A2-321 GiroDisc Rear Brake Rotors for Audi C8 S6/S7 (C8) 2019–2025

Upgrade your Audi's rear braking system with GiroDisc A2-321 Two-Piece Floating Rear Brake Rotors. Engineered as direct replacements for the factory rear iron brake rotors on the Audi C8 S6, C8 S7, and D5 S8, these precision-manufactured brake assemblies combine lightweight aluminum hats, proprietary high-carbon iron friction rings, and advanced cooling technology for demanding performance driving.
Featuring a 350mm diameter, 28mm thickness, and fully floating two-piece construction, the GiroDisc A2-321 rear rotors are designed to reduce unsprung weight and rotating mass while delivering consistent braking performance. Their serviceable construction allows worn friction rings to be replaced independently of the reusable aluminum hats.
High-Performance 350mm Rear Brake Rotors for Audi C8 S6, S7 & D5 S8
The GiroDisc A2-321 Rear Brake Rotor Assemblies offer a performance-focused upgrade for Audi S6, S7, and S8 models equipped with factory iron rear brakes.
Unlike conventional one-piece cast iron rotors, GiroDisc's advanced two-piece design combines a high-carbon iron friction ring with a lightweight 6061-T6 aluminum mounting hat. This construction helps reduce unnecessary rotating mass while allowing the rotor components to accommodate differences in thermal expansion during aggressive braking.
Each rotor features 48 internal curved cooling vanes designed to act as a centrifugal pump, drawing air through the rotor to help dissipate braking heat.
GiroDisc's fully floating mounting system utilizes high-strength steel drive pins, spring clips, and spring washers to provide controlled movement between the rotor ring and hat while maintaining street-friendly operation.
GiroDisc A2-321 Rear Brake Rotor Features
-
Direct Factory Replacement: Engineered for Audi C8 S6, C8 S7, and D5 S8 models equipped with factory iron rear brakes.
-
350mm Rotor Diameter: Vehicle-specific rear rotor dimensions for the intended factory braking system.
-
Two-Piece Floating Construction: Combines proprietary high-carbon iron friction rings with lightweight aluminum mounting hats.
-
Reduced Unsprung Weight: Lightweight construction helps reduce rotating mass at the rear axle.
-
Proprietary High-Carbon Iron: Specially formulated cast iron designed to withstand demanding braking conditions.
-
48 Curved Cooling Vanes: Advanced internal ventilation promotes airflow through the rotor for improved heat dissipation.
-
6061-T6 Aluminum Hats: Precision-machined aluminum mounting hats with a durable black anodized finish.
-
Fully Floating Hardware: High-strength steel drive pins accommodate thermal expansion between rotor components.
-
Corrosion-Resistant Drive Pins: Cadmium-plated steel hardware provides additional corrosion protection.
-
Street-Friendly Design: Spring clips and spring washers help control hardware movement and minimize unwanted rattling.
-
Replaceable Friction Rings: Reusable aluminum hats allow worn rotor rings to be replaced independently.
-
Made in the USA: Major rotor components are manufactured in-house by GiroDisc in Bellingham, Washington.
Technical Specifications
-
Manufacturer: GiroDisc
-
Part Number: A2-321
-
Product Type: Two-Piece Floating Rear Brake Rotors
-
Vehicle Application: Audi C8 S6 / C8 S7 / D5 S8
-
Brake Position: Rear
-
Required Brake Configuration: Factory Iron Brakes
-
Rotor Outside Diameter: 350mm
-
Rotor Thickness: 28mm
-
Minimum Rotor Thickness: 26mm
-
Rotor Weight: 18.4 lbs per rotor assembly
-
Cooling Vane Count: 48 Curved Vanes
-
Rotor Ring Material: Proprietary High-Carbon Iron
-
Rotor Hat Material: 6061-T6 Aluminum
-
Rotor Hat Finish: Black Anodized
-
Drive Pin Material: High-Strength Steel Alloy
-
Drive Pin Finish: Cadmium Plated
-
Rotor Construction: Two-Piece Fully Floating
-
Mounting Hardware: Steel Drive Pins, Spring Clips, and Spring Washers
-
Replacement Rotor Rings: GiroDisc D2-321
-
Manufacturing Location: Bellingham, Washington, USA
Vehicle Fitment
The GiroDisc A2-321 Rear Brake Rotors are designed for the following Audi applications equipped with factory iron rear brakes:
-
Audi S6 (C8): Factory iron rear brake system.
-
Audi S7 (C8): Factory iron rear brake system.
-
Audi S8 (D5): Factory iron rear brake system.
Important Fitment Note: These rotors are designed specifically for vehicles equipped with factory iron brakes. They are not listed as a direct replacement for factory carbon-ceramic brake systems.
Confirm your Audi's model generation, factory brake package, and original rotor dimensions before ordering. Compatibility with other Audi models or aftermarket brake conversions should not be assumed.
Advanced High-Carbon Iron Construction & Rotor Cooling
GiroDisc manufactures its rotor friction rings from a proprietary high-carbon iron casting formulated to withstand the demands of performance braking.
During repeated high-speed stops, brake components experience significant thermal loads. The rotor's material composition and ventilation design play an important role in managing temperatures and maintaining predictable braking response.
Each GiroDisc A2-321 incorporates 48 internal curved cooling vanes engineered to draw air through the rotor as it rotates.
The curved vane design acts as a centrifugal pump, pulling cooling air through the internal passages to help dissipate heat from the iron friction ring.
This advanced cooling construction is designed to support consistent braking performance during spirited street driving and demanding performance applications.
Fully Floating Two-Piece Rotor Technology
The GiroDisc A2-321 features a fully floating two-piece construction consisting of a high-carbon iron friction ring attached to a lightweight aluminum mounting hat.
When braking temperatures increase, the iron rotor ring and aluminum hat expand at different rates. GiroDisc's floating mounting hardware allows controlled movement between these components to accommodate thermal expansion.
High-strength alloy steel drive pins connect the rotor ring to the aluminum hat while maintaining the intended assembly configuration.
Spring clips and spring washers help manage movement between the components and minimize unwanted rattling, providing the benefits of a floating rotor design with street-friendly operating characteristics.
Lightweight 6061-T6 Aluminum Mounting Hats
Each GiroDisc A2-321 rear rotor assembly uses a precision-machined 6061-T6 aluminum mounting hat with a black anodized finish.
The lightweight aluminum construction helps reduce unnecessary rotating and unsprung weight compared with heavier mounting designs.
Reducing unsprung mass can benefit suspension response, while minimizing rotating mass can contribute to more responsive vehicle dynamics.
Each complete GiroDisc A2-321 rear rotor assembly weighs approximately 18.4 pounds, according to the manufacturer's specifications.
Reusable Aluminum Hats & GiroDisc D2-321 Replacement Rings
One of the primary advantages of the GiroDisc A2-321 is its serviceable two-piece construction.
Rather than replacing the entire rotor assembly when the friction surface becomes worn, compatible replacement iron rings can be installed while retaining the original aluminum mounting hats, provided the hats remain in serviceable condition.
Compatible Replacement Rings: GiroDisc D2-321.
Minimum Rotor Thickness: 26mm.
GiroDisc recommends replacing rotor rings when they reach the specified minimum thickness or if a crack develops that extends to the outer edge of the friction ring.
Always inspect the aluminum hats, mounting hardware, and friction rings during servicing. Follow GiroDisc's replacement-ring installation instructions and hardware requirements.
Direct Replacement for Factory Audi Rear Iron Brake Rotors
The GiroDisc A2-321 is engineered as a direct replacement for the factory rear iron brake rotor assemblies on compatible Audi C8 S6, C8 S7, and D5 S8 vehicles.
The vehicle-specific configuration is intended to work with the corresponding original brake calipers and mounting arrangement.
These rotors are not designed as a direct replacement for Audi carbon-ceramic rear brake packages. Vehicles equipped with carbon-ceramic brakes require separate compatibility verification.
Installation Note: Follow GiroDisc's installation instructions and applicable Audi service procedures. Verify rotor orientation, brake pad condition, mounting hardware torque, and overall brake system operation before driving.
Frequently Asked Questions
Will GiroDisc A2-321 rear rotors fit my Audi C8 S6?
Yes. The GiroDisc A2-321 is designed for Audi C8 S6 models equipped with factory iron rear brakes. Confirm your vehicle's brake configuration and original rotor dimensions before ordering.
Are GiroDisc A2-321 rotors compatible with the Audi C8 S7?
Yes. GiroDisc lists the A2-321 as a rear brake rotor replacement for compatible Audi C8 S7 applications equipped with factory iron brakes.
Will these rotors fit the Audi D5 S8?
Yes. The Audi D5 S8 is included in the manufacturer's listed applications for GiroDisc A2-321 rear rotors, provided the vehicle uses the corresponding factory iron brake system.
Are GiroDisc A2-321 rotors for the front or rear?
The GiroDisc A2-321 assemblies are designed for the rear axle. The corresponding front rotor application is sold separately under GiroDisc part number A1-321.
Can these rotors replace Audi carbon-ceramic brake discs?
No. The A2-321 is listed as a direct replacement for factory iron rear brake rotors only. Compatibility with factory carbon-ceramic braking systems should not be assumed.
What size are the GiroDisc A2-321 rear brake rotors?
These rotors measure 350mm in outside diameter and 28mm in nominal thickness, with a minimum allowable thickness of 26mm.
How much does each GiroDisc A2-321 rear rotor weigh?
Each complete rear rotor assembly weighs approximately 18.4 pounds according to GiroDisc's published specifications.
Are GiroDisc A2-321 rear rotors fully floating?
Yes. The A2-321 features fully floating two-piece construction with high-strength steel drive pins, spring clips, and spring washers to accommodate thermal expansion while helping minimize unwanted hardware noise.
How many cooling vanes do GiroDisc A2-321 rotors have?
Each rotor features 48 internal curved cooling vanes designed to draw air through the assembly to help dissipate braking heat.
Can the rotor rings be replaced without purchasing new aluminum hats?
Yes. GiroDisc's two-piece construction allows worn friction rings to be replaced separately from the aluminum hats, provided the hats remain in suitable condition.
Which replacement rings fit GiroDisc A2-321?
The compatible replacement ring part number is GiroDisc D2-321. Confirm the replacement ring application and required hardware before ordering.
When should the GiroDisc A2-321 friction rings be replaced?
GiroDisc recommends replacement when the friction rings reach the minimum thickness of 26mm or when a crack extends to the edge of the ring.
Are these rear rotors suitable for performance driving?
Yes. Their high-carbon iron construction, advanced curved cooling vanes, and fully floating mounting design are intended for demanding performance driving conditions. Proper brake pad selection, brake fluid, and regular brake inspections remain essential.
Where are GiroDisc brake rotors manufactured?
GiroDisc manufactures its major rotor components, including aluminum hats, friction rings, and drive pins, in-house at its facility in Bellingham, Washington, USA.
Upgrade Your Audi S6, S7 or S8 with GiroDisc Rear Brake Rotors
Whether you're upgrading your Audi C8 S6, improving the rear braking performance of your C8 S7, or maintaining your D5 S8, GiroDisc A2-321 Two-Piece Floating Rear Brake Rotors provide advanced high-carbon iron construction, lightweight aluminum mounting hats, and fully floating performance engineering.
Featuring 350mm friction rings, 48 curved cooling vanes, and reusable aluminum hats, these GiroDisc rear brake rotors deliver a premium braking solution designed for Audi performance enthusiasts.