Porsche Brake Rotors

Girodisc Porsche GT3 Front Rotors The Girodisc system is a direct replacement for the OE front rotors on all Porsche 996 and 997.1 GT3 and GT2 models. No modifications are required—the discs bolt directly to the car and work perfectly with OE calipers. This upgrade offers a lighter, high-performance braking solution that maintains factory brake bias and ABS calibration while improving cooling and response. The Girodisc front rotors weigh approximately 21.0 lbs each, compared to 25.6 lbs for the stock units—a significant reduction in unsprung and rotational mass that enhances acceleration and suspension dynamics. High-Performance Construction The central hat section is crafted from U.S.-sourced 6061-T6 aircraft-grade aluminum for strength and lightness. The rotor rings are Girodisc’s proprietary cast iron, poured and machined entirely in-house in the USA. The curved vane design, developed through years of motorsport experience, acts as a centrifugal pump that forces air through the disc, reducing heat build-up and maintaining consistent braking performance under extreme conditions. Girodisc A1-019 Features Direct bolt-on replacement for OE rotors—no modifications required Lightweight two-piece floating design improves cooling and reduces rotational mass 6061-T6 aluminum hat and proprietary high-carbon iron rotor rings Curved vane design for efficient cooling airflow Floating mount system allows thermal expansion while preventing warping Cadmium-plated drive pins for long-lasting corrosion resistance Quiet operation thanks to anti-noise spring washers Fully rebuildable—replace iron rings while reusing hats and hardware Vehicle Fitment Porsche 996 GT3 (2004–2005) Porsche 996 GT2 (2002–2005) Porsche 997.1 GT3 (2006–2008) Porsche 997.1 GT3 RS (2007–2008) Note: Designed for iron brake systems. Not compatible with PCCB carbon-ceramic rotors. Technical Specifications Part Number: A1-019 Position: Front Weight: 21.0 lbs (each) OE Weight: 25.6 lbs (each) Rotor Type: Two-piece floating Hat Material: 6061-T6 aluminum, anodized Disc Material: Girodisc proprietary high-carbon cast iron Vane Design: Curved, directional Drive Pins: 10 high-strength alloy steel, cadmium-plated Hardware: Class 12.9 cap screws with hardened washers Sold/Price: Per pair Girodisc A1-019 FAQs Do I need to modify the calipers or hubs? No. These rotors are a direct replacement for the factory discs and bolt up with OEM hardware. Will they make noise during street driving? No. Girodisc uses anti-noise spring washers to allow float while keeping the system quiet for street use. Are the rings replaceable? Yes. Replacement rings can be purchased separately, allowing you to reuse the aluminum hats and hardware. Can these handle track use? Absolutely. These rotors are engineered to endure repeated high-heat cycles without cracking or warping, making them ideal for both spirited street and track driving. Upgrade your GT3’s stopping power with Girodisc’s lightweight, precision-engineered front rotors—built for performance, endurance, and control.

Girodisc Porsche 981, 718 Rear Rings Refresh your Porsche’s braking performance with Girodisc D2-035 350mm rear replacement rings. These precision-machined, high-carbon cast iron rings bolt directly to your existing Girodisc aluminum hats using the included floating hardware kit. Replace only the wear surface to restore full braking performance while retaining your lightweight Girodisc two-piece system. Vehicle Fitment Compatible with:• Porsche 981 Cayman / Boxster (rear)• Porsche 718 Cayman / Boxster (rear)Note: For Girodisc 350mm two-piece rear rotor systems only. Designed to mate with original Girodisc aluminum hats — not compatible with factory two-piece rotor hats or PCCB systems. Features • Sold as a left/right pair with new floating hardware kit• CNC-machined from high-carbon cast iron for heat capacity and strength• Curved directional vanes maximize cooling and reduce fade• Bolt-on fitment to Girodisc aluminum hats — no modifications required• Balanced and heat-treated for consistent braking feel• Manufactured in Bellingham, WA, USA Specifications • Diameter: 350mm• Position: Rear• Material: High-carbon cast iron• Mount type: Floating two-piece system• Includes: Two rings and hardware kit• Sold/priced per pair• MSRP: $780.00 Girodisc D2-035 Porsche 981 / 718 Rear Replacement Ring FAQs Can these be installed with the OEM Porsche hats? No. These are designed exclusively for Girodisc aluminum hats and are not compatible with factory two-piece rotor assemblies. Will these fit PCCB or steel brake systems? Only the Girodisc steel two-piece rotor system — they are not designed for Porsche Ceramic Composite Brakes (PCCB). Are they suitable for track use? Yes. The high-carbon alloy and floating design resist cracking and warping under repeated high-temperature braking on track. How do I know when to replace the rings? Replace them when the rotor surface reaches minimum thickness or shows visible heat checking, per Girodisc wear specifications. Restore confidence in your Porsche 981 or 718 Cayman and Boxster with Girodisc D2-035 350mm rear replacement rings — the perfect blend of precision, performance, and cost-effective service life.

AP Racing Radi-CAL 380mm Competition Brake Kit GT4 (Rear) Fit The Following Cars Porsche 981 GT4 (PCCB and Iron Rotors)  Porsche 718 GT4 (PCCB and Iron Rotors) Complete rear AP Racing Radi-CAL Competition Brake Kit. Fits all variants of the Porsche 718/981 GT4. Eliminates the need to remove the caliper for pad changes Retains OEM parking brake functionality Saves 18 unsprung lbs. vs. OEM iron brakes and weighs almost the same as the OEM PCCB system Jewel-like ENP caliper finish is incredibly durable and easy to clean AP Racing Radi-CAL with durable, ventilated stainless steel pistons (no ceramic piston caps to break) with anti-knockback springs Allows for the preservation of pricey OEM brake components Huge array of brake pad options from all major pad manufacturers Fits OEM 20" wheels without spacer 380x32mm, 72 vane AP Racing disc fits inside popular 19" wheels Every component designed to resist the heat of extended track sessions Pistons sized properly to allow for seamless integration with OEM master cylinder and ABS system Includes pad tension kit (eliminates noise) and disc burning at no additional cost Designed to work with Ap Racing front Brake Kit

