all

Audi RS3 Sedan (8V) Front Rotors The Girodisc 2-piece floating front rotor set is a direct replacement for the factory discs on the Audi RS3 Sedan (8V). These rotors bolt directly to the car with no modifications and maintain the original brake bias and ABS calibration. By replacing heavy factory rotors with lightweight performance units, you reduce unsprung and rotational mass for faster suspension response and improved acceleration. Each Girodisc rotor weighs approximately 24.0 lbs compared to the OEM’s 27.4 lbs, offering an immediate benefit in both feel and feedback. This upgrade delivers stronger braking performance on the street and consistent fade resistance on track days. Precision-Engineered Performance Vehicle Fitment Audi RS3 Sedan (8V) Audi RS3 Sportback (8V) Features Direct OEM replacement: Works with stock calipers and hardware—no modifications or adapters needed. Curved vane ventilation: Directional vanes act as a centrifugal pump, pulling cool air through the disc for improved heat dissipation. Floating mount hardware: Ten high-strength steel drive pins with anti-noise washers allow thermal expansion while eliminating rattle. Weight savings: Over 3 lbs lighter per rotor than OEM for improved throttle and suspension response. U.S.-built quality: Aluminum hats are machined from 6061-T6 billet; iron rings are cast and finished entirely in-house by Girodisc. FAQs Do these fit directly to the OEM calipers? Yes, they are a true bolt-on replacement for factory RS3 8V front rotors. What’s the benefit of two-piece rotors? Lower weight, faster cooling, and the ability to replace just the iron rings when worn. Will they make noise? No—the anti-noise washers ensure quiet operation during normal driving. Are these suitable for daily driving? Absolutely. They’re quiet and smooth on the street but strong enough for track use. How are they sold? Sold and priced per pair. Upgrade your RS3 Sedan with Girodisc floating rotors for cooler operation, reduced fade, and improved braking performance in every condition.

Chevrolet Camaro Z/28 (5th Gen) Front Iron Rotor Conversion The Girodisc Front Iron Rotor Conversion for the fifth-generation Chevrolet Camaro Z/28 provides a lightweight, high-performance alternative to the factory carbon-ceramic rotors. Designed as a direct replacement for the OE discs, this system bolts on with no permanent modifications required. For optimal performance and reasonable rotor weight, it requires brake pads with a swept area (annulus) of 66mm or less, using the FMSI #1405 pad shape. Performance and Design By switching from carbon-ceramic to iron rotors, drivers benefit from improved heat management, reduced replacement costs, and consistent braking performance under repeated heavy use. The Girodisc design maintains factory brake bias and ABS functionality while significantly improving serviceability. Features - Direct replacement for the OEM front carbon-ceramic rotors. - Requires the FMSI #1405 pad shape (available in multiple compounds). - Two-piece floating rotor assembly combines a proprietary cast iron friction ring with a precision-machined 6061-T6 aluminum hat. - Curved internal vanes act as a centrifugal pump to maximize cooling airflow through the rotor. - Floating mount system with 12 high-strength alloy steel drive pins allows axial and radial float to accommodate heat expansion and reduce stress. - Anti-noise spring washers eliminate the rattle typically associated with floating rotors during street use. - Cadmium-plated hardware ensures long-term corrosion resistance and durability. - Lightweight two-piece design lowers rotational and unsprung mass, improving acceleration, steering response, and suspension control. Specifications Rotor Type: Two-piece floatingMaterial: Proprietary cast iron with 6061-T6 aluminum hatPad Requirement: FMSI #1405 (66mm swept area or less)Mount Hardware: 12 high-strength alloy steel drive pins, class 12.9 cap screwsOrigin: Designed, cast, and machined in the USAFitment: Chevrolet Camaro Z/28 (5th Gen) FAQs: Chevrolet Camaro Z/28 (5th Gen) Front Iron Rotor Conversion Why do I need to use a different pad shape? The Girodisc rotors are optimized for a 66mm pad annulus to maintain ideal weight and thermal characteristics. The required pad shape is FMSI #1405. Can I reuse my OEM pads? No. The OEM pads are too large for the reduced swept area and may cause overheating or excessive wear. Will this affect my ABS or brake balance? No. The system retains the factory brake bias and integrates seamlessly with the stock calipers and ABS tuning. Are these rotors noisy? The use of spring washers in the floating mount design minimizes rattle and vibration while still allowing full float under thermal load. What happens when the rotors wear out? The aluminum hats are reusable; you only need to replace the cast iron friction rings and reassemble with new hardware. Ordering Information Sold and priced per pair. Includes left and right front Girodisc rotors for the Chevrolet Camaro Z/28 (5th Gen). Requires FMSI #1405 brake pads for installation.

