Porsche Brake Rotors

AP Racing Radi-CAL 380mm Competition Brake Kit (Rear) Fit The Following Cars Porsche 992.1 GT3 Cup Car Porsche 991.2 GT3 Cup Car Complete rear AP Racing Radi-CAL Competition Brake Kit. Fits the Porsche 991.2 and 992.1 GT3 Cup car. Eliminates the need to remove the caliper for pad changes AP Racing Radi-CAL with durable ventilated stainless steel pistons and anti-knockback springs Hard anodized caliper finish that is resistant to wear and deterioration at elevated temperatures Large selection of brake pad options from all major pad manufacturers Fits OE 18" GT3 Cup wheels without a spacer 380x32mm, 72 vane AP Racing disc vs. only 48 cooling vanes in the OE disc Works with standard OE master cylinder sizes Every component designed to resist the heat of extended track sessions Designed for: club racing, time trial, autocross, HPDE Includes pad tension kit (eliminates noise) and disc burning at no additional cost Designed to work with Ap Racing front Brake Kit

AP Racing Radi-CAL 394mm Competition Brake Kit for Porsche GT4 (Front) Fit The Following Cars Porsche 981/718 GT4 (PCCB and Iron Rotors) Complete front AP Racing Radi-CAL Competition Brake Kit for the Porsche Cayman 981/718 GT4. Features AP Racing Radi-CAL 9669 calipers for extreme durability! Clears many popular 19" and 20" track wheels Durable, ventilated stainless steel pistons (no ceramic piston caps to break) with anti-knockback springs Design eliminates the need to remove caliper for pad changes Saves 10 unsprung lbs. vs. OEM iron brakes and very close in weight to the OEM PCCB system Allows for the preservation of pricey OEM brake components Huge array of brake pad options from all major pad manufacturers 394x34mm, 84 vane AP Racing J Hook Discs Every component designed to resist the heat of extended track sessions Pistons sized properly to allow for seamless integration with OEM master cylinder and ABS system Includes the AP Racing pad tension kit and disc burning at no additional cost Designed to work with OEM rear brakes or the AP Racing Rear Brake Kit

AP Racing Radi-CAL 380mm Competition Brake Kit GT4RS (Rear) Fit The Following Cars Porsche 718/982 GT4RS (PCCB and Iron Rotors) Complete rear AP Racing Radi-CAL Competition Brake Kit. Fits all variants of the Porsche 718/982 GT4RS. Eliminates the need to remove the caliper for pad changes Retains OEM parking brake functionality Saves 18 unsprung lbs. vs. OEM iron brakes and weighs almost the same as the OEM PCCB system Jewel-like ENP caliper finish is incredibly durable and easy to clean AP Racing Radi-CAL with durable, ventilated stainless steel pistons (no ceramic piston caps to break) with anti-knockback springs Allows for the preservation of pricey OEM brake components Huge array of brake pad options from all major pad manufacturers Fits OEM 20" wheels without spacer 380x32mm, 72 vane AP Racing disc fits inside popular 19" wheels Every component designed to resist the heat of extended track sessions Pistons sized properly to allow for seamless integration with OEM master cylinder and ABS system Includes pad tension kit (eliminates noise) and disc burning at no additional cost Designed to work with Ap Racing front Brake Kit

AP Racing Radi-CAL 394mm Competition Brake Kit (Front) Fit The Following Cars Porsche 991 GT2RS  Porsche 991 GT3  Porsche 991 GT3RS  Porsche 718 GT4RS Complete front AP Racing Radi-CAL Competition Brake Kit for the Porsche 991 GT3/3RS/2RS and Porsche Cayman 718 GT4 RS. Features AP Racing Radi-CAL 9669 calipers for extreme durability! Clears many popular 19" and 20" track wheels Durable, ventilated stainless steel pistons (no ceramic piston caps to break) with anti-knockback springs Design eliminates the need to remove caliper for pad changes Saves 10 unsprung lbs. vs. OEM iron brakes and very close in weight to the OEM PCCB system Allows for the preservation of pricey OEM brake components Huge array of brake pad options from all major pad manufacturers 394x34mm, 84 vane AP Racing J Hook Discs Every component designed to resist the heat of extended track sessions Pistons sized properly to allow for seamless integration with OEM master cylinder and ABS system Includes the AP Racing pad tension kit and disc burning at no additional cost Designed to work with OEM rear brakes or the AP Racing Rear Brake Kit

