Porsche Brake Rotors

Girodisc Porsche 996, 997.1 Carrera Rear Rotors (Includes Spacers & Bolts) Boost the braking performance of your Porsche 996 or 997.1 Carrera with Girodisc’s lightweight two-piece rear rotors. This kit includes all necessary spacers and hardware, allowing a direct OEM installation while upgrading rotor diameter from 298mm to 325mm—improving cooling, braking leverage, and overall stopping consistency. Vehicle Fitment Porsche 996 Carrera / Carrera 4 / Carrera 4SPorsche 997.1 Carrera / Carrera SIncludes caliper spacers and bolts for installationDirect replacement – compatible with factory calipers and hardware Engineered for Porsche Precision The Girodisc system replaces the factory rotor with a larger, two-piece floating design engineered for performance and longevity. Each assembly pairs a CNC-machined 6061-T6 aluminum hat with Girodisc’s proprietary cast-iron friction rings, both made in the USA. The curved internal vane structure acts as a centrifugal pump, forcing air through the rotor for enhanced cooling. With its increased rotor size and floating design, this upgrade delivers superior heat management and more consistent braking under repeated high-speed stops. Features • Direct OEM replacement – includes spacers and bolts• Increases rotor diameter from 298mm to 325mm• 6061-T6 billet aluminum hats, machined and anodized in the USA• Proprietary cast-iron friction rings poured and finished in-house• Floating mount design with cadmium-plated steel drive pins• Anti-noise spring washers eliminate rattle and manage heat expansion• Curved internal vane design maximizes airflow and cooling• Reduces unsprung and rotational mass for sharper handling• Maintains factory brake bias and ABS calibration• Fully rebuildable – replace only friction rings when needed• Sold/priced per pair Girodisc A2-033 Rear Rotor FAQs: Why is this rotor larger than stock? The Girodisc system increases diameter to 325mm, providing greater mechanical leverage and improved heat capacity for stronger, more consistent braking. Do I need to modify my calipers to fit these? No. The kit includes custom spacers and bolts that perfectly reposition the calipers for the larger rotors—no cutting or permanent changes required. Will these affect brake bias or ABS? Not at all. Girodisc engineers each system to maintain the factory balance and ABS performance while increasing cooling efficiency. Are they suitable for track or aggressive driving? Absolutely. The curved vane design and floating assembly deliver exceptional fade resistance and durability, making them ideal for spirited street or track use. Upgrade your Porsche’s stopping power with Girodisc rear rotors—engineered to bring race-level precision and confidence to your 996 or 997.1 Carrera.

Porsche 991.1 S, 4S, GTS Front Rotors The Girodisc 2-piece floating rotor system is a direct replacement for the factory rotors on the Porsche 991.1 Carrera S, 4S, and GTS. This upgrade includes precision caliper spacers that allow the installation of larger 350 mm rotors in place of the factory 340 mm discs, resulting in increased braking torque, improved cooling, and reduced fade under demanding conditions. The Girodisc rotors weigh approximately 21.0 lbs each, compared to the 24.4 lbs OEM units—reducing rotational mass for sharper acceleration and suspension response. Each rotor features a CNC-machined 6061-T6 aluminum hat bolted to Girodisc’s proprietary high-carbon cast-iron rings. The internal curved vane design functions as a centrifugal air pump, pulling cool air through the disc to efficiently dissipate heat during high-performance driving. Engineered and manufactured entirely in the USA, Girodisc rotors deliver exceptional braking consistency and reliability on both street and track. Precision-Engineered Performance A1-122 Girodisc Porsche 991.1 S, 4S, GTS Front Rotor Vehicle Fitment Porsche 991.1 Carrera S Porsche 991.1 Carrera 4S Porsche 991.1 Carrera GTS A1-122 Girodisc Porsche 991.1 S, 4S, GTS Front Rotor Features Direct replacement with included spacers: Increases rotor size to 350 mm for enhanced braking force and heat management. Lightweight construction: 21.0 lbs per rotor versus 24.4 lbs OEM reduces unsprung and rotational weight. Curved vane design: Actively circulates air through the rotor for superior cooling and fade resistance. Floating mount system: Cadmium-plated steel drive pins and anti-noise spring washers manage thermal expansion while eliminating rattle. Serviceable two-piece design: Replace only the iron rings when worn for reduced long-term cost. Made in the USA: Cast, machined, and assembled entirely in-house for unmatched quality control. A1-122 Girodisc Porsche 991.1 S, 4S, GTS Front Rotor FAQs Will these work with OEM calipers? Yes. Girodisc rotors are designed to work perfectly with stock calipers and come with spacers for proper fitment. Do I need to change brake pads? No. You can continue using your current OEM or aftermarket pads. Are these suitable for track use? Yes. The curved vane design and floating assembly ensure consistent braking under extreme temperatures. Do they affect ABS or brake balance? No. Factory brake bias and ABS functionality remain unchanged. How are they sold? Sold and priced per pair. Upgrade your 991.1 Carrera with Girodisc’s 350 mm floating rotors for improved cooling, reduced fade, and sharper pedal feel—engineered for performance driving enthusiasts.

AP Racing by Essex 2-piece "S" Vane J Hook Front Brake Rotors (Front 408 x 34mm)- Porsche 992 Turbo Iron Rotors Fit The Following Cars (w/ OEM Iron Rotors) Porsche 992 Turbo OEM Iron (Front) Sold/priced per pair. AP Racing 2-piece S Vane Competition J Hook front disc pair for GT4RS with iron or PCCB discs. Massive increase in airflow, cooling capacity, and durability vs. OEM discs or even conventional curved vane discs 408mm x 34mm (16.06" x 1.34") , 84 Sinusoidal "wave" vanes, D62 radial depth Designed for: club racing, time trial, autocross, HPDE Works with OEM calipers, no modifications required Ultralight, fully floating, anodized billet aluminum hat with float control/anti-rattle clips We are introducing a new internal vane technology in our front 2-piece discs for the GT4RS. It is called the Sinusoidal Vane, which AP sometimes refers to internally as the 'Wave' Vane for obvious reasons as you’ll see below. This tech is something that has helped AP Racing brake systems win championships in international GT racing, as well as multiple NASCAR Cup championships here in North America. As one of the most desirable track weapons on the planet, we wanted the GT4RS to be the first production car application for this technology in North America. Just as AP Racing's Radi-CAL calipers set a new benchmark for caliper stability, cooling, and durability, the Sinusoidal Vanes have done the same for iron racing discs. The concept for this disc design originated in NASCAR Cup. Up until the debut of the Next Gen car (for which AP/Essex are supplying the spec brake package), we were cramming our brake systems inside tiny 15” wheels. Trying to squeeze adequate brake thermal mass into a wheel that small is incredibly challenging, particularly when you have a 1,000 HP and 3,000 pounds mashing on them every few seconds from 200 mph…for hours on end! In a wheel that small, there isn’t anywhere for the heat to go, and the durability of every component is crucial. We were constantly looking for ways to provide the Cup teams with increased durability, stability, and cooling, and that’s what led AP to this technology. Benefits of the Wave Vane disc technology vs. traditional curved vanes: Increased thermal stability- Wild temperature swings are what causes discs to crack. When you stand on the brakes for an approaching corner, your disc temperatures skyrocket and the iron expands. As you travel down the subsequent straight, the discs are blasted with cooling air. The longer the straight and the higher the speed, the greater the temperature drop, and the further the iron contracts. This expansion and contraction cycle places a huge amount of stress on the iron and is what causes them to eventually crack. That’s why tracks with relatively slow corners at the end of high-speed straights, followed by another long straight, decimate brake discs (think Watkins Glen or Road America). In an ideal world, once you brought your discs up to race temps, you would keep them at a constant temperature for the entire session. The Sinusoidal Vane brings the discs closer to that goal by decreasing the difference between the maximum and minimum disc temperature by as much as 35%. That means a less dramatic temperature swing and greater crack resistance and durability. Reduced maximum disc temperatures by 10%+: Not only are temperature swings less intense with the Wave Vane, the maximum temperatures reached are substantially lower. For example, in one NASCAR test the Wave Vane discs showed a peak temp of 1328F and a minimum temp of 1085F (delta of 243F), while the traditional curved vanes maxed out at 1490F and a min of 1121F (delta of 369F). Not only was the difference between min and max more subdued, the max temperature reached by the Wave Vane disc was 162F lower! Increased cooling surface area- Each of the internal Wave Vanes has a larger cooling surface area vs. a traditional curved vane. Greater support for the disc face- A disc’s internal vane structure provides the support lattice behind the disc face. Having many internal vanes impacts airspeed and heat transfer through the disc, reduces air recirculation between vanes, and reduces deflection at the disc face. In practical terms, a disc with a high number of vanes is more thermally stable, maintains more even contact with the brake pads (which reduces uneven pad deposits/judder), and is less prone to distortion. In summary, the Wave Vane design provides even greater support for the disc face than AP’s standard curved vane designs. Reduced weight- The Wave Vane design provides a slight unsprung weight reduction vs. a similar disc with curved internal vanes. AP Racing J Hook Brake Rotors – The Gold Standard in Track Day & Racing Performance Engineered for professional motorsport, HPDE, and dedicated track day use, AP Racing’s J Hook Brake Rotors deliver uncompromising performance, thermal stability, and consistent braking power. These two-piece, floating rotors are built to handle the extreme demands of road racing, with design features derived from over 50 years of elite competition—including Formula 1, NASCAR, and IMSA. Unlike conventional one-piece rotors, AP Racing’s two-piece floating design features a billet aluminum hat mated to a cast iron disc via precision-engineered bobbins. This setup allows for controlled radial expansion under high heat, minimizing distortion and coning. The result? More even pad wear, a firmer pedal feel, and longer component life, even during extended lapping sessions or endurance racing. Floating hardware includes anti-knockback spring clips that reduce piston retraction while eliminating common NVH issues like rattling. Why Choose AP Racing J Hook Rotors? Advanced Cooling, Superior Bite, Unmatched Durability At the heart of every rotor is AP Racing’s proprietary high-carbon iron alloy, developed to withstand repeated thermal cycling without cracking or warping. Internally, directional vanes—far superior to OEM pillar or straight vane designs—maximize airflow and cooling. With 60 to 84 vanes per rotor, AP Racing achieves faster heat evacuation, reduced brake fade, and a more consistent friction surface. These rotors are left/right-specific for optimal airflow and balance. The exclusive J Hook slot pattern offers enhanced initial bite and promotes uniform heat distribution across the rotor face, reducing pad deposits and vibration. Unlike drilled rotors or straight-slot competitors, the J Hook design provides cleaner pad transfer during bed-in and superior modulation under braking—ideal for serious drivers who demand feedback and control. Yes, you might hear a little more whirr, but you’ll gain the stopping power, consistency, and longevity your lap times demand. Premium Components, Affordable Performance The rotor hats are CNC-machined from 6061-T6 billet aluminum and hard anodized for strength and heat resistance. Scalloped edges under the hat further assist heat dissipation. All hardware is U.S.-made to AP Racing spec, the same quality found on pro-level racing platforms. And while these rotors are race-proven, they’re also surprisingly cost-effective to replace. Don’t settle for cheap rotors that crack after a weekend—AP’s J Hook rings offer better durability and real long-term value. Fewer replacements mean more track time, less downtime, and peace of mind knowing you're running the best. Used by Champions. Trusted by Experts. From endurance racers to HPDE enthusiasts, AP Racing brake rotors are trusted worldwide for their reliability, longevity, and performance under pressure. Whether you're shaving seconds off your lap time or building a dedicated track car, the J Hook delivers a professional-grade solution that won’t let you down.   AP Racing J Hook Brake Rotors for Auto Racing, Track Days & HPDE Why Rotor Design Matters: Heat Expansion and Floating Technology As with most metals, iron brake discs expand significantly under heat. When temperatures rise, the disc grows radially—expanding in both diameter and circumference. Traditional one-piece rotors struggle to accommodate this natural expansion. As the outer edge pulls away from the center under heat stress, it creates a condition called “coning”—a distortion that compromises pad-to-rotor contact. This distortion can lead to uneven pad wear, brake tapering, and an inconsistent, long brake pedal. AP Racing two-piece floating brake rotors are purpose-built to eliminate these issues. Engineered with “float” built into the disc or hat assembly, these rotors feature oblong-shaped mounting holes that allow the hardware to slide as the disc heats up. This flexibility ensures the disc runs true within the caliper under high-temperature loads, effectively reducing distortion, minimizing pad taper and stress cracks, and promoting longer component life. Custom Mounting Hardware & Anti-Knockback Spring Clips AP Racing rotors utilize application-specific, U.S.-made mounting hardware—not generic bolts. These premium components are the exact parts used in AP’s professional motorsport products, engineered to withstand the rigors of competitive racing. To manage lateral disc motion that can push caliper pistons backward (known as knockback), AP Racing integrates anti-knockback spring clips on alternating bobbins—five on a ten-bolt setup, six on a twelve-bolt disc. These clips keep the aluminum hat and iron disc ring properly aligned while still allowing for radial float. Bonus: they eliminate annoying rattles and vibrations, ensuring a quieter, more refined braking experience. High-Performance Hat Design for Heat Isolation The disc hats in AP Racing’s two-piece floating rotors are CNC-machined from 6061-T6 billet aluminum and finished with a hard anodized coating. This high-strength aluminum alloy was selected for its ability to maintain structural integrity even at elevated temperatures. AP adds scalloped channels beneath the hat to further encourage airflow and heat evacuation from the outer disc face, minimizing thermal transfer to hubs and wheel bearings—helping reduce maintenance costs on these expensive components. J Hook Slot Pattern: Exclusive to AP Racing Slots and drill holes may improve initial bite, but they also introduce “cool spots” in the rotor face—areas of uneven heating that can lead to stress risers, cracks, and pad vibration. OEM rotors often avoid this by leaving the disc face blank, but that compromises bite and brake feel. AP Racing’s patented J Hook design, developed through rigorous R&D, solves this problem. The hooks are meticulously spaced around the disc’s circumference and from hat to edge, forming a continuous distortion path that ensures even heat distribution. This encourages uniform pad deposits during bed-in, helps reduce judder and cracking, and improves consistency under repeated high-load braking. In addition, the J Hook slots provide more leading edges for pads to grip than traditional curved slots or blank rotors. While this might generate a mild whirring sound during braking, the benefits—more bite, cleaner bedding, better pedal feel—make it the top choice for committed racers and serious track day drivers. Metallurgy Backed by 50+ Years of Motorsport Leadership AP Racing's reputation is built on performance, and their proprietary iron alloy used in J Hook rotors is no exception. Drawing from over five decades of elite motorsport experience, including 750+ Formula 1 wins and widespread use across NASCAR, AP’s engineers have developed a disc alloy that excels under sustained racing temperatures and stress. Where OEM discs focus on affordability and mass production, AP Racing’s J Hook rotors are purpose-built for motorsport durability and heat resistance. Affordable Replacement Cost: Serious Value for Serious Drivers Even the best brake rotors are consumables. When you drive hard—especially at the track—your discs will eventually wear out. That’s why AP Racing designed their replacement iron rings to be cost-effective, allowing you to replace worn parts without breaking the bank. Compare that to constantly buying cheap $150 rotors every weekend—rotors that can't handle the heat and need to be swapped frequently. With AP Racing’s J Hook rotors, you get longer service intervals, less downtime, and better performance over time, making them an incredibly smart long-term investment. Proven on Track. Trusted by Champions. Top-tier racing teams rely on AP Racing J Hook rotors for one reason: they perform under pressure. Whether you're running time trials, attending HPDE events, or competing in wheel-to-wheel racing, these rotors offer professional-grade reliability, safety, and performance. Bedding and preparation of AP Racing J Hook Disc Properly preparing your new brake discs before heavy use is extremely important. The goal of bedding-in your brake pads and discs is to mate them together properly and prepare them for heavy use.  When prepared properly, or bed-in, your pads will transfer a thin layer of material to the disc face (transfer layer).  The pads in your caliper will then actually ride on that thin layer of pad material you’ve put down on the rotor, rather than rubbing directly on the iron rotor face.  A good transfer layer is going to give you superior brake pedal feel, less noise, superior pad wear, and lower the chances of cracking your discs. Important Notes- PLEASE READ! First, make sure you are on a closed course to perform a proper bed-in.  Do NOT perform the procedure on public roads.  You need a stretch of asphalt with long straights, good visibility, and no potential obstructions.  Make sure you are in a position to safely and repeatedly attain the necessary speeds to perform the bed-in procedure.  A controlled racetrack is the best place to perform this procedure.  AP Racing and Competition Motorsport in no way suggest or condone speeding on public roads or breaking the law in your car, nor do we take responsibility for any damage or injury that occurs as a result of using our product or these procedures.  You are performing the bed-in procedure at your own risk.  During these procedures, it’s critical that you never come to a complete stop with your foot on the brake pedal.  If you have brake ducts on your car, you may want to block them off to allow your brake system to heat up easily. The procedure outlined below is a generic procedure for most types of mild race pad.  Please check your pad manufacturer’s recommended bed-in procedure. Accelerate to approximately 60mph and then decelerate down to 5 mph.  If your car has ABS, you should try to hold the brakes at a point just before ABS intervention.  Once the car slows to 5mph, immediately accelerate back up to about 60mph, and brake again to roughly 5mph.  Repeat this series of stopping and accelerating 8 to 10 times.  Again, do not come to a complete stop with your foot on the brake pedal. Cool the brake system down by cruising at 45mph+ for 5 to 10 minutes. Visually inspect your discs.  They should be a blue/grey color (instead of shiny silver), and have an even layer of pad material across and around the entire rotor face. If the AP Racing rotors don’t have a layer of pad material on them, perform another series of stops in the manner outlined above.