Ford GT ('05–06) Front Rotors Upgrade your 2005–2006 Ford GT with Girodisc two-piece floating front rotors—precision-built to deliver the ultimate balance of lightweight performance and thermal efficiency. Designed as a direct replacement for factory rotors, these discs bolt on with no modifications and maintain OEM brake bias and ABS functionality while dramatically improving responsiveness and braking consistency. Track-Tested Performance, Street-Ready Reliability Each Girodisc rotor is engineered and manufactured in the USA using 6061-T6 aircraft-grade aluminum hats mated to proprietary cast iron rotor rings. The curved vane internal cooling design maximizes airflow, dissipating heat more efficiently to prevent warping and fade under extreme driving conditions. The floating mount system reduces noise while allowing the rotor to expand and contract naturally under heat cycles, ensuring longevity and precision feel. GiroDisc A1-043 Vehicle Fitment • 2005–2006 Ford GT (5.4L Supercharged V8) Girodisc A1-043 Features • Direct bolt-on replacement for OEM rotors• Two-piece floating design reduces unsprung and rotational mass• Proprietary high-carbon cast iron rotor rings• 6061-T6 aluminum hats machined in-house in the USA• Floating drive pin system with anti-noise spring washers• Enhanced heat dissipation and fade resistance• Sold/priced per pair GiroDisc A1-043 Ford GT Front Rotor FAQs Are these a direct replacement for OEM rotors? Yes, Girodisc rotors fit the factory calipers and require no modification. Will they help with brake fade? Absolutely. The curved vane design and two-piece construction improve cooling, reducing fade during track or spirited driving. Do they change pedal feel? Expect a firmer, more consistent pedal feel thanks to reduced unsprung weight and improved thermal stability. Can I reuse the hats? Yes, Girodisc replacement rings are available, allowing you to reuse the aluminum hats for cost-effective servicing. Experience world-class braking precision on your Ford GT with Girodisc rotors—engineered for drivers who demand perfection from every stop.

Porsche 997 GT3 Cup 380x34mm Front Rotors Girodisc 2-piece floating front rotors are a direct, high-performance replacement for the factory discs on all Porsche 997.2 GT3 and GT2 models, including Cup applications. Designed to bolt directly to the car and work with OEM calipers, they allow continued use of unmodified factory pads—unlike most aftermarket solutions for this platform. This upgrade maintains factory brake bias and ABS function while reducing weight, improving cooling, and enhancing overall braking consistency. Each assembly features a precision-machined 6061-T6 aluminum hat mated to Girodisc’s proprietary high-carbon cast-iron rotor rings. The 380x34mm curved vane design acts as a centrifugal pump, drawing cooling air through the disc for outstanding heat management and fade resistance under high-load track conditions. Every component is designed, cast, and machined in-house in the USA to exacting motorsport standards. Precision-Engineered Performance Vehicle Fitment Porsche 997.2 GT3 Porsche 997.2 GT2 Porsche 997 GT3 Cup Girodisc A1-126 Features Direct OEM replacement: Fits OEM calipers and hardware without modifications or special adapters. Curved vane design: 12 directional vanes circulate air through the rotor to manage temperature and prevent fade. Floating mount hardware: Cadmium-plated steel drive pins with anti-noise washers allow for thermal expansion and eliminate rattling. Lightweight two-piece construction: Reduces unsprung and rotational mass for sharper steering and faster response. Serviceable system: Replace only the cast-iron rings when worn while reusing the aluminum hats. Made in the USA: All Girodisc rotors are designed, cast, and machined domestically for uncompromising precision. Girodisc A1-126 FAQs Can these be used with factory brake pads? Yes, Girodisc rotors are designed to accept OEM pads with no modification required. Are they compatible with OEM PCCB systems? Yes, they replace PCCB rotors directly while maintaining stock brake bias and performance balance. Do these rotors make noise? No, anti-noise spring washers eliminate the rattling common to floating designs. Are they track-ready? Absolutely. Girodisc rotors are built to perform under extreme heat cycles on street or track. How are they sold? Sold and priced per pair. Upgrade your Porsche 997 GT3 or GT2 with Girodisc’s 380x34mm floating rotors for improved cooling, reduced fade, and race-proven durability—perfect for both spirited street driving and competitive track use.