AP Racing J Hook 410x36mm Replacement Front Brake Rotor Rings This is a pair of replacement front rotor rings with new hardware included. Center hat is not included, this kit is rotor rings and hardware only. Replacement discs only for AP Racing 13.01.20025 and 13.01.20029 rotors. Fits the Following Cars (w/ OEM PCCB rotors): Porsche 991 GT2RS PCCB (Front) Porsche 991 GT3 PCCB (Front) Porsche 991 GT3RS PCCB (Front) Porsche 718 GT4 PCCB (Front) Porsche 991 911 Turbo/TurboS (Front) Sold/priced per pair of rotor rings with hardware. AP Racing J Hook Brake Rotors – The Gold Standard in Track Day & Racing Performance Engineered for professional motorsport, HPDE, and dedicated track day use, AP Racing’s J Hook Brake Rotors deliver uncompromising performance, thermal stability, and consistent braking power. These two-piece, floating rotors are built to handle the extreme demands of road racing, with design features derived from over 50 years of elite competition—including Formula 1, NASCAR, and IMSA. Unlike conventional one-piece rotors, AP Racing’s two-piece floating design features a billet aluminum hat mated to a cast iron disc via precision-engineered bobbins. This setup allows for controlled radial expansion under high heat, minimizing distortion and coning. The result? More even pad wear, a firmer pedal feel, and longer component life, even during extended lapping sessions or endurance racing. Floating hardware includes anti-knock back spring clips that reduce piston retraction while eliminating common NVH issues like rattling. Why Choose AP Racing J Hook Rotors? Advanced Cooling, Superior Bite, Unmatched Durability At the heart of every rotor is AP Racing’s proprietary high-carbon iron alloy, developed to withstand repeated thermal cycling without cracking or warping. Internally, directional vanes—far superior to OEM pillar or straight vane designs—maximize airflow and cooling. With 60 to 84 vanes per rotor, AP Racing achieves faster heat evacuation, reduced brake fade, and a more consistent friction surface. These rotors are left/right-specific for optimal airflow and balance. The exclusive J Hook slot pattern offers enhanced initial bite and promotes uniform heat distribution across the rotor face, reducing pad deposits and vibration. Unlike drilled rotors or straight-slot competitors, the J Hook design provides cleaner pad transfer during bed-in and superior modulation under braking—ideal for serious drivers who demand feedback and control. Yes, you might hear a little more whirr, but you’ll gain the stopping power, consistency, and longevity your lap times demand. Premium Components, Affordable Performance The rotor hats are CNC-machined from 6061-T6 billet aluminum and hard anodized for strength and heat resistance. Scalloped edges under the hat further assist heat dissipation. All hardware is U.S.-made to AP Racing spec, the same quality found on pro-level racing platforms. And while these rotors are race-proven, they’re also surprisingly cost-effective to replace. Don’t settle for cheap rotors that crack after a weekend—AP’s J Hook rings offer better durability and real long-term value. Fewer replacements mean more track time, less downtime, and peace of mind knowing you're running the best. Used by Champions. Trusted by Experts. From endurance racers to HPDE enthusiasts, AP Racing brake rotors are trusted worldwide for their reliability, longevity, and performance under pressure. Whether you're shaving seconds off your lap time or building a dedicated track car, the J Hook delivers a professional-grade solution that won’t let you down. AP Racing by Essex 2-piece Competition J Hook front iron disc pair for 991 GT3/RS and 718 GT4/Spyder RS to replace PCCB discs. 410x36mm (16.14" x 1.40") Huge increase in airflow, cooling capacity, and durability vs. OEM PCCB discs Drastically less expense long-term running costs vs. PCCB Must use the standard front 991 GT3/RS pad shape used in the OEM iron rotors system Not compatible with OEM PCCB pad shape Over twice as many internal cooling vanes as the OEM PCCB's Weighs almost the same as the OEM 380x34mm iron discs, despite much larger size Designed for: club racing, time trial, auto-x, HPDE Works with OEM calipers and wheels, no modifications required Ultralight, fully floating, anodized billet aluminum hat with float control/anti-rattle clips AP Racing J Hook Brake Rotors for Auto Racing, Track Days & HPDE Why Rotor Design Matters: Heat Expansion and Floating Technology As with most metals, iron brake discs expand significantly under heat. When temperatures rise, the disc grows radially—expanding in both diameter and circumference. Traditional one-piece rotors struggle to accommodate this natural expansion. As the outer edge pulls away from the center under heat stress, it creates a condition called “coning”—a distortion that compromises pad-to-rotor contact. This distortion can lead to uneven pad wear, brake tapering, and an inconsistent, long brake pedal. AP Racing two-piece floating brake rotors are purpose-built to eliminate these issues. Engineered with “float” built into the disc or hat assembly, these rotors feature oblong-shaped mounting holes that allow the hardware to slide as the disc heats up. This flexibility ensures the disc runs true within the caliper under high-temperature loads, effectively reducing distortion, minimizing pad taper and stress cracks, and promoting longer component life. Custom Mounting Hardware & Anti-Knock Back Spring Clips AP Racing rotors utilize application-specific, U.S.-made mounting hardware—not generic bolts. These premium components are the exact parts used in AP’s professional motorsport products, engineered to withstand the rigors of competitive racing. To manage lateral disc motion that can push caliper pistons backward (known as knock back), AP Racing integrates anti-knock back spring clips on alternating bobbins—five on a ten-bolt setup, six on a twelve-bolt disc. These clips keep the aluminum hat and iron disc ring properly aligned while still allowing for radial float. Bonus: they eliminate annoying rattles and vibrations, ensuring a quieter, more refined braking experience. High-Performance Hat Design for Heat Isolation The disc hats in AP Racing’s two-piece floating rotors are CNC-machined from 6061-T6 billet aluminum and finished with a hard anodized coating. This high-strength aluminum alloy was selected for its ability to maintain structural integrity even at elevated temperatures. AP adds scalloped channels beneath the hat to further encourage airflow and heat evacuation from the outer disc face, minimizing thermal transfer to hubs and wheel bearings—helping reduce maintenance costs on these expensive components. Internal Vane Engineering: Airflow Optimization & Thermal Stability AP Racing’s internal vane design sets them apart from OEM and most aftermarket competitors. While many factory brake discs use non-directional pillar vanes (low-cost and NVH-focused), AP Racing rotors use directional vanes engineered for maximum airflow. These rotors are side-specific—meaning you’ll receive a unique left and right disc in each set—ensuring optimized cooling through strategic vane orientation and shape. Beyond that, AP Racing rotors feature a superior vane count, typically ranging from 60 to 84 vanes, compared to 30–48 in most aftermarket rotors. After extensive CFD and thermal analysis, this high vane count was proven to: Increase airspeed and thermal transfer Reduce recirculation and deflection at the disc face Minimize coning, cracking, and brake fade Deliver more even pad contact and extended rotor life J Hook Slot Pattern: Exclusive to AP Racing Slots and drill holes may improve initial bite, but they also introduce “cool spots” in the rotor face—areas of uneven heating that can lead to stress risers, cracks, and pad vibration. OEM rotors often avoid this by leaving the disc face blank, but that compromises bite and brake feel. AP Racing’s patented J Hook design, developed through rigorous R&D, solves this problem. The hooks are meticulously spaced around the disc’s circumference and from hat to edge, forming a continuous distortion path that ensures even heat distribution. This encourages uniform pad deposits during bed-in, helps reduce judder and cracking, and improves consistency under repeated high-load braking. In addition, the J Hook slots provide more leading edges for pads to grip than traditional curved slots or blank rotors. While this might generate a mild whirring sound during braking, the benefits—more bite, cleaner bedding, better pedal feel—make it the top choice for committed racers and serious track day drivers. Metallurgy Backed by 50+ Years of Motorsport Leadership AP Racing's reputation is built on performance, and their proprietary iron alloy used in J Hook rotors is no exception. Drawing from over five decades of elite motorsport experience, including 750+ Formula 1 wins and widespread use across NASCAR, AP’s engineers have developed a disc alloy that excels under sustained racing temperatures and stress. Where OEM discs focus on affordability and mass production, AP Racing’s J Hook rotors are purpose-built for motorsport durability and heat resistance. Affordable Replacement Cost: Serious Value for Serious Drivers Even the best brake rotors are consumables. When you drive hard—especially at the track—your discs will eventually wear out. That’s why AP Racing designed their replacement iron rings to be cost-effective, allowing you to replace worn parts without breaking the bank. Compare that to constantly buying cheap $150 rotors every weekend—rotors that can't handle the heat and need to be swapped frequently. With AP Racing’s J Hook rotors, you get longer service intervals, less downtime, and better performance over time, making them an incredibly smart long-term investment. Proven on Track. Trusted by Champions. Top-tier racing teams rely on AP Racing J Hook rotors for one reason: they perform under pressure. Whether you're running time trials, attending HPDE events, or competing in wheel-to-wheel racing, these rotors offer professional-grade reliability, safety, and performance. Bedding and Preparation of AP Racing J Hook Discs Properly preparing your new brake discs before heavy use is extremely important. The goal of bedding-in your brake pads and discs is to mate them together properly and prepare them for heavy use.  When prepared properly, or bed-in, your pads will transfer a thin layer of material to the disc face (transfer layer).  The pads in your caliper will then actually ride on that thin layer of pad material you’ve put down on the rotor, rather than rubbing directly on the iron rotor face.  A good transfer layer is going to give you superior brake pedal feel, less noise, superior pad wear, and lower the chances of cracking your discs. Important Notes- PLEASE READ! First, make sure you are on a closed course to perform a proper bed-in.  Do NOT perform the procedure on public roads.  You need a stretch of asphalt with long straights, good visibility, and no potential obstructions.  Make sure you are in a position to safely and repeatedly attain the necessary speeds to perform the bed-in procedure.  A controlled racetrack is the best place to perform this procedure.  AP Racing and Competition Motorsport in no way suggest or condone speeding on public roads or breaking the law in your car, nor do we take responsibility for any damage or injury that occurs as a result of using our product or these procedures.  You are performing the bed-in procedure at your own risk.  During these procedures, it’s critical that you never come to a complete stop with your foot on the brake pedal.  If you have brake ducts on your car, you may want to block them off to allow your brake system to heat up easily. The procedure outlined below is a generic procedure for most types of mild race pad.  Please check your pad manufacturer’s recommended bed-in procedure. Accelerate to approximately 60mph and then decelerate down to 5 mph.  If your car has ABS, you should try to hold the brakes at a point just before ABS intervention.  Once the car slows to 5mph, immediately accelerate back up to about 60mph, and brake again to roughly 5mph.  Repeat this series of stopping and accelerating 8 to 10 times.  Again, do not come to a complete stop with your foot on the brake pedal. Cool the brake system down by cruising at 45mph+ for 5 to 10 minutes. Visually inspect your discs.  They should be a blue/grey color (instead of shiny silver), and have an even layer of pad material across and around the entire rotor face. If the AP Racing rotors don’t have a layer of pad material on them, perform another series of stops in the manner outlined above.