AP Racing J Hook 365x30mm Replacement Brake Rotor Rings This kit is two replacement rotor discs and associated installation hardware only. Center hat is not included. Replacement discs for AP Racing 13.01.20097. Fits The Following Cars: Porsche 991 911 Carrera Porsche 991 911 S/4S/GTS Porsche 992 911 Carrera Sold/priced per pair of rotor rings (including hardware). 365x30mm (14.37" x 1.18") 72-vane, D66, J Hook Iron Racing Brake Disc Replacements AP Racing J Hook Brake Rotors – The Gold Standard in Track Day & Racing Performance Engineered for professional motorsport, HPDE, and dedicated track day use, AP Racing’s J Hook Brake Rotors deliver uncompromising performance, thermal stability, and consistent braking power. These two-piece, floating rotors are built to handle the extreme demands of road racing, with design features derived from over 50 years of elite competition—including Formula 1, NASCAR, and IMSA. Unlike conventional one-piece rotors, AP Racing’s two-piece floating design features a billet aluminum hat mated to a cast iron disc via precision-engineered bobbins. This setup allows for controlled radial expansion under high heat, minimizing distortion and coning. The result? More even pad wear, a firmer pedal feel, and longer component life, even during extended lapping sessions or endurance racing. Floating hardware includes anti-knockback spring clips that reduce piston retraction while eliminating common NVH issues like rattling. Why Choose AP Racing J Hook Rotors? Advanced Cooling, Superior Bite, Unmatched Durability At the heart of every rotor is AP Racing’s proprietary high-carbon iron alloy, developed to withstand repeated thermal cycling without cracking or warping. Internally, directional vanes—far superior to OEM pillar or straight vane designs—maximize airflow and cooling. With 60 to 84 vanes per rotor, AP Racing achieves faster heat evacuation, reduced brake fade, and a more consistent friction surface. These rotors are left/right-specific for optimal airflow and balance. The exclusive J Hook slot pattern offers enhanced initial bite and promotes uniform heat distribution across the rotor face, reducing pad deposits and vibration. Unlike drilled rotors or straight-slot competitors, the J Hook design provides cleaner pad transfer during bed-in and superior modulation under braking—ideal for serious drivers who demand feedback and control. Yes, you might hear a little more whirr, but you’ll gain the stopping power, consistency, and longevity your lap times demand. Premium Components, Affordable Performance The rotor hats are CNC-machined from 6061-T6 billet aluminum and hard anodized for strength and heat resistance. Scalloped edges under the hat further assist heat dissipation. All hardware is U.S.-made to AP Racing spec, the same quality found on pro-level racing platforms. And while these rotors are race-proven, they’re also surprisingly cost-effective to replace. Don’t settle for cheap rotors that crack after a weekend—AP’s J Hook rings offer better durability and real long-term value. Fewer replacements mean more track time, less downtime, and peace of mind knowing you're running the best. Used by Champions. Trusted by Experts. From endurance racers to HPDE enthusiasts, AP Racing brake rotors are trusted worldwide for their reliability, longevity, and performance under pressure. Whether you're shaving seconds off your lap time or building a dedicated track car, the J Hook delivers a professional-grade solution that won’t let you down. AP Racing J Hook Brake Rotors for Auto Racing, Track Days & HPDE Why Rotor Design Matters: Heat Expansion and Floating Technology As with most metals, iron brake discs expand significantly under heat. When temperatures rise, the disc grows radially—expanding in both diameter and circumference. Traditional one-piece rotors struggle to accommodate this natural expansion. As the outer edge pulls away from the center under heat stress, it creates a condition called “coning”—a distortion that compromises pad-to-rotor contact. This distortion can lead to uneven pad wear, brake tapering, and an inconsistent, long brake pedal. AP Racing two-piece floating brake rotors are purpose-built to eliminate these issues. Engineered with “float” built into the disc or hat assembly, these rotors feature oblong-shaped mounting holes that allow the hardware to slide as the disc heats up. This flexibility ensures the disc runs true within the caliper under high-temperature loads, effectively reducing distortion, minimizing pad taper and stress cracks, and promoting longer component life. Custom Mounting Hardware & Anti-Knockback Spring Clips AP Racing rotors utilize application-specific, U.S.-made mounting hardware—not generic bolts. These premium components are the exact parts used in AP’s professional motorsport products, engineered to withstand the rigors of competitive racing. To manage lateral disc motion that can push caliper pistons backward (known as knockback), AP Racing integrates anti-knockback spring clips on alternating bobbins—five on a ten-bolt setup, six on a twelve-bolt disc. These clips keep the aluminum hat and iron disc ring properly aligned while still allowing for radial float. Bonus: they eliminate annoying rattles and vibrations, ensuring a quieter, more refined braking experience. High-Performance Hat Design for Heat Isolation The disc hats in AP Racing’s two-piece floating rotors are CNC-machined from 6061-T6 billet aluminum and finished with a hard anodized coating. This high-strength aluminum alloy was selected for its ability to maintain structural integrity even at elevated temperatures. AP adds scalloped channels beneath the hat to further encourage airflow and heat evacuation from the outer disc face, minimizing thermal transfer to hubs and wheel bearings—helping reduce maintenance costs on these expensive components. Internal Vane Engineering: Airflow Optimization & Thermal Stability AP Racing’s internal vane design sets them apart from OEM and most aftermarket competitors. While many factory brake discs use non-directional pillar vanes (low-cost and NVH-focused), AP Racing rotors use directional vanes engineered for maximum airflow. These rotors are side-specific—meaning you’ll receive a unique left and right disc in each set—ensuring optimized cooling through strategic vane orientation and shape. Beyond that, AP Racing rotors feature a superior vane count, typically ranging from 60 to 84 vanes, compared to 30–48 in most aftermarket rotors. After extensive CFD and thermal analysis, this high vane count was proven to: Increase airspeed and thermal transfer Reduce recirculation and deflection at the disc face Minimize coning, cracking, and brake fade Deliver more even pad contact and extended rotor life J Hook Slot Pattern: Exclusive to AP Racing Slots and drill holes may improve initial bite, but they also introduce “cool spots” in the rotor face—areas of uneven heating that can lead to stress risers, cracks, and pad vibration. OEM rotors often avoid this by leaving the disc face blank, but that compromises bite and brake feel. AP Racing’s patented J Hook design, developed through rigorous R&D, solves this problem. The hooks are meticulously spaced around the disc’s circumference and from hat to edge, forming a continuous distortion path that ensures even heat distribution. This encourages uniform pad deposits during bed-in, helps reduce judder and cracking, and improves consistency under repeated high-load braking. In addition, the J Hook slots provide more leading edges for pads to grip than traditional curved slots or blank rotors. While this might generate a mild whirring sound during braking, the benefits—more bite, cleaner bedding, better pedal feel—make it the top choice for committed racers and serious track day drivers. Metallurgy Backed by 50+ Years of Motorsport Leadership AP Racing's reputation is built on performance, and their proprietary iron alloy used in J Hook rotors is no exception. Drawing from over five decades of elite motorsport experience, including 750+ Formula 1 wins and widespread use across NASCAR, AP’s engineers have developed a disc alloy that excels under sustained racing temperatures and stress. Where OEM discs focus on affordability and mass production, AP Racing’s J Hook rotors are purpose-built for motorsport durability and heat resistance. Affordable Replacement Cost: Serious Value for Serious Drivers Even the best brake rotors are consumables. When you drive hard—especially at the track—your discs will eventually wear out. That’s why AP Racing designed their replacement iron rings to be cost-effective, allowing you to replace worn parts without breaking the bank. Compare that to constantly buying cheap $150 rotors every weekend—rotors that can't handle the heat and need to be swapped frequently. With AP Racing’s J Hook rotors, you get longer service intervals, less downtime, and better performance over time, making them an incredibly smart long-term investment. Proven on Track. Trusted by Champions. Top-tier racing teams rely on AP Racing J Hook rotors for one reason: they perform under pressure. Whether you're running time trials, attending HPDE events, or competing in wheel-to-wheel racing, these rotors offer professional-grade reliability, safety, and performance. Bedding and Preparation of AP Racing J Hook Discs Properly preparing your new brake discs before heavy use is extremely important. The goal of bedding-in your brake pads and discs is to mate them together properly and prepare them for heavy use.  When prepared properly, or bed-in, your pads will transfer a thin layer of material to the disc face (transfer layer).  The pads in your caliper will then actually ride on that thin layer of pad material you’ve put down on the rotor, rather than rubbing directly on the iron rotor face.  A good transfer layer is going to give you superior brake pedal feel, less noise, superior pad wear, and lower the chances of cracking your discs. Important Notes- PLEASE READ! First, make sure you are on a closed course to perform a proper bed-in.  Do NOT perform the procedure on public roads.  You need a stretch of asphalt with long straights, good visibility, and no potential obstructions.  Make sure you are in a position to safely and repeatedly attain the necessary speeds to perform the bed-in procedure.  A controlled racetrack is the best place to perform this procedure.  AP Racing and Competition Motorsport in no way suggest or condone speeding on public roads or breaking the law in your car, nor do we take responsibility for any damage or injury that occurs as a result of using our product or these procedures.  You are performing the bed-in procedure at your own risk.  During these procedures, it’s critical that you never come to a complete stop with your foot on the brake pedal.  If you have brake ducts on your car, you may want to block them off to allow your brake system to heat up easily. The procedure outlined below is a generic procedure for most types of mild race pad.  Please check your pad manufacturer’s recommended bed-in procedure. Accelerate to approximately 60mph and then decelerate down to 5 mph.  If your car has ABS, you should try to hold the brakes at a point just before ABS intervention.  Once the car slows to 5mph, immediately accelerate back up to about 60mph, and brake again to roughly 5mph.  Repeat this series of stopping and accelerating 8 to 10 times.  Again, do not come to a complete stop with your foot on the brake pedal. Cool the brake system down by cruising at 45mph+ for 5 to 10 minutes. Visually inspect your discs.  They should be a blue/grey color (instead of shiny silver), and have an even layer of pad material across and around the entire rotor face. If the AP Racing rotors don’t have a layer of pad material on them, perform another series of stops in the manner outlined above.