AP Racing 380x34mm Replacement J Hook Rotor Rings Replacement Disc Only For AP Racing 13.01.20017 Rotor discs and installation hardware only. Center hat excluded. Fits The Following Cars (w/ OEM Iron Rotors) Porsche 991 GT3 (Front) Porsche 991 GT3RS (Front) Porsche 981 GT4 (Front) AP Racing by Essex 2-piece Competition J Hook front disc pair for 981 GT4, 991.1 & 991.2 GT3 & GT3 RS with iron discs 380mm x 34mm (14.96" x 1.34") 72 Vane, D66 Huge increase in airflow, cooling capacity, and durability vs. OEM discs Saves 2 lbs. unsprung weight per side vs. OEM iron discs Designed for: club racing, time trial, auto-x, HPDE Works with OEM calipers, no modifications required Ultralight, fully floating, anodized billet aluminum hat with float control/anti-rattle clips Sold/priced per pair of rotor rings (including hardware). AP Racing J Hook Brake Rotors – The Gold Standard in Track Day & Racing Performance Engineered for professional motorsport, HPDE, and dedicated track day use, AP Racing’s J Hook Brake Rotors deliver uncompromising performance, thermal stability, and consistent braking power. These two-piece, floating rotors are built to handle the extreme demands of road racing, with design features derived from over 50 years of elite competition—including Formula 1, NASCAR, and IMSA. Unlike conventional one-piece rotors, AP Racing’s two-piece floating design features a billet aluminum hat mated to a cast iron disc via precision-engineered bobbins. This setup allows for controlled radial expansion under high heat, minimizing distortion and coning. The result? More even pad wear, a firmer pedal feel, and longer component life, even during extended lapping sessions or endurance racing. Floating hardware includes anti-knockback spring clips that reduce piston retraction while eliminating common NVH issues like rattling. Why Choose AP Racing J Hook Rotors? Advanced Cooling, Superior Bite, Unmatched Durability At the heart of every rotor is AP Racing’s proprietary high-carbon iron alloy, developed to withstand repeated thermal cycling without cracking or warping. Internally, directional vanes—far superior to OEM pillar or straight vane designs—maximize airflow and cooling. With 60 to 84 vanes per rotor, AP Racing achieves faster heat evacuation, reduced brake fade, and a more consistent friction surface. These rotors are left/right-specific for optimal airflow and balance. The exclusive J Hook slot pattern offers enhanced initial bite and promotes uniform heat distribution across the rotor face, reducing pad deposits and vibration. Unlike drilled rotors or straight-slot competitors, the J Hook design provides cleaner pad transfer during bed-in and superior modulation under braking—ideal for serious drivers who demand feedback and control. Yes, you might hear a little more whirr, but you’ll gain the stopping power, consistency, and longevity your lap times demand. Premium Components, Affordable Performance The rotor hats are CNC-machined from 6061-T6 billet aluminum and hard anodized for strength and heat resistance. Scalloped edges under the hat further assist heat dissipation. All hardware is U.S.-made to AP Racing spec, the same quality found on pro-level racing platforms. And while these rotors are race-proven, they’re also surprisingly cost-effective to replace. Don’t settle for cheap rotors that crack after a weekend—AP’s J Hook rings offer better durability and real long-term value. Fewer replacements mean more track time, less downtime, and peace of mind knowing you're running the best. Used by Champions. Trusted by Experts. From endurance racers to HPDE enthusiasts, AP Racing brake rotors are trusted worldwide for their reliability, longevity, and performance under pressure. Whether you're shaving seconds off your lap time or building a dedicated track car, the J Hook delivers a professional-grade solution that won’t let you down. AP Racing J Hook Brake Rotors for Auto Racing, Track Days & HPDE Why Rotor Design Matters: Heat Expansion and Floating Technology As with most metals, iron brake discs expand significantly under heat. When temperatures rise, the disc grows radially—expanding in both diameter and circumference. Traditional one-piece rotors struggle to accommodate this natural expansion. As the outer edge pulls away from the center under heat stress, it creates a condition called “coning”—a distortion that compromises pad-to-rotor contact. This distortion can lead to uneven pad wear, brake tapering, and an inconsistent, long brake pedal. AP Racing two-piece floating brake rotors are purpose-built to eliminate these issues. Engineered with “float” built into the disc or hat assembly, these rotors feature oblong-shaped mounting holes that allow the hardware to slide as the disc heats up. This flexibility ensures the disc runs true within the caliper under high-temperature loads, effectively reducing distortion, minimizing pad taper and stress cracks, and promoting longer component life. Custom Mounting Hardware & Anti-Knockback Spring Clips AP Racing rotors utilize application-specific, U.S.-made mounting hardware—not generic bolts. These premium components are the exact parts used in AP’s professional motorsport products, engineered to withstand the rigors of competitive racing. To manage lateral disc motion that can push caliper pistons backward (known as knockback), AP Racing integrates anti-knockback spring clips on alternating bobbins—five on a ten-bolt setup, six on a twelve-bolt disc. These clips keep the aluminum hat and iron disc ring properly aligned while still allowing for radial float. Bonus: they eliminate annoying rattles and vibrations, ensuring a quieter, more refined braking experience. High-Performance Hat Design for Heat Isolation The disc hats in AP Racing’s two-piece floating rotors are CNC-machined from 6061-T6 billet aluminum and finished with a hard anodized coating. This high-strength aluminum alloy was selected for its ability to maintain structural integrity even at elevated temperatures. AP adds scalloped channels beneath the hat to further encourage airflow and heat evacuation from the outer disc face, minimizing thermal transfer to hubs and wheel bearings—helping reduce maintenance costs on these expensive components. Internal Vane Engineering: Airflow Optimization & Thermal Stability AP Racing’s internal vane design sets them apart from OEM and most aftermarket competitors. While many factory brake discs use non-directional pillar vanes (low-cost and NVH-focused), AP Racing rotors use directional vanes engineered for maximum airflow. These rotors are side-specific—meaning you’ll receive a unique left and right disc in each set—ensuring optimized cooling through strategic vane orientation and shape. Beyond that, AP Racing rotors feature a superior vane count, typically ranging from 60 to 84 vanes, compared to 30–48 in most aftermarket rotors. After extensive CFD and thermal analysis, this high vane count was proven to: Increase airspeed and thermal transfer Reduce recirculation and deflection at the disc face Minimize coning, cracking, and brake fade Deliver more even pad contact and extended rotor life J Hook Slot Pattern: Exclusive to AP Racing Slots and drill holes may improve initial bite, but they also introduce “cool spots” in the rotor face—areas of uneven heating that can lead to stress risers, cracks, and pad vibration. OEM rotors often avoid this by leaving the disc face blank, but that compromises bite and brake feel. AP Racing’s patented J Hook design, developed through rigorous R&D, solves this problem. The hooks are meticulously spaced around the disc’s circumference and from hat to edge, forming a continuous distortion path that ensures even heat distribution. This encourages uniform pad deposits during bed-in, helps reduce judder and cracking, and improves consistency under repeated high-load braking. In addition, the J Hook slots provide more leading edges for pads to grip than traditional curved slots or blank rotors. While this might generate a mild whirring sound during braking, the benefits—more bite, cleaner bedding, better pedal feel—make it the top choice for committed racers and serious track day drivers. Metallurgy Backed by 50+ Years of Motorsport Leadership AP Racing's reputation is built on performance, and their proprietary iron alloy used in J Hook rotors is no exception. Drawing from over five decades of elite motorsport experience, including 750+ Formula 1 wins and widespread use across NASCAR, AP’s engineers have developed a disc alloy that excels under sustained racing temperatures and stress. Where OEM discs focus on affordability and mass production, AP Racing’s J Hook rotors are purpose-built for motorsport durability and heat resistance. Affordable Replacement Cost: Serious Value for Serious Drivers Even the best brake rotors are consumables. When you drive hard—especially at the track—your discs will eventually wear out. That’s why AP Racing designed their replacement iron rings to be cost-effective, allowing you to replace worn parts without breaking the bank. Compare that to constantly buying cheap $150 rotors every weekend—rotors that can't handle the heat and need to be swapped frequently. With AP Racing’s J Hook rotors, you get longer service intervals, less downtime, and better performance over time, making them an incredibly smart long-term investment. Proven on Track. Trusted by Champions. Top-tier racing teams rely on AP Racing J Hook rotors for one reason: they perform under pressure. Whether you're running time trials, attending HPDE events, or competing in wheel-to-wheel racing, these rotors offer professional-grade reliability, safety, and performance. Bedding and Preparation of AP Racing J Hook Discs Properly preparing your new brake discs before heavy use is extremely important. The goal of bedding-in your brake pads and discs is to mate them together properly and prepare them for heavy use.  When prepared properly, or bed-in, your pads will transfer a thin layer of material to the disc face (transfer layer).  The pads in your caliper will then actually ride on that thin layer of pad material you’ve put down on the rotor, rather than rubbing directly on the iron rotor face.  A good transfer layer is going to give you superior brake pedal feel, less noise, superior pad wear, and lower the chances of cracking your discs. Important Notes- PLEASE READ! First, make sure you are on a closed course to perform a proper bed-in.  Do NOT perform the procedure on public roads.  You need a stretch of asphalt with long straights, good visibility, and no potential obstructions.  Make sure you are in a position to safely and repeatedly attain the necessary speeds to perform the bed-in procedure.  A controlled racetrack is the best place to perform this procedure.  AP Racing and Competition Motorsport in no way suggest or condone speeding on public roads or breaking the law in your car, nor do we take responsibility for any damage or injury that occurs as a result of using our product or these procedures.  You are performing the bed-in procedure at your own risk.  During these procedures, it’s critical that you never come to a complete stop with your foot on the brake pedal.  If you have brake ducts on your car, you may want to block them off to allow your brake system to heat up easily. The procedure outlined below is a generic procedure for most types of mild race pad.  Please check your pad manufacturer’s recommended bed-in procedure. Accelerate to approximately 60mph and then decelerate down to 5 mph.  If your car has ABS, you should try to hold the brakes at a point just before ABS intervention.  Once the car slows to 5mph, immediately accelerate back up to about 60mph, and brake again to roughly 5mph.  Repeat this series of stopping and accelerating 8 to 10 times.  Again, do not come to a complete stop with your foot on the brake pedal. Cool the brake system down by cruising at 45mph+ for 5 to 10 minutes. Visually inspect your discs.  They should be a blue/grey color (instead of shiny silver), and have an even layer of pad material across and around the entire rotor face. If the AP Racing rotors don’t have a layer of pad material on them, perform another series of stops in the manner outlined above.