AP Racing 410x36mm Two-Piece Front Floating Racing Brake Rotors Fit The Following Cars (w/ OEM PCCB Rotors) Porsche 991 GT2RS PCCB (Front) Porsche 991 GT3 PCCB (Front) Porsche 991 GT3RS PCCB (Front) Porsche 718 GT4RS/Spyder RS PCCB (Front) Sold/priced per pair. AP Racing by Essex 2-piece Competition J Hook front iron disc pair for 991 GT3/RS and 718 GT4RS / Spyder RS to replace PCCB discs. 410x36mm (16.14" x 1.40") Huge increase in airflow, cooling capacity, and durability vs. OEM PCCB discs Drastically less expense long-term running costs vs. PCCB Must use the standard front 991 GT3/RS pad shape used in OEM iron system (not compatible with OE PCCB pad shape) Over twice as many internal cooling vanes as the OEM PCCB's Weighs almost the same as the OEM 380x34mm iron discs, despite much larger size Designed for: club racing, time trial, auto-x, HPDE Works with OEM calipers and wheels, no modifications required Ultralight, fully floating, anodized billet aluminum hat with float control/anti-rattle clips AP Racing J Hook Brake Rotors – The Gold Standard in Track Day & Racing Performance Engineered for professional motorsport, HPDE, and dedicated track day use, AP Racing’s J Hook Brake Rotors deliver uncompromising performance, thermal stability, and consistent braking power. These two-piece, floating rotors are built to handle the extreme demands of road racing, with design features derived from over 50 years of elite competition—including Formula 1, NASCAR, and IMSA. Unlike conventional one-piece rotors, AP Racing’s two-piece floating design features a billet aluminum hat mated to a cast iron disc via precision-engineered bobbins. This setup allows for controlled radial expansion under high heat, minimizing distortion and coning. The result? More even pad wear, a firmer pedal feel, and longer component life, even during extended lapping sessions or endurance racing. Floating hardware includes anti-knockback spring clips that reduce piston retraction while eliminating common NVH issues like rattling. Why Choose AP Racing J Hook Rotors? Advanced Cooling, Superior Bite, Unmatched Durability At the heart of every rotor is AP Racing’s proprietary high-carbon iron alloy, developed to withstand repeated thermal cycling without cracking or warping. Internally, directional vanes—far superior to OEM pillar or straight vane designs—maximize airflow and cooling. With 60 to 84 vanes per rotor, AP Racing achieves faster heat evacuation, reduced brake fade, and a more consistent friction surface. These rotors are left/right-specific for optimal airflow and balance. The exclusive J Hook slot pattern offers enhanced initial bite and promotes uniform heat distribution across the rotor face, reducing pad deposits and vibration. Unlike drilled rotors or straight-slot competitors, the J Hook design provides cleaner pad transfer during bed-in and superior modulation under braking—ideal for serious drivers who demand feedback and control. Yes, you might hear a little more whirr, but you’ll gain the stopping power, consistency, and longevity your lap times demand. Premium Components, Affordable Performance The rotor hats are CNC-machined from 6061-T6 billet aluminum and hard anodized for strength and heat resistance. Scalloped edges under the hat further assist heat dissipation. All hardware is U.S.-made to AP Racing spec, the same quality found on pro-level racing platforms. And while these rotors are race-proven, they’re also surprisingly cost-effective to replace. Don’t settle for cheap rotors that crack after a weekend—AP’s J Hook rings offer better durability and real long-term value. Fewer replacements mean more track time, less downtime, and peace of mind knowing you're running the best. Used by Champions. Trusted by Experts. From endurance racers to HPDE enthusiasts, AP Racing brake rotors are trusted worldwide for their reliability, longevity, and performance under pressure. Whether you're shaving seconds off your lap time or building a dedicated track car, the J Hook delivers a professional-grade solution that won’t let you down.   AP Racing J Hook Brake Rotors for Auto Racing, Track Days & HPDE Why Rotor Design Matters: Heat Expansion and Floating Technology As with most metals, iron brake discs expand significantly under heat. When temperatures rise, the disc grows radially—expanding in both diameter and circumference. Traditional one-piece rotors struggle to accommodate this natural expansion. As the outer edge pulls away from the center under heat stress, it creates a condition called “coning”—a distortion that compromises pad-to-rotor contact. This distortion can lead to uneven pad wear, brake tapering, and an inconsistent, long brake pedal. AP Racing two-piece floating brake rotors are purpose-built to eliminate these issues. Engineered with “float” built into the disc or hat assembly, these rotors feature oblong-shaped mounting holes that allow the hardware to slide as the disc heats up. This flexibility ensures the disc runs true within the caliper under high-temperature loads, effectively reducing distortion, minimizing pad taper and stress cracks, and promoting longer component life. Custom Mounting Hardware & Anti-Knockback Spring Clips AP Racing rotors utilize application-specific, U.S.-made mounting hardware—not generic bolts. These premium components are the exact parts used in AP’s professional motorsport products, engineered to withstand the rigors of competitive racing. To manage lateral disc motion that can push caliper pistons backward (known as knockback), AP Racing integrates anti-knockback spring clips on alternating bobbins—five on a ten-bolt setup, six on a twelve-bolt disc. These clips keep the aluminum hat and iron disc ring properly aligned while still allowing for radial float. Bonus: they eliminate annoying rattles and vibrations, ensuring a quieter, more refined braking experience. High-Performance Hat Design for Heat Isolation The disc hats in AP Racing’s two-piece floating rotors are CNC-machined from 6061-T6 billet aluminum and finished with a hard anodized coating. This high-strength aluminum alloy was selected for its ability to maintain structural integrity even at elevated temperatures. AP adds scalloped channels beneath the hat to further encourage airflow and heat evacuation from the outer disc face, minimizing thermal transfer to hubs and wheel bearings—helping reduce maintenance costs on these expensive components. Internal Vane Engineering: Airflow Optimization & Thermal Stability AP Racing’s internal vane design sets them apart from OEM and most aftermarket competitors. While many factory brake discs use non-directional pillar vanes (low-cost and NVH-focused), AP Racing rotors use directional vanes engineered for maximum airflow. These rotors are side-specific—meaning you’ll receive a unique left and right disc in each set—ensuring optimized cooling through strategic vane orientation and shape. Beyond that, AP Racing rotors feature a superior vane count, typically ranging from 60 to 84 vanes, compared to 30–48 in most aftermarket rotors. After extensive CFD and thermal analysis, this high vane count was proven to: Increase airspeed and thermal transfer Reduce recirculation and deflection at the disc face Minimize coning, cracking, and brake fade Deliver more even pad contact and extended rotor life J Hook Slot Pattern: Exclusive to AP Racing Slots and drill holes may improve initial bite, but they also introduce “cool spots” in the rotor face—areas of uneven heating that can lead to stress risers, cracks, and pad vibration. OEM rotors often avoid this by leaving the disc face blank, but that compromises bite and brake feel. AP Racing’s patented J Hook design, developed through rigorous R&D, solves this problem. The hooks are meticulously spaced around the disc’s circumference and from hat to edge, forming a continuous distortion path that ensures even heat distribution. This encourages uniform pad deposits during bed-in, helps reduce judder and cracking, and improves consistency under repeated high-load braking. In addition, the J Hook slots provide more leading edges for pads to grip than traditional curved slots or blank rotors. While this might generate a mild whirring sound during braking, the benefits—more bite, cleaner bedding, better pedal feel—make it the top choice for committed racers and serious track day drivers. Metallurgy Backed by 50+ Years of Motorsport Leadership AP Racing's reputation is built on performance, and their proprietary iron alloy used in J Hook rotors is no exception. Drawing from over five decades of elite motorsport experience, including 750+ Formula 1 wins and widespread use across NASCAR, AP’s engineers have developed a disc alloy that excels under sustained racing temperatures and stress. Where OEM discs focus on affordability and mass production, AP Racing’s J Hook rotors are purpose-built for motorsport durability and heat resistance. Affordable Replacement Cost: Serious Value for Serious Drivers Even the best brake rotors are consumables. When you drive hard—especially at the track—your discs will eventually wear out. That’s why AP Racing designed their replacement iron rings to be cost-effective, allowing you to replace worn parts without breaking the bank. Compare that to constantly buying cheap $150 rotors every weekend—rotors that can't handle the heat and need to be swapped frequently. With AP Racing’s J Hook rotors, you get longer service intervals, less downtime, and better performance over time, making them an incredibly smart long-term investment. Proven on Track. Trusted by Champions. Top-tier racing teams rely on AP Racing J Hook rotors for one reason: they perform under pressure. Whether you're running time trials, attending HPDE events, or competing in wheel-to-wheel racing, these rotors offer professional-grade reliability, safety, and performance. Bedding and preparation of AP Racing J Hook Disc Properly preparing your new brake discs before heavy use is extremely important. The goal of bedding-in your brake pads and discs is to mate them together properly and prepare them for heavy use.  When prepared properly, or bed-in, your pads will transfer a thin layer of material to the disc face (transfer layer).  The pads in your caliper will then actually ride on that thin layer of pad material you’ve put down on the rotor, rather than rubbing directly on the iron rotor face.  A good transfer layer is going to give you superior brake pedal feel, less noise, superior pad wear, and lower the chances of cracking your discs. Important Notes- PLEASE READ! First, make sure you are on a closed course to perform a proper bed-in.  Do NOT perform the procedure on public roads.  You need a stretch of asphalt with long straights, good visibility, and no potential obstructions.  Make sure you are in a position to safely and repeatedly attain the necessary speeds to perform the bed-in procedure.  A controlled racetrack is the best place to perform this procedure.  AP Racing and Competition Motorsport in no way suggest or condone speeding on public roads or breaking the law in your car, nor do we take responsibility for any damage or injury that occurs as a result of using our product or these procedures.  You are performing the bed-in procedure at your own risk.  During these procedures, it’s critical that you never come to a complete stop with your foot on the brake pedal.  If you have brake ducts on your car, you may want to block them off to allow your brake system to heat up easily. The procedure outlined below is a generic procedure for most types of mild race pad.  Please check your pad manufacturer’s recommended bed-in procedure. Accelerate to approximately 60mph and then decelerate down to 5 mph.  If your car has ABS, you should try to hold the brakes at a point just before ABS intervention.  Once the car slows to 5mph, immediately accelerate back up to about 60mph, and brake again to roughly 5mph.  Repeat this series of stopping and accelerating 8 to 10 times.  Again, do not come to a complete stop with your foot on the brake pedal. Cool the brake system down by cruising at 45mph+ for 5 to 10 minutes. Visually inspect your discs.  They should be a blue/grey color (instead of shiny silver), and have an even layer of pad material across and around the entire rotor face. If the AP Racing rotors don’t have a layer of pad material on them, perform another series of stops in the manner outlined above.

