hooks are meticulously spaced around the disc’s circumference and from hat to edge, forming a continuous distortion path that ensures even heat distribution. This encourages uniform pad deposits during bed-in, helps reduce judder and cracking, and improves consistency under repeated high-load braking. In addition, the J Hook slots provide more leading edges for pads to grip than traditional curved slots or blank rotors. While this might generate a mild whirring sound during braking, the benefits—more bite, cleaner bedding, better pedal feel—make it the top choice for committed racers and serious track day drivers. Metallurgy Backed by 50+ Years of Motorsport Leadership AP Racing's reputation is built on performance, and their proprietary iron alloy used in J Hook rotors is no exception. Drawing from over five decades of elite motorsport experience, including 750+ Formula 1 wins and widespread use across NASCAR, AP’s engineers have developed a disc alloy that excels under sustained racing temperatures and stress. Where OEM discs focus on affordability and mass production, AP Racing’s J Hook rotors are purpose-built for motorsport durability and heat resistance. Affordable Replacement Cost: Serious Value for Serious Drivers Even the best brake rotors are consumables. When you drive hard—especially at the track—your discs will eventually wear out. That’s why AP Racing designed their replacement iron rings to be cost-effective, allowing you to replace worn parts without breaking the bank. Compare that to constantly buying cheap $150 rotors every weekend—rotors that can't handle the heat and need to be swapped frequently. With AP Racing’s J Hook rotors, you get longer service intervals, less downtime, and better performance over time, making them an incredibly smart long-term investment. Proven on Track. Trusted by Champions. Top-tier racing teams rely on AP Racing J Hook rotors for one reason: they perform under pressure. Whether you're running time trials, attending HPDE events, or competing in wheel-to-wheel racing, these rotors offer professional-grade reliability, safety, and performance. Bedding and Preparation of AP Racing J Hook Discs Properly preparing your new brake discs before heavy use is extremely important. The goal of bedding-in your brake pads and discs is to mate them together properly and prepare them for heavy use.  When prepared properly, or bed-in, your pads will transfer a thin layer of material to the disc face (transfer layer).  The pads in your caliper will then actually ride on that thin layer of pad material you’ve put down on the rotor, rather than rubbing directly on the iron rotor face.  A good transfer layer is going to give you superior brake pedal feel, less noise, superior pad wear, and lower the chances of cracking your discs. Important Notes- PLEASE READ! First, make sure you are on a closed course to perform a proper bed-in.  Do NOT perform the procedure on public roads.  You need a stretch of asphalt with long straights, good visibility, and no potential obstructions.  Make sure you are in a position to safely and repeatedly attain the necessary speeds to perform the bed-in procedure.  A controlled racetrack is the best place to perform this procedure.  AP Racing and Competition Motorsport in no way suggest or condone speeding on public roads or breaking the law in your car, nor do we take responsibility for any damage or injury that occurs as a result of using our product or these procedures.  You are performing the bed-in procedure at your own risk.  During these procedures, it’s critical that you never come to a complete stop with your foot on the brake pedal.  If you have brake ducts on your car, you may want to block them off to allow your brake system to heat up easily. The procedure outlined below is a generic procedure for most types of mild race pad.  Please check your pad manufacturer’s recommended bed-in procedure. Accelerate to approximately 60mph and then decelerate down to 5 mph.  If your car has ABS, you should try to hold the brakes at a point just before ABS intervention.  Once the car slows to 5mph, immediately accelerate back up to about 60mph, and brake again to roughly 5mph.  Repeat this series of stopping and accelerating 8 to 10 times.  Again, do not come to a complete stop with your foot on the brake pedal. Cool the brake system down by cruising at 45mph+ for 5 to 10 minutes. Visually inspect your discs.  They should be a blue/grey color (instead of shiny silver), and have an even layer of pad material across and around the entire rotor face. If the AP Racing rotors don’t have a layer of pad material on them, perform another series of stops in the manner outlined above.