AP Racing J Hook 372x34mm Replacement Brake Rotor Rings This kit is two replacement rotor discs and associated installation hardware only. Center hat is not included. Replacement discs for AP Racing 13.01.20182. Fits The Following Cars: Porsche 991 911 Carrera Porsche 991 911 S/4S/GTS Porsche 992 911 Carrera Sold/priced per pair of rotor rings (including hardware). 372x34mm (14.65" x 1.34") 72-vane, D66, J Hook Iron Racing Brake Disc Replacements AP Racing J Hook Brake Rotors – The Gold Standard in Track Day & Racing Performance Engineered for professional motorsport, HPDE, and dedicated track day use, AP Racing’s J Hook Brake Rotors deliver uncompromising performance, thermal stability, and consistent braking power. These two-piece, floating rotors are built to handle the extreme demands of road racing, with design features derived from over 50 years of elite competition—including Formula 1, NASCAR, and IMSA. Unlike conventional one-piece rotors, AP Racing’s two-piece floating design features a billet aluminum hat mated to a cast iron disc via precision-engineered bobbins. This setup allows for controlled radial expansion under high heat, minimizing distortion and coning. The result? More even pad wear, a firmer pedal feel, and longer component life, even during extended lapping sessions or endurance racing. Floating hardware includes anti-knockback spring clips that reduce piston retraction while eliminating common NVH issues like rattling. Why Choose AP Racing J Hook Rotors? Advanced Cooling, Superior Bite, Unmatched Durability At the heart of every rotor is AP Racing’s proprietary high-carbon iron alloy, developed to withstand repeated thermal cycling without cracking or warping. Internally, directional vanes—far superior to OEM pillar or straight vane designs—maximize airflow and cooling. With 60 to 84 vanes per rotor, AP Racing achieves faster heat evacuation, reduced brake fade, and a more consistent friction surface. These rotors are left/right-specific for optimal airflow and balance. The exclusive J Hook slot pattern offers enhanced initial bite and promotes uniform heat distribution across the rotor face, reducing pad deposits and vibration. Unlike drilled rotors or straight-slot competitors, the J Hook design provides cleaner pad transfer during bed-in and superior modulation under braking—ideal for serious drivers who demand feedback and control. Yes, you might hear a little more whirr, but you’ll gain the stopping power, consistency, and longevity your lap times demand. Premium Components, Affordable Performance The rotor hats are CNC-machined from 6061-T6 billet aluminum and hard anodized for strength and heat resistance. Scalloped edges under the hat further assist heat dissipation. All hardware is U.S.-made to AP Racing spec, the same quality found on pro-level racing platforms. And while these rotors are race-proven, they’re also surprisingly cost-effective to replace. Don’t settle for cheap rotors that crack after a weekend—AP’s J Hook rings offer better durability and real long-term value. Fewer replacements mean more track time, less downtime, and peace of mind knowing you're running the best. Used by Champions. Trusted by Experts. From endurance racers to HPDE enthusiasts, AP Racing brake rotors are trusted worldwide for their reliability, longevity, and performance under pressure. Whether you're shaving seconds off your lap time or building a dedicated track car, the J Hook delivers a professional-grade solution that won’t let you down. AP Racing J Hook Brake Rotors for Auto Racing, Track Days & HPDE Why Rotor Design Matters: Heat Expansion and Floating Technology As with most metals, iron brake discs expand significantly under heat. When temperatures rise, the disc grows radially—expanding in both diameter and circumference. Traditional one-piece rotors struggle to accommodate this natural expansion. As the outer edge pulls away from the center under heat stress, it creates a condition called “coning”—a distortion that compromises pad-to-rotor contact. This distortion can lead to uneven pad wear, brake tapering, and an inconsistent, long brake pedal. AP Racing two-piece floating brake rotors are purpose-built to eliminate these issues. Engineered with “float” built into the disc or hat assembly, these rotors feature oblong-shaped mounting holes that allow the hardware to slide as the disc heats up. This flexibility ensures the disc runs true within the caliper under high-temperature loads, effectively reducing distortion, minimizing pad taper and stress cracks, and promoting longer component life. Custom Mounting Hardware & Anti-Knockback Spring Clips AP Racing rotors utilize application-specific, U.S.-made mounting hardware—not generic bolts. These premium components are the exact parts used in AP’s professional motorsport products, engineered to withstand the rigors of competitive racing. To manage lateral disc motion that can push caliper pistons backward (known as knockback), AP Racing integrates anti-knockback spring clips on alternating bobbins—five on a ten-bolt setup, six on a twelve-bolt disc. These clips keep the aluminum hat and iron disc ring properly aligned while still allowing for radial float. Bonus: they eliminate annoying rattles and vibrations, ensuring a quieter, more refined braking experience. High-Performance Hat Design for Heat Isolation The disc hats in AP Racing’s two-piece floating rotors are CNC-machined from 6061-T6 billet aluminum and finished with a hard anodized coating. This high-strength aluminum alloy was selected for its ability to maintain structural integrity even at elevated temperatures. AP adds scalloped channels beneath the hat to further encourage airflow and heat evacuation from the outer disc face, minimizing thermal transfer to hubs and wheel bearings—helping reduce maintenance costs on these expensive components. Internal Vane Engineering: Airflow Optimization & Thermal Stability AP Racing’s internal vane design sets them apart from OEM and most aftermarket competitors. While many factory brake discs use non-directional pillar vanes (low-cost and NVH-focused), AP Racing rotors use directional vanes engineered for maximum airflow. These rotors are side-specific—meaning you’ll receive a unique left and right disc in each set—ensuring optimized cooling through strategic vane orientation and shape. Beyond that, AP Racing rotors feature a superior vane count, typically ranging from 60 to 84 vanes, compared to 30–48 in most aftermarket rotors. After extensive CFD and thermal analysis, this high vane count was proven to: Increase airspeed and thermal transfer Reduce recirculation and deflection at the disc face Minimize coning, cracking, and brake fade Deliver more even pad contact and extended rotor life J Hook Slot Pattern: Exclusive to AP Racing Slots and drill holes may improve initial bite, but they also introduce “cool spots” in the rotor face—areas of uneven heating that can lead to stress risers, cracks, and pad vibration. OEM rotors often avoid this by leaving the disc face blank, but that compromises bite and brake feel. AP Racing’s patented J Hook design, developed through rigorous R&D, solves this problem. The hooks are meticulously spaced around the disc’s circumference and from hat to edge, forming a continuous distortion path that ensures even heat distribution. This encourages uniform pad deposits during bed-in, helps reduce judder and cracking, and improves consistency under repeated high-load braking. In addition, the J Hook slots provide more leading edges for pads to grip than traditional curved slots or blank rotors. While this might generate a mild whirring sound during braking, the benefits—more bite, cleaner bedding, better pedal feel—make it the top choice for committed racers and serious track day drivers. Metallurgy Backed by 50+ Years of Motorsport Leadership AP Racing's reputation is built on performance, and their proprietary iron alloy used in J Hook rotors is no exception. Drawing from over five decades of elite motorsport experience, including 750+ Formula 1 wins and widespread use across NASCAR, AP’s engineers have developed a disc alloy that excels under sustained racing temperatures and stress. Where OEM discs focus on affordability and mass production, AP Racing’s J Hook rotors are purpose-built for motorsport durability and heat resistance. Affordable Replacement Cost: Serious Value for Serious Drivers Even the best brake rotors are consumables. When you drive hard—especially at the track—your discs will eventually wear out. That’s why AP Racing designed their replacement iron rings to be cost-effective, allowing you to replace worn parts without breaking the bank. Compare that to constantly buying cheap $150 rotors every weekend—rotors that can't handle the heat and need to be swapped frequently. With AP Racing’s J Hook rotors, you get longer service intervals, less downtime, and better performance over time, making them an incredibly smart long-term investment. Proven on Track. Trusted by Champions. Top-tier racing teams rely on AP Racing J Hook rotors for one reason: they perform under pressure. Whether you're running time trials, attending HPDE events, or competing in wheel-to-wheel racing, these rotors offer professional-grade reliability, safety, and performance. Bedding and Preparation of AP Racing J Hook Discs Properly preparing your new brake discs before heavy use is extremely important. The goal of bedding-in your brake pads and discs is to mate them together properly and prepare them for heavy use.  When prepared properly, or bed-in, your pads will transfer a thin layer of material to the disc face (transfer layer).  The pads in your caliper will then actually ride on that thin layer of pad material you’ve put down on the rotor, rather than rubbing directly on the iron rotor face.  A good transfer layer is going to give you superior brake pedal feel, less noise, superior pad wear, and lower the chances of cracking your discs. Important Notes- PLEASE READ! First, make sure you are on a closed course to perform a proper bed-in.  Do NOT perform the procedure on public roads.  You need a stretch of asphalt with long straights, good visibility, and no potential obstructions.  Make sure you are in a position to safely and repeatedly attain the necessary speeds to perform the bed-in procedure.  A controlled racetrack is the best place to perform this procedure.  AP Racing and Competition Motorsport in no way suggest or condone speeding on public roads or breaking the law in your car, nor do we take responsibility for any damage or injury that occurs as a result of using our product or these procedures.  You are performing the bed-in procedure at your own risk.  During these procedures, it’s critical that you never come to a complete stop with your foot on the brake pedal.  If you have brake ducts on your car, you may want to block them off to allow your brake system to heat up easily. The procedure outlined below is a generic procedure for most types of mild race pad.  Please check your pad manufacturer’s recommended bed-in procedure. Accelerate to approximately 60mph and then decelerate down to 5 mph.  If your car has ABS, you should try to hold the brakes at a point just before ABS intervention.  Once the car slows to 5mph, immediately accelerate back up to about 60mph, and brake again to roughly 5mph.  Repeat this series of stopping and accelerating 8 to 10 times.  Again, do not come to a complete stop with your foot on the brake pedal. Cool the brake system down by cruising at 45mph+ for 5 to 10 minutes. Visually inspect your discs.  They should be a blue/grey color (instead of shiny silver), and have an even layer of pad material across and around the entire rotor face. If the AP Racing rotors don’t have a layer of pad material on them, perform another series of stops in the manner outlined above.