AP Racing 390x32mm 2-piece J Hook Rear Brake Rotors - Porsche (OEM PCCB) Fit The Following Cars (w/ OEM PCCB Rotors) Porsche 992 GT3 (Rear) Porsche 992 GT3RS (Rear) Porsche 718/982 GT4RS (Rear) Porsche 991 GT2RS/GT3/GT3RS (Rear) Porsche 981 GT4 (Rear) Sold/priced per pair. AP Racing 2-piece Competition J Hook rear iron disc pair for 991/992 GT3/RS and 718 GT4/Spyder RS to replace PCCB discs. 390 x 32mm (15.35" x 1.26") Huge increase in airflow, cooling capacity, and durability vs. OEM PCCB discs Drastically less expense long-term running costs vs. PCCB Must useGT3/RS Iron disc pad shape used in OEM iron system (not compatible with OE PCCB Pad shape) Allows normal function of OEM parking brake 100% more internal cooling vanes vs the OEM PCCB's Same weight as OEM 380 x 34mm iron discs, despite larger size Designed for: club racing, time trial, auto-x, HPDE Works with OEM calipers and wheels, no modifications required Ultralight, fully floating, anodized billet aluminum hat with float control/anti-rattle clips AP Racing J Hook Brake Rotors – The Gold Standard in Track Day & Racing Performance Engineered for professional motorsport, HPDE, and dedicated track day use, AP Racing’s J Hook Brake Rotors deliver uncompromising performance, thermal stability, and consistent braking power. These two-piece, floating rotors are built to handle the extreme demands of road racing, with design features derived from over 50 years of elite competition—including Formula 1, NASCAR, and IMSA. Unlike conventional one-piece rotors, AP Racing’s two-piece floating design features a billet aluminum hat mated to a cast iron disc via precision-engineered bobbins. This setup allows for controlled radial expansion under high heat, minimizing distortion and coning. The result? More even pad wear, a firmer pedal feel, and longer component life, even during extended lapping sessions or endurance racing. Floating hardware includes anti-knockback spring clips that reduce piston retraction while eliminating common NVH issues like rattling. Why Choose AP Racing J Hook Rotors? Advanced Cooling, Superior Bite, Unmatched Durability At the heart of every rotor is AP Racing’s proprietary high-carbon iron alloy, developed to withstand repeated thermal cycling without cracking or warping. Internally, directional vanes—far superior to OEM pillar or straight vane designs—maximize airflow and cooling. With 60 to 84 vanes per rotor, AP Racing achieves faster heat evacuation, reduced brake fade, and a more consistent friction surface. These rotors are left/right-specific for optimal airflow and balance. The exclusive J Hook slot pattern offers enhanced initial bite and promotes uniform heat distribution across the rotor face, reducing pad deposits and vibration. Unlike drilled rotors or straight-slot competitors, the J Hook design provides cleaner pad transfer during bed-in and superior modulation under braking—ideal for serious drivers who demand feedback and control. Yes, you might hear a little more whirr, but you’ll gain the stopping power, consistency, and longevity your lap times demand. Premium Components, Affordable Performance The rotor hats are CNC-machined from 6061-T6 billet aluminum and hard anodized for strength and heat resistance. Scalloped edges under the hat further assist heat dissipation. All hardware is U.S.-made to AP Racing spec, the same quality found on pro-level racing platforms. And while these rotors are race-proven, they’re also surprisingly cost-effective to replace. Don’t settle for cheap rotors that crack after a weekend—AP’s J Hook rings offer better durability and real long-term value. Fewer replacements mean more track time, less downtime, and peace of mind knowing you're running the best. Used by Champions. Trusted by Experts. From endurance racers to HPDE enthusiasts, AP Racing brake rotors are trusted worldwide for their reliability, longevity, and performance under pressure. Whether you're shaving seconds off your lap time or building a dedicated track car, the J Hook delivers a professional-grade solution that won’t let you down.   AP Racing J Hook Brake Rotors for Auto Racing, Track Days & HPDE Why Rotor Design Matters: Heat Expansion and Floating Technology As with most metals, iron brake discs expand significantly under heat. When temperatures rise, the disc grows radially—expanding in both diameter and circumference. Traditional one-piece rotors struggle to accommodate this natural expansion. As the outer edge pulls away from the center under heat stress, it creates a condition called “coning”—a distortion that compromises pad-to-rotor contact. This distortion can lead to uneven pad wear, brake tapering, and an inconsistent, long brake pedal. AP Racing two-piece floating brake rotors are purpose-built to eliminate these issues. Engineered with “float” built into the disc or hat assembly, these rotors feature oblong-shaped mounting holes that allow the hardware to slide as the disc heats up. This flexibility ensures the disc runs true within the caliper under high-temperature loads, effectively reducing distortion, minimizing pad taper and stress cracks, and promoting longer component life. Custom Mounting Hardware & Anti-Knockback Spring Clips AP Racing rotors utilize application-specific, U.S.-made mounting hardware—not generic bolts. These premium components are the exact parts used in AP’s professional motorsport products, engineered to withstand the rigors of competitive racing. To manage lateral disc motion that can push caliper pistons backward (known as knockback), AP Racing integrates anti-knockback spring clips on alternating bobbins—five on a ten-bolt setup, six on a twelve-bolt disc. These clips keep the aluminum hat and iron disc ring properly aligned while still allowing for radial float. Bonus: they eliminate annoying rattles and vibrations, ensuring a quieter, more refined braking experience. High-Performance Hat Design for Heat Isolation The disc hats in AP Racing’s two-piece floating rotors are CNC-machined from 6061-T6 billet aluminum and finished with a hard anodized coating. This high-strength aluminum alloy was selected for its ability to maintain structural integrity even at elevated temperatures. AP adds scalloped channels beneath the hat to further encourage airflow and heat evacuation from the outer disc face, minimizing thermal transfer to hubs and wheel bearings—helping reduce maintenance costs on these expensive components. Internal Vane Engineering: Airflow Optimization & Thermal Stability AP Racing’s internal vane design sets them apart from OEM and most aftermarket competitors. While many factory brake discs use non-directional pillar vanes (low-cost and NVH-focused), AP Racing rotors use directional vanes engineered for maximum airflow. These rotors are side-specific—meaning you’ll receive a unique left and right disc in each set—ensuring optimized cooling through strategic vane orientation and shape. Beyond that, AP Racing rotors feature a superior vane count, typically ranging from 60 to 84 vanes, compared to 30–48 in most aftermarket rotors. After extensive CFD and thermal analysis, this high vane count was proven to: Increase airspeed and thermal transfer Reduce recirculation and deflection at the disc face Minimize coning, cracking, and brake fade Deliver more even pad contact and extended rotor life J Hook Slot Pattern: Exclusive to AP Racing Slots and drill holes may improve initial bite, but they also introduce “cool spots” in the rotor face—areas of uneven heating that can lead to stress risers, cracks, and pad vibration. OEM rotors often avoid this by leaving the disc face blank, but that compromises bite and brake feel. AP Racing’s patented J Hook design, developed through rigorous R&D, solves this problem. The hooks are meticulously spaced around the disc’s circumference and from hat to edge, forming a continuous distortion path that ensures even heat distribution. This encourages uniform pad deposits during bed-in, helps reduce judder and cracking, and improves consistency under repeated high-load braking. In addition, the J Hook slots provide more leading edges for pads to grip than traditional curved slots or blank rotors. While this might generate a mild whirring sound during braking, the benefits—more bite, cleaner bedding, better pedal feel—make it the top choice for committed racers and serious track day drivers. Metallurgy Backed by 50+ Years of Motorsport Leadership AP Racing's reputation is built on performance, and their proprietary iron alloy used in J Hook rotors is no exception. Drawing from over five decades of elite motorsport experience, including 750+ Formula 1 wins and widespread use across NASCAR, AP’s engineers have developed a disc alloy that excels under sustained racing temperatures and stress. Where OEM discs focus on affordability and mass production, AP Racing’s J Hook rotors are purpose-built for motorsport durability and heat resistance. Affordable Replacement Cost: Serious Value for Serious Drivers Even the best brake rotors are consumables. When you drive hard—especially at the track—your discs will eventually wear out. That’s why AP Racing designed their replacement iron rings to be cost-effective, allowing you to replace worn parts without breaking the bank. Compare that to constantly buying cheap $150 rotors every weekend—rotors that can't handle the heat and need to be swapped frequently. With AP Racing’s J Hook rotors, you get longer service intervals, less downtime, and better performance over time, making them an incredibly smart long-term investment. Proven on Track. Trusted by Champions. Top-tier racing teams rely on AP Racing J Hook rotors for one reason: they perform under pressure. Whether you're running time trials, attending HPDE events, or competing in wheel-to-wheel racing, these rotors offer professional-grade reliability, safety, and performance. Bedding and preparation of AP Racing J Hook Disc Properly preparing your new brake discs before heavy use is extremely important. The goal of bedding-in your brake pads and discs is to mate them together properly and prepare them for heavy use.  When prepared properly, or bed-in, your pads will transfer a thin layer of material to the disc face (transfer layer).  The pads in your caliper will then actually ride on that thin layer of pad material you’ve put down on the rotor, rather than rubbing directly on the iron rotor face.  A good transfer layer is going to give you superior brake pedal feel, less noise, superior pad wear, and lower the chances of cracking your discs. Important Notes- PLEASE READ! First, make sure you are on a closed course to perform a proper bed-in.  Do NOT perform the procedure on public roads.  You need a stretch of asphalt with long straights, good visibility, and no potential obstructions.  Make sure you are in a position to safely and repeatedly attain the necessary speeds to perform the bed-in procedure.  A controlled racetrack is the best place to perform this procedure.  AP Racing and Competition Motorsport in no way suggest or condone speeding on public roads or breaking the law in your car, nor do we take responsibility for any damage or injury that occurs as a result of using our product or these procedures.  You are performing the bed-in procedure at your own risk.  During these procedures, it’s critical that you never come to a complete stop with your foot on the brake pedal.  If you have brake ducts on your car, you may want to block them off to allow your brake system to heat up easily. The procedure outlined below is a generic procedure for most types of mild race pad.  Please check your pad manufacturer’s recommended bed-in procedure. Accelerate to approximately 60mph and then decelerate down to 5 mph.  If your car has ABS, you should try to hold the brakes at a point just before ABS intervention.  Once the car slows to 5mph, immediately accelerate back up to about 60mph, and brake again to roughly 5mph.  Repeat this series of stopping and accelerating 8 to 10 times.  Again, do not come to a complete stop with your foot on the brake pedal. Cool the brake system down by cruising at 45mph+ for 5 to 10 minutes. Visually inspect your discs.  They should be a blue/grey color (instead of shiny silver), and have an even layer of pad material across and around the entire rotor face. If the AP Racing rotors don’t have a layer of pad material on them, perform another series of stops in the manner outlined above.