Sparco Gulf Racing Driver Suit The Golden Age of Endurance Racing Brought Back to Life! In the golden years of endurance racing, Sparco and Gulf Racing contributed to the triumphs of the best racing drivers in the world. Now this partnership is renewed, and fans of the Gulf Racing historical livery have access to beautiful re-creations of the original Sparco products. All of Sparco's Gulf Racing reproductions have been updated with the newest Sparco safety technology and carry current FIA homologations. Classic Racing Heritage Meets Modern Technology The Sparco Gulf Racing Replica Race Suit is made with all-new lightweight three-layer fabric. It offers superior fire protection, breathability, and comfort when compared to the original worn back in the day. The suit features iconic Gulf Racing embroideries and patches to faithfully recreate the original look. The Gulf Racing replica race suit is made from Sparco's latest generation fabrics, offering a soft, lightweight outer fabric and breathable inserts at the sides, plus a large lower-back stretch panel for maximum comfort. The Sparco Gulf Racing Replica Race Suit also features a light-weight zipper and collar, pre-curved arms, pockets, classic tone-on-tone box quilt stitching and Sparco's signature epaulettes. Available in sizes EU48 - EU66. Sparco Gulf Replica Race Suit Details: Gulf Racing embroideries Lightweight three-layer fabric Pre-curved arms  Lightweight zipper and collar Breathable stretch panels FIA 8856-2018 approved Suit only (shoes, helmet, gloves, balaclava, house and car not included)

Sparco Martini Racing Driver Suit The Golden Age of Rally Racing Brought Back to Life! In the golden years of rally racing, Sparco and Martini Racing contributed to the triumphs of the best racing drivers in the world. Now this partnership is renewed, and fans of the Martini Racing historical livery have access to beautiful re-creations of the original Sparco products. All of Sparco's Martini Racing reproductions have been updated with the newest Sparco safety technology and carry current FIA homologations. Classic Racing Heritage Meets Modern Technology The Sparco Martini Racing Replica Race Suit is made with all-new lightweight three-layer fabric. It offers superior fire protection, breathability, and comfort when compared to the original worn back in the day. The suit features iconic Martini Racing embroideries and patches to faithfully recreate the original look. The Martini Racing replica race suit is made from Sparco's latest generation fabrics, offering a soft, lightweight outer fabric and breathable inserts at the sides, plus a large lower-back stretch panel for maximum comfort. The Sparco Martini Racing Replica Race Suit also features a light-weight zipper and collar, pre-curved arms, pockets, classic tone-on-tone box quilt stitching and Sparco's signature epaulettes. Available in sizes EU48 - EU66. Sparco Martini Replica Race Suit Details: Martini Racing embroideries Lightweight three-layer fabric Pre-curved arms  Lightweight zipper and collar Breathable stretch panels FIA approved

D1-228 Girodisc Front Rotor Ring Replacements (Super Trofeo) Lamborghini Huracan Super Trofeo ONLY REPLACEMENT ROTOR DISCS ONLY, DOES NOT INCLUDE ALUMINUM HAT. Competition Motorsport is an Authorized dealer for GiroDisc products and we are one of the largest stocking dealers in the country.  We ship most products same or next business day to ensure we meet your delivery deadline. The GiroDisc replacement rotor system is a direct rotor disc replacement for the OEM 2-piece hat and rotor and no modifications are necessary.   The rotor and hat mount together through a floating mount system which utilizes 8-10 high strength alloy steel drive pins manufactured by GiroDisc in the USA to our own specifications and are cadmium plated for corrosion resistance.  The alloy drive pins transfer the load from the brake action while maintaining the axial and radial float between the disc rotor and hat.  The pins are secured by grade 12 cap screws with hardened washers and mounted with anti-noise spring washers to allow for heat expansion while eliminating the rattle and noise associated with floating rotors. The 2-piece GiroDisc design allows for rotor only replacement to minimize replacement costs and deliver outstanding performance and cooling. Sold/Priced per pair.