AP Racing J Hook 390x32mm Replacement Rear Brake Rotor Rings This kit is two replacement rotor discs and associated installation hardware only. Center hat is not included. Replacement discs for AP Racing 13.01.20026. Fits The Following Cars (w/ OEM PCCB rotors): Porsche 992 GT3 (Rear) Porsche 992 GT3RS (Rear) Porsche 718/982 GT4RS (Rear) Porsche 991 GT2RS/GT3/GT3RS (Rear) Porsche 981 GT4 (Rear) Porsche 991 911 Turbo/TurboS (Rear) Sold/priced per pair of rotor rings (including hardware). 390x32mm (15.35" x 1.25") 72-vane, D66, J Hook Iron Racing Brake Disc Replacements AP Racing J Hook Brake Rotors – The Gold Standard in Track Day & Racing Performance >Engineered for professional motorsport, HPDE, and dedicated track day use, AP Racing’s J Hook Brake Rotors deliver uncompromising performance, thermal stability, and consistent braking power. These two-piece, floating rotors are built to handle the extreme demands of road racing, with design features derived from over 50 years of elite competition—including Formula 1, NASCAR, and IMSA. Unlike conventional one-piece rotors, AP Racing’s two-piece floating design features a billet aluminum hat mated to a cast iron disc via precision-engineered bobbins. This setup allows for controlled radial expansion under high heat, minimizing distortion and coning. The result? More even pad wear, a firmer pedal feel, and longer component life, even during extended lapping sessions or endurance racing. Floating hardware includes anti-knockback spring clips that reduce piston retraction while eliminating common NVH issues like rattling. Why Choose AP Racing J Hook Rotors? Advanced Cooling, Superior Bite, Unmatched Durability At the heart of every rotor is AP Racing’s proprietary high-carbon iron alloy, developed to withstand repeated thermal cycling without cracking or warping. Internally, directional vanes—far superior to OEM pillar or straight vane designs—maximize airflow and cooling. With 60 to 84 vanes per rotor, AP Racing achieves faster heat evacuation, reduced brake fade, and a more consistent friction surface. These rotors are left/right-specific for optimal airflow and balance. The exclusive J Hook slot pattern offers enhanced initial bite and promotes uniform heat distribution across the rotor face, reducing pad deposits and vibration. Unlike drilled rotors or straight-slot competitors, the J Hook design provides cleaner pad transfer during bed-in and superior modulation under braking—ideal for serious drivers who demand feedback and control. Yes, you might hear a little more whirr, but you’ll gain the stopping power, consistency, and longevity your lap times demand. Premium Components, Affordable Performance The rotor hats are CNC-machined from 6061-T6 billet aluminum and hard anodized for strength and heat resistance. Scalloped edges under the hat further assist heat dissipation. All hardware is U.S.-made to AP Racing spec, the same quality found on pro-level racing platforms. And while these rotors are race-proven, they’re also surprisingly cost-effective to replace. Don’t settle for cheap rotors that crack after a weekend—AP’s J Hook rings offer better durability and real long-term value. Fewer replacements mean more track time, less downtime, and peace of mind knowing you're running the best. Used by Champions. Trusted by Experts. From endurance racers to HPDE enthusiasts, AP Racing brake rotors are trusted worldwide for their reliability, longevity, and performance under pressure. Whether you're shaving seconds off your lap time or building a dedicated track car, the J Hook delivers a professional-grade solution that won’t let you down. AP Racing J Hook Brake Rotors for Auto Racing, Track Days & HPDE Why Rotor Design Matters: Heat Expansion and Floating Technology As with most metals, iron brake discs expand significantly under heat. When temperatures rise, the disc grows radially—expanding in both diameter and circumference. Traditional one-piece rotors struggle to accommodate this natural expansion. As the outer edge pulls away from the center under heat stress, it creates a condition called “coning”—a distortion that compromises pad-to-rotor contact. This distortion can lead to uneven pad wear, brake tapering, and an inconsistent, long brake pedal. AP Racing two-piece floating brake rotors are purpose-built to eliminate these issues. Engineered with “float” built into the disc or hat assembly, these rotors feature oblong-shaped mounting holes that allow the hardware to slide as the disc heats up. This flexibility ensures the disc runs true within the caliper under high-temperature loads, effectively reducing distortion, minimizing pad taper and stress cracks, and promoting longer component life. Custom Mounting Hardware & Anti-Knockback Spring Clips AP Racing rotors utilize application-specific, U.S.-made mounting hardware—not generic bolts. These premium components are the exact parts used in AP’s professional motorsport products, engineered to withstand the rigors of competitive racing. To manage lateral disc motion that can push caliper pistons backward (known as knockback), AP Racing integrates anti-knockback spring clips on alternating bobbins—five on a ten-bolt setup, six on a twelve-bolt disc. These clips keep the aluminum hat and iron disc ring properly aligned while still allowing for radial float. Bonus: they eliminate annoying rattles and vibrations, ensuring a quieter, more refined braking experience. High-Performance Hat Design for Heat Isolation The disc hats in AP Racing’s two-piece floating rotors are CNC-machined from 6061-T6 billet aluminum and finished with a hard anodized coating. This high-strength aluminum alloy was selected for its ability to maintain structural integrity even at elevated temperatures. AP adds scalloped channels beneath the hat to further encourage airflow and heat evacuation from the outer disc face, minimizing thermal transfer to hubs and wheel bearings—helping reduce maintenance costs on these expensive components. Internal Vane Engineering: Airflow Optimization & Thermal Stability AP Racing’s internal vane design sets them apart from OEM and most aftermarket competitors. While many factory brake discs use non-directional pillar vanes (low-cost and NVH-focused), AP Racing rotors use directional vanes engineered for maximum airflow. These rotors are side-specific—meaning you’ll receive a unique left and right disc in each set—ensuring optimized cooling through strategic vane orientation and shape. Beyond that, AP Racing rotors feature a superior vane count, typically ranging from 60 to 84 vanes, compared to 30–48 in most aftermarket rotors. After extensive CFD and thermal analysis, this high vane count was proven to: Increase airspeed and thermal transfer Reduce recirculation and deflection at the disc face Minimize coning, cracking, and brake fade Deliver more even pad contact and extended rotor life J Hook Slot Pattern: Exclusive to AP Racing Slots and drill holes may improve initial bite, but they also introduce “cool spots” in the rotor face—areas of uneven heating that can lead to stress risers, cracks, and pad vibration. OEM rotors often avoid this by leaving the disc face blank, but that compromises bite and brake feel. AP Racing’s patented J Hook design, developed through rigorous R&D, solves this problem. The hooks are meticulously spaced around the disc’s circumference and from hat to edge, forming a continuous distortion path that ensures even heat distribution. This encourages uniform pad deposits during bed-in, helps reduce judder and cracking, and improves consistency under repeated high-load braking. In addition, the J Hook slots provide more leading edges for pads to grip than traditional curved slots or blank rotors. While this might generate a mild whirring sound during braking, the benefits—more bite, cleaner bedding, better pedal feel—make it the top choice for committed racers and serious track day drivers. Metallurgy Backed by 50+ Years of Motorsport Leadership AP Racing's reputation is built on performance, and their proprietary iron alloy used in J Hook rotors is no exception. Drawing from over five decades of elite motorsport experience, including 750+ Formula 1 wins and widespread use across NASCAR, AP’s engineers have developed a disc alloy that excels under sustained racing temperatures and stress. Where OEM discs focus on affordability and mass production, AP Racing’s J Hook rotors are purpose-built for motorsport durability and heat resistance. Affordable Replacement Cost: Serious Value for Serious Drivers Even the best brake rotors are consumables. When you drive hard—especially at the track—your discs will eventually wear out. That’s why AP Racing designed their replacement iron rings to be cost-effective, allowing you to replace worn parts without breaking the bank. Compare that to constantly buying cheap $150 rotors every weekend—rotors that can't handle the heat and need to be swapped frequently. With AP Racing’s J Hook rotors, you get longer service intervals, less downtime, and better performance over time, making them an incredibly smart long-term investment. Proven on Track. Trusted by Champions. Top-tier racing teams rely on AP Racing J Hook rotors for one reason: they perform under pressure. Whether you're running time trials, attending HPDE events, or competing in wheel-to-wheel racing, these rotors offer professional-grade reliability, safety, and performance. Bedding and Preparation of AP Racing J Hook Discs Properly preparing your new brake discs before heavy use is extremely important. The goal of bedding-in your brake pads and discs is to mate them together properly and prepare them for heavy use.  When prepared properly, or bed-in, your pads will transfer a thin layer of material to the disc face (transfer layer).  The pads in your caliper will then actually ride on that thin layer of pad material you’ve put down on the rotor, rather than rubbing directly on the iron rotor face.  A good transfer layer is going to give you superior brake pedal feel, less noise, superior pad wear, and lower the chances of cracking your discs. Important Notes- PLEASE READ! First, make sure you are on a closed course to perform a proper bed-in.  Do NOT perform the procedure on public roads.  You need a stretch of asphalt with long straights, good visibility, and no potential obstructions.  Make sure you are in a position to safely and repeatedly attain the necessary speeds to perform the bed-in procedure.  A controlled racetrack is the best place to perform this procedure.  AP Racing and Competition Motorsport in no way suggest or condone speeding on public roads or breaking the law in your car, nor do we take responsibility for any damage or injury that occurs as a result of using our product or these procedures.  You are performing the bed-in procedure at your own risk.  During these procedures, it’s critical that you never come to a complete stop with your foot on the brake pedal.  If you have brake ducts on your car, you may want to block them off to allow your brake system to heat up easily. The procedure outlined below is a generic procedure for most types of mild race pad.  Please check your pad manufacturer’s recommended bed-in procedure. Accelerate to approximately 60mph and then decelerate down to 5 mph.  If your car has ABS, you should try to hold the brakes at a point just before ABS intervention.  Once the car slows to 5mph, immediately accelerate back up to about 60mph, and brake again to roughly 5mph.  Repeat this series of stopping and accelerating 8 to 10 times.  Again, do not come to a complete stop with your foot on the brake pedal. Cool the brake system down by cruising at 45mph+ for 5 to 10 minutes. Visually inspect your discs.  They should be a blue/grey color (instead of shiny silver), and have an even layer of pad material across and around the entire rotor face. If the AP Racing rotors don’t have a layer of pad material on them, perform another series of stops in the manner outlined above.