AP Racing J Hook 390x36mm Replacement Brake Rotor Rings This kit is two replacement rotor discs and associated installation hardware only. Center hat is not included. Replacement discs for AP Racing 13.01.20145. Fits The Following Cars: Porsche 991 911 Carrera Porsche 991 911 S/4S/GTS Porsche 992 911 Carrera Sold/priced per pair of rotor rings (including hardware). 390x36mm (15.35" x 1.42") 72-vane, D66, J Hook Iron Racing Brake Disc Replacements AP Racing J Hook Brake Rotors – The Gold Standard in Track Day & Racing Performance Engineered for professional motorsport, HPDE, and dedicated track day use, AP Racing’s J Hook Brake Rotors deliver uncompromising performance, thermal stability, and consistent braking power. These two-piece, floating rotors are built to handle the extreme demands of road racing, with design features derived from over 50 years of elite competition—including Formula 1, NASCAR, and IMSA. Unlike conventional one-piece rotors, AP Racing’s two-piece floating design features a billet aluminum hat mated to a cast iron disc via precision-engineered bobbins. This setup allows for controlled radial expansion under high heat, minimizing distortion and coning. The result? More even pad wear, a firmer pedal feel, and longer component life, even during extended lapping sessions or endurance racing. Floating hardware includes anti-knockback spring clips that reduce piston retraction while eliminating common NVH issues like rattling. Why Choose AP Racing J Hook Rotors? Advanced Cooling, Superior Bite, Unmatched Durability At the heart of every rotor is AP Racing’s proprietary high-carbon iron alloy, developed to withstand repeated thermal cycling without cracking or warping. Internally, directional vanes—far superior to OEM pillar or straight vane designs—maximize airflow and cooling. With 60 to 84 vanes per rotor, AP Racing achieves faster heat evacuation, reduced brake fade, and a more consistent friction surface. These rotors are left/right-specific for optimal airflow and balance. The exclusive J Hook slot pattern offers enhanced initial bite and promotes uniform heat distribution across the rotor face, reducing pad deposits and vibration. Unlike drilled rotors or straight-slot competitors, the J Hook design provides cleaner pad transfer during bed-in and superior modulation under braking—ideal for serious drivers who demand feedback and control. Yes, you might hear a little more whirr, but you’ll gain the stopping power, consistency, and longevity your lap times demand. Premium Components, Affordable Performance The rotor hats are CNC-machined from 6061-T6 billet aluminum and hard anodized for strength and heat resistance. Scalloped edges under the hat further assist heat dissipation. All hardware is U.S.-made to AP Racing spec, the same quality found on pro-level racing platforms. And while these rotors are race-proven, they’re also surprisingly cost-effective to replace. Don’t settle for cheap rotors that crack after a weekend—AP’s J Hook rings offer better durability and real long-term value. Fewer replacements mean more track time, less downtime, and peace of mind knowing you're running the best. Used by Champions. Trusted by Experts. From endurance racers to HPDE enthusiasts, AP Racing brake rotors are trusted worldwide for their reliability, longevity, and performance under pressure. Whether you're shaving seconds off your lap time or building a dedicated track car, the J Hook delivers a professional-grade solution that won’t let you down. AP Racing J Hook Brake Rotors for Auto Racing, Track Days & HPDE Why Rotor Design Matters: Heat Expansion and Floating Technology As with most metals, iron brake discs expand significantly under heat. When temperatures rise, the disc grows radially—expanding in both diameter and circumference. Traditional one-piece rotors struggle to accommodate this natural expansion. As the outer edge pulls away from the center under heat stress, it creates a condition called “coning”—a distortion that compromises pad-to-rotor contact. This distortion can lead to uneven pad wear, brake tapering, and an inconsistent, long brake pedal. AP Racing two-piece floating brake rotors are purpose-built to eliminate these issues. Engineered with “float” built into the disc or hat assembly, these rotors feature oblong-shaped mounting holes that allow the hardware to slide as the disc heats up. This flexibility ensures the disc runs true within the caliper under high-temperature loads, effectively reducing distortion, minimizing pad taper and stress cracks, and promoting longer component life. Custom Mounting Hardware & Anti-Knockback Spring Clips AP Racing rotors utilize application-specific, U.S.-made mounting hardware—not generic bolts. These premium components are the exact parts used in AP’s professional motorsport products, engineered to withstand the rigors of competitive racing. To manage lateral disc motion that can push caliper pistons backward (known as knockback), AP Racing integrates anti-knockback spring clips on alternating bobbins—five on a ten-bolt setup, six on a twelve-bolt disc. These clips keep the aluminum hat and iron disc ring properly aligned while still allowing for radial float. Bonus: they eliminate annoying rattles and vibrations, ensuring a quieter, more refined braking experience. High-Performance Hat Design for Heat Isolation The disc hats in AP Racing’s two-piece floating rotors are CNC-machined from 6061-T6 billet aluminum and finished with a hard anodized coating. This high-strength aluminum alloy was selected for its ability to maintain structural integrity even at elevated temperatures. AP adds scalloped channels beneath the hat to further encourage airflow and heat evacuation from the outer disc face, minimizing thermal transfer to hubs and wheel bearings—helping reduce maintenance costs on these expensive components. Internal Vane Engineering: Airflow Optimization & Thermal Stability AP Racing’s internal vane design sets them apart from OEM and most aftermarket competitors. While many factory brake discs use non-directional pillar vanes (low-cost and NVH-focused), AP Racing rotors use directional vanes engineered for maximum airflow. These rotors are side-specific—meaning you’ll receive a unique left and right disc in each set—ensuring optimized cooling through strategic vane orientation and shape. Beyond that, AP Racing rotors feature a superior vane count, typically ranging from 60 to 84 vanes, compared to 30–48 in most aftermarket rotors. After extensive CFD and thermal analysis, this high vane count was proven to: Increase airspeed and thermal transfer Reduce recirculation and deflection at the disc face Minimize coning, cracking, and brake fade Deliver more even pad contact and extended rotor life J Hook Slot Pattern: Exclusive to AP Racing Slots and drill holes may improve initial bite, but they also introduce “cool spots” in the rotor face—areas of uneven heating that can lead to stress risers, cracks, and pad vibration. OEM rotors often avoid this by leaving the disc face blank, but that compromises bite and brake feel. AP Racing’s patented J Hook design, developed through rigorous R&D, solves this problem. The hooks are meticulously spaced around the disc’s circumference and from hat to edge, forming a continuous distortion path that ensures even heat distribution. This encourages uniform pad deposits during bed-in, helps reduce judder and cracking, and improves consistency under repeated high-load braking. In addition, the J Hook slots provide more leading edges for pads to grip than traditional curved slots or blank rotors. While this might generate a mild whirring sound during braking, the benefits—more bite, cleaner bedding, better pedal feel—make it the top choice for committed racers and serious track day drivers. Metallurgy Backed by 50+ Years of Motorsport Leadership AP Racing's reputation is built on performance, and their proprietary iron alloy used in J Hook rotors is no exception. Drawing from over five decades of elite motorsport experience, including 750+ Formula 1 wins and widespread use across NASCAR, AP’s engineers have developed a disc alloy that excels under sustained racing temperatures and stress. Where OEM discs focus on affordability and mass production, AP Racing’s J Hook rotors are purpose-built for motorsport durability and heat resistance. Affordable Replacement Cost: Serious Value for Serious Drivers Even the best brake rotors are consumables. When you drive hard—especially at the track—your discs will eventually wear out. That’s why AP Racing designed their replacement iron rings to be cost-effective, allowing you to replace worn parts without breaking the bank. Compare that to constantly buying cheap $150 rotors every weekend—rotors that can't handle the heat and need to be swapped frequently. With AP Racing’s J Hook rotors, you get longer service intervals, less downtime, and better performance over time, making them an incredibly smart long-term investment. Proven on Track. Trusted by Champions. Top-tier racing teams rely on AP Racing J Hook rotors for one reason: they perform under pressure. Whether you're running time trials, attending HPDE events, or competing in wheel-to-wheel racing, these rotors offer professional-grade reliability, safety, and performance. Bedding and Preparation of AP Racing J Hook Discs Properly preparing your new brake discs before heavy use is extremely important. The goal of bedding-in your brake pads and discs is to mate them together properly and prepare them for heavy use.  When prepared properly, or bed-in, your pads will transfer a thin layer of material to the disc face (transfer layer).  The pads in your caliper will then actually ride on that thin layer of pad material you’ve put down on the rotor, rather than rubbing directly on the iron rotor face.  A good transfer layer is going to give you superior brake pedal feel, less noise, superior pad wear, and lower the chances of cracking your discs. Important Notes- PLEASE READ! First, make sure you are on a closed course to perform a proper bed-in.  Do NOT perform the procedure on public roads.  You need a stretch of asphalt with long straights, good visibility, and no potential obstructions.  Make sure you are in a position to safely and repeatedly attain the necessary speeds to perform the bed-in procedure.  A controlled racetrack is the best place to perform this procedure.  AP Racing and Competition Motorsport in no way suggest or condone speeding on public roads or breaking the law in your car, nor do we take responsibility for any damage or injury that occurs as a result of using our product or these procedures.  You are performing the bed-in procedure at your own risk.  During these procedures, it’s critical that you never come to a complete stop with your foot on the brake pedal.  If you have brake ducts on your car, you may want to block them off to allow your brake system to heat up easily. The procedure outlined below is a generic procedure for most types of mild race pad.  Please check your pad manufacturer’s recommended bed-in procedure. Accelerate to approximately 60mph and then decelerate down to 5 mph.  If your car has ABS, you should try to hold the brakes at a point just before ABS intervention.  Once the car slows to 5mph, immediately accelerate back up to about 60mph, and brake again to roughly 5mph.  Repeat this series of stopping and accelerating 8 to 10 times.  Again, do not come to a complete stop with your foot on the brake pedal. Cool the brake system down by cruising at 45mph+ for 5 to 10 minutes. Visually inspect your discs.  They should be a blue/grey color (instead of shiny silver), and have an even layer of pad material across and around the entire rotor face. If the AP Racing rotors don’t have a layer of pad material on them, perform another series of stops in the manner outlined above.