D1-156 Girodisc Front Replacement Rotor Rings REPLACEMENT ROTOR RINGS AND INSTALLATION HARDWARE ONLY. DOES NOT INCLUDE ALUMINUM HATS. Competition Motorsport is an authorized dealer for Girodisc products and we are one of the largest stocking dealers in the country.We ship most products same or next business day to ensure we meet your delivery deadline. The Girodisc replacement rotor system is a direct rotor disc replacement for the Girodisc 2-piece hat and rotor and no modifications are necessary. The rotor and hat mount together through a floating mount system which utilizes 8-10 high strength alloy steel drive pins manufactured by Girodisc in the USA to their own specifications and are cadmium plated for corrosion resistance.The alloy drive pins transfer the load from braking while maintaining the axial and radial float between the disc rotor and hat.The pins are secured by grade 12 cap screws with hardened washers and mounted with anti-noise spring washers to allow for heat expansion while eliminating the rattle and noise associated with floating rotors. The 2-piece Girodisc design allows for rotor only replacement to minimize replacement costs and deliver outstanding performance and cooling. Sold/priced per pair.

D1-159 Girodisc McLaren 394mm Front Replacement Rings Renew your McLaren’s braking performance with Girodisc D1-159 394mm front replacement rings. These precision-engineered components bolt directly to your existing Girodisc aluminum hats using the supplied floating hardware kit. Each ring is machined from Girodisc’s proprietary high-carbon cast iron for superior thermal control, balanced response, and fade-free braking under extreme track conditions. Vehicle Fitment Compatible with:• McLaren 540C / 570S / 570GT / 600LT (Front)• McLaren 650S / 675LT (Front)• McLaren MP4-12C (Front)Note: Designed for Girodisc 394mm two-piece front rotor systems. Not compatible with OEM carbon-ceramic rotors or one-piece iron discs. Features • Sold as a left/right pair with complete floating hardware kit• Direct replacements for Girodisc 394mm two-piece front rotors• CNC-machined from high-carbon cast iron for durability and high-temperature stability• Directional curved vanes accelerate airflow for maximum cooling efficiency• Maintains factory brake bias, ABS, and stability control calibration• Precision-balanced for smooth, vibration-free operation• Designed exclusively for Girodisc aluminum hats used in McLaren iron-conversion systems Specifications • Diameter: 394 mm• Position: Front• Material: High-carbon cast iron• Mount type: Floating two-piece system• Includes: Two rotor rings and new hardware kit• Sold/priced per pair Girodisc D1-159 McLaren 394mm Front Replacement Ring FAQs Can I use these with McLaren’s OEM carbon-ceramic rotors? No. These are for Girodisc steel rotor conversions only and will not fit OEM ceramic brake hardware. What pad compounds are best suited for these rotors? For street/track mix, Pagid RS29 or Ferodo DS2500 pads are excellent. For full track duty, Pagid RSL1 or Endless ME20 are ideal high-temp options. Are these rotors directional? Yes. Each rotor is marked for left and right orientation to ensure the curved vanes channel airflow correctly through the disc for optimal cooling. What’s the service life of these rotors under track use? Typically 20–30 hours of hard circuit time depending on track layout, pad compound, and cooling efficiency. Street-driven cars often exceed 40,000 miles. Upgrade your McLaren’s braking precision with Girodisc D1-159 394mm front replacement rings — race-bred components engineered for stability, cooling, and performance at any speed.