AP Racing J Hook 380x30mm Replacement Rear Brake Rotor Rings This kit is two replacement rotor discs and new installation hardware only. Center hats are not included. Replacement rotor rings for AP Racing 13.01.20018. Fits The Following Cars (w/ OEM iron rotors): Porsche 992 GT3 (Rear) Porsche 992 GT3RS (Rear) Porsche 718/982 GT4RS (Rear) Porsche 991 GT2RS/GT3/GT3RS (Rear) Porsche 981 GT4 (Rear) Sold/priced per pair of rotor rings (including hardware). AP Racing J Hook Brake Rotors – The Gold Standard in Track Day & Racing Performance Engineered for professional motorsport, HPDE, and dedicated track day use, AP Racing’s J Hook Brake Rotors deliver uncompromising performance, thermal stability, and consistent braking power. These two-piece, floating rotors are built to handle the extreme demands of road racing, with design features derived from over 50 years of elite competition—including Formula 1, NASCAR, and IMSA. Unlike conventional one-piece rotors, AP Racing’s two-piece floating design features a billet aluminum hat mated to a cast iron disc via precision-engineered bobbins. This setup allows for controlled radial expansion under high heat, minimizing distortion and coning. The result? More even pad wear, a firmer pedal feel, and longer component life, even during extended lapping sessions or endurance racing. Floating hardware includes anti-knockback spring clips that reduce piston retraction while eliminating common NVH issues like rattling. Why Choose AP Racing J Hook Rotors? Advanced Cooling, Superior Bite, Unmatched Durability At the heart of every rotor is AP Racing’s proprietary high-carbon iron alloy, developed to withstand repeated thermal cycling without cracking or warping. Internally, directional vanes—far superior to OEM pillar or straight vane designs—maximize airflow and cooling. With 60 to 84 vanes per rotor, AP Racing achieves faster heat evacuation, reduced brake fade, and a more consistent friction surface. These rotors are left/right-specific for optimal airflow and balance. The exclusive J Hook slot pattern offers enhanced initial bite and promotes uniform heat distribution across the rotor face, reducing pad deposits and vibration. Unlike drilled rotors or straight-slot competitors, the J Hook design provides cleaner pad transfer during bed-in and superior modulation under braking—ideal for serious drivers who demand feedback and control. Yes, you might hear a little more whirr, but you’ll gain the stopping power, consistency, and longevity your lap times demand. Premium Components, Affordable Performance The rotor hats are CNC-machined from 6061-T6 billet aluminum and hard anodized for strength and heat resistance. Scalloped edges under the hat further assist heat dissipation. All hardware is U.S.-made to AP Racing spec, the same quality found on pro-level racing platforms. And while these rotors are race-proven, they’re also surprisingly cost-effective to replace. Don’t settle for cheap rotors that crack after a weekend—AP’s J Hook rings offer better durability and real long-term value. Fewer replacements mean more track time, less downtime, and peace of mind knowing you're running the best. Used by Champions. Trusted by Experts. From endurance racers to HPDE enthusiasts, AP Racing brake rotors are trusted worldwide for their reliability, longevity, and performance under pressure. Whether you're shaving seconds off your lap time or building a dedicated track car, the J Hook delivers a professional-grade solution that won’t let you down. AP Racing J Hook Brake Rotors for Auto Racing, Track Days & HPDE Why Rotor Design Matters: Heat Expansion and Floating Technology As with most metals, iron brake discs expand significantly under heat. When temperatures rise, the disc grows radially—expanding in both diameter and circumference. Traditional one-piece rotors struggle to accommodate this natural expansion. As the outer edge pulls away from the center under heat stress, it creates a condition called “coning”—a distortion that compromises pad-to-rotor contact. This distortion can lead to uneven pad wear, brake tapering, and an inconsistent, long brake pedal. AP Racing two-piece floating brake rotors are purpose-built to eliminate these issues. Engineered with “float” built into the disc or hat assembly, these rotors feature oblong-shaped mounting holes that allow the hardware to slide as the disc heats up. This flexibility ensures the disc runs true within the caliper under high-temperature loads, effectively reducing distortion, minimizing pad taper and stress cracks, and promoting longer component life. Custom Mounting Hardware & Anti-Knockback Spring Clips AP Racing rotors utilize application-specific, U.S.-made mounting hardware—not generic bolts. These premium components are the exact parts used in AP’s professional motorsport products, engineered to withstand the rigors of competitive racing. To manage lateral disc motion that can push caliper pistons backward (known as knockback), AP Racing integrates anti-knockback spring clips on alternating bobbins—five on a ten-bolt setup, six on a twelve-bolt disc. These clips keep the aluminum hat and iron disc ring properly aligned while still allowing for radial float. Bonus: they eliminate annoying rattles and vibrations, ensuring a quieter, more refined braking experience. High-Performance Hat Design for Heat Isolation The disc hats in AP Racing’s two-piece floating rotors are CNC-machined from 6061-T6 billet aluminum and finished with a hard anodized coating. This high-strength aluminum alloy was selected for its ability to maintain structural integrity even at elevated temperatures. AP adds scalloped channels beneath the hat to further encourage airflow and heat evacuation from the outer disc face, minimizing thermal transfer to hubs and wheel bearings—helping reduce maintenance costs on these expensive components. Internal Vane Engineering: Airflow Optimization & Thermal Stability AP Racing’s internal vane design sets them apart from OEM and most aftermarket competitors. While many factory brake discs use non-directional pillar vanes (low-cost and NVH-focused), AP Racing rotors use directional vanes engineered for maximum airflow. These rotors are side-specific—meaning you’ll receive a unique left and right disc in each set—ensuring optimized cooling through strategic vane orientation and shape. Beyond that, AP Racing rotors feature a superior vane count, typically ranging from 60 to 84 vanes, compared to 30–48 in most aftermarket rotors. After extensive CFD and thermal analysis, this high vane count was proven to: Increase airspeed and thermal transfer Reduce recirculation and deflection at the disc face Minimize coning, cracking, and brake fade Deliver more even pad contact and extended rotor life J Hook Slot Pattern: Exclusive to AP Racing Slots and drill holes may improve initial bite, but they also introduce “cool spots” in the rotor face—areas of uneven heating that can lead to stress risers, cracks, and pad vibration. OEM rotors often avoid this by leaving the disc face blank, but that compromises bite and brake feel. AP Racing’s patented J Hook design, developed through rigorous R&D, solves this problem. The hooks are meticulously spaced around the disc’s circumference and from hat to edge, forming a continuous distortion path that ensures even heat distribution. This encourages uniform pad deposits during bed-in, helps reduce judder and cracking, and improves consistency under repeated high-load braking. In addition, the J Hook slots provide more leading edges for pads to grip than traditional curved slots or blank rotors. While this might generate a mild whirring sound during braking, the benefits—more bite, cleaner bedding, better pedal feel—make it the top choice for committed racers and serious track day drivers. Metallurgy Backed by 50+ Years of Motorsport Leadership AP Racing's reputation is built on performance, and their proprietary iron alloy used in J Hook rotors is no exception. Drawing from over five decades of elite motorsport experience, including 750+ Formula 1 wins and widespread use across NASCAR, AP’s engineers have developed a disc alloy that excels under sustained racing temperatures and stress. Where OEM discs focus on affordability and mass production, AP Racing’s J Hook rotors are purpose-built for motorsport durability and heat resistance. Affordable Replacement Cost: Serious Value for Serious Drivers Even the best brake rotors are consumables. When you drive hard—especially at the track—your discs will eventually wear out. That’s why AP Racing designed their replacement iron rings to be cost-effective, allowing you to replace worn parts without breaking the bank. Compare that to constantly buying cheap $150 rotors every weekend—rotors that can't handle the heat and need to be swapped frequently. With AP Racing’s J Hook rotors, you get longer service intervals, less downtime, and better performance over time, making them an incredibly smart long-term investment. Proven on Track. Trusted by Champions. Top-tier racing teams rely on AP Racing J Hook rotors for one reason: they perform under pressure. Whether you're running time trials, attending HPDE events, or competing in wheel-to-wheel racing, these rotors offer professional-grade reliability, safety, and performance. Bedding and Preparation of AP Racing J Hook Discs Properly preparing your new brake discs before heavy use is extremely important. The goal of bedding-in your brake pads and discs is to mate them together properly and prepare them for heavy use.  When prepared properly, or bed-in, your pads will transfer a thin layer of material to the disc face (transfer layer).  The pads in your caliper will then actually ride on that thin layer of pad material you’ve put down on the rotor, rather than rubbing directly on the iron rotor face.  A good transfer layer is going to give you superior brake pedal feel, less noise, superior pad wear, and lower the chances of cracking your discs. Important Notes- PLEASE READ! First, make sure you are on a closed course to perform a proper bed-in.  Do NOT perform the procedure on public roads.  You need a stretch of asphalt with long straights, good visibility, and no potential obstructions.  Make sure you are in a position to safely and repeatedly attain the necessary speeds to perform the bed-in procedure.  A controlled racetrack is the best place to perform this procedure.  AP Racing and Competition Motorsport in no way suggest or condone speeding on public roads or breaking the law in your car, nor do we take responsibility for any damage or injury that occurs as a result of using our product or these procedures.  You are performing the bed-in procedure at your own risk.  During these procedures, it’s critical that you never come to a complete stop with your foot on the brake pedal.  If you have brake ducts on your car, you may want to block them off to allow your brake system to heat up easily. The procedure outlined below is a generic procedure for most types of mild race pad.  Please check your pad manufacturer’s recommended bed-in procedure. Accelerate to approximately 60mph and then decelerate down to 5 mph.  If your car has ABS, you should try to hold the brakes at a point just before ABS intervention.  Once the car slows to 5mph, immediately accelerate back up to about 60mph, and brake again to roughly 5mph.  Repeat this series of stopping and accelerating 8 to 10 times.  Again, do not come to a complete stop with your foot on the brake pedal. Cool the brake system down by cruising at 45mph+ for 5 to 10 minutes. Visually inspect your discs.  They should be a blue/grey color (instead of shiny silver), and have an even layer of pad material across and around the entire rotor face. If the AP Racing rotors don’t have a layer of pad material on them, perform another series of stops in the manner outlined above.

AP Racing 380x30mm 2-piece J Hook Rear Brake Rotors for Porsche (OEM Iron) Fit The Following Cars (w/ OEM Iron Rotors) Porsche 992 GT3 (Rear) Porsche 992 GT3RS (Rear) Porsche 718/982 GT4RS (Rear) Porsche 991 GT2RS/GT3/GT3RS (Rear) Porsche 981 GT4 (Rear) Sold/priced per pair. AP Racing 2-piece Competition J Hook rear disc pair for 991.1 & 991.2 GT3 (including GT3RS), 992 GT3, and 718 GT4 and GT4 RS with iron discs 380x30mm (14.96" x 1.18") 72 Vane, D67 radial depth Huge increase in airflow, cooling capacity, and durability vs. OEM discs Saves 3-4 lbs. unsprung weight per side Retains full parking brake functionality Designed for: club racing, time trial, auto-x, HPDE Works with OEM calipers, no modifications required Ultralight, fully floating, anodized billet aluminum hat with float control/anti-rattle clips Sold/priced per pair. AP Racing J Hook Brake Rotors – The Gold Standard in Track Day & Racing Performance Engineered for professional motorsport, HPDE, and dedicated track day use, AP Racing’s J Hook Brake Rotors deliver uncompromising performance, thermal stability, and consistent braking power. These two-piece, floating rotors are built to handle the extreme demands of road racing, with design features derived from over 50 years of elite competition—including Formula 1, NASCAR, and IMSA. Unlike conventional one-piece rotors, AP Racing’s two-piece floating design features a billet aluminum hat mated to a cast iron disc via precision-engineered bobbins. This setup allows for controlled radial expansion under high heat, minimizing distortion and coning. The result? More even pad wear, a firmer pedal feel, and longer component life, even during extended lapping sessions or endurance racing. Floating hardware includes anti-knockback spring clips that reduce piston retraction while eliminating common NVH issues like rattling. Why Choose AP Racing J Hook Rotors? Advanced Cooling, Superior Bite, Unmatched Durability At the heart of every rotor is AP Racing’s proprietary high-carbon iron alloy, developed to withstand repeated thermal cycling without cracking or warping. Internally, directional vanes—far superior to OEM pillar or straight vane designs—maximize airflow and cooling. With 60 to 84 vanes per rotor, AP Racing achieves faster heat evacuation, reduced brake fade, and a more consistent friction surface. These rotors are left/right-specific for optimal airflow and balance. The exclusive J Hook slot pattern offers enhanced initial bite and promotes uniform heat distribution across the rotor face, reducing pad deposits and vibration. Unlike drilled rotors or straight-slot competitors, the J Hook design provides cleaner pad transfer during bed-in and superior modulation under braking—ideal for serious drivers who demand feedback and control. Yes, you might hear a little more whirr, but you’ll gain the stopping power, consistency, and longevity your lap times demand. Premium Components, Affordable Performance The rotor hats are CNC-machined from 6061-T6 billet aluminum and hard anodized for strength and heat resistance. Scalloped edges under the hat further assist heat dissipation. All hardware is U.S.-made to AP Racing spec, the same quality found on pro-level racing platforms. And while these rotors are race-proven, they’re also surprisingly cost-effective to replace. Don’t settle for cheap rotors that crack after a weekend—AP’s J Hook rings offer better durability and real long-term value. Fewer replacements mean more track time, less downtime, and peace of mind knowing you're running the best. Used by Champions. Trusted by Experts. From endurance racers to HPDE enthusiasts, AP Racing brake rotors are trusted worldwide for their reliability, longevity, and performance under pressure. Whether you're shaving seconds off your lap time or building a dedicated track car, the J Hook delivers a professional-grade solution that won’t let you down.   AP Racing J Hook Brake Rotors for Auto Racing, Track Days & HPDE Why Rotor Design Matters: Heat Expansion and Floating Technology As with most metals, iron brake discs expand significantly under heat. When temperatures rise, the disc grows radially—expanding in both diameter and circumference. Traditional one-piece rotors struggle to accommodate this natural expansion. As the outer edge pulls away from the center under heat stress, it creates a condition called “coning”—a distortion that compromises pad-to-rotor contact. This distortion can lead to uneven pad wear, brake tapering, and an inconsistent, long brake pedal. AP Racing two-piece floating brake rotors are purpose-built to eliminate these issues. Engineered with “float” built into the disc or hat assembly, these rotors feature oblong-shaped mounting holes that allow the hardware to slide as the disc heats up. This flexibility ensures the disc runs true within the caliper under high-temperature loads, effectively reducing distortion, minimizing pad taper and stress cracks, and promoting longer component life. Custom Mounting Hardware & Anti-Knockback Spring Clips AP Racing rotors utilize application-specific, U.S.-made mounting hardware—not generic bolts. These premium components are the exact parts used in AP’s professional motorsport products, engineered to withstand the rigors of competitive racing. To manage lateral disc motion that can push caliper pistons backward (known as knockback), AP Racing integrates anti-knockback spring clips on alternating bobbins—five on a ten-bolt setup, six on a twelve-bolt disc. These clips keep the aluminum hat and iron disc ring properly aligned while still allowing for radial float. Bonus: they eliminate annoying rattles and vibrations, ensuring a quieter, more refined braking experience. High-Performance Hat Design for Heat Isolation The disc hats in AP Racing’s two-piece floating rotors are CNC-machined from 6061-T6 billet aluminum and finished with a hard anodized coating. This high-strength aluminum alloy was selected for its ability to maintain structural integrity even at elevated temperatures. AP adds scalloped channels beneath the hat to further encourage airflow and heat evacuation from the outer disc face, minimizing thermal transfer to hubs and wheel bearings—helping reduce maintenance costs on these expensive components. Internal Vane Engineering: Airflow Optimization & Thermal Stability AP Racing’s internal vane design sets them apart from OEM and most aftermarket competitors. While many factory brake discs use non-directional pillar vanes (low-cost and NVH-focused), AP Racing rotors use directional vanes engineered for maximum airflow. These rotors are side-specific—meaning you’ll receive a unique left and right disc in each set—ensuring optimized cooling through strategic vane orientation and shape. Beyond that, AP Racing rotors feature a superior vane count, typically ranging from 60 to 84 vanes, compared to 30–48 in most aftermarket rotors. After extensive CFD and thermal analysis, this high vane count was proven to: Increase airspeed and thermal transfer Reduce recirculation and deflection at the disc face Minimize coning, cracking, and brake fade Deliver more even pad contact and extended rotor life J Hook Slot Pattern: Exclusive to AP Racing Slots and drill holes may improve initial bite, but they also introduce “cool spots” in the rotor face—areas of uneven heating that can lead to stress risers, cracks, and pad vibration. OEM rotors often avoid this by leaving the disc face blank, but that compromises bite and brake feel. AP Racing’s patented J Hook design, developed through rigorous R&D, solves this problem. The hooks are meticulously spaced around the disc’s circumference and from hat to edge, forming a continuous distortion path that ensures even heat distribution. This encourages uniform pad deposits during bed-in, helps reduce judder and cracking, and improves consistency under repeated high-load braking. In addition, the J Hook slots provide more leading edges for pads to grip than traditional curved slots or blank rotors. While this might generate a mild whirring sound during braking, the benefits—more bite, cleaner bedding, better pedal feel—make it the top choice for committed racers and serious track day drivers. Metallurgy Backed by 50+ Years of Motorsport Leadership AP Racing's reputation is built on performance, and their proprietary iron alloy used in J Hook rotors is no exception. Drawing from over five decades of elite motorsport experience, including 750+ Formula 1 wins and widespread use across NASCAR, AP’s engineers have developed a disc alloy that excels under sustained racing temperatures and stress. Where OEM discs focus on affordability and mass production, AP Racing’s J Hook rotors are purpose-built for motorsport durability and heat resistance. Affordable Replacement Cost: Serious Value for Serious Drivers Even the best brake rotors are consumables. When you drive hard—especially at the track—your discs will eventually wear out. That’s why AP Racing designed their replacement iron rings to be cost-effective, allowing you to replace worn parts without breaking the bank. Compare that to constantly buying cheap $150 rotors every weekend—rotors that can't handle the heat and need to be swapped frequently. With AP Racing’s J Hook rotors, you get longer service intervals, less downtime, and better performance over time, making them an incredibly smart long-term investment. Proven on Track. Trusted by Champions. Top-tier racing teams rely on AP Racing J Hook rotors for one reason: they perform under pressure. Whether you're running time trials, attending HPDE events, or competing in wheel-to-wheel racing, these rotors offer professional-grade reliability, safety, and performance. Bedding and preparation of AP Racing J Hook Disc Properly preparing your new brake discs before heavy use is extremely important. The goal of bedding-in your brake pads and discs is to mate them together properly and prepare them for heavy use.  When prepared properly, or bed-in, your pads will transfer a thin layer of material to the disc face (transfer layer).  The pads in your caliper will then actually ride on that thin layer of pad material you’ve put down on the rotor, rather than rubbing directly on the iron rotor face.  A good transfer layer is going to give you superior brake pedal feel, less noise, superior pad wear, and lower the chances of cracking your discs. Important Notes- PLEASE READ! First, make sure you are on a closed course to perform a proper bed-in.  Do NOT perform the procedure on public roads.  You need a stretch of asphalt with long straights, good visibility, and no potential obstructions.  Make sure you are in a position to safely and repeatedly attain the necessary speeds to perform the bed-in procedure.  A controlled racetrack is the best place to perform this procedure.  AP Racing and Competition Motorsport in no way suggest or condone speeding on public roads or breaking the law in your car, nor do we take responsibility for any damage or injury that occurs as a result of using our product or these procedures.  You are performing the bed-in procedure at your own risk.  During these procedures, it’s critical that you never come to a complete stop with your foot on the brake pedal.  If you have brake ducts on your car, you may want to block them off to allow your brake system to heat up easily. The procedure outlined below is a generic procedure for most types of mild race pad.  Please check your pad manufacturer’s recommended bed-in procedure. Accelerate to approximately 60mph and then decelerate down to 5 mph.  If your car has ABS, you should try to hold the brakes at a point just before ABS intervention.  Once the car slows to 5mph, immediately accelerate back up to about 60mph, and brake again to roughly 5mph.  Repeat this series of stopping and accelerating 8 to 10 times.  Again, do not come to a complete stop with your foot on the brake pedal. Cool the brake system down by cruising at 45mph+ for 5 to 10 minutes. Visually inspect your discs.  They should be a blue/grey color (instead of shiny silver), and have an even layer of pad material across and around the entire rotor face. If the AP Racing rotors don’t have a layer of pad material on them, perform another series of stops in the manner outlined above.