AP Racing by Essex 2-piece "S" Vane J Hook Front Brake Rotors (Front 408 x 34mm)- Porsche 992 GT3, GT3 RS Iron & PCCB Fit The Following Cars (w/ OEM Iron Rotors or PCCB Rotors) Porsche 992 GT3 (Front) Porsche 992 GT3RS (Front) Sold/priced per pair. AP Racing 2-piece S Vane Competition J Hook front disc pair for 992 GT3 and GT3 RS with iron or PCCB discs. ***Note for PCCB cars - must be used with the smaller D62 iron disc pad shape (Ferodo FCP4664 - DS3.12 / DS1.11) Massive increase in airflow, cooling capacity, and durability vs. OEM discs or even conventional curved vane discs 408mm x 34mm (16.06" x 1.34") , 84 Sinusoidal "wave" vanes, D62 radial depth Designed for: club racing, time trial, autocross, HPDE Works with OEM calipers, no modifications required Ultralight, fully floating, anodized billet aluminum hat with float control/anti-rattle clips We are introducing a new internal vane technology in our front 2-piece discs for the 992 GT3. It is called the Sinusoidal Vane, which AP sometimes refers to internally as the 'Wave' Vane for obvious reasons as you’ll see below. This tech is something that has helped AP Racing brake systems win championships in international GT racing, as well as multiple NASCAR Cup championships here in North America. As one of the most desirable track weapons on the planet, we wanted the 992 GT3 to be the first production car application for this technology in North America. Just as AP Racing's Radi-CAL calipers set a new benchmark for caliper stability, cooling, and durability, the Sinusoidal Vanes have done the same for iron racing discs. The concept for this disc design originated in NASCAR Cup. Up until the debut of the Next Gen car (for which AP/Essex are supplying the spec brake package), we were cramming our brake systems inside tiny 15” wheels. Trying to squeeze adequate brake thermal mass into a wheel that small is incredibly challenging, particularly when you have a 1,000 HP and 3,000 pounds mashing on them every few seconds from 200 mph…for hours on end! In a wheel that small, there isn’t anywhere for the heat to go, and the durability of every component is crucial. We were constantly looking for ways to provide the Cup teams with increased durability, stability, and cooling, and that’s what led AP to this technology. Benefits of the Wave Vane disc technology vs. traditional curved vanes: Increased thermal stability- Wild temperature swings are what causes discs to crack. When you stand on the brakes for an approaching corner, your disc temperatures skyrocket and the iron expands. As you travel down the subsequent straight, the discs are blasted with cooling air. The longer the straight and the higher the speed, the greater the temperature drop, and the further the iron contracts. This expansion and contraction cycle places a huge amount of stress on the iron and is what causes them to eventually crack. That’s why tracks with relatively slow corners at the end of high-speed straights, followed by another long straight, decimate brake discs (think Watkins Glen or Road America). In an ideal world, once you brought your discs up to race temps, you would keep them at a constant temperature for the entire session. The Sinusoidal Vane brings the discs closer to that goal by decreasing the difference between the maximum and minimum disc temperature by as much as 35%. That means a less dramatic temperature swing and greater crack resistance and durability. Reduced maximum disc temperatures by 10%+: Not only are temperature swings less intense with the Wave Vane, the maximum temperatures reached are substantially lower. For example, in one NASCAR test the Wave Vane discs showed a peak temp of 1328F and a minimum temp of 1085F (delta of 243F), while the traditional curved vanes maxed out at 1490F and a min of 1121F (delta of 369F). Not only was the difference between min and max more subdued, the max temperature reached by the Wave Vane disc was 162F lower! Increased cooling surface area- Each of the internal Wave Vanes has a larger cooling surface area vs. a traditional curved vane. Greater support for the disc face- A disc’s internal vane structure provides the support lattice behind the disc face. Having many internal vanes impacts airspeed and heat transfer through the disc, reduces air recirculation between vanes, and reduces deflection at the disc face. In practical terms, a disc with a high number of vanes is more thermally stable, maintains more even contact with the brake pads (which reduces uneven pad deposits/judder), and is less prone to distortion. In summary, the Wave Vane design provides even greater support for the disc face than AP’s standard curved vane designs. Reduced weight- The Wave Vane design provides a slight unsprung weight reduction vs. a similar disc with curved internal vanes. AP Racing J Hook Brake Rotors – The Gold Standard in Track Day & Racing Performance Engineered for professional motorsport, HPDE, and dedicated track day use, AP Racing’s J Hook Brake Rotors deliver uncompromising performance, thermal stability, and consistent braking power. These two-piece, floating rotors are built to handle the extreme demands of road racing, with design features derived from over 50 years of elite competition—including Formula 1, NASCAR, and IMSA. Unlike conventional one-piece rotors, AP Racing’s two-piece floating design features a billet aluminum hat mated to a cast iron disc via precision-engineered bobbins. This setup allows for controlled radial expansion under high heat, minimizing distortion and coning. The result? More even pad wear, a firmer pedal feel, and longer component life, even during extended lapping sessions or endurance racing. Floating hardware includes anti-knockback spring clips that reduce piston retraction while eliminating common NVH issues like rattling. Why Choose AP Racing J Hook Rotors? Advanced Cooling, Superior Bite, Unmatched Durability At the heart of every rotor is AP Racing’s proprietary high-carbon iron alloy, developed to withstand repeated thermal cycling without cracking or warping. Internally, directional vanes—far superior to OEM pillar or straight vane designs—maximize airflow and cooling. With 60 to 84 vanes per rotor, AP Racing achieves faster heat evacuation, reduced brake fade, and a more consistent friction surface. These rotors are left/right-specific for optimal airflow and balance. The exclusive J Hook slot pattern offers enhanced initial bite and promotes uniform heat distribution across the rotor face, reducing pad deposits and vibration. Unlike drilled rotors or straight-slot competitors, the J Hook design provides cleaner pad transfer during bed-in and superior modulation under braking—ideal for serious drivers who demand feedback and control. Yes, you might hear a little more whirr, but you’ll gain the stopping power, consistency, and longevity your lap times demand. Premium Components, Affordable Performance The rotor hats are CNC-machined from 6061-T6 billet aluminum and hard anodized for strength and heat resistance. Scalloped edges under the hat further assist heat dissipation. All hardware is U.S.-made to AP Racing spec, the same quality found on pro-level racing platforms. And while these rotors are race-proven, they’re also surprisingly cost-effective to replace. Don’t settle for cheap rotors that crack after a weekend—AP’s J Hook rings offer better durability and real long-term value. Fewer replacements mean more track time, less downtime, and peace of mind knowing you're running the best. Used by Champions. Trusted by Experts. From endurance racers to HPDE enthusiasts, AP Racing brake rotors are trusted worldwide for their reliability, longevity, and performance under pressure. Whether you're shaving seconds off your lap time or building a dedicated track car, the J Hook delivers a professional-grade solution that won’t let you down.   AP Racing J Hook Brake Rotors for Auto Racing, Track Days & HPDE Why Rotor Design Matters: Heat Expansion and Floating Technology As with most metals, iron brake discs expand significantly under heat. When temperatures rise, the disc grows radially—expanding in both diameter and circumference. Traditional one-piece rotors struggle to accommodate this natural expansion. As the outer edge pulls away from the center under heat stress, it creates a condition called “coning”—a distortion that compromises pad-to-rotor contact. This distortion can lead to uneven pad wear, brake tapering, and an inconsistent, long brake pedal. AP Racing two-piece floating brake rotors are purpose-built to eliminate these issues. Engineered with “float” built into the disc or hat assembly, these rotors feature oblong-shaped mounting holes that allow the hardware to slide as the disc heats up. This flexibility ensures the disc runs true within the caliper under high-temperature loads, effectively reducing distortion, minimizing pad taper and stress cracks, and promoting longer component life. Custom Mounting Hardware & Anti-Knockback Spring Clips AP Racing rotors utilize application-specific, U.S.-made mounting hardware—not generic bolts. These premium components are the exact parts used in AP’s professional motorsport products, engineered to withstand the rigors of competitive racing. To manage lateral disc motion that can push caliper pistons backward (known as knockback), AP Racing integrates anti-knockback spring clips on alternating bobbins—five on a ten-bolt setup, six on a twelve-bolt disc. These clips keep the aluminum hat and iron disc ring properly aligned while still allowing for radial float. Bonus: they eliminate annoying rattles and vibrations, ensuring a quieter, more refined braking experience. High-Performance Hat Design for Heat Isolation The disc hats in AP Racing’s two-piece floating rotors are CNC-machined from 6061-T6 billet aluminum and finished with a hard anodized coating. This high-strength aluminum alloy was selected for its ability to maintain structural integrity even at elevated temperatures. AP adds scalloped channels beneath the hat to further encourage airflow and heat evacuation from the outer disc face, minimizing thermal transfer to hubs and wheel bearings—helping reduce maintenance costs on these expensive components. J Hook Slot Pattern: Exclusive to AP Racing Slots and drill holes may improve initial bite, but they also introduce “cool spots” in the rotor face—areas of uneven heating that can lead to stress risers, cracks, and pad vibration. OEM rotors often avoid this by leaving the disc face blank, but that compromises bite and brake feel. AP Racing’s patented J Hook design, developed through rigorous R&D, solves this problem. The hooks are meticulously spaced around the disc’s circumference and from hat to edge, forming a continuous distortion path that ensures even heat distribution. This encourages uniform pad deposits during bed-in, helps reduce judder and cracking, and improves consistency under repeated high-load braking. In addition, the J Hook slots provide more leading edges for pads to grip than traditional curved slots or blank rotors. While this might generate a mild whirring sound during braking, the benefits—more bite, cleaner bedding, better pedal feel—make it the top choice for committed racers and serious track day drivers. Metallurgy Backed by 50+ Years of Motorsport Leadership AP Racing's reputation is built on performance, and their proprietary iron alloy used in J Hook rotors is no exception. Drawing from over five decades of elite motorsport experience, including 750+ Formula 1 wins and widespread use across NASCAR, AP’s engineers have developed a disc alloy that excels under sustained racing temperatures and stress. Where OEM discs focus on affordability and mass production, AP Racing’s J Hook rotors are purpose-built for motorsport durability and heat resistance. Affordable Replacement Cost: Serious Value for Serious Drivers Even the best brake rotors are consumables. When you drive hard—especially at the track—your discs will eventually wear out. That’s why AP Racing designed their replacement iron rings to be cost-effective, allowing you to replace worn parts without breaking the bank. Compare that to constantly buying cheap $150 rotors every weekend—rotors that can't handle the heat and need to be swapped frequently. With AP Racing’s J Hook rotors, you get longer service intervals, less downtime, and better performance over time, making them an incredibly smart long-term investment. Proven on Track. Trusted by Champions. Top-tier racing teams rely on AP Racing J Hook rotors for one reason: they perform under pressure. Whether you're running time trials, attending HPDE events, or competing in wheel-to-wheel racing, these rotors offer professional-grade reliability, safety, and performance. Bedding and preparation of AP Racing J Hook Disc Properly preparing your new brake discs before heavy use is extremely important. The goal of bedding-in your brake pads and discs is to mate them together properly and prepare them for heavy use.  When prepared properly, or bed-in, your pads will transfer a thin layer of material to the disc face (transfer layer).  The pads in your caliper will then actually ride on that thin layer of pad material you’ve put down on the rotor, rather than rubbing directly on the iron rotor face.  A good transfer layer is going to give you superior brake pedal feel, less noise, superior pad wear, and lower the chances of cracking your discs. Important Notes- PLEASE READ! First, make sure you are on a closed course to perform a proper bed-in.  Do NOT perform the procedure on public roads.  You need a stretch of asphalt with long straights, good visibility, and no potential obstructions.  Make sure you are in a position to safely and repeatedly attain the necessary speeds to perform the bed-in procedure.  A controlled racetrack is the best place to perform this procedure.  AP Racing and Competition Motorsport in no way suggest or condone speeding on public roads or breaking the law in your car, nor do we take responsibility for any damage or injury that occurs as a result of using our product or these procedures.  You are performing the bed-in procedure at your own risk.  During these procedures, it’s critical that you never come to a complete stop with your foot on the brake pedal.  If you have brake ducts on your car, you may want to block them off to allow your brake system to heat up easily. The procedure outlined below is a generic procedure for most types of mild race pad.  Please check your pad manufacturer’s recommended bed-in procedure. Accelerate to approximately 60mph and then decelerate down to 5 mph.  If your car has ABS, you should try to hold the brakes at a point just before ABS intervention.  Once the car slows to 5mph, immediately accelerate back up to about 60mph, and brake again to roughly 5mph.  Repeat this series of stopping and accelerating 8 to 10 times.  Again, do not come to a complete stop with your foot on the brake pedal. Cool the brake system down by cruising at 45mph+ for 5 to 10 minutes. Visually inspect your discs.  They should be a blue/grey color (instead of shiny silver), and have an even layer of pad material across and around the entire rotor face. If the AP Racing rotors don’t have a layer of pad material on them, perform another series of stops in the manner outlined above.