AP Racing 380x32mm 2-piece J Hook Rear Floating Racing Brake Rotors Fit The Following Cars: Porsche 992 GT3 Cup Car (Rear) AP Racing 2-piece Competition J Hook Rear disc pair for 992 GT3 Cup Car 380mm x 32mm (14.96" x 1.26") 72 Vane, D66 Huge increase in airflow, cooling capacity, and durability vs. OEM discs Saves 2 lbs. unsprung weight per side vs. OEM iron discs Designed for: club racing, time trial, auto-x, HPDE Works with OEM calipers, no modifications required Ultralight, fully floating, anodized billet aluminum hat with float control/anti-rattle clips Sold/priced per pair. AP Racing J Hook Brake Rotors – The Gold Standard in Track Day & Racing Performance Engineered for professional motorsport, HPDE, and dedicated track day use, AP Racing’s J Hook Brake Rotors deliver uncompromising performance, thermal stability, and consistent braking power. These two-piece, floating rotors are built to handle the extreme demands of road racing, with design features derived from over 50 years of elite competition—including Formula 1, NASCAR, and IMSA. Unlike conventional one-piece rotors, AP Racing’s two-piece floating design features a billet aluminum hat mated to a cast iron disc via precision-engineered bobbins. This setup allows for controlled radial expansion under high heat, minimizing distortion and coning. The result? More even pad wear, a firmer pedal feel, and longer component life, even during extended lapping sessions or endurance racing. Floating hardware includes anti-knockback spring clips that reduce piston retraction while eliminating common NVH issues like rattling. Why Choose AP Racing J Hook Rotors? Advanced Cooling, Superior Bite, Unmatched Durability At the heart of every rotor is AP Racing’s proprietary high-carbon iron alloy, developed to withstand repeated thermal cycling without cracking or warping. Internally, directional vanes—far superior to OEM pillar or straight vane designs—maximize airflow and cooling. With 60 to 84 vanes per rotor, AP Racing achieves faster heat evacuation, reduced brake fade, and a more consistent friction surface. These rotors are left/right-specific for optimal airflow and balance. The exclusive J Hook slot pattern offers enhanced initial bite and promotes uniform heat distribution across the rotor face, reducing pad deposits and vibration. Unlike drilled rotors or straight-slot competitors, the J Hook design provides cleaner pad transfer during bed-in and superior modulation under braking—ideal for serious drivers who demand feedback and control. Yes, you might hear a little more whirr, but you’ll gain the stopping power, consistency, and longevity your lap times demand. Premium Components, Affordable Performance The rotor hats are CNC-machined from 6061-T6 billet aluminum and hard anodized for strength and heat resistance. Scalloped edges under the hat further assist heat dissipation. All hardware is U.S.-made to AP Racing spec, the same quality found on pro-level racing platforms. And while these rotors are race-proven, they’re also surprisingly cost-effective to replace. Don’t settle for cheap rotors that crack after a weekend—AP’s J Hook rings offer better durability and real long-term value. Fewer replacements mean more track time, less downtime, and peace of mind knowing you're running the best. Used by Champions. Trusted by Experts. From endurance racers to HPDE enthusiasts, AP Racing brake rotors are trusted worldwide for their reliability, longevity, and performance under pressure. Whether you're shaving seconds off your lap time or building a dedicated track car, the J Hook delivers a professional-grade solution that won’t let you down. AP Racing J Hook Brake Rotors for Auto Racing, Track Days & HPDE Why Rotor Design Matters: Heat Expansion and Floating Technology As with most metals, iron brake discs expand significantly under heat. When temperatures rise, the disc grows radially—expanding in both diameter and circumference. Traditional one-piece rotors struggle to accommodate this natural expansion. As the outer edge pulls away from the center under heat stress, it creates a condition called “coning”—a distortion that compromises pad-to-rotor contact. This distortion can lead to uneven pad wear, brake tapering, and an inconsistent, long brake pedal. AP Racing two-piece floating brake rotors are purpose-built to eliminate these issues. Engineered with “float” built into the disc or hat assembly, these rotors feature oblong-shaped mounting holes that allow the hardware to slide as the disc heats up. This flexibility ensures the disc runs true within the caliper under high-temperature loads, effectively reducing distortion, minimizing pad taper and stress cracks, and promoting longer component life. Custom Mounting Hardware & Anti-Knockback Spring Clips AP Racing rotors utilize application-specific, U.S.-made mounting hardware—not generic bolts. These premium components are the exact parts used in AP’s professional motorsport products, engineered to withstand the rigors of competitive racing. To manage lateral disc motion that can push caliper pistons backward (known as knockback), AP Racing integrates anti-knockback spring clips on alternating bobbins—five on a ten-bolt setup, six on a twelve-bolt disc. These clips keep the aluminum hat and iron disc ring properly aligned while still allowing for radial float. Bonus: they eliminate annoying rattles and vibrations, ensuring a quieter, more refined braking experience. High-Performance Hat Design for Heat Isolation The disc hats in AP Racing’s two-piece floating rotors are CNC-machined from 6061-T6 billet aluminum and finished with a hard anodized coating. This high-strength aluminum alloy was selected for its ability to maintain structural integrity even at elevated temperatures. AP adds scalloped channels beneath the hat to further encourage airflow and heat evacuation from the outer disc face, minimizing thermal transfer to hubs and wheel bearings—helping reduce maintenance costs on these expensive components. Internal Vane Engineering: Airflow Optimization & Thermal Stability AP Racing’s internal vane design sets them apart from OEM and most aftermarket competitors. While many factory brake discs use non-directional pillar vanes (low-cost and NVH-focused), AP Racing rotors use directional vanes engineered for maximum airflow. These rotors are side-specific—meaning you’ll receive a unique left and right disc in each set—ensuring optimized cooling through strategic vane orientation and shape. Beyond that, AP Racing rotors feature a superior vane count, typically ranging from 60 to 84 vanes, compared to 30–48 in most aftermarket rotors. After extensive CFD and thermal analysis, this high vane count was proven to: Increase airspeed and thermal transfer Reduce recirculation and deflection at the disc face Minimize coning, cracking, and brake fade Deliver more even pad contact and extended rotor life J Hook Slot Pattern: Exclusive to AP Racing Slots and drill holes may improve initial bite, but they also introduce “cool spots” in the rotor face—areas of uneven heating that can lead to stress risers, cracks, and pad vibration. OEM rotors often avoid this by leaving the disc face blank, but that compromises bite and brake feel. AP Racing’s patented J Hook design, developed through rigorous R&D, solves this problem. The hooks are meticulously spaced around the disc’s circumference and from hat to edge, forming a continuous distortion path that ensures even heat distribution. This encourages uniform pad deposits during bed-in, helps reduce judder and cracking, and improves consistency under repeated high-load braking. In addition, the J Hook slots provide more leading edges for pads to grip than traditional curved slots or blank rotors. While this might generate a mild whirring sound during braking, the benefits—more bite, cleaner bedding, better pedal feel—make it the top choice for committed racers and serious track day drivers. Metallurgy Backed by 50+ Years of Motorsport Leadership AP Racing's reputation is built on performance, and their proprietary iron alloy used in J Hook rotors is no exception. Drawing from over five decades of elite motorsport experience, including 750+ Formula 1 wins and widespread use across NASCAR, AP’s engineers have developed a disc alloy that excels under sustained racing temperatures and stress. Where OEM discs focus on affordability and mass production, AP Racing’s J Hook rotors are purpose-built for motorsport durability and heat resistance. Affordable Replacement Cost: Serious Value for Serious Drivers Even the best brake rotors are consumables. When you drive hard—especially at the track—your discs will eventually wear out. That’s why AP Racing designed their replacement iron rings to be cost-effective, allowing you to replace worn parts without breaking the bank. Compare that to constantly buying cheap $150 rotors every weekend—rotors that can't handle the heat and need to be swapped frequently. With AP Racing’s J Hook rotors, you get longer service intervals, less downtime, and better performance over time, making them an incredibly smart long-term investment. Proven on Track. Trusted by Champions. Top-tier racing teams rely on AP Racing J Hook rotors for one reason: they perform under pressure. Whether you're running time trials, attending HPDE events, or competing in wheel-to-wheel racing, these rotors offer professional-grade reliability, safety, and performance. Bedding and preparation of AP Racing J Hook Disc Properly preparing your new brake discs before heavy use is extremely important. The goal of bedding-in your brake pads and discs is to mate them together properly and prepare them for heavy use.  When prepared properly, or bed-in, your pads will transfer a thin layer of material to the disc face (transfer layer).  The pads in your caliper will then actually ride on that thin layer of pad material you’ve put down on the rotor, rather than rubbing directly on the iron rotor face.  A good transfer layer is going to give you superior brake pedal feel, less noise, superior pad wear, and lower the chances of cracking your discs. Important Notes- PLEASE READ! First, make sure you are on a closed course to perform a proper bed-in.  Do NOT perform the procedure on public roads.  You need a stretch of asphalt with long straights, good visibility, and no potential obstructions.  Make sure you are in a position to safely and repeatedly attain the necessary speeds to perform the bed-in procedure.  A controlled racetrack is the best place to perform this procedure.  AP Racing and Competition Motorsport in no way suggest or condone speeding on public roads or breaking the law in your car, nor do we take responsibility for any damage or injury that occurs as a result of using our product or these procedures.  You are performing the bed-in procedure at your own risk.  During these procedures, it’s critical that you never come to a complete stop with your foot on the brake pedal.  If you have brake ducts on your car, you may want to block them off to allow your brake system to heat up easily. The procedure outlined below is a generic procedure for most types of mild race pad.  Please check your pad manufacturer’s recommended bed-in procedure. Accelerate to approximately 60mph and then decelerate down to 5 mph.  If your car has ABS, you should try to hold the brakes at a point just before ABS intervention.  Once the car slows to 5mph, immediately accelerate back up to about 60mph, and brake again to roughly 5mph.  Repeat this series of stopping and accelerating 8 to 10 times.  Again, do not come to a complete stop with your foot on the brake pedal. Cool the brake system down by cruising at 45mph+ for 5 to 10 minutes. Visually inspect your discs.  They should be a blue/grey color (instead of shiny silver), and have an even layer of pad material across and around the entire rotor face. If the AP Racing rotors don’t have a layer of pad material on them, perform another series of stops in the manner outlined above.

AP Racing J Hook 380x32mm Replacement Brake Rotor Rings This kit is two replacement rotor discs and associated installation hardware only. Center hat is not included. Replacement discs for AP Racing 380mm Brake Rotors for Porsche Fits The Following Cars: Porsche 992 GT3 Cup (Front and Rear) Porsche 991 GT3 Cup (Front and Rear) Sold/priced per pair of rotor rings (including hardware). 380x32mm (14.96" x 1.25") 72-vane, D66, J Hook Iron Racing Brake Disc Replacements AP Racing J Hook Brake Rotors – The Gold Standard in Track Day & Racing Performance Engineered for professional motorsport, HPDE, and dedicated track day use, AP Racing’s J Hook Brake Rotors deliver uncompromising performance, thermal stability, and consistent braking power. These two-piece, floating rotors are built to handle the extreme demands of road racing, with design features derived from over 50 years of elite competition—including Formula 1, NASCAR, and IMSA. Unlike conventional one-piece rotors, AP Racing’s two-piece floating design features a billet aluminum hat mated to a cast iron disc via precision-engineered bobbins. This setup allows for controlled radial expansion under high heat, minimizing distortion and coning. The result? More even pad wear, a firmer pedal feel, and longer component life, even during extended lapping sessions or endurance racing. Floating hardware includes anti-knockback spring clips that reduce piston retraction while eliminating common NVH issues like rattling. Why Choose AP Racing J Hook Rotors? Advanced Cooling, Superior Bite, Unmatched Durability At the heart of every rotor is AP Racing’s proprietary high-carbon iron alloy, developed to withstand repeated thermal cycling without cracking or warping. Internally, directional vanes—far superior to OEM pillar or straight vane designs—maximize airflow and cooling. With 60 to 84 vanes per rotor, AP Racing achieves faster heat evacuation, reduced brake fade, and a more consistent friction surface. These rotors are left/right-specific for optimal airflow and balance. The exclusive J Hook slot pattern offers enhanced initial bite and promotes uniform heat distribution across the rotor face, reducing pad deposits and vibration. Unlike drilled rotors or straight-slot competitors, the J Hook design provides cleaner pad transfer during bed-in and superior modulation under braking—ideal for serious drivers who demand feedback and control. Yes, you might hear a little more whirr, but you’ll gain the stopping power, consistency, and longevity your lap times demand. Premium Components, Affordable Performance The rotor hats are CNC-machined from 6061-T6 billet aluminum and hard anodized for strength and heat resistance. Scalloped edges under the hat further assist heat dissipation. All hardware is U.S.-made to AP Racing spec, the same quality found on pro-level racing platforms. And while these rotors are race-proven, they’re also surprisingly cost-effective to replace. Don’t settle for cheap rotors that crack after a weekend—AP’s J Hook rings offer better durability and real long-term value. Fewer replacements mean more track time, less downtime, and peace of mind knowing you're running the best. Used by Champions. Trusted by Experts. From endurance racers to HPDE enthusiasts, AP Racing brake rotors are trusted worldwide for their reliability, longevity, and performance under pressure. Whether you're shaving seconds off your lap time or building a dedicated track car, the J Hook delivers a professional-grade solution that won’t let you down. AP Racing J Hook Brake Rotors for Auto Racing, Track Days & HPDE Why Rotor Design Matters: Heat Expansion and Floating Technology As with most metals, iron brake discs expand significantly under heat. When temperatures rise, the disc grows radially—expanding in both diameter and circumference. Traditional one-piece rotors struggle to accommodate this natural expansion. As the outer edge pulls away from the center under heat stress, it creates a condition called “coning”—a distortion that compromises pad-to-rotor contact. This distortion can lead to uneven pad wear, brake tapering, and an inconsistent, long brake pedal. AP Racing two-piece floating brake rotors are purpose-built to eliminate these issues. Engineered with “float” built into the disc or hat assembly, these rotors feature oblong-shaped mounting holes that allow the hardware to slide as the disc heats up. This flexibility ensures the disc runs true within the caliper under high-temperature loads, effectively reducing distortion, minimizing pad taper and stress cracks, and promoting longer component life. Custom Mounting Hardware & Anti-Knockback Spring Clips AP Racing rotors utilize application-specific, U.S.-made mounting hardware—not generic bolts. These premium components are the exact parts used in AP’s professional motorsport products, engineered to withstand the rigors of competitive racing. To manage lateral disc motion that can push caliper pistons backward (known as knockback), AP Racing integrates anti-knockback spring clips on alternating bobbins—five on a ten-bolt setup, six on a twelve-bolt disc. These clips keep the aluminum hat and iron disc ring properly aligned while still allowing for radial float. Bonus: they eliminate annoying rattles and vibrations, ensuring a quieter, more refined braking experience. High-Performance Hat Design for Heat Isolation The disc hats in AP Racing’s two-piece floating rotors are CNC-machined from 6061-T6 billet aluminum and finished with a hard anodized coating. This high-strength aluminum alloy was selected for its ability to maintain structural integrity even at elevated temperatures. AP adds scalloped channels beneath the hat to further encourage airflow and heat evacuation from the outer disc face, minimizing thermal transfer to hubs and wheel bearings—helping reduce maintenance costs on these expensive components. Internal Vane Engineering: Airflow Optimization & Thermal Stability AP Racing’s internal vane design sets them apart from OEM and most aftermarket competitors. While many factory brake discs use non-directional pillar vanes (low-cost and NVH-focused), AP Racing rotors use directional vanes engineered for maximum airflow. These rotors are side-specific—meaning you’ll receive a unique left and right disc in each set—ensuring optimized cooling through strategic vane orientation and shape. Beyond that, AP Racing rotors feature a superior vane count, typically ranging from 60 to 84 vanes, compared to 30–48 in most aftermarket rotors. After extensive CFD and thermal analysis, this high vane count was proven to: Increase airspeed and thermal transfer Reduce recirculation and deflection at the disc face Minimize coning, cracking, and brake fade Deliver more even pad contact and extended rotor life J Hook Slot Pattern: Exclusive to AP Racing Slots and drill holes may improve initial bite, but they also introduce “cool spots” in the rotor face—areas of uneven heating that can lead to stress risers, cracks, and pad vibration. OEM rotors often avoid this by leaving the disc face blank, but that compromises bite and brake feel. AP Racing’s patented J Hook design, developed through rigorous R&D, solves this problem. The hooks are meticulously spaced around the disc’s circumference and from hat to edge, forming a continuous distortion path that ensures even heat distribution. This encourages uniform pad deposits during bed-in, helps reduce judder and cracking, and improves consistency under repeated high-load braking. In addition, the J Hook slots provide more leading edges for pads to grip than traditional curved slots or blank rotors. While this might generate a mild whirring sound during braking, the benefits—more bite, cleaner bedding, better pedal feel—make it the top choice for committed racers and serious track day drivers. Metallurgy Backed by 50+ Years of Motorsport Leadership AP Racing's reputation is built on performance, and their proprietary iron alloy used in J Hook rotors is no exception. Drawing from over five decades of elite motorsport experience, including 750+ Formula 1 wins and widespread use across NASCAR, AP’s engineers have developed a disc alloy that excels under sustained racing temperatures and stress. Where OEM discs focus on affordability and mass production, AP Racing’s J Hook rotors are purpose-built for motorsport durability and heat resistance. Affordable Replacement Cost: Serious Value for Serious Drivers Even the best brake rotors are consumables. When you drive hard—especially at the track—your discs will eventually wear out. That’s why AP Racing designed their replacement iron rings to be cost-effective, allowing you to replace worn parts without breaking the bank. Compare that to constantly buying cheap $150 rotors every weekend—rotors that can't handle the heat and need to be swapped frequently. With AP Racing’s J Hook rotors, you get longer service intervals, less downtime, and better performance over time, making them an incredibly smart long-term investment. Proven on Track. Trusted by Champions. Top-tier racing teams rely on AP Racing J Hook rotors for one reason: they perform under pressure. Whether you're running time trials, attending HPDE events, or competing in wheel-to-wheel racing, these rotors offer professional-grade reliability, safety, and performance. Bedding and Preparation of AP Racing J Hook Discs Properly preparing your new brake discs before heavy use is extremely important. The goal of bedding-in your brake pads and discs is to mate them together properly and prepare them for heavy use.  When prepared properly, or bed-in, your pads will transfer a thin layer of material to the disc face (transfer layer).  The pads in your caliper will then actually ride on that thin layer of pad material you’ve put down on the rotor, rather than rubbing directly on the iron rotor face.  A good transfer layer is going to give you superior brake pedal feel, less noise, superior pad wear, and lower the chances of cracking your discs. Important Notes- PLEASE READ! First, make sure you are on a closed course to perform a proper bed-in.  Do NOT perform the procedure on public roads.  You need a stretch of asphalt with long straights, good visibility, and no potential obstructions.  Make sure you are in a position to safely and repeatedly attain the necessary speeds to perform the bed-in procedure.  A controlled racetrack is the best place to perform this procedure.  AP Racing and Competition Motorsport in no way suggest or condone speeding on public roads or breaking the law in your car, nor do we take responsibility for any damage or injury that occurs as a result of using our product or these procedures.  You are performing the bed-in procedure at your own risk.  During these procedures, it’s critical that you never come to a complete stop with your foot on the brake pedal.  If you have brake ducts on your car, you may want to block them off to allow your brake system to heat up easily. The procedure outlined below is a generic procedure for most types of mild race pad.  Please check your pad manufacturer’s recommended bed-in procedure. Accelerate to approximately 60mph and then decelerate down to 5 mph.  If your car has ABS, you should try to hold the brakes at a point just before ABS intervention.  Once the car slows to 5mph, immediately accelerate back up to about 60mph, and brake again to roughly 5mph.  Repeat this series of stopping and accelerating 8 to 10 times.  Again, do not come to a complete stop with your foot on the brake pedal. Cool the brake system down by cruising at 45mph+ for 5 to 10 minutes. Visually inspect your discs.  They should be a blue/grey color (instead of shiny silver), and have an even layer of pad material across and around the entire rotor face. If the AP Racing rotors don’t have a layer of pad material on them, perform another series of stops in the manner outlined above.