Performance Friction PFC 380.34.0062.451/461 380mm Front Floating Racing Brake Rotor Replacements Fit The Following Cars (w/ OEM Iron Rotors) - Center hat Excluded, rotor disc only. Replacement Disc Only For PFC 380.070.63/64 Porsche 991 GT3 (Front) Porsche 991 GT3RS (Front) Porsche 981 GT4 (Front) PFC the manufacturer of Porsche Cup braking systems developed a 380x34mm front rotor replacement kit that is a direct replacement for the OEM Iron Brake rotors.  Performance Friction PFC V3 Discs with Zero Failure Technology Unique Rotor and Hat interface, eliminating most hardware. The elimination of hardware reduces weight, complexity, and installation time for less down time and more seat time on the track.  Replace your rotor discs in minutes with a flat head screwdriver PFC metallurgy specified for high Thermal stability and mechanical strength for increased longevity 48 vane geometry engineered for increased airflow for increased brake cooling during the heat of the battle while on track Patented slot pattern for increased initial bit and pad surface conditioning Lightweight forged hard anodized aluminum hat for increased durability and performance The two-piece PFC V3 design allows for disc-only replacement as well, minimizing future replacement costs and delivering outstanding performance. Sold/priced per pair.

Performance Friction PFC 410.069.63-64 410mm Two-Piece Front Floating Racing Brake Rotors Fit The Following Cars (w/ OEM Iron Rotors or PCCB Rotors) Porsche 991 GT2RS PCCB (Front) Porsche 991 GT3 PCCB (Front) Porsche 991 GT3RS PCCB (Front) Porsche 718 / 982 GT4RS PCCB or Iron (Front) Porsche 718 GT4 PCCB (Front) PFC the manufacturer of Porsche Cup braking systems developed a 410mm front rotor replacement kit that is a direct replacement for the OEM 991 GT or 718 GT4 PCCB Brake rotors or OEM 718 / 982 GT4RS with PCCB or Iron rotors.  Performance Friction PFC V3 Disks with Zero Failure Technology Unique Rotor and Hat interface, eliminating most hardware. The elimination of hardware reduces weight, complexity, and installation time for less down time and more seat time on the track.  Replace your rotor discs in minutes with a flat head screwdriver PFC metallurgy specified for high Thermal stability and mechanical strength for increased longevity 48 vane geometry engineered for increased airflow for increased brake cooling during the heat of the battle while on track Patented slot pattern for increased initial bit and pad surface conditioning Lightweight forged hard anodized aluminum hat for increased durability and performance The two-piece PFC V3 design allows for disc-only replacement as well, minimizing future replacement costs and delivering outstanding performance. Sold/priced per pair.

Performance Friction PFC 390.075.63-64 390mm Two-Piece Rear Floating Racing Brake Rotors Fit The Following Cars (w/ OEM PCCB Rotors) Porsche 992 GT3 (Rear) Porsche 992 GT3RS (Rear) Porsche 718/982 GT4RS (Rear) Porsche 991 GT2RS/GT3/GT3RS (Rear) Porsche 981 GT4 (Rear) PFC the manufacturer of Porsche Cup braking systems developed a 390x32 mm rear rotor replacement kit that is a direct replacement for the OEM Steel Brake rotors.  Performance Friction PFC V3 Disks with Zero Failure Technology Unique Rotor and Hat interface, eliminating most hardware. The elimination of hardware reduces weight, complexity, and installation time for less down time and more seat time on the track.  Replace your rotor discs in minutes with a flat head screwdriver PFC metallurgy specified for high Thermal stability and mechanical strength for increased longevity 48 vane geometry engineered for increased airflow for increased brake cooling during the heat of the battle while on track Patented slot pattern for increased initial bit and pad surface conditioning Lightweight forged hard anodized aluminum hat for increased durability and performance The two-piece PFC V3 design allows for disc-only replacement as well, minimizing future replacement costs and delivering outstanding performance. PFC’s V3 discs are optimized to ensure the highest level of performance, wear and durability for your Porsche’s braking system.  These high-performance OEM replacement assemblies now feature aluminium hats in both front and rear, similar to the original. There is a saving of over one pound by trimming excess material from the unused areas around the disc in our new V3 ZeroFailures™ design, which will allow for disc changes in a matter of seconds with a flat head screwdriver. Sold/priced per pair.