Performance Friction PFC 380.070.63-64 380mm Two-Piece Front Floating Racing Brake Rotors Fit The Following Cars (w/ OEM Iron Rotors) Porsche 991 GT3 (Front) Porsche 991 GT3RS (Front) Porsche 981 GT4 (Front) PFC the manufacturer of Porsche Cup braking systems developed a 380x34mm front rotor replacement kit that is a direct replacement for the OEM Iron Brake rotors.  Performance Friction PFC V3 Discs with Zero Failure Technology Unique Rotor and Hat interface, eliminating most hardware. The elimination of hardware reduces weight, complexity, and installation time for less down time and more seat time on the track.  Replace your rotor discs in minutes with a flat head screwdriver PFC metallurgy specified for high Thermal stability and mechanical strength for increased longevity 48 vane geometry engineered for increased airflow for increased brake cooling during the heat of the battle while on track Patented slot pattern for increased initial bit and pad surface conditioning Lightweight forged hard anodized aluminum hat for increased durability and performance The two-piece PFC V3 design allows for disc-only replacement as well, minimizing future replacement costs and delivering outstanding performance. Sold/priced per pair.

Porsche GT4 Clubsport Front Rotors (380x32) The Girodisc system is a direct replacement for the factory cup car discs on the Porsche GT4 Clubsport. No modifications are required—the rotors bolt directly to the car and integrate perfectly with the OEM calipers. This upgrade provides exceptional cooling capacity, lighter weight, and superior durability compared to factory rotors, making it ideal for both professional racing and advanced track-day drivers. Motorsport-Grade Design, Made in the USA Each Girodisc rotor is precision-engineered and manufactured in-house using premium domestic materials. The central hat section is CNC-machined from 6061-T6 aircraft-grade aluminum, while the rotor rings are cast from Girodisc’s proprietary high-carbon iron alloy. This combination delivers outstanding thermal stability and braking consistency under the harshest track conditions. The 380x32 mm size provides increased surface area and heat capacity to reduce fade during extended sessions. Vehicle Fitment Porsche Cayman GT4 Clubsport (981 & 718) Porsche Cayman GT4 MR (Manthey Racing) Porsche Cayman GT4 Competition / Trackday models Features Direct OEM Replacement: Bolts directly to factory hubs and calipers with no modifications required. Lightweight Two-Piece Construction: Reduces unsprung and rotating mass for faster response and improved handling. Curved Vane Cooling: Developed in racing to act as a centrifugal pump, pulling cooling air through the disc for superior heat management. Floating Mount System: Uses 10–12 high-strength alloy steel drive pins secured with anti-noise spring washers, allowing thermal expansion while eliminating rattle and vibration. Replaceable Rotor Rings: The aluminum hats are reusable—only the iron rotor rings need to be replaced when worn. Made in the USA: Every component is designed, machined, and assembled in Girodisc’s U.S. facility to exacting motorsport standards. Additional Notes If your GT4 Clubsport uses OEM center lock wheels, please select the center lock drive pin option when ordering. When paired with performance brake pads and high-temperature brake fluid, these rotors create a highly durable, fade-resistant system that eliminates the common issues of warped or overheated factory discs. FAQs – Porsche GT4 Clubsport Front Rotors (380x32) Are these rotors a direct fit for factory calipers? Yes, they’re a direct bolt-on replacement for OEM calipers—no adapters or modifications are needed. Can they be used on both 981 and 718 GT4 Clubsport models? Yes, these rotors fit both generations of the GT4 Clubsport, including MR and Competition variants. Do I need special hardware? All hardware is included, and installation uses factory mounting points. Are they sold as a pair? Yes, Girodisc rotors are sold and priced per pair. Upgrade your Porsche GT4 Clubsport’s braking system with Girodisc’s lightweight, floating 2-piece rotors for improved cooling, faster response, and race-proven reliability on every lap.

Porsche 997 GT3 Cup 380x34mm Front Rotors Girodisc 2-piece floating front rotors are a direct, high-performance replacement for the factory discs on all Porsche 997.2 GT3 and GT2 models, including Cup applications. Designed to bolt directly to the car and work with OEM calipers, they allow continued use of unmodified factory pads—unlike most aftermarket solutions for this platform. This upgrade maintains factory brake bias and ABS function while reducing weight, improving cooling, and enhancing overall braking consistency. Each assembly features a precision-machined 6061-T6 aluminum hat mated to Girodisc’s proprietary high-carbon cast-iron rotor rings. The 380x34mm curved vane design acts as a centrifugal pump, drawing cooling air through the disc for outstanding heat management and fade resistance under high-load track conditions. Every component is designed, cast, and machined in-house in the USA to exacting motorsport standards. Precision-Engineered Performance Vehicle Fitment Porsche 997.2 GT3 Porsche 997.2 GT2 Porsche 997 GT3 Cup Girodisc A1-126 Features Direct OEM replacement: Fits OEM calipers and hardware without modifications or special adapters. Curved vane design: 12 directional vanes circulate air through the rotor to manage temperature and prevent fade. Floating mount hardware: Cadmium-plated steel drive pins with anti-noise washers allow for thermal expansion and eliminate rattling. Lightweight two-piece construction: Reduces unsprung and rotational mass for sharper steering and faster response. Serviceable system: Replace only the cast-iron rings when worn while reusing the aluminum hats. Made in the USA: All Girodisc rotors are designed, cast, and machined domestically for uncompromising precision. Girodisc A1-126 FAQs Can these be used with factory brake pads? Yes, Girodisc rotors are designed to accept OEM pads with no modification required. Are they compatible with OEM PCCB systems? Yes, they replace PCCB rotors directly while maintaining stock brake bias and performance balance. Do these rotors make noise? No, anti-noise spring washers eliminate the rattling common to floating designs. Are they track-ready? Absolutely. Girodisc rotors are built to perform under extreme heat cycles on street or track. How are they sold? Sold and priced per pair. Upgrade your Porsche 997 GT3 or GT2 with Girodisc’s 380x34mm floating rotors for improved cooling, reduced fade, and race-proven durability—perfect for both spirited street driving and competitive track use.