AP Racing 380x32mm 2-piece J Hook Front Floating Racing Brake Rotors Fit The Following Cars (w/ OEM Iron Rotors) Porsche 992 GT3 Cup Car (Front) AP Racing by Essex 2-piece Competition J Hook front disc pair for 992 GT3 Cup Car 380mm x 32mm (14.96" x 1.26") 72 Vane, D66 Huge increase in airflow, cooling capacity, and durability vs. OEM discs Saves 2 lbs. unsprung weight per side vs. OEM iron discs Designed for: club racing, time trial, auto-x, HPDE Works with OEM calipers, no modifications required Ultralight, fully floating, anodized billet aluminum hat with float control/anti-rattle clips Sold/priced per pair. AP Racing J Hook Brake Rotors – The Gold Standard in Track Day & Racing Performance Engineered for professional motorsport, HPDE, and dedicated track day use, AP Racing’s J Hook Brake Rotors deliver uncompromising performance, thermal stability, and consistent braking power. These two-piece, floating rotors are built to handle the extreme demands of road racing, with design features derived from over 50 years of elite competition—including Formula 1, NASCAR, and IMSA. Unlike conventional one-piece rotors, AP Racing’s two-piece floating design features a billet aluminum hat mated to a cast iron disc via precision-engineered bobbins. This setup allows for controlled radial expansion under high heat, minimizing distortion and coning. The result? More even pad wear, a firmer pedal feel, and longer component life, even during extended lapping sessions or endurance racing. Floating hardware includes anti-knockback spring clips that reduce piston retraction while eliminating common NVH issues like rattling. Why Choose AP Racing J Hook Rotors? Advanced Cooling, Superior Bite, Unmatched Durability At the heart of every rotor is AP Racing’s proprietary high-carbon iron alloy, developed to withstand repeated thermal cycling without cracking or warping. Internally, directional vanes—far superior to OEM pillar or straight vane designs—maximize airflow and cooling. With 60 to 84 vanes per rotor, AP Racing achieves faster heat evacuation, reduced brake fade, and a more consistent friction surface. These rotors are left/right-specific for optimal airflow and balance. The exclusive J Hook slot pattern offers enhanced initial bite and promotes uniform heat distribution across the rotor face, reducing pad deposits and vibration. Unlike drilled rotors or straight-slot competitors, the J Hook design provides cleaner pad transfer during bed-in and superior modulation under braking—ideal for serious drivers who demand feedback and control. Yes, you might hear a little more whirr, but you’ll gain the stopping power, consistency, and longevity your lap times demand. Premium Components, Affordable Performance The rotor hats are CNC-machined from 6061-T6 billet aluminum and hard anodized for strength and heat resistance. Scalloped edges under the hat further assist heat dissipation. All hardware is U.S.-made to AP Racing spec, the same quality found on pro-level racing platforms. And while these rotors are race-proven, they’re also surprisingly cost-effective to replace. Don’t settle for cheap rotors that crack after a weekend—AP’s J Hook rings offer better durability and real long-term value. Fewer replacements mean more track time, less downtime, and peace of mind knowing you're running the best. Used by Champions. Trusted by Experts. From endurance racers to HPDE enthusiasts, AP Racing brake rotors are trusted worldwide for their reliability, longevity, and performance under pressure. Whether you're shaving seconds off your lap time or building a dedicated track car, the J Hook delivers a professional-grade solution that won’t let you down.   AP Racing J Hook Brake Rotors for Auto Racing, Track Days & HPDE Why Rotor Design Matters: Heat Expansion and Floating Technology As with most metals, iron brake discs expand significantly under heat. When temperatures rise, the disc grows radially—expanding in both diameter and circumference. Traditional one-piece rotors struggle to accommodate this natural expansion. As the outer edge pulls away from the center under heat stress, it creates a condition called “coning”—a distortion that compromises pad-to-rotor contact. This distortion can lead to uneven pad wear, brake tapering, and an inconsistent, long brake pedal. AP Racing two-piece floating brake rotors are purpose-built to eliminate these issues. Engineered with “float” built into the disc or hat assembly, these rotors feature oblong-shaped mounting holes that allow the hardware to slide as the disc heats up. This flexibility ensures the disc runs true within the caliper under high-temperature loads, effectively reducing distortion, minimizing pad taper and stress cracks, and promoting longer component life. Custom Mounting Hardware & Anti-Knockback Spring Clips AP Racing rotors utilize application-specific, U.S.-made mounting hardware—not generic bolts. These premium components are the exact parts used in AP’s professional motorsport products, engineered to withstand the rigors of competitive racing. To manage lateral disc motion that can push caliper pistons backward (known as knockback), AP Racing integrates anti-knockback spring clips on alternating bobbins—five on a ten-bolt setup, six on a twelve-bolt disc. These clips keep the aluminum hat and iron disc ring properly aligned while still allowing for radial float. Bonus: they eliminate annoying rattles and vibrations, ensuring a quieter, more refined braking experience. High-Performance Hat Design for Heat Isolation The disc hats in AP Racing’s two-piece floating rotors are CNC-machined from 6061-T6 billet aluminum and finished with a hard anodized coating. This high-strength aluminum alloy was selected for its ability to maintain structural integrity even at elevated temperatures. AP adds scalloped channels beneath the hat to further encourage airflow and heat evacuation from the outer disc face, minimizing thermal transfer to hubs and wheel bearings—helping reduce maintenance costs on these expensive components. Internal Vane Engineering: Airflow Optimization & Thermal Stability AP Racing’s internal vane design sets them apart from OEM and most aftermarket competitors. While many factory brake discs use non-directional pillar vanes (low-cost and NVH-focused), AP Racing rotors use directional vanes engineered for maximum airflow. These rotors are side-specific—meaning you’ll receive a unique left and right disc in each set—ensuring optimized cooling through strategic vane orientation and shape. Beyond that, AP Racing rotors feature a superior vane count, typically ranging from 60 to 84 vanes, compared to 30–48 in most aftermarket rotors. After extensive CFD and thermal analysis, this high vane count was proven to: Increase airspeed and thermal transfer Reduce recirculation and deflection at the disc face Minimize coning, cracking, and brake fade Deliver more even pad contact and extended rotor life J Hook Slot Pattern: Exclusive to AP Racing Slots and drill holes may improve initial bite, but they also introduce “cool spots” in the rotor face—areas of uneven heating that can lead to stress risers, cracks, and pad vibration. OEM rotors often avoid this by leaving the disc face blank, but that compromises bite and brake feel. AP Racing’s patented J Hook design, developed through rigorous R&D, solves this problem. The hooks are meticulously spaced around the disc’s circumference and from hat to edge, forming a continuous distortion path that ensures even heat distribution. This encourages uniform pad deposits during bed-in, helps reduce judder and cracking, and improves consistency under repeated high-load braking. In addition, the J Hook slots provide more leading edges for pads to grip than traditional curved slots or blank rotors. While this might generate a mild whirring sound during braking, the benefits—more bite, cleaner bedding, better pedal feel—make it the top choice for committed racers and serious track day drivers. Metallurgy Backed by 50+ Years of Motorsport Leadership AP Racing's reputation is built on performance, and their proprietary iron alloy used in J Hook rotors is no exception. Drawing from over five decades of elite motorsport experience, including 750+ Formula 1 wins and widespread use across NASCAR, AP’s engineers have developed a disc alloy that excels under sustained racing temperatures and stress. Where OEM discs focus on affordability and mass production, AP Racing’s J Hook rotors are purpose-built for motorsport durability and heat resistance. Affordable Replacement Cost: Serious Value for Serious Drivers Even the best brake rotors are consumables. When you drive hard—especially at the track—your discs will eventually wear out. That’s why AP Racing designed their replacement iron rings to be cost-effective, allowing you to replace worn parts without breaking the bank. Compare that to constantly buying cheap $150 rotors every weekend—rotors that can't handle the heat and need to be swapped frequently. With AP Racing’s J Hook rotors, you get longer service intervals, less downtime, and better performance over time, making them an incredibly smart long-term investment. Proven on Track. Trusted by Champions. Top-tier racing teams rely on AP Racing J Hook rotors for one reason: they perform under pressure. Whether you're running time trials, attending HPDE events, or competing in wheel-to-wheel racing, these rotors offer professional-grade reliability, safety, and performance. Bedding and preparation of AP Racing J Hook Disc Properly preparing your new brake discs before heavy use is extremely important. The goal of bedding-in your brake pads and discs is to mate them together properly and prepare them for heavy use.  When prepared properly, or bed-in, your pads will transfer a thin layer of material to the disc face (transfer layer).  The pads in your caliper will then actually ride on that thin layer of pad material you’ve put down on the rotor, rather than rubbing directly on the iron rotor face.  A good transfer layer is going to give you superior brake pedal feel, less noise, superior pad wear, and lower the chances of cracking your discs. Important Notes- PLEASE READ! First, make sure you are on a closed course to perform a proper bed-in.  Do NOT perform the procedure on public roads.  You need a stretch of asphalt with long straights, good visibility, and no potential obstructions.  Make sure you are in a position to safely and repeatedly attain the necessary speeds to perform the bed-in procedure.  A controlled racetrack is the best place to perform this procedure.  AP Racing and Competition Motorsport in no way suggest or condone speeding on public roads or breaking the law in your car, nor do we take responsibility for any damage or injury that occurs as a result of using our product or these procedures.  You are performing the bed-in procedure at your own risk.  During these procedures, it’s critical that you never come to a complete stop with your foot on the brake pedal.  If you have brake ducts on your car, you may want to block them off to allow your brake system to heat up easily. The procedure outlined below is a generic procedure for most types of mild race pad.  Please check your pad manufacturer’s recommended bed-in procedure. Accelerate to approximately 60mph and then decelerate down to 5 mph.  If your car has ABS, you should try to hold the brakes at a point just before ABS intervention.  Once the car slows to 5mph, immediately accelerate back up to about 60mph, and brake again to roughly 5mph.  Repeat this series of stopping and accelerating 8 to 10 times.  Again, do not come to a complete stop with your foot on the brake pedal. Cool the brake system down by cruising at 45mph+ for 5 to 10 minutes. Visually inspect your discs.  They should be a blue/grey color (instead of shiny silver), and have an even layer of pad material across and around the entire rotor face. If the AP Racing rotors don’t have a layer of pad material on them, perform another series of stops in the manner outlined above.