Performance Friction PFC 380.075.63-64 380mm Two-Piece Rear Floating Racing Brake Rotors Fit The Following Cars (w/ OEM Iron Rotors) Porsche 992 GT3 (Rear) Porsche 992 GT3RS (Rear) Porsche 718/982 GT4RS (Rear) Porsche 991 GT2RS/GT3/GT3RS (Rear) Porsche 981 GT4 (Rear) PFC the manufacturer of Porsche Cup braking systems developed a 380x30 mm rear rotor replacement kit that is a direct replacement for the OEM Steel Brake rotors.  Performance Friction PFC V3 Disks with Zero Failure Technology Unique Rotor and Hat interface, eliminating most hardware. The elimination of hardware reduces weight, complexity, and installation time for less down time and more seat time on the track.  Replace your rotor discs in minutes with a flat head screwdriver PFC metallurgy specified for high Thermal stability and mechanical strength for increased longevity 48 vane geometry engineered for increased airflow for increased brake cooling during the heat of the battle while on track Patented slot pattern for increased initial bit and pad surface conditioning Lightweight forged hard anodized aluminum hat for increased durability and performance The two-piece PFC V3 design allows for disc-only replacement as well, minimizing future replacement costs and delivering outstanding performance. PFC’s V3 discs are optimized to ensure the highest level of performance, wear and durability for your Porsche’s braking system.  These high-performance OEM replacement assemblies now feature aluminium hats in both front and rear, similar to the original. There is a saving of over one pound by trimming excess material from the unused areas around the disc in our new V3 ZeroFailures™ design, which will allow for disc changes in a matter of seconds with a flat head screwdriver. Sold/priced per pair.

Porsche 991 GT3 Cup Front Rotors (380x32) The Girodisc system is a direct replacement for the OE front rotors on the Porsche 991 GT3 Cup car. No modifications are required—these lightweight 2-piece floating rotors bolt directly to the car and work seamlessly with factory calipers. Designed for the demands of professional motorsport, Girodisc rotors deliver superior cooling, durability, and braking precision under the harshest track conditions. Built for Competition-Level Performance Girodisc 380x32mm rotors are engineered and machined entirely in the USA from the highest-quality materials. The aluminum hat is CNC-machined from 6061-T6 aircraft-grade alloy for weight savings and strength. The iron rotor rings are made from Girodisc’s proprietary high-carbon alloy, poured and machined in-house for exacting balance and heat resistance. The curved vane design acts as a centrifugal pump, drawing air through the disc to reduce fade and maintain consistent braking throughout long races. A1-238 Girodisc 380mm 2pc Front Brake Rotor Vehicle Fitment Porsche 911 GT3 Cup (991.1 & 991.2) Porsche 911 GT3 R (for equivalent front setup) A1-238 Girodisc 380mm 2pc Front Brake Rotor Features Direct OEM Replacement: Bolts directly to factory hubs and calipers—no modifications needed. 380x32mm Rotor Size: Provides greater surface area and heat capacity for endurance-level braking. Lightweight Two-Piece Design: Reduces unsprung and rotational mass to improve cornering response and acceleration. Curved Vane Internal Cooling: Directional vanes act as centrifugal pumps, pulling cool air through the disc to reduce temperatures and extend pad life. Floating Mount System: Twelve high-strength alloy drive pins with anti-noise spring washers allow the rotor to expand under heat while preventing rattle. Replaceable Rings: The aluminum hats are reusable—only replace the iron rings when worn. Made in the USA: Designed, cast, machined, and assembled domestically to the highest racing standards. A1-238 Girodisc 380mm 2pc Front Brake Rotor FAQs Do these rotors fit OEM calipers? Yes, they fit directly with the factory Porsche Motorsport calipers. Can they handle endurance racing? Absolutely. Girodisc rotors are built to survive repeated high-temperature cycles during endurance and sprint events. What makes Girodisc better than OEM? They offer reduced weight, better cooling, and replaceable rotor rings, saving long-term maintenance costs. Are they sold as a pair? Yes, Girodisc rotors are sold and priced per pair. Enhance your Porsche 991 GT3 Cup’s braking performance with Girodisc’s 380x32mm 2-piece floating rotors. Designed for uncompromising race performance, these rotors deliver cooler operation, consistent pedal feel, and lasting durability for the most demanding track conditions.

Girodisc  Rear Brake Rotors – Porsche 991 GT3 Cup Car The Girodisc A2-238 Rear Rotor Set (380x30mm) is a direct replacement for the OE cup car discs used on the Porsche 991 GT3 Cup. Engineered for performance and reliability under extreme track conditions, these rotors bolt directly to your car and work seamlessly with the original calipers and ABS system—no modifications required. Race-Proven Two-Piece Design Each Girodisc rotor is designed and manufactured in the USA with precision components to ensure durability and superior thermal management. The central hat section is CNC-machined from U.S.-sourced 6061-T6 aircraft-grade aluminum, while the outer ring is made from Girodisc’s proprietary cast iron alloy, poured and machined entirely in-house. The curved vane design actively pumps cooling air through the disc, reducing temperatures during intense braking to prevent fade and warping. A2-238 Girodisc 380mm 2pc Rear Brake Rotor Features • Direct replacement for OEM Porsche 991 GT3 Cup rear discs (380x30mm)• Two-piece floating rotor design for optimal heat management• 6061-T6 aluminum hats machined from U.S.-sourced billet• Proprietary cast iron rotor rings with curved vane cooling geometry• 12 high-strength alloy steel drive pins with cadmium plating• Anti-noise spring washers eliminate rattle while maintaining full float• Class 12.9 hardware and hardened washers for secure mounting• Significantly reduces unsprung and rotational mass• Reusable hats—replace only rings when worn• Sold/priced per pair• Optional center-lock drive pin kit available A2-238 Girodisc 380mm 2pc Rear Brake Rotor Vehicle Fitment • Porsche 991 GT3 Cup (All model years) – Rear• Fits OEM calipers and ABS• Center-lock wheel option available upon request A2-238 Girodisc 380mm 2pc Rear Brake Rotor FAQs Do these rotors fit directly without modifications? Yes. The Girodisc A2-238 system is a direct bolt-on replacement for OEM rear discs on the 991 GT3 Cup. What is the advantage of a two-piece floating rotor? The floating design allows the iron rotor ring to expand under heat without stressing the aluminum hat, improving performance, reducing weight, and preventing cracking or distortion. Can I reuse the aluminum hats? Yes. Once the cast iron rings wear out, you can replace just the rings and retain the existing hats and hardware. Do these rotors make noise? No. The use of anti-noise spring washers ensures quiet operation even when cold, while maintaining true floating capability under heat. Are these rotors sold individually? No. The Girodisc A2-238 rotors are sold as a pair for the rear axle. Is a center-lock version available? Yes. Girodisc offers a specific drive pin option for vehicles equipped with OEM center-lock hubs—select this option when ordering. Enhance your Porsche 991 GT3 Cup’s braking performance with the Girodisc A2-238 2-Piece Rear Brake Rotors (380x30mm)—precision-engineered, race-proven, and built to handle the most demanding conditions on track.

Porsche 981 Front Rotors, incl. spacers & bolts Enhance the braking performance of your Porsche 981 with Girodisc’s precision-engineered two-piece floating front rotors. These rotors are a direct replacement for the OEM discs and come complete with spacers and bolts for a seamless installation. By increasing rotor size and reducing weight, Girodisc provides improved cooling, reduced fade, and faster braking response without altering your car’s factory bias or ABS functionality. Precision Engineering Meets Porsche Performance Machined in the USA from proprietary high-carbon cast iron and paired with 6061-T6 aluminum hats, Girodisc rotors deliver superior strength and temperature control. The curved vane internal design acts like a centrifugal pump, forcing cooling air through the rotor under load. The floating mount system allows for natural expansion under heat, reducing warping and maintaining smooth, consistent braking performance on both street and track. Vehicle Fitment • 2013–2016 Porsche Boxster (981)• 2013–2016 Porsche Cayman (981)• 2015–2016 Porsche Cayman GTS• 2014–2016 Porsche Boxster GTS• 2016 Porsche Boxster Spyder• 2016 Porsche Cayman GT4 Girodisc A1-035 Features • Direct bolt-on replacement with included spacers and bolts• Two-piece floating design reduces unsprung and rotational weight• 6061-T6 aircraft-grade aluminum hats, U.S.-made• Proprietary cast iron rings with curved internal vanes• Floating drive pin system with anti-noise spring washers• Enhanced thermal stability and fade resistance• Sold/priced per pair Porsche 981 Front Rotor FAQs: Does this kit include hardware? Yes, it includes all necessary spacers and bolts for installation. Do these rotors fit GT4 models? Yes, they are compatible with all 981 variants, including the Cayman GT4 and Boxster Spyder. Will these improve braking performance? Absolutely—expect improved pedal feel, reduced fade, and faster braking recovery. Are replacement rings available? Yes, Girodisc offers replacement rings to reuse your original aluminum hats for future servicing. Upgrade your Porsche 981 braking system with Girodisc front rotors—precision-built for drivers who demand performance, reliability, and balance on every lap.