Girodisc Porsche 996, 997.1 Carrera Rear Rotors (Includes Spacers & Bolts) Boost the braking performance of your Porsche 996 or 997.1 Carrera with Girodisc’s lightweight two-piece rear rotors. This kit includes all necessary spacers and hardware, allowing a direct OEM installation while upgrading rotor diameter from 298mm to 325mm—improving cooling, braking leverage, and overall stopping consistency. Vehicle Fitment Porsche 996 Carrera / Carrera 4 / Carrera 4SPorsche 997.1 Carrera / Carrera SIncludes caliper spacers and bolts for installationDirect replacement – compatible with factory calipers and hardware Engineered for Porsche Precision The Girodisc system replaces the factory rotor with a larger, two-piece floating design engineered for performance and longevity. Each assembly pairs a CNC-machined 6061-T6 aluminum hat with Girodisc’s proprietary cast-iron friction rings, both made in the USA. The curved internal vane structure acts as a centrifugal pump, forcing air through the rotor for enhanced cooling. With its increased rotor size and floating design, this upgrade delivers superior heat management and more consistent braking under repeated high-speed stops. Features • Direct OEM replacement – includes spacers and bolts• Increases rotor diameter from 298mm to 325mm• 6061-T6 billet aluminum hats, machined and anodized in the USA• Proprietary cast-iron friction rings poured and finished in-house• Floating mount design with cadmium-plated steel drive pins• Anti-noise spring washers eliminate rattle and manage heat expansion• Curved internal vane design maximizes airflow and cooling• Reduces unsprung and rotational mass for sharper handling• Maintains factory brake bias and ABS calibration• Fully rebuildable – replace only friction rings when needed• Sold/priced per pair Girodisc A2-033 Rear Rotor FAQs: Why is this rotor larger than stock? The Girodisc system increases diameter to 325mm, providing greater mechanical leverage and improved heat capacity for stronger, more consistent braking. Do I need to modify my calipers to fit these? No. The kit includes custom spacers and bolts that perfectly reposition the calipers for the larger rotors—no cutting or permanent changes required. Will these affect brake bias or ABS? Not at all. Girodisc engineers each system to maintain the factory balance and ABS performance while increasing cooling efficiency. Are they suitable for track or aggressive driving? Absolutely. The curved vane design and floating assembly deliver exceptional fade resistance and durability, making them ideal for spirited street or track use. Upgrade your Porsche’s stopping power with Girodisc rear rotors—engineered to bring race-level precision and confidence to your 996 or 997.1 Carrera.

AP Racing J Hook 350x28mm Replacement Rear Brake Rotor Rings This kit is two replacement rotor discs and new installation hardware only. Center hats are not included. Replacement rotor rings for AP Racing 13.01.20014. Fits The Following Cars (w/ OEM iron rotors): Porsche 992 911 S/4S/GTS Porsche 991 911 S/4S/GTS Sold/priced per pair of rotor rings (including hardware). AP Racing J Hook Brake Rotors – The Gold Standard in Track Day & Racing Performance Engineered for professional motorsport, HPDE, and dedicated track day use, AP Racing’s J Hook Brake Rotors deliver uncompromising performance, thermal stability, and consistent braking power. These two-piece, floating rotors are built to handle the extreme demands of road racing, with design features derived from over 50 years of elite competition—including Formula 1, NASCAR, and IMSA. Unlike conventional one-piece rotors, AP Racing’s two-piece floating design features a billet aluminum hat mated to a cast iron disc via precision-engineered bobbins. This setup allows for controlled radial expansion under high heat, minimizing distortion and coning. The result? More even pad wear, a firmer pedal feel, and longer component life, even during extended lapping sessions or endurance racing. Floating hardware includes anti-knockback spring clips that reduce piston retraction while eliminating common NVH issues like rattling. Why Choose AP Racing J Hook Rotors? Advanced Cooling, Superior Bite, Unmatched Durability At the heart of every rotor is AP Racing’s proprietary high-carbon iron alloy, developed to withstand repeated thermal cycling without cracking or warping. Internally, directional vanes—far superior to OEM pillar or straight vane designs—maximize airflow and cooling. With 60 to 84 vanes per rotor, AP Racing achieves faster heat evacuation, reduced brake fade, and a more consistent friction surface. These rotors are left/right-specific for optimal airflow and balance. The exclusive J Hook slot pattern offers enhanced initial bite and promotes uniform heat distribution across the rotor face, reducing pad deposits and vibration. Unlike drilled rotors or straight-slot competitors, the J Hook design provides cleaner pad transfer during bed-in and superior modulation under braking—ideal for serious drivers who demand feedback and control. Yes, you might hear a little more whirr, but you’ll gain the stopping power, consistency, and longevity your lap times demand. Premium Components, Affordable Performance The rotor hats are CNC-machined from 6061-T6 billet aluminum and hard anodized for strength and heat resistance. Scalloped edges under the hat further assist heat dissipation. All hardware is U.S.-made to AP Racing spec, the same quality found on pro-level racing platforms. And while these rotors are race-proven, they’re also surprisingly cost-effective to replace. Don’t settle for cheap rotors that crack after a weekend—AP’s J Hook rings offer better durability and real long-term value. Fewer replacements mean more track time, less downtime, and peace of mind knowing you're running the best. Used by Champions. Trusted by Experts. From endurance racers to HPDE enthusiasts, AP Racing brake rotors are trusted worldwide for their reliability, longevity, and performance under pressure. Whether you're shaving seconds off your lap time or building a dedicated track car, the J Hook delivers a professional-grade solution that won’t let you down. AP Racing J Hook Brake Rotors for Auto Racing, Track Days & HPDE Why Rotor Design Matters: Heat Expansion and Floating Technology As with most metals, iron brake discs expand significantly under heat. When temperatures rise, the disc grows radially—expanding in both diameter and circumference. Traditional one-piece rotors struggle to accommodate this natural expansion. As the outer edge pulls away from the center under heat stress, it creates a condition called “coning”—a distortion that compromises pad-to-rotor contact. This distortion can lead to uneven pad wear, brake tapering, and an inconsistent, long brake pedal. AP Racing two-piece floating brake rotors are purpose-built to eliminate these issues. Engineered with “float” built into the disc or hat assembly, these rotors feature oblong-shaped mounting holes that allow the hardware to slide as the disc heats up. This flexibility ensures the disc runs true within the caliper under high-temperature loads, effectively reducing distortion, minimizing pad taper and stress cracks, and promoting longer component life. Custom Mounting Hardware & Anti-Knockback Spring Clips AP Racing rotors utilize application-specific, U.S.-made mounting hardware—not generic bolts. These premium components are the exact parts used in AP’s professional motorsport products, engineered to withstand the rigors of competitive racing. To manage lateral disc motion that can push caliper pistons backward (known as knockback), AP Racing integrates anti-knockback spring clips on alternating bobbins—five on a ten-bolt setup, six on a twelve-bolt disc. These clips keep the aluminum hat and iron disc ring properly aligned while still allowing for radial float. Bonus: they eliminate annoying rattles and vibrations, ensuring a quieter, more refined braking experience. High-Performance Hat Design for Heat Isolation The disc hats in AP Racing’s two-piece floating rotors are CNC-machined from 6061-T6 billet aluminum and finished with a hard anodized coating. This high-strength aluminum alloy was selected for its ability to maintain structural integrity even at elevated temperatures. AP adds scalloped channels beneath the hat to further encourage airflow and heat evacuation from the outer disc face, minimizing thermal transfer to hubs and wheel bearings—helping reduce maintenance costs on these expensive components. Internal Vane Engineering: Airflow Optimization & Thermal Stability AP Racing’s internal vane design sets them apart from OEM and most aftermarket competitors. While many factory brake discs use non-directional pillar vanes (low-cost and NVH-focused), AP Racing rotors use directional vanes engineered for maximum airflow. These rotors are side-specific—meaning you’ll receive a unique left and right disc in each set—ensuring optimized cooling through strategic vane orientation and shape. Beyond that, AP Racing rotors feature a superior vane count, typically ranging from 60 to 84 vanes, compared to 30–48 in most aftermarket rotors. After extensive CFD and thermal analysis, this high vane count was proven to: Increase airspeed and thermal transfer Reduce recirculation and deflection at the disc face Minimize coning, cracking, and brake fade Deliver more even pad contact and extended rotor life J Hook Slot Pattern: Exclusive to AP Racing Slots and drill holes may improve initial bite, but they also introduce “cool spots” in the rotor face—areas of uneven heating that can lead to stress risers, cracks, and pad vibration. OEM rotors often avoid this by leaving the disc face blank, but that compromises bite and brake feel. AP Racing’s patented J Hook design, developed through rigorous R&D, solves this problem. The hooks are meticulously spaced around the disc’s circumference and from hat to edge, forming a continuous distortion path that ensures even heat distribution. This encourages uniform pad deposits during bed-in, helps reduce judder and cracking, and improves consistency under repeated high-load braking. In addition, the J Hook slots provide more leading edges for pads to grip than traditional curved slots or blank rotors. While this might generate a mild whirring sound during braking, the benefits—more bite, cleaner bedding, better pedal feel—make it the top choice for committed racers and serious track day drivers. Metallurgy Backed by 50+ Years of Motorsport Leadership AP Racing's reputation is built on performance, and their proprietary iron alloy used in J Hook rotors is no exception. Drawing from over five decades of elite motorsport experience, including 750+ Formula 1 wins and widespread use across NASCAR, AP’s engineers have developed a disc alloy that excels under sustained racing temperatures and stress. Where OEM discs focus on affordability and mass production, AP Racing’s J Hook rotors are purpose-built for motorsport durability and heat resistance. Affordable Replacement Cost: Serious Value for Serious Drivers Even the best brake rotors are consumables. When you drive hard—especially at the track—your discs will eventually wear out. That’s why AP Racing designed their replacement iron rings to be cost-effective, allowing you to replace worn parts without breaking the bank. Compare that to constantly buying cheap $150 rotors every weekend—rotors that can't handle the heat and need to be swapped frequently. With AP Racing’s J Hook rotors, you get longer service intervals, less downtime, and better performance over time, making them an incredibly smart long-term investment. Proven on Track. Trusted by Champions. Top-tier racing teams rely on AP Racing J Hook rotors for one reason: they perform under pressure. Whether you're running time trials, attending HPDE events, or competing in wheel-to-wheel racing, these rotors offer professional-grade reliability, safety, and performance. Bedding and Preparation of AP Racing J Hook Discs Properly preparing your new brake discs before heavy use is extremely important. The goal of bedding-in your brake pads and discs is to mate them together properly and prepare them for heavy use.  When prepared properly, or bed-in, your pads will transfer a thin layer of material to the disc face (transfer layer).  The pads in your caliper will then actually ride on that thin layer of pad material you’ve put down on the rotor, rather than rubbing directly on the iron rotor face.  A good transfer layer is going to give you superior brake pedal feel, less noise, superior pad wear, and lower the chances of cracking your discs. Important Notes- PLEASE READ! First, make sure you are on a closed course to perform a proper bed-in.  Do NOT perform the procedure on public roads.  You need a stretch of asphalt with long straights, good visibility, and no potential obstructions.  Make sure you are in a position to safely and repeatedly attain the necessary speeds to perform the bed-in procedure.  A controlled racetrack is the best place to perform this procedure.  AP Racing and Competition Motorsport in no way suggest or condone speeding on public roads or breaking the law in your car, nor do we take responsibility for any damage or injury that occurs as a result of using our product or these procedures.  You are performing the bed-in procedure at your own risk.  During these procedures, it’s critical that you never come to a complete stop with your foot on the brake pedal.  If you have brake ducts on your car, you may want to block them off to allow your brake system to heat up easily. The procedure outlined below is a generic procedure for most types of mild race pad.  Please check your pad manufacturer’s recommended bed-in procedure. Accelerate to approximately 60mph and then decelerate down to 5 mph.  If your car has ABS, you should try to hold the brakes at a point just before ABS intervention.  Once the car slows to 5mph, immediately accelerate back up to about 60mph, and brake again to roughly 5mph.  Repeat this series of stopping and accelerating 8 to 10 times.  Again, do not come to a complete stop with your foot on the brake pedal. Cool the brake system down by cruising at 45mph+ for 5 to 10 minutes. Visually inspect your discs.  They should be a blue/grey color (instead of shiny silver), and have an even layer of pad material across and around the entire rotor face. If the AP Racing rotors don’t have a layer of pad material on them, perform another series of stops in the manner outlined above.