A1-239 Girodisc Two-Piece Front Brake Rotors FITMENT: Chevy Camaro ZL1 (Gen 5) Competition Motorsport is an authorized dealer for Girodisc products and we are one of the largest stocking dealers in the country. We ship most products same or next business day to ensure we meet your delivery deadline. The Girodisc system is an upgrade to a two-piece steel rotor and aluminum hat combination and is a direct replacement for the OEM brake rotors. These two-piece floating rotors will bolt directly to the car and work with your OEM calipers perfectly. By upgrading your brakes with these lightweight, high-performance replacements (as opposed to a big brake kit), your factory brake bias is maintained, along with your ABS efficiency. Girodisc two-piece floating rotors are lighter than OEM brake rotors. This reduction in rotational mass and unsprung weight allows for quicker acceleration, sharper steering, and faster suspension response. When used with Pagid or PFC performance brake pads and CMS RF-1 brake fluid (available from Competition Motorsport), you have an amazing solution to overheating, cracking and warping rotors. The central hat section of each Girodisc is made from 6061-T6 aircraft specification aluminum. The disc is manufactured from cast iron constructed in the USA, made to the same specification with the same material used by professional racing organizations. The rotors' curved vane design was developed in racing and acts as a centrifugal pump to force cooling air through the disc. The rotor and hat mount together through a floating mount system which utilizes ten high strength alloy steel drive pins manufactured by Girodisc in the USA to their own specifications and are cadmium plated for corrosion resistance. The alloy drive pins transfer the load from the brake action while maintaining the axial and radial float between the disc rotor and hat. The pins are secured by class 12.9 cap screws with hardened washers and mounted with anti-noise spring washers to allow for heat expansion while eliminating the rattle and noise associated with floating rotors. The two-piece Girodisc design allows for disc-only replacement as well, minimizing future replacement costs and delivering outstanding performance. Sold/priced per pair.

A1-211 Girodisc 2pc Front Brake Rotors FITMENT: Chevy Camaro ZL1 (Gen 6), Front The Girodisc system is a direct replacement for the OE disc, but a different brake pad with an annulus (pad swept area) of 66mm or less must be used. We strongly recommend the Pagid 8081. This reduction in rotor annulus is done to keep the weight of the rotors low. The OEM rotors utilize a pillar vane design which is horribly inefficient in terms of dissipating heat. Since the OEM rotors heat-soak very easily, Chevrolet chose an easy solution to this problem: increasing the rotors' mass to combat that heat. We weighed an OEM rotor at 32.5 lbs. -- holy smoke! Girodisc took the functional route instead, engineering a shorter-annulus rotor ring for a total rotor-and-hat weight of 28.0 lbs. This design utilizes 72 directional cooling vanes for an incredibly efficient and robust package. The necessary pad shape is very common, found on other Camaro and Corvette applications equipped with six-piston calipers. If there's a specific pad compound you're after please contact us at (844) 438-7244 and we'll get you what you need! The central hat section of each Girodisc is made from 6061-T6 aircraft specification aluminum. The disc is manufactured from cast iron constructed in the USA, made to the same specification with the same material used by professional racing organizations. The rotors' curved vane design was developed in racing and acts as a centrifugal pump to force cooling air through the disc. The rotor and hat mount together through a floating mount system which utilizes ten high strength alloy steel drive pins manufactured by Girodisc in the USA to their own specifications and are cadmium plated for corrosion resistance. The alloy drive pins transfer the load from the brake action while maintaining the axial and radial float between the disc rotor and hat. The pins are secured by Grade-12 cap screws with hardened washers and mounted with anti-noise spring washers to allow for heat expansion while eliminating the rattle and noise associated with floating rotors. The two-piece Girodisc design allows for disc-only replacement as well, minimizing future replacement costs and delivering outstanding performance. Sold/priced per pair.

A2-162 Girodisc 2pc Front Brake Rotors Rear Fitment, Ford Shelby GT350/GT350R (2015+) The Girodisc system for the 2015+ Ford Shelby GT350 and GT350R is a direct replacement for the OE rear discs; no modifications are necessary. The rotors will bolt directly to your car and work flawlessly with OE calipers. By upgrading your brakes with lightweight, high performance two-piece rotors, as opposed to a big brake kit, your factory brake bias is maintained as well as your ABS effectiveness and efficiency. Together with our customers, we have thousands of track miles on Girodisc rotors on every conceivable car. They are the go-to rotor for any of our track- or race-car builds. The central hat section of the Girodisc A2-162 rotor is made from strictly U.S. sourced 6061-T6 aircraft specification aluminum. The disc is made from Girodisc's proprietary cast iron, poured in the USA and machined from start to finish in-house at Girodisc. The rotor utilizes a curved vane design, developed in racing to act as a centrifugal pump to force cooling air through the disc. The rotor and hat have a floating mount system, which utilizes 10 high-strength alloy steel drive pins, manufactured by Girodisc in the USA to their specifications and cadmium plated for a long lasting corrosion resistance. These pins take the load from braking action while maintaining the axial and radial float between the hat and disc. The pins are secured by Grade-12 cap screws with hardened washers. In order to keep the rotors from making noise when cold, the pins are mounted with anti-noise spring washers on the rotor side which allow the rotor to grow with heat expansion but eliminate the rattle and noise associated with floating rotors. This float also allows the rotor to self center between the pads. Once the Girodisc system is in place, simply replace the cast iron rotor ring when needed. Sold/priced per pair.

A1-157 Girodisc Two-Piece Front Brake Rotors Fitment: BMW E9x M3 Competition Motorsport is an authorized dealer for Girodisc products and we are one of the largest stocking dealers in the country. We ship most products same or next business day to ensure we meet your delivery deadline. The Girodisc system is an upgrade to a two-piece steel rotor and aluminum hat combination and is a direct replacement for the OEM brake rotors. These two-piece floating rotors will bolt directly to the car and work with your OEM calipers perfectly. By upgrading your brakes with these lightweight, high-performance replacements (as opposed to a big brake kit), your factory brake bias is maintained, along with your ABS efficiency. Girodisc two-piece floating rotors are lighter than OEM brake rotors. This reduction in rotational mass and unsprung weight allows for quicker acceleration, sharper steering, and faster suspension response. When used with Pagid or PFC performance brake pads, and Competition Motorsport RF-1 brake fluid (available from Competition Motorsport), you have an amazing solution to overheating, cracking and warping rotors. The central hat section of the disc is made from 6061-T6 aircraft specification aluminum. The disc is manufactured from cast iron constructed in the USA, made to the same specification with the same material used by professional racing organizations. The rotors' curved vane design was developed in racing and acts as a centrifugal pump to force cooling air through the disc. The rotor and hat mount together through a floating mount system which utilizes ten high strength alloy steel drive pins manufactured by Girodisc in the USA to their own specifications and are cadmium plated for corrosion resistance. The alloy drive pins transfer the load from the brake action while maintaining the axial and radial float between the disc rotor and hat. The pins are secured by Grade-12 cap screws with hardened washers and mounted with anti-noise spring washers to allow for heat expansion while eliminating the rattle and noise associated with floating rotors. The two-piece Girodisc design allows for disc-only replacement as well, minimizing future replacement costs and delivering outstanding performance. Sold/priced per pair.

A1-162 Girodisc 2pc Front Brake Rotors Front Fitment, Ford Shelby GT350/GT350R (2015+) This Girodisc system for the Ford Shelby GT350 and GT350R is a direct replacement for the OEM front brake rotors; no modifications are necessary. The rotors will bolt directly to your Shelby and work flawlessly with the OEM calipers. By upgrading your brakes with lightweight, high performance two-piece floating rotors (as opposed to a big brake kit) your factory dialed-in brake bias is maintained as well as your ABS effectiveness and efficiency. Together with our customers, we have thousands of track miles on Girodisc rotors on every conceivable car. They are the go-to rotor for any of our track-day and race-car builds. Girodisc two-piece floating rotors are lighter than OEM brake rotors. This reduction in rotational mass and unsprung weight allows for quicker acceleration, sharper steering, and faster suspension response. When used with Pagid or PFC performance brake pads and CMS RF-1 racing brake fluid (available from Competition Motorsport), you have an amazing solution to overheating, cracking and warping rotors. The central hat section of each Girodisc is made from 6061-T6 aircraft specification aluminum. The disc is manufactured from cast iron constructed in the USA, made to the same specification with the same material used by professional racing organizations. The rotors' curved vane design was developed in racing and acts as a centrifugal pump to force cooling air through the disc. The rotor and hat mount together through a floating mount system which utilizes ten high strength alloy steel drive pins manufactured by Girodisc in the USA to their own specifications and are cadmium plated for corrosion resistance. The alloy drive pins transfer the load from the brake action while maintaining the axial and radial float between the disc rotor and hat. The pins are secured by Grade-12 cap screws with hardened washers and mounted with anti-noise spring washers to allow for heat expansion while eliminating the rattle and noise associated with floating rotors. The two-piece Girodisc design allows for disc-only replacement as well, minimizing future replacement costs and delivering outstanding performance. Sold/priced per pair.