D1-023 Girodisc McLaren Front Rings Keep your McLaren’s world-class braking performance sharp with Girodisc D1-023 380mm front replacement rings. These precision-engineered rotors are direct replacements for Girodisc two-piece systems and bolt to your existing aluminum hats using the supplied floating hardware kit. Each ring is machined from Girodisc’s proprietary high-carbon cast iron, offering exceptional thermal capacity, improved pedal feel, and consistent stopping power during both spirited road driving and track use. Vehicle Fitment Compatible with:• McLaren 12C / MP4-12C• McLaren 650S / 675LT• McLaren 540C / 570S / 570GT / 600LTNote: Designed exclusively for Girodisc 380mm two-piece front rotor systems. Not compatible with OEM carbon-ceramic or one-piece iron rotors. Features • Sold as a left/right pair with complete floating hardware kit• Direct replacements for Girodisc 380mm two-piece front rotors• CNC-machined from high-carbon cast iron for stability and heat control• Directional curved vanes optimize airflow for superior cooling• Maintains OEM brake bias, ABS, and traction control calibration• Precision-balanced for vibration-free operation• Designed exclusively for Girodisc aluminum hats Specifications • Diameter: 380 mm• Position: Front• Material: High-carbon cast iron• Mount type: Floating two-piece system• Includes: Two rotor rings and complete hardware kit• Sold/priced per pair Girodisc D1-023 McLaren 380mm Front Ring FAQs Can these be installed with factory McLaren rotor hats? No. The D1-023 rings are designed exclusively for Girodisc aluminum hats and are not compatible with OEM carbon-ceramic or iron rotors. Do these rings improve braking compared to OEM steel rotors? Yes. The floating two-piece design improves heat dissipation, reduces unsprung mass, and enhances braking consistency under heavy load. What brake pads pair best with these rotors? For street and occasional track driving, Ferodo DS2500 or Hawk HPS 5.0 offer excellent balance. For dedicated track use, Pagid RS29 or Carbotech XP12 pads provide high-temperature stability and fade resistance. What torque should I use for installation hardware? Torque all fasteners to 12 ft-lbs (16 Nm) with blue Loctite. After one full heat cycle, recheck torque to confirm proper float and secure alignment. Upgrade your McLaren’s braking system with Girodisc D1-023 380mm front replacement rings — engineered for peak performance, thermal control, and consistent braking feel lap after lap.

Audi B7 RS4 380mm Front Rotors Girodisc 380mm front rotors give the Audi B7 RS4 a substantial braking upgrade without requiring a big brake kit. These 2-piece floating rotors are a direct replacement for the factory discs and include caliper spacers for perfect fitment. With a larger diameter than OEM (380mm vs. 365mm), they deliver greater braking torque, improved heat capacity, and a lighter overall feel at the pedal—ideal for both aggressive street driving and full track use. Each rotor combines a 6061-T6 aluminum hat with Girodisc’s proprietary high-carbon cast-iron rotor rings, all machined in-house in the USA. The internal curved vane design functions like a centrifugal air pump, drawing cooling air through the rotor to stabilize temperatures under repeated hard stops. The result: better braking control, reduced fade, and longer pad life. Big Stopping Power, No Big Brake Kit Required Vehicle Fitment Audi B7 RS4 (2006–2008) Girodisc A1-100 Features Direct bolt-on upgrade: Includes caliper spacers for easy installation—no additional modifications needed. 380mm rotor diameter: Increases brake torque and thermal capacity over stock 365mm discs. Lightweight 2-piece construction: Reduces unsprung and rotational mass for sharper handling response. Curved vane cooling system: Actively circulates air through the rotors to minimize fade during repeated stops. Floating hardware design: Allows thermal expansion without distortion for consistent pad contact. Made in the USA: Machined and assembled entirely in-house by Girodisc. Girodisc A1-100 FAQs Do these rotors fit directly to the factory RS4 calipers? Yes. They include caliper spacers and hardware to bolt up perfectly to OEM calipers. Are these rotors lighter than OEM? Yes. At approximately 22.6 lbs per rotor vs. 25.5 lbs stock, they reduce unsprung mass and rotational inertia. Do they improve braking performance? Absolutely. The increased size and advanced vane design provide stronger, more consistent braking under heat. Do I need any special modifications? No. Installation is straightforward—just use the included caliper spacers. How are they sold? Sold and priced per pair. Give your Audi RS4 sharper, cooler, and more confident stopping power with Girodisc 380mm front rotors—engineered for precision and performance without compromise.