AP Racing J Hook 350x34mm Replacement Front Brake Rotor Rings This kit is two replacement rotor discs and new installation hardware only. Center hats are not included. Replacement rotor rings for AP Racing 13.01.20012. Fits The Following Cars (w/ OEM iron rotors): Porsche 992 911 S/4S/GTS Porsche 991 911 S/4S/GTS Sold/priced per pair of rotor rings (including hardware). AP Racing J Hook Brake Rotors – The Gold Standard in Track Day & Racing Performance Engineered for professional motorsport, HPDE, and dedicated track day use, AP Racing’s J Hook Brake Rotors deliver uncompromising performance, thermal stability, and consistent braking power. These two-piece, floating rotors are built to handle the extreme demands of road racing, with design features derived from over 50 years of elite competition—including Formula 1, NASCAR, and IMSA. Unlike conventional one-piece rotors, AP Racing’s two-piece floating design features a billet aluminum hat mated to a cast iron disc via precision-engineered bobbins. This setup allows for controlled radial expansion under high heat, minimizing distortion and coning. The result? More even pad wear, a firmer pedal feel, and longer component life, even during extended lapping sessions or endurance racing. Floating hardware includes anti-knockback spring clips that reduce piston retraction while eliminating common NVH issues like rattling. Why Choose AP Racing J Hook Rotors? Advanced Cooling, Superior Bite, Unmatched Durability At the heart of every rotor is AP Racing’s proprietary high-carbon iron alloy, developed to withstand repeated thermal cycling without cracking or warping. Internally, directional vanes—far superior to OEM pillar or straight vane designs—maximize airflow and cooling. With 60 to 84 vanes per rotor, AP Racing achieves faster heat evacuation, reduced brake fade, and a more consistent friction surface. These rotors are left/right-specific for optimal airflow and balance. The exclusive J Hook slot pattern offers enhanced initial bite and promotes uniform heat distribution across the rotor face, reducing pad deposits and vibration. Unlike drilled rotors or straight-slot competitors, the J Hook design provides cleaner pad transfer during bed-in and superior modulation under braking—ideal for serious drivers who demand feedback and control. Yes, you might hear a little more whirr, but you’ll gain the stopping power, consistency, and longevity your lap times demand. Premium Components, Affordable Performance The rotor hats are CNC-machined from 6061-T6 billet aluminum and hard anodized for strength and heat resistance. Scalloped edges under the hat further assist heat dissipation. All hardware is U.S.-made to AP Racing spec, the same quality found on pro-level racing platforms. And while these rotors are race-proven, they’re also surprisingly cost-effective to replace. Don’t settle for cheap rotors that crack after a weekend—AP’s J Hook rings offer better durability and real long-term value. Fewer replacements mean more track time, less downtime, and peace of mind knowing you're running the best. Used by Champions. Trusted by Experts. From endurance racers to HPDE enthusiasts, AP Racing brake rotors are trusted worldwide for their reliability, longevity, and performance under pressure. Whether you're shaving seconds off your lap time or building a dedicated track car, the J Hook delivers a professional-grade solution that won’t let you down. AP Racing J Hook Brake Rotors for Auto Racing, Track Days & HPDE Why Rotor Design Matters: Heat Expansion and Floating Technology As with most metals, iron brake discs expand significantly under heat. When temperatures rise, the disc grows radially—expanding in both diameter and circumference. Traditional one-piece rotors struggle to accommodate this natural expansion. As the outer edge pulls away from the center under heat stress, it creates a condition called “coning”—a distortion that compromises pad-to-rotor contact. This distortion can lead to uneven pad wear, brake tapering, and an inconsistent, long brake pedal. AP Racing two-piece floating brake rotors are purpose-built to eliminate these issues. Engineered with “float” built into the disc or hat assembly, these rotors feature oblong-shaped mounting holes that allow the hardware to slide as the disc heats up. This flexibility ensures the disc runs true within the caliper under high-temperature loads, effectively reducing distortion, minimizing pad taper and stress cracks, and promoting longer component life. Custom Mounting Hardware & Anti-Knockback Spring Clips AP Racing rotors utilize application-specific, U.S.-made mounting hardware—not generic bolts. These premium components are the exact parts used in AP’s professional motorsport products, engineered to withstand the rigors of competitive racing. To manage lateral disc motion that can push caliper pistons backward (known as knockback), AP Racing integrates anti-knockback spring clips on alternating bobbins—five on a ten-bolt setup, six on a twelve-bolt disc. These clips keep the aluminum hat and iron disc ring properly aligned while still allowing for radial float. Bonus: they eliminate annoying rattles and vibrations, ensuring a quieter, more refined braking experience. High-Performance Hat Design for Heat Isolation The disc hats in AP Racing’s two-piece floating rotors are CNC-machined from 6061-T6 billet aluminum and finished with a hard anodized coating. This high-strength aluminum alloy was selected for its ability to maintain structural integrity even at elevated temperatures. AP adds scalloped channels beneath the hat to further encourage airflow and heat evacuation from the outer disc face, minimizing thermal transfer to hubs and wheel bearings—helping reduce maintenance costs on these expensive components. Internal Vane Engineering: Airflow Optimization & Thermal Stability AP Racing’s internal vane design sets them apart from OEM and most aftermarket competitors. While many factory brake discs use non-directional pillar vanes (low-cost and NVH-focused), AP Racing rotors use directional vanes engineered for maximum airflow. These rotors are side-specific—meaning you’ll receive a unique left and right disc in each set—ensuring optimized cooling through strategic vane orientation and shape. Beyond that, AP Racing rotors feature a superior vane count, typically ranging from 60 to 84 vanes, compared to 30–48 in most aftermarket rotors. After extensive CFD and thermal analysis, this high vane count was proven to: Increase airspeed and thermal transfer Reduce recirculation and deflection at the disc face Minimize coning, cracking, and brake fade Deliver more even pad contact and extended rotor life J Hook Slot Pattern: Exclusive to AP Racing Slots and drill holes may improve initial bite, but they also introduce “cool spots” in the rotor face—areas of uneven heating that can lead to stress risers, cracks, and pad vibration. OEM rotors often avoid this by leaving the disc face blank, but that compromises bite and brake feel. AP Racing’s patented J Hook design, developed through rigorous R&D, solves this problem. The hooks are meticulously spaced around the disc’s circumference and from hat to edge, forming a continuous distortion path that ensures even heat distribution. This encourages uniform pad deposits during bed-in, helps reduce judder and cracking, and improves consistency under repeated high-load braking. In addition, the J Hook slots provide more leading edges for pads to grip than traditional curved slots or blank rotors. While this might generate a mild whirring sound during braking, the benefits—more bite, cleaner bedding, better pedal feel—make it the top choice for committed racers and serious track day drivers. Metallurgy Backed by 50+ Years of Motorsport Leadership AP Racing's reputation is built on performance, and their proprietary iron alloy used in J Hook rotors is no exception. Drawing from over five decades of elite motorsport experience, including 750+ Formula 1 wins and widespread use across NASCAR, AP’s engineers have developed a disc alloy that excels under sustained racing temperatures and stress. Where OEM discs focus on affordability and mass production, AP Racing’s J Hook rotors are purpose-built for motorsport durability and heat resistance. Affordable Replacement Cost: Serious Value for Serious Drivers Even the best brake rotors are consumables. When you drive hard—especially at the track—your discs will eventually wear out. That’s why AP Racing designed their replacement iron rings to be cost-effective, allowing you to replace worn parts without breaking the bank. Compare that to constantly buying cheap $150 rotors every weekend—rotors that can't handle the heat and need to be swapped frequently. With AP Racing’s J Hook rotors, you get longer service intervals, less downtime, and better performance over time, making them an incredibly smart long-term investment. Proven on Track. Trusted by Champions. Top-tier racing teams rely on AP Racing J Hook rotors for one reason: they perform under pressure. Whether you're running time trials, attending HPDE events, or competing in wheel-to-wheel racing, these rotors offer professional-grade reliability, safety, and performance. Bedding and Preparation of AP Racing J Hook Discs Properly preparing your new brake discs before heavy use is extremely important. The goal of bedding-in your brake pads and discs is to mate them together properly and prepare them for heavy use.  When prepared properly, or bed-in, your pads will transfer a thin layer of material to the disc face (transfer layer).  The pads in your caliper will then actually ride on that thin layer of pad material you’ve put down on the rotor, rather than rubbing directly on the iron rotor face.  A good transfer layer is going to give you superior brake pedal feel, less noise, superior pad wear, and lower the chances of cracking your discs. Important Notes- PLEASE READ! First, make sure you are on a closed course to perform a proper bed-in.  Do NOT perform the procedure on public roads.  You need a stretch of asphalt with long straights, good visibility, and no potential obstructions.  Make sure you are in a position to safely and repeatedly attain the necessary speeds to perform the bed-in procedure.  A controlled racetrack is the best place to perform this procedure.  AP Racing and Competition Motorsport in no way suggest or condone speeding on public roads or breaking the law in your car, nor do we take responsibility for any damage or injury that occurs as a result of using our product or these procedures.  You are performing the bed-in procedure at your own risk.  During these procedures, it’s critical that you never come to a complete stop with your foot on the brake pedal.  If you have brake ducts on your car, you may want to block them off to allow your brake system to heat up easily. The procedure outlined below is a generic procedure for most types of mild race pad.  Please check your pad manufacturer’s recommended bed-in procedure. Accelerate to approximately 60mph and then decelerate down to 5 mph.  If your car has ABS, you should try to hold the brakes at a point just before ABS intervention.  Once the car slows to 5mph, immediately accelerate back up to about 60mph, and brake again to roughly 5mph.  Repeat this series of stopping and accelerating 8 to 10 times.  Again, do not come to a complete stop with your foot on the brake pedal. Cool the brake system down by cruising at 45mph+ for 5 to 10 minutes. Visually inspect your discs.  They should be a blue/grey color (instead of shiny silver), and have an even layer of pad material across and around the entire rotor face. If the AP Racing rotors don’t have a layer of pad material on them, perform another series of stops in the manner outlined above.

Girodisc Porsche 992 GT3 Front Replacement Rings Refresh your Porsche’s braking power with Girodisc D1-272 front replacement rings. Designed as direct replacements for Girodisc two-piece rotors, these precision-engineered 408mm rings restore peak performance and cooling efficiency, ensuring consistent brake feel and reduced fade during aggressive driving or track use. Vehicle Fitment Compatible with:• 2022–2025 Porsche 911 GT3 (992)• 2023–2025 Porsche 911 GT3 Touring (992)• 2023–2025 Porsche 718 Cayman GT4 RS• 2023–2025 Porsche 718 Spyder RSNote: These are friction rings only. They attach to existing Girodisc aluminum hats using the supplied floating hardware kit. Race-Proven Engineering and Cooling Efficiency Girodisc rotor rings are cast in the USA from a proprietary high-carbon iron alloy designed to withstand extreme heat and repeated high-speed stops. The 72 curved internal vanes act as centrifugal pumps, pulling cool air through the disc to regulate temperature and resist fade. These rings deliver precise pedal modulation and exceptional longevity on both road and track. Features • Direct replacements for Girodisc 408mm front rotors• Fits Porsche 992 GT3, GT3 Touring, GT4 RS, and Spyder RS• High-carbon cast iron construction for superior durability• Directional curved vane design for maximum cooling• Fully machined, balanced, and finished in the USA• Includes new floating hardware kit• Sold/priced per pair Specifications • Diameter: 408mm• Position: Front• Material: High-carbon cast iron• Includes: Two rotor rings and full hardware kit• Made in the USA• Sold/priced per pair Girodisc D1-272 Replacement Ring FAQs Are these compatible with OEM Porsche rotors? No. These replacement rings are designed exclusively for Girodisc two-piece rotor systems and will not fit OEM or PCCB assemblies. Do they include new hardware? Yes. Each set comes complete with floating drive pins, washers, and bolts for secure, straightforward installation. Are they suitable for track use? Absolutely. Girodisc rotors are engineered for endurance racing, offering consistent brake feel even under prolonged high temperatures. When should I replace the rings? Replace them once they reach minimum thickness or if surface cracking extends to the edge of the disc. Rebuild your Porsche’s braking system with Girodisc D1-272 front replacement rings — precision-built, track-proven, and proudly made in the USA.

Girodisc 350mm Porsche 996 / 991 / 992 Rear Rotors (with Spacers & Bolts) The Girodisc A2-032B Rear Rotor Kit is a premium direct-fit replacement for Porsche 996, 991, and 992 models. Engineered for high-performance driving, this system includes caliper spacers and longer bolts to accommodate the larger 350mm rotors. The result is improved braking torque, enhanced cooling efficiency, and reduced unsprung mass—all while retaining factory fitment and ABS calibration. Lightweight Design & Increased Performance Each Girodisc rotor assembly pairs a CNC-machined 6061-T6 aluminum hat with a proprietary cast iron disc. The 2-piece design significantly reduces rotational mass compared to OEM rotors, improving suspension response and acceleration. The curved vane design acts as a centrifugal pump, drawing air through the rotor to enhance cooling and resist fade under extreme braking conditions. Precision Floating Mount System The rotors feature Girodisc’s race-proven floating mount design with 10 cadmium-plated steel drive pins connecting the iron ring to the aluminum hat. These pins allow the disc to expand radially under high temperatures without warping, ensuring consistent pad contact. Anti-noise spring washers eliminate rattle, maintaining quiet operation suitable for street and track use alike. Girodisc A2-032B 350mm 2pc Porsche Rear Rotor Vehicle Fitment Porsche 996 Carrera / Carrera 4 / Carrera 4S Porsche 991 Carrera / Carrera 4 / Carrera GTS (Base models require S/4S/GTS rear pad shape for full rotor sweep) Porsche 992 Carrera / Carrera S / Carrera 4S Direct bolt-on installation with supplied spacers and hardware Technical Specifications CMS Number: A2-032B Position: Rear Rotor Diameter: 350mm (includes caliper spacers & longer bolts) Design: 2-piece floating rotor assembly Material: Proprietary cast iron with 6061-T6 aluminum hat Vane Design: Curved directional vanes for improved airflow Hardware: Cadmium-plated steel drive pins, class 12.9 screws, anti-noise washers Rebuildable: Yes — replace rotor rings, reuse aluminum hats Sold/Price: Per pair Girodisc A2-032B 350mm 2pc Porsche Rear Rotor FAQs Do these rotors fit all Porsche 996, 991, and 992 models? Yes. However, 991 base Carrera models must use the S/4S/GTS rear pad shape for full pad sweep. What is included with this kit? Each kit includes two 350mm rotors, caliper spacers, and longer mounting bolts for a complete direct installation. Are modifications required? No. The supplied hardware makes this a true bolt-on upgrade using factory calipers and lines. What are the main benefits over stock rotors? Improved cooling, reduced weight, better pedal response, and replaceable rings for long-term cost savings. Upgrade your Porsche’s braking system with the Girodisc A2-032B Rear Rotor Kit. Experience reduced fade, sharper braking response, and long-term durability whether on the street or at the track.

AP Racing Road 380mm Road Brake Kit for Porsche (Front) Fit The Following Cars Porsche 991 Carrera S/4S/GTS (PCCB and Iron Rotors) Porsche 992 Carrera Base / Carrera 4 (PCCB and Iron Rotors) Complete front AP Racing Road Brake Kit for Porsche 991 and 992 911 features; Features AP Racing Radi-Cal 9562 calipers. Available with Black, Red, or Silver Calipers Takes your brakes into GT3 territory with huge 380x36mm, 72 vane AP Racing J Hook discs Painted calipers with dust boots add durability in inclement weather conditions Low noise, vibration, and harshness for a very OE-like experience during daily driving Leverages six piston AP Racing CP9562 World Radi-CAL II calipers with a red, black, or silver painted finish Utilizes large volume brake pads for heat absorption and longevity Pistons sized properly to maintain proper brake bias and work with the OEM master cylinder and ABS system Designed to mate with OEM rear brakes or our matching rear AP Racing Road Brake Kit

AP Racing Radi-CAL 380mm Competition Brake Kit (Front) FIT The Following Cars Porsche 992.1 GT3 Cup Car Porsche 991.2 GT3 Cup Car Complete rear AP Racing Radi-CAL Competition Brake Kit. Fits the Porsche 991.2 and 992.1 GT3 Cup car. Complete front AP Racing by Essex Radi-CAL Competition Brake Kit for the Porsche 991.2 GT3 Cup (2017-2020): Eliminates the need to remove the caliper for pad changes Direct bolt-on to OE Porsche Motorsport 991.2 Cup uprights with included spacers AP Racing Radi-CAL CP9665 calipers with durable ventilated stainless steel pistons and anti-knockback springs Hard anodized caliper finish that is resistant to wear and deterioration at elevated temperatures 380mm x 32mm 2-piece floating 72-vane J Hook Discs with D54 radial depth Innovative spline drive system further mitigates knockback and offers highly consistent pedal effort Designed for: club racing, time trial, autocross, HPDE Every component designed to resist the heat of extended track sessions Works with standard OE master cylinder sizes Includes pad tension kit (eliminates noise) and disc burning at no additional cost Designed to work with Ap Racing front Brake Kit