Brembo 330x34mm 2-piece Front Floating Racing Brake Rotors Fit The Following Cars (w/ OEM Iron Rotors) Porsche 992 911 Carrera (Front) Brembo 2-piece Competition cross-drilled front disc pair for iron discs 330mm x 34mm (12.99" x 1.34") 72 Vane, D66 Huge increase in airflow, cooling capacity, and durability vs. OEM discs Saves 2 lbs. unsprung weight per side vs. OEM iron discs Designed for: club racing, time trial, auto-x, HPDE Works with OEM calipers, no modifications required Ultralight, fully floating, anodized billet aluminum hat with float control/anti-rattle clips Sold/priced per pair. Brembo 2-Piece Rotor FAQs How long do Brembo discs last? The usable life of a brake disc is influenced by a number of factors including vehicle weight, driving style, vehicle usage, brake pad material, and many others. Therefore a blanket disc lifetime cannot be given. However, when used in the same conditions, a Brembo disc should meet or exceed the life of the disc it replaces. It is important to periodically check the disc thickness, and replace the disc if it falls below the minimum allowed thickness. How does reducing weight of the braking system benefit the vehicle? The mass of any vehicle requires energy to accelerate or decelerate. Reducing vehicle mass improves acceleration and requires less energy to be dissipated during deceleration. Rotating mass requires additional energy in order to increase or decrease its speed of rotation. Therefore, decreasing the mass of the caliper is valuable due to its contribution to total vehicle mass. Decreasing the mass of the disc has an even greater benefit due to the fact that the disc must rotate as well. Additionally, the mass of the brake system is also unsprung mass. Reducing the unsprung mass has the additional benefit of improved suspension performance, resulting in enhanced ride and handling. Should new discs and pads be bedded in? The bedding procedure is an important step when installing new rotors and pads. Correctly bedded pads form a transfer layer of material on the surface of the disc which improves overall "bite" and performance. Without proper "pre-bedding" that simulates the correct heat and torque loads seen in actual driving conditions, a pad's true potential cannot be realized. This process will also ensure that the pads will produce a rotor finish with a consistent transfer layer which prevents "judder" from occurring. The Brembo Bedding Memo should be followed when installing a new Brembo system or new discs and / or street pads. For race friction and / or track use, please contact us for detailed information regarding the appropriate bedding procedure to follow. Some of the bushings in the two-piece disc assembly seem to be loose. The two-piece disc assemblies utilize a floating disc. The mounting system of the disc is designed to allow a specific amount of float in both the radial and axial directions. Brembo has engineered special springs that are used on every other fastener in order to slightly preload the assembly. This has been done to prevent excessive noise from the system during street use, while still maintaining the benefits of a floating disc. These springs can be seen when looking at the backside of the disc. The small screws on the backside of the disc are properly torqued during assembly and utilize thread lock compound to prevent loosening. They must not be tightened further. What is the difference between the systems Brembo offers? Brembo offers different levels for different applications, and for different budgets. There are currently three performance levels within the Brembo program. The first level is the Sport system. These kits include cross-drilled or slotted discs and high performance brake pads, and are direct replacements for the OEM components. The second level, the Gran Turismo system, upgrades the entire corner brake assembly. These kits combine fixed mount, 4, 6, or 8-piston aluminum calipers equipped with high performance brake pads, one or two piece directionally vented discs, and steel-braided brake lines. For those seeking a system for exclusive or nearly exclusive track use, the Race systems offer upgrades consisting of true racing components. Why are there so many holes in a cross-drilled disc? The number of holes in a cross-drilled disc is part of the engineered system. Brembo has done extensive testing with regards to the number of holes, their size, their location and their chamfering. This attention to detail is what truly sets Brembo apart in the world of braking. The same attention to detail that is delivered to the Ferrari Formula One effort is a component of the high performance program. The number of holes in a disc is in part a function of the size of the disc and the internal venting (if it is a vented disc). Why use a two-piece "floating" disc assembly? There are several reasons that a two-piece floating disc assembly is of benefit. First, by using an aluminum bell for the hub section of the disc saves a great deal of weight. Since this is both rotating and unsprung, it benefits the acceleration, braking, and handling of the vehicle. Secondly, it is better able to handle the large temperature changes that a brake disc experiences. In a two-piece floating disc assembly, the iron disc heats up uniformly, and the controlled float which is present allows for the differential expansion of the very hot brake disc, and the relatively cool aluminum bell. This allows the disc to be used under severe conditions without having a detrimental effect. Will a Brembo brake system work with my standard master cylinder, ABS, or traction control? Brembo brake systems are designed to work with your standard master cylinder, and do not hamper the function of your ABS or traction control system. Will I experience brake noise with Brembo brakes? Brembo makes every effort to test for and eliminate abnormal brake noise from the systems we offer. There are many factors that can contribute to abnormal brake noises, and while it is unlikely that a Brembo system will create noise, the engineering and customer service departments are available to answer questions and work to solve any noise issues which may arise. Please contact us if you have additional questions or concerns. How do I properly bed my new Brembo brake rotors? It is important to follow the proper brake bedding procedure following installation. This is necessary not only for optimum performance of the system, but also to avoid onset of judder (vibration felt through brake and steering).   The discs are delivered with a thin zinc coating to prevent corrosion. Prior to beginning the bedding procedure, this plating must be removed from the braking surfaces by driving the car slowly (under 30mph) and performing very light brake applications in order to remove the plating without generating heat. With too much heat or pedal pressure, this plating can be deposited unevenly on the disc, and impregnated into the pad, further increasing the likelihood of judder development. Once a visual inspection of the braking surfaces confirms that the plating has been evenly removed, begin with the bedding procedure as specified below. Drive vehicle to a remote area and perform at least 30 brake applications of 3 second duration. Use light/medium deceleration with varying starting speeds. Leave at least ½ mile between each brake application The purpose of this procedure is to gradually increase the temperature in the components without thermal shock, and to mate the brake pad and disc friction surfaces  After the repeated stops, drive the vehicle for several miles with little or no braking in order to adequately cool the components  The system is now ready for normal use  This entire procedure must be complete before driving the vehicle as normal. It is especially important that this process is completed before any extended same-speed driving is done (i.e. freeway travel). Failure to follow these instructions greatly increases the likelihood of judder development

AP Racing 350x28mm 2-piece J Hook Rear Floating Racing Brake Rotors Fit The Following Cars (w/ OEM Iron Rotors) Porsche 992 S/4S/GTS  AP Racing 2-piece Competition J Hook front disc pair for  with iron discs 350mm x 28mm (13.78" x 1.10") 72 Vane, D66 Huge increase in airflow, cooling capacity, and durability vs. OEM discs Saves 2 lbs. unsprung weight per side vs. OEM iron discs Designed for: club racing, time trial, auto-x, HPDE Works with OEM calipers, no modifications required Ultralight, fully floating, anodized billet aluminum hat with float control/anti-rattle clips Sold/priced per pair. AP Racing J Hook Brake Rotors – The Gold Standard in Track Day & Racing Performance Engineered for professional motorsport, HPDE, and dedicated track day use, AP Racing’s J Hook Brake Rotors deliver uncompromising performance, thermal stability, and consistent braking power. These two-piece, floating rotors are built to handle the extreme demands of road racing, with design features derived from over 50 years of elite competition—including Formula 1, NASCAR, and IMSA. Unlike conventional one-piece rotors, AP Racing’s two-piece floating design features a billet aluminum hat mated to a cast iron disc via precision-engineered bobbins. This setup allows for controlled radial expansion under high heat, minimizing distortion and coning. The result? More even pad wear, a firmer pedal feel, and longer component life, even during extended lapping sessions or endurance racing. Floating hardware includes anti-knockback spring clips that reduce piston retraction while eliminating common NVH issues like rattling. Why Choose AP Racing J Hook Rotors? Advanced Cooling, Superior Bite, Unmatched Durability At the heart of every rotor is AP Racing’s proprietary high-carbon iron alloy, developed to withstand repeated thermal cycling without cracking or warping. Internally, directional vanes—far superior to OEM pillar or straight vane designs—maximize airflow and cooling. With 60 to 84 vanes per rotor, AP Racing achieves faster heat evacuation, reduced brake fade, and a more consistent friction surface. These rotors are left/right-specific for optimal airflow and balance. The exclusive J Hook slot pattern offers enhanced initial bite and promotes uniform heat distribution across the rotor face, reducing pad deposits and vibration. Unlike drilled rotors or straight-slot competitors, the J Hook design provides cleaner pad transfer during bed-in and superior modulation under braking—ideal for serious drivers who demand feedback and control. Yes, you might hear a little more whirr, but you’ll gain the stopping power, consistency, and longevity your lap times demand. Premium Components, Affordable Performance The rotor hats are CNC-machined from 6061-T6 billet aluminum and hard anodized for strength and heat resistance. Scalloped edges under the hat further assist heat dissipation. All hardware is U.S.-made to AP Racing spec, the same quality found on pro-level racing platforms. And while these rotors are race-proven, they’re also surprisingly cost-effective to replace. Don’t settle for cheap rotors that crack after a weekend—AP’s J Hook rings offer better durability and real long-term value. Fewer replacements mean more track time, less downtime, and peace of mind knowing you're running the best. Used by Champions. Trusted by Experts. From endurance racers to HPDE enthusiasts, AP Racing brake rotors are trusted worldwide for their reliability, longevity, and performance under pressure. Whether you're shaving seconds off your lap time or building a dedicated track car, the J Hook delivers a professional-grade solution that won’t let you down.   AP Racing J Hook Brake Rotors for Auto Racing, Track Days & HPDE Why Rotor Design Matters: Heat Expansion and Floating Technology As with most metals, iron brake discs expand significantly under heat. When temperatures rise, the disc grows radially—expanding in both diameter and circumference. Traditional one-piece rotors struggle to accommodate this natural expansion. As the outer edge pulls away from the center under heat stress, it creates a condition called “coning”—a distortion that compromises pad-to-rotor contact. This distortion can lead to uneven pad wear, brake tapering, and an inconsistent, long brake pedal. AP Racing two-piece floating brake rotors are purpose-built to eliminate these issues. Engineered with “float” built into the disc or hat assembly, these rotors feature oblong-shaped mounting holes that allow the hardware to slide as the disc heats up. This flexibility ensures the disc runs true within the caliper under high-temperature loads, effectively reducing distortion, minimizing pad taper and stress cracks, and promoting longer component life. Custom Mounting Hardware & Anti-Knockback Spring Clips AP Racing rotors utilize application-specific, U.S.-made mounting hardware—not generic bolts. These premium components are the exact parts used in AP’s professional motorsport products, engineered to withstand the rigors of competitive racing. To manage lateral disc motion that can push caliper pistons backward (known as knockback), AP Racing integrates anti-knockback spring clips on alternating bobbins—five on a ten-bolt setup, six on a twelve-bolt disc. These clips keep the aluminum hat and iron disc ring properly aligned while still allowing for radial float. Bonus: they eliminate annoying rattles and vibrations, ensuring a quieter, more refined braking experience. High-Performance Hat Design for Heat Isolation The disc hats in AP Racing’s two-piece floating rotors are CNC-machined from 6061-T6 billet aluminum and finished with a hard anodized coating. This high-strength aluminum alloy was selected for its ability to maintain structural integrity even at elevated temperatures. AP adds scalloped channels beneath the hat to further encourage airflow and heat evacuation from the outer disc face, minimizing thermal transfer to hubs and wheel bearings—helping reduce maintenance costs on these expensive components. Internal Vane Engineering: Airflow Optimization & Thermal Stability AP Racing’s internal vane design sets them apart from OEM and most aftermarket competitors. While many factory brake discs use non-directional pillar vanes (low-cost and NVH-focused), AP Racing rotors use directional vanes engineered for maximum airflow. These rotors are side-specific—meaning you’ll receive a unique left and right disc in each set—ensuring optimized cooling through strategic vane orientation and shape. Beyond that, AP Racing rotors feature a superior vane count, typically ranging from 60 to 84 vanes, compared to 30–48 in most aftermarket rotors. After extensive CFD and thermal analysis, this high vane count was proven to: Increase airspeed and thermal transfer Reduce recirculation and deflection at the disc face Minimize coning, cracking, and brake fade Deliver more even pad contact and extended rotor life J Hook Slot Pattern: Exclusive to AP Racing Slots and drill holes may improve initial bite, but they also introduce “cool spots” in the rotor face—areas of uneven heating that can lead to stress risers, cracks, and pad vibration. OEM rotors often avoid this by leaving the disc face blank, but that compromises bite and brake feel. AP Racing’s patented J Hook design, developed through rigorous R&D, solves this problem. The hooks are meticulously spaced around the disc’s circumference and from hat to edge, forming a continuous distortion path that ensures even heat distribution. This encourages uniform pad deposits during bed-in, helps reduce judder and cracking, and improves consistency under repeated high-load braking. In addition, the J Hook slots provide more leading edges for pads to grip than traditional curved slots or blank rotors. While this might generate a mild whirring sound during braking, the benefits—more bite, cleaner bedding, better pedal feel—make it the top choice for committed racers and serious track day drivers. Metallurgy Backed by 50+ Years of Motorsport Leadership AP Racing's reputation is built on performance, and their proprietary iron alloy used in J Hook rotors is no exception. Drawing from over five decades of elite motorsport experience, including 750+ Formula 1 wins and widespread use across NASCAR, AP’s engineers have developed a disc alloy that excels under sustained racing temperatures and stress. Where OEM discs focus on affordability and mass production, AP Racing’s J Hook rotors are purpose-built for motorsport durability and heat resistance. Affordable Replacement Cost: Serious Value for Serious Drivers Even the best brake rotors are consumables. When you drive hard—especially at the track—your discs will eventually wear out. That’s why AP Racing designed their replacement iron rings to be cost-effective, allowing you to replace worn parts without breaking the bank. Compare that to constantly buying cheap $150 rotors every weekend—rotors that can't handle the heat and need to be swapped frequently. With AP Racing’s J Hook rotors, you get longer service intervals, less downtime, and better performance over time, making them an incredibly smart long-term investment. Proven on Track. Trusted by Champions. Top-tier racing teams rely on AP Racing J Hook rotors for one reason: they perform under pressure. Whether you're running time trials, attending HPDE events, or competing in wheel-to-wheel racing, these rotors offer professional-grade reliability, safety, and performance. Bedding and preparation of AP Racing J Hook Disc Properly preparing your new brake discs before heavy use is extremely important. The goal of bedding-in your brake pads and discs is to mate them together properly and prepare them for heavy use.  When prepared properly, or bed-in, your pads will transfer a thin layer of material to the disc face (transfer layer).  The pads in your caliper will then actually ride on that thin layer of pad material you’ve put down on the rotor, rather than rubbing directly on the iron rotor face.  A good transfer layer is going to give you superior brake pedal feel, less noise, superior pad wear, and lower the chances of cracking your discs. Important Notes- PLEASE READ! First, make sure you are on a closed course to perform a proper bed-in.  Do NOT perform the procedure on public roads.  You need a stretch of asphalt with long straights, good visibility, and no potential obstructions.  Make sure you are in a position to safely and repeatedly attain the necessary speeds to perform the bed-in procedure.  A controlled racetrack is the best place to perform this procedure.  AP Racing and Competition Motorsport in no way suggest or condone speeding on public roads or breaking the law in your car, nor do we take responsibility for any damage or injury that occurs as a result of using our product or these procedures.  You are performing the bed-in procedure at your own risk.  During these procedures, it’s critical that you never come to a complete stop with your foot on the brake pedal.  If you have brake ducts on your car, you may want to block them off to allow your brake system to heat up easily. The procedure outlined below is a generic procedure for most types of mild race pad.  Please check your pad manufacturer’s recommended bed-in procedure. Accelerate to approximately 60mph and then decelerate down to 5 mph.  If your car has ABS, you should try to hold the brakes at a point just before ABS intervention.  Once the car slows to 5mph, immediately accelerate back up to about 60mph, and brake again to roughly 5mph.  Repeat this series of stopping and accelerating 8 to 10 times.  Again, do not come to a complete stop with your foot on the brake pedal. Cool the brake system down by cruising at 45mph+ for 5 to 10 minutes. Visually inspect your discs.  They should be a blue/grey color (instead of shiny silver), and have an even layer of pad material across and around the entire rotor face. If the AP Racing rotors don’t have a layer of pad material on them, perform another series of stops in the manner outlined above.

Girodisc Porsche 997 GT3 Front Rings Maintain your Porsche’s legendary braking precision with Girodisc D1-127 380mm front replacement rings. Designed as direct replacements for Girodisc’s two-piece systems, these high-performance rings bolt to your existing aluminum hats using the included floating hardware kit. Each rotor is machined from Girodisc’s proprietary high-carbon cast iron for superior heat management, consistent friction, and fade-free performance in both street and track environments. Vehicle Fitment Compatible with:• Porsche 997 GT3 (2006–2011)• Porsche 997 GT3 RS (2007–2011)• Porsche 997.2 GT3 and GT3 RS (380mm front rotors)Note: Designed for Girodisc 380mm two-piece front rotor systems. Not compatible with OEM PCCB carbon-ceramic rotors or one-piece iron discs. Features • Sold as a left/right pair with complete floating hardware kit• Direct replacements for Girodisc 380mm two-piece front rotors• CNC-machined from high-carbon iron alloy for maximum thermal stability• Directional curved vanes optimize airflow and cooling efficiency• Maintains factory brake bias, ABS, and PSM calibration• Precision-balanced to eliminate vibration and ensure smooth operation• Designed exclusively for Girodisc aluminum hats used in GT3 applications Specifications • Diameter: 380 mm• Position: Front• Material: High-carbon cast iron• Mount type: Floating two-piece system• Includes: Two rotor rings and new hardware kit• Sold/priced per pair Girodisc D1-127 Porsche 997 GT3 Front Ring FAQs Will these fit the OEM Porsche GT3 rotor hats? No. These replacement rings are designed specifically for Girodisc aluminum hats and are not compatible with OEM one-piece or PCCB setups. Which brake pads perform best with these rotors? For spirited road use, Ferodo DS2500 or Hawk HPS pads work well. For track and racing use, Pagid RS29 or Endless ME20 offer high-temp stability and consistent bite. What torque should I apply to the hardware bolts? Torque to 12 ft-lbs (16 Nm) using blue Loctite. Recheck after the first full heat cycle to ensure even seating and proper float. Are these rotors directional? Yes. Each rotor is marked for left or right installation, ensuring the internal vanes pull air through the disc to maximize cooling under sustained braking. Refresh your GT3’s braking system with Girodisc D1-127 380mm front replacement rings — engineered for durability, precision, and race-proven performance lap after lap.

D1-250 Girodisc Porsche GT2 RS Clubsport Front Replacement Rings Maximize the braking performance of your Porsche GT2 RS Clubsport with Girodisc D1-250 410mm front replacement rings. These precision-engineered rings bolt directly to your existing Girodisc aluminum hats using the included floating hardware kit. Each rotor ring is machined from high-carbon cast iron for superior thermal control, reduced fade, and consistent pedal feel under extreme braking conditions. Vehicle Fitment Compatible with:• Porsche 991 GT2 RS Clubsport (front)• Porsche 991 GT2 RS MR (Manthey Racing variant)Note: Designed exclusively for Girodisc 410mm two-piece front rotor systems. Not compatible with OEM or PCCB carbon-ceramic rotors. Features • Sold as a left/right pair with complete floating hardware kit• Direct replacements for Girodisc 410mm two-piece front rotors• CNC-machined from proprietary high-carbon cast iron for durability• Directional curved vanes enhance airflow and cooling• Maintains factory brake bias and ABS calibration• Designed exclusively for Girodisc aluminum hats – not compatible with OEM or other brands Specifications • Diameter: 410mm• Position: Front• Material: High-carbon cast iron• Mount type: Floating two-piece system• Includes: Two rings and new hardware kit• Sold/priced per pair Girodisc D1-250 Porsche GT2 RS Clubsport Front Replacement Ring FAQs Are these compatible with OEM PCCB carbon-ceramic brakes? No. The D1-250 rings are designed for Girodisc two-piece steel rotor conversions only. Can these handle full race conditions? Absolutely. These rings are engineered for the high thermal loads of GT-class racing and extended endurance events. Do they fit both GT2 RS and GT2 RS MR models? Yes. The D1-250 fits both standard GT2 RS Clubsport and Manthey Racing variants that share the 410mm front rotor dimensions. How do these compare to OEM steel rotors? Girodisc rings offer improved heat cycling, reduced weight, and longer lifespan due to the floating two-piece design. Upgrade your Porsche GT2 RS Clubsport’s braking system with Girodisc D1-250 410mm front replacement rings — built for precision, cooling, and repeatable performance at the highest levels of motorsport.

Girodisc Porsche 993 Rear Rings Restore your Porsche 993’s braking performance with Girodisc D2-103 rear replacement rings. These precision-engineered 322mm rings are designed to bolt directly onto your existing Girodisc aluminum hats, providing a cost-effective refresh of your two-piece rotor system. Each set includes both left and right rings plus all necessary new floating hardware for a secure, factory-quality installation. Vehicle Fitment Compatible with:• Porsche 993 Carrera / Carrera S• Porsche 993 Turbo• Porsche 993 Carrera 4 / 4SNote: For use with Girodisc 322mm two-piece rear rotor systems. Not compatible with OEM or carbon-ceramic rotors. Features • Sold as a left/right pair and includes new floating hardware kit• Direct replacements for Girodisc 322mm two-piece rear rotors• CNC-machined from proprietary high-carbon cast iron• Curved directional vanes improve cooling and reduce fade• Maintains OEM brake balance and ABS function• Designed exclusively for Girodisc aluminum hats – not compatible with OEM or other brands Specifications • Diameter: 322mm• Position: Rear• Material: High-carbon cast iron• Mount type: Floating two-piece system• Includes: Two rings and complete hardware kit• Sold/priced per pair Girodisc D2-103 Replacement Ring FAQs Will these fit factory Porsche rotors? No. These are designed specifically for Girodisc two-piece rotor systems and will not bolt to factory or PCCB rotors. Are both sides included? Yes. Each D2-103 kit includes both left and right replacement rings with all new hardware. Why replace only the rings? Replacing just the rings allows you to reuse your Girodisc hats, saving cost and maintaining peak braking performance. Do I need to install the new hardware? Yes. Always use the supplied new hardware for proper torque, safety, and fitment accuracy. Upgrade your Porsche 993 braking system with Girodisc D2-103 rear replacement rings — precision-built for cooling, strength, and consistent braking performance on both road and track.

Girodisc D2-250 Porsche GT2 RS Clubsport Rear Replacement Rotor Rings The Girodisc D2-250 Rear Replacement Rotor Rings are precision-engineered replacements for Girodisc two-piece rotors fitted to the Porsche 991 GT2 RS Clubsport. Designed to match the performance and fitment of the original Girodisc system, these iron rings restore braking power, cooling efficiency, and pedal consistency for track-dominant Porsche applications. Built for the Demands of Motorsport Machined and cast in the USA, each Girodisc D2-250 rotor ring is made from Girodisc’s proprietary cast iron alloy, formulated for superior strength and thermal stability under repeated high-load braking. The curved vane internal geometry functions as a centrifugal air pump, improving airflow through the rotor and dramatically reducing temperatures. Sold as a pair, these replacement rings include all necessary hardware and bolt directly onto your existing Girodisc aluminum hats. Features • Direct replacement for Girodisc Porsche 991 GT2 RS Clubsport rear rotors• Proprietary cast iron alloy for consistent friction and durability• Curved vane internal geometry for maximum cooling and airflow• Reuses Girodisc aluminum hats• Includes complete hardware kit for installation• Engineered and machined in the USA• Sold/priced per pair• Not compatible with OEM or other aftermarket hats Vehicle Fitment • Porsche 991 GT2 RS Clubsport – Rear• Fits Girodisc two-piece rotor systems using D2-250 configuration• Will not fit OEM or non-Girodisc hats Girodisc D2-250 Porsche GT2 RS Clubsport Rear Replacement Rotor Rings FAQs Do these rotors fit OEM hats or hardware? No. Girodisc replacement rings are designed specifically for Girodisc aluminum hats and should not be used with OEM or other aftermarket hardware. What’s included in the package? Each set includes two iron rotor rings (left and right) and all necessary mounting hardware for reassembly. Can I reuse my existing Girodisc hats? Yes. These rings are designed to bolt directly to your current Girodisc aluminum hats, preserving the same lightweight two-piece configuration. What are the benefits of the curved vane design? Curved vanes pull air through the rotor as it spins, helping to regulate temperature and prevent fade during heavy braking—ideal for track environments. Are these rotors directional? Yes. Each ring is marked left and right to ensure proper airflow through the curved vane system. Are they sold individually or as a set? The Girodisc D2-250 Porsche GT2 RS Clubsport Rear Replacement Rotor Rings are sold and priced per pair, including hardware. Maintain peak braking performance on your Porsche GT2 RS Clubsport with Girodisc D2-250 Replacement Rotor Rings—precision-built to the same racing-grade standards that define Girodisc performance systems.

Girodisc Porsche 992 GT3 Front Replacement Rings Refresh your Porsche’s braking power with Girodisc D1-272 front replacement rings. Designed as direct replacements for Girodisc two-piece rotors, these precision-engineered 408mm rings restore peak performance and cooling efficiency, ensuring consistent brake feel and reduced fade during aggressive driving or track use. Vehicle Fitment Compatible with:• 2022–2025 Porsche 911 GT3 (992)• 2023–2025 Porsche 911 GT3 Touring (992)• 2023–2025 Porsche 718 Cayman GT4 RS• 2023–2025 Porsche 718 Spyder RSNote: These are friction rings only. They attach to existing Girodisc aluminum hats using the supplied floating hardware kit. Race-Proven Engineering and Cooling Efficiency Girodisc rotor rings are cast in the USA from a proprietary high-carbon iron alloy designed to withstand extreme heat and repeated high-speed stops. The 72 curved internal vanes act as centrifugal pumps, pulling cool air through the disc to regulate temperature and resist fade. These rings deliver precise pedal modulation and exceptional longevity on both road and track. Features • Direct replacements for Girodisc 408mm front rotors• Fits Porsche 992 GT3, GT3 Touring, GT4 RS, and Spyder RS• High-carbon cast iron construction for superior durability• Directional curved vane design for maximum cooling• Fully machined, balanced, and finished in the USA• Includes new floating hardware kit• Sold/priced per pair Specifications • Diameter: 408mm• Position: Front• Material: High-carbon cast iron• Includes: Two rotor rings and full hardware kit• Made in the USA• Sold/priced per pair Girodisc D1-272 Replacement Ring FAQs Are these compatible with OEM Porsche rotors? No. These replacement rings are designed exclusively for Girodisc two-piece rotor systems and will not fit OEM or PCCB assemblies. Do they include new hardware? Yes. Each set comes complete with floating drive pins, washers, and bolts for secure, straightforward installation. Are they suitable for track use? Absolutely. Girodisc rotors are engineered for endurance racing, offering consistent brake feel even under prolonged high temperatures. When should I replace the rings? Replace them once they reach minimum thickness or if surface cracking extends to the edge of the disc. Rebuild your Porsche’s braking system with Girodisc D1-272 front replacement rings — precision-built, track-proven, and proudly made in the USA.