McLaren 380mm Front Rotors, incl. spacers Unlock consistent, repeatable stopping power with Girodisc two-piece floating front rotors for McLaren models originally equipped with 370mm cast-iron front discs. This upgrade increases diameter to 380mm and includes the required caliper spacers for a true bolt-on installation. You keep factory brake bias and ABS while gaining cooling capacity, lighter rotating mass, and sharper pedal feel. Race-Bred, Street-Refined Each rotor pairs a U.S.-sourced 6061-T6 aluminum hat with Girodisc’s proprietary high-carbon cast-iron ring. Curved internal vanes act like a centrifugal pump to move cooling air through the disc under hard use. The fully floating mount system controls thermal growth, helping the rotor self-center between pads and maintain quiet street manners via anti-noise spring/Belleville washers. Features Diameter upgrade: 370mm → 380mm for more torque leverage and thermal headroom Direct fit: Includes caliper spacers; uses factory calipers and pad shape Two-piece floating design: Reduces unsprung/rotational mass and improves consistency Curved directional vanes: Efficient internal airflow for superior heat management Serviceable: Replace rings later and reuse the hats to lower long-term cost Premium hardware: 12 cadmium-plated alloy steel drive pins with class 12.9 cap screws and hardened washers Made in the USA: Hats and rings machined in-house for precise fit Vehicle Fitment For McLaren applications originally equipped with 370mm cast-iron front rotors (non-CCM). Examples include: McLaren MP4-12C (iron brake package) McLaren 650S (iron brake package) Other McLaren models using 370mm iron front rotors Note: Not for factory carbon-ceramic (CCM) brake packages. If you’re unsure, send your VIN and a brake photo—we’ll verify fitment before you order. What’s Included (2) Pre-assembled 380mm two-piece floating front rotors (left/right) (2) Caliper spacers sized for 380mm conversion Mounting/torque guidance and bedding procedure Girodisc A1-023 Technical Specifications Part Number: A1-023 Position: Front Rotor Diameter: 380mm (upgrade from 370mm) Construction: Two-piece, fully floating Hat Material: 6061-T6 aluminum (anodized) Ring Material: High-carbon cast iron Vanes: Curved, directional Hardware: 12 drive pins, class 12.9 fasteners, spring/Belleville washers Sold/Price: Per pair Installation & Bedding Clean hub faces thoroughly; remove rust and debris. Install rotors and supplied caliper spacers; torque fasteners to spec. Bed pads: several medium stops 60→10 mph, then a few hard stops 80→20 mph. Drive to cool with minimal braking. Girodisc A1-023 FAQs Do I need different pads? No—these retain the factory caliper and pad shape. Choose a compound appropriate for street or track. Will they rattle? The floating hardware uses anti-noise spring/Belleville washers to maintain quiet operation while allowing thermal float. Are replacement rings available? Yes. When the rings reach minimum thickness or crack to an edge, replace the rings and reuse the hats/hardware. Street and track use? Absolutely. Pair with quality pads and high-temp fluid for track days; they’re refined enough for daily use. Step up to Girodisc 380mm rotors for cooler temps, stronger bite, and repeatable braking—without changing your calipers.