A1-035 Girodisc 2pc Front Brake Rotors (340mm) FITS: Porsche 981 Boxster/Cayman base model (2013-2016) Competition Motorsport is an authorized dealer for Girodisc products. As one of the largest stocking dealers in the country, we ship most products the same or next business day to ensure we meet your delivery deadline. This Girodisc system upgrades the 325mm OEM one-piece rotors to a 340mm two-piece steel disc and aluminum hat. Machined aluminum caliper spacers are included to accommodate the larger Girodiscs. This two-piece "floating rotor" design will bolt directly to your Porsche 981 front and work flawlessly with the OEM calipers. Upgrading your brakes to lightweight, high-performance Girodisc rotors, you maintain the factory brake bias and ABS effectiveness. Much lighter than the OEM rotors, Girodisc rotors reduce rotational and unsprung mass giving you stronger braking and faster suspension response. Combined with Pagid or PFC performance brake pads and Competition Motorsport RF-1 racing brake fluid, Girodisc rotors are the ultimate solution to overheated, cracked, warped rotors that result from high-performance driving. The central hat of the rotor is made from 6061-T6 aircraft aluminum. The disc is manufactured in the USA from the same cast iron used by professional racing organizations. Its curved-vane design, developed in racing, acts like a centrifugal pump forcing cool air through the disc. The disc and hat mount together through a floating mount system using ten cadmium plated, high-strength alloy steel drive pins manufactured by Girodisc. These drive pins transfer braking load while maintaining axial and radial float between the disc and hat to allow for heat expansion. Anti-noise spring washers eliminate the noise typically associated with floating rotors. This two-piece Girodisc design allows for disc-only replacement, reusing the hat to minimize maintenance costs. Sold/priced per pair.

Girodisc A1-031 Two-Piece Front Brake Rotors (340mm) FITS PORSCHE: 986 Boxster (front) 987 Boxster S/Cayman S (front) 996 Carrera 2/Carrera 4(front) 997.1 Carrera 2/Carrera 4(front) Competition Motorsport is an authorized dealer for Girodisc products. As one of the largest stocking dealers in the country, we ship most products the same or next business day to ensure we meet your delivery deadline. This Girodisc system upgrades the 317mm OEM one-piece front rotors to 340mm two-piece steel discs and aluminum hats. Caliper spacers are included to accommodate the larger rotors. This two-piece "floating rotor" design will bolt directly to your Porsche front and work flawlessly with the OEM calipers. Upgrading your brakes to lightweight, high-performance Girodisc rotors, you maintain the factory brake bias and ABS effectiveness. Much lighter than the OEM rotors, Girodisc rotors reduce rotational and unsprung mass giving you stronger braking and faster suspension response. Combined with Pagid or PFC performance brake pads and Competition Motorsport RF-1 racing brake fluid, Girodisc rotors are the ultimate solution to overheated, cracked, warped rotors that result from high-performance driving. The central hat of the rotor is made from 6061-T6 aircraft aluminum. The disc is manufactured in the USA from the same cast iron used by professional racing organizations. Its curved-vane design, developed in racing, acts like a centrifugal pump forcing cool air through the disc. The disc and hat mount together through a floating mount system using ten cadmium plated, high-strength alloy steel drive pins manufactured by Girodisc. These drive pins transfer braking load while maintaining axial and radial float between the disc and hat to allow for heat expansion. Anti-noise spring washers eliminate the noise typically associated with floating rotors. This two-piece Girodisc design allows for disc-only replacement, reusing the hat to minimize maintenance costs. Sold/priced per pair.

PORSCHE 981 CAYMAN/BOXSTER BASE AND S (2013+) The Girodisc system is an upgrade to a 325mm two-piece steel rotor and aluminum hat combination and is a direct replacement for the OEM brake disc. The two-piece floating disc will bolt directly to the car and work with OEM calipers perfectly. By upgrading your brakes with these lightweight high-performance replacements as opposed to a big brake kit, your factory bias is maintained as well as your ABS efficiency. The Girodisc rotors are lighter than OEM pieces. The reduction in rotational and unsprung weight allows for quicker acceleration and suspension response. When used with Girodisc Magic Pads on the street, Pagid or PFC racing pads on track, and Competition Motorsport RF1 brake fluid (all available from Competition Motorsport), you have an amazing solution to overheating, cracking and warping rotors. The central hat section of the disc is made from 6061-T6 aircraft specification aluminum. The disc is manufactured from cast iron which is constructed in the USA and is made to the same specification with the same material used by professional racing organizations. The rotors curved vane design was developed in racing and acts as a centrifugal pump to force cooling air through the disc. The rotor and hat mount together through a floating mount system which utilizes 8-10 high strength alloy steel drive pins manufactured by Girodisc in the USA to their own specifications and are cadmium plated for corrosion resistance. The alloy drive pins transfer the load from the brake action while maintaining the axial and radial float between the disc rotor and hat. The pins are secured by Grade 12 cap screws with hardened washers and mounted with anti-noise spring washers to allow for heat expansion while eliminating the rattle and noise associated with floating rotors. The two-piece Girodisc design allows for rotor only replacement as well to minimize future replacement costs. Sold/Priced per pair

Girodisc A2-031 Two Piece Floating Racing Brake Rotors (325mm) The Girodisc system is an upgrade to a 325mm 2-piece steel rotor and aluminum hat combination and is a direct replacement for the OEM brake disc. The 2-piece floating disc will bolt directly to the car and work with OEM calipers perfectly. By upgrading your brakes with these lightweight high-performance replacements as opposed to a big brake kit, your factory bias is maintained as well as your ABS efficiency. The Girodisc rotors are lighter than OEM pieces. The reduction in rotational and unsprung weight allows for quicker acceleration and suspension response. When used with Pagid or PFC racing brake pads and Competition Motorsport Performance RF-1 racing brake fluid, you have an amazing solution to overheating, cracking and warping rotors. The central hat section of the disc is made from 6061-T6 aircraft specification aluminum. The disc is manufactured from cast iron which is constructed in the USA and is made to the same specification with the same material used by professional racing organizations. The rotors curved vane design was developed in racing and acts as a centrifugal pump to force cooling air through the disc. The rotor and hat mount together through a floating mount system which utilizes 8-10 high strength alloy steel drive pins manufactured by Girodisc in the USA to our own specifications and are cadmium plated for corrosion resistance. The alloy drive pins transfer the load from the brake action while maintaining the axial and radial float between the disc rotor and hat. The pins are secured by grade12 cap screws with hardened washers and mounted with anti-noise spring washers to allow for heat expansion while eliminating the rattle and noise associated with floating rotors. The 2-piece Girodisc design allows for rotor only replacement as well to minimize future replacement costs and deliver outstanding performance and cooling. Sold/priced per pair.

A1-103 Girodisc 2pc Front Brake Rotors FITMENT: Porsche 911 Turbo and RS, Front (993) Competition Motorsport is an authorized dealer for Girodisc products and we are one of the largest stocking dealers in the country. We ship most products same or next business day to ensure we meet your delivery deadline. The Girodisc system is an upgrade to a two-piece steel rotor and aluminum hat combination and is a direct replacement for the OEM brake rotors. These two-piece floating rotors will bolt directly to the car and work with your OEM calipers perfectly. By upgrading your brakes with these lightweight, high-performance replacements (as opposed to a big brake kit), your factory brake bias is maintained, along with your ABS efficiency. Girodisc two-piece floating rotors are lighter than OEM brake rotors. This reduction in rotational mass and unsprung weight allows for quicker acceleration, sharper steering, and faster suspension response. When used with Pagid or PFC performance brake pads, and Competition Motorsport RF-1 brake fluid (available from Competition Motorsport), you have an amazing solution to overheating, cracking and warping rotors. The central hat section of the disc is made from 6061-T6 aircraft specification aluminum. The disc is manufactured from cast iron constructed in the USA, made to the same specification with the same material used by professional racing organizations. The rotors' curved vane design was developed in racing and acts as a centrifugal pump to force cooling air through the disc. The rotor and hat mount together through a floating mount system which utilizes ten high strength alloy steel drive pins manufactured by Girodisc in the USA to their own specifications and are cadmium plated for corrosion resistance. The alloy drive pins transfer the load from the brake action while maintaining the axial and radial float between the disc rotor and hat. The pins are secured by Grade-12 cap screws with hardened washers and mounted with anti-noise spring washers to allow for heat expansion while eliminating the rattle and noise associated with floating rotors. The two-piece Girodisc design allows for disc-only replacement as well, minimizing future replacement costs and delivering outstanding performance. Sold/priced per pair.