Corvette C5, C6 Z51 Front Rotors Transform your Corvette’s braking performance with Girodisc 2-piece 340mm front rotors—precision-engineered for the C5 and C6 Z51 brake setup. Whether you’re replacing worn OEM rotors or converting your base model to the Z51 brake package, these lightweight, fully floating rotors provide stronger, more consistent braking with less unsprung weight and improved cooling efficiency. Designed as a direct replacement for the OEM 340mm Z51 rotor (also known as the “J55” heavy-duty package), each Girodisc assembly weighs just 20.7 lbs per rotor—saving valuable rotational mass. The hats are machined from 6061-T6 aluminum and anodized for durability, while the cast-iron rotor rings feature Girodisc’s proprietary high-carbon alloy for superior thermal management and strength under repeated high-load stops. Precision Performance for Street and Track Corvettes Vehicle Fitment Corvette C6 Z51 (340mm front rotors) Corvette C5 and C6 Base (with Z51 caliper bracket GM #88964166 or equivalent) Girodisc A1-096 Features Direct-fit upgrade: Bolts directly to OEM or Z51 caliper setup with optional bracket. Lightweight 2-piece construction: Weighs only 20.7 lbs per rotor vs. heavier one-piece OEM rotors. Proprietary high-carbon cast iron: Delivers exceptional strength, heat tolerance, and durability under track conditions. Curved vane design: 48 internal vanes pull cooling air through the rotor for improved fade resistance. Floating mount system: Spring clips and Belleville washers allow controlled float for quiet, consistent braking. Made in the USA: All components machined, finished, and assembled in-house by Girodisc in Bellingham, WA. Specifications Diameter: 340mm Thickness: 32mm (replace at 30mm minimum) Weight: 20.7 lbs per rotor Girodisc A1-096 FAQs Can these rotors be used on a C5 or base C6? Yes. You’ll need the Z51 front caliper bracket (GM #88964166) or equivalent to complete the conversion. Are these rotors lighter than OEM? Yes. At just 20.7 lbs each, they reduce unsprung and rotational mass for quicker handling response. Are replacement rotor rings available? Yes. Replacement rings (part number D1-096) can be installed on the same hats when needed. Do these work for both street and track? Absolutely. Girodisc rotors are engineered for quiet street use and high-performance track reliability. When should I replace the rings? Replace at or below 30mm thickness, or if any crack reaches the edge of the ring. Step up your Corvette’s braking performance with Girodisc 340mm front rotors—lightweight, durable, and engineered for precision on both street and circuit.

Girodisc 1740 Brake Pads The Girodisc 1740 provides improved bite, smooth modulation, and consistent braking for Porsche drivers who want enhanced performance without excessive dust or noise. Ideal for spirited road use, these pads offer excellent cold bite and stable friction while remaining quiet and easy to control. They are a direct-fit option for Girodisc 2-piece rear rotor systems. Fits the Following Vehicles: Make Model Build (Year) Front Rear Porsche 918 Spyder 13 - 15 X Porsche 991 GT3 [ceramic brakes] 15 - 18 X Porsche 991 GT3 [iron brakes] 15 - 18 X Porsche 991 GT3 RS [ceramic brakes] 15 - 18 X Porsche 991 GT3 RS [iron brakes] 15 - 18 X Porsche 991 Turbo [ceramic brakes] 13 - X Porsche 991 Turbo [iron brakes] 13 - X Porsche 991 Turbo S [ceramic brakes] 13 - X Porsche 991 Turbo S [iron brakes] 13 - X Porsche 991.2 GT2 RS [ceramic brakes] 18 - X Porsche 991.2 GT3 [ceramic brakes] 18 - X Porsche 991.2 GT3 [iron brakes] 18 - X Porsche 991.2 GT3 RS [ceramic brakes] 18 - X Porsche 991.2 GT3 RS [iron brakes] 18 - X Porsche 991 R [ceramic brakes] 16 - X Porsche 991 911 Speedster [iron brakes] 19 - X Porsche 992 3.0 Carrera 4S [ceramic brakes] 18- X Porsche 718 Cayman GT4 4.0 [982] [cast iron brakes] 19 - X Porsche 718 Cayman GT4 4.0 [982] [ceramic brakes] 19 - X Porsche Cayman GT4 [981] 16 - X Porsche Cayman GT4 [981] [ceramic brakes] 16 - X Porsche 992 Turbo [iron brakes] 2020 - X Porsche 992 GT3 [iron brakes] 2021 - X Porsche 992 Carrera S [ceramic brakes] 2018 - X Porsche 992 GT3 [ceramic brakes] 2021 - X Porsche 992 Turbo [ceramic brakes] 20 - X Porsche 718 Cayman GT4 4.0 RS [982] [cast iron brakes] 21 - X Porsche 718 Cayman GT4 4.0 RS [982] [ceramic brakes] 21 - X Note: Designed specifically for Girodisc rear two-piece steel rotors, not PCCB systems. GiroDisc GP10 Compound refined for the street but built to perform Designed for performance-minded drivers, the GP10 semi-metallic brake pads strike the perfect balance between daily drivability and occasional track use. Optimized for street conditions, they offer a quiet, lower-dust experience without sacrificing the confident stopping power you need when the pace picks up. Whether you're navigating traffic or hitting the occasional track day, these pads deliver a responsive pedal feel, excellent heat resistance, and consistent braking performance. Built for longevity and reliability, they’re the ideal upgrade for enthusiasts who want everyday comfort with the capability to push harder when it counts. For drivers planning extensive track sessions or more aggressive track driving, we recommend considering our dedicated race pads, engineered to handle the extreme heat and demands of frequent high-performance track use. GiroDisc GP30 Compound - endurance race pad Our GP30 compound is an all-around endurance race pad. The GP30 is designed to work with street car ABS as well as motorsport-grade ABS found in factory-built race cars. These pads work with a wide range of tires, from DOT street tires to R-compounds to full race slicks. GiroDisc GP35 Compound - A race pad for all occasions Our GP35 compound combines the best of both worlds into one all-around race pad. We took some of the longevity of our endurance pads, some of the bite of our sprint pads, and worked to develop a compound that can do it all. As a bonus, it’s easy to bed, which means less time figuring your brakes out, and more time driving on the track. The GP35 is designed to work with street car ABS as well as motorsport-grade ABS found in factory-built race cars. The torque curve is designed to be smooth and linear, which leads to superior modulation and release under trail braking. These pads work with a wide range of tires, from DOT street tires to R-compounds to full race slicks. It has become our most popular compound and is the compound we recommend most frequently to track day drivers and shops running cars in professional racing series. Note: this compound is only compatible with iron rotors. GiroDisc 1740 Features • High-performance street-focused compound• Low dust and reduced noise levels• Strong cold bite for daily street use• Smooth, predictable pedal modulation• Stable friction across a broad temperature range• Direct-fit for Girodisc rear brake systems• Sold/priced per rear axle set GiroDisc 1740 Specifications • Compound: GP10 Street Performance• Position: Rear• Compatibility: Girodisc steel rotors• Operating Range: Optimized for street temperatures• Includes: One complete set of rear brake pads Girodisc 1740.18 Rear Pad FAQs Are these pads quiet enough for daily use? Yes. The GP10 compound is engineered to minimize noise and vibration while delivering excellent braking feel. Can these pads be used with OEM Porsche rotors? While they may physically fit, they are optimized for performance and wear when paired with Girodisc two-piece rotors. Are these suitable for track days? They can handle light HPDE use, but for full track sessions a more aggressive compound like Girodisc GP30 or the best selling GP35 are recommended. Do these pads create less dust than OEM pads? Yes. GP10 pads produce noticeably less dust, helping keep your wheels cleaner. How do these compare to factory Porsche performance pads? GP10 pads offer smoother modulation, better cold bite, and significantly reduced dust, making them ideal for spirited street driving. Enhance your Porsche's rear braking confidence with Girodisc GP10 Street Pads GP10-1740.18 — engineered for clean, quiet, and consistent performance.

Pagid Racing Brake Pad Shape 4938 Pagid 4938 Brake Pad Fitment Guide Make Model Build (Year) Front Rear Audi RS6 (C7) [ceramic brakes] 13 - 18 X Audi S6 [ceramic brakes] 12 - X Audi S7 [ceramic brakes] 12 - X Bentley Continental GT [ceramic brakes] 11 - X Bentley Mulsanne [ceramic brakes] 10 - X Pagid Racing Brake Pads are engineered for high-performance driving, delivering exceptional stopping power, durability, and control under the most demanding conditions. Trusted by professional racers and performance enthusiasts worldwide, these pads are crafted using advanced friction materials and cutting-edge technology to ensure consistent performance, low fade, and excellent modulation. Whether you're on the track or tackling aggressive street driving, Pagid Racing Brake Pads provide the reliability and confidence you need to push your vehicle to its limits. Pagid RSC 1 Compound (Ceramic Rotors Only) A race and track day compound for all known types of ceramic brake discs, RSC 1 is a low metallic resin bonded material containing steel and aramid fibers. This material features good all-round characteristics and is suitable for all types of usage.

Pagid Racing Brake Pad Shape No. 4304 Fits the Following Vehicles (FMSI D031): Make Model Build (Year) Front Rear Alfa Romeo Berlina 1.75 2.0 68 - 77 X Alfa Romeo Giulia 1.3/1.6 66 - 76 X Audi 50 74 - 79 X Audi 60/75 66 - 72 X Audi 100 68 - 74 X X BMW 1600 Ti/1800 Ti/TiSA 63 - 71 X BMW M1 [non Procar] 78 - 82 X BMW M1 Procar 78 - 82 X Ferrari 308GT4/GTB/GTS 2 valve 73 - 85 X Ferrari Dino 246 GTB/GTS 68 - 75 X Hyundai i30 N TCR race car [Brembo caliper] 17 - X Lamborghini Countach 74 - 91 X Lancia Stratos 74 - 75 X Mercedes 190-300 (W108-W115) 59 - 71 X Mercedes 200-300 (W123) 76 - 85 X Mercedes 250-280 (W114) 71 - 76 X Mercedes 280-450 (W116) 72 - 80 X Opel Ascona A 70 - 75 X Opel Commodore B 72 - 77 X Opel GT 69 - 73 X Opel Kadett B 1.5/1.9/ Kadett C 67 - 79 X Porsche 356 1.6 C/SC 63 - 66 X Porsche 904 Carrera GTS + 904/6 63 - 65 X Porsche 911 2.0 -2.8 S-Calipers 64 - 73 X Porsche 911 2.0 M-Calipers 65 - 69 X Porsche 911 2.7 / 3.0 / 3.2 Carrera 72 - 89 X Porsche 911 S 72 - 83 X Porsche 912 65 - 70 X Porsche 914/4 70 - 72 X Porsche 914/6 70 - 72 X X Saab 99 67 - 74 X Talbot Simca 1000 Rallye II+III 72 - 81 X VW Golf 1.1/1.3/1.6 GTI 75 - 83 X Hyundai Veloster N TCR 18 - X   Pagid Racing Brake Pads are engineered for high-performance driving, delivering exceptional stopping power, durability, and control under the most demanding conditions. Trusted by professional racers and performance enthusiasts worldwide, these pads are crafted using advanced friction materials and cutting-edge technology to ensure consistent performance, low fade, and excellent modulation. Whether you're on the track or tackling aggressive street driving, Pagid Racing Brake Pads provide the reliability and confidence you need to push your vehicle to its limits. Pagid Racing Brake compounds are for steel (cast iron) rotors only unless otherwise noted. RS 14 Compound: The Pagid RS 14 (Black) is a high friction value ceramic compound with very good modulation and high fade resistance. A very popular, aggressive pad with strong initial bite and high torque. In addition to the track-day environment, RS14 has shown success in short- to medium-distance circuit racing as well as gravel and tarmac rallying. RSL 29 Compound: The Pagid RSL 29 (Yellow) is the world-leading endurance brake pad used by most of the winning teams in motorsport. Although designed primarily for endurance racing, many competitors use this material successfully for sprint and short distance races also. RS29 has also found favor in the growing track day market due to the level of control, good cold performance, long life and low disc wear. Pagid RS 44 Compound: The Pagid RS 44 (Orange) is a carbon-based, highly controllable pad with a progressive friction curve. It has a medium initial bite and good low temperature response. A very versatile pad for use on both front and rear axles, or in conjunction with RS14 on the front axle in FWD cars. Particularly popular in Porsche club racing, fitted as OEM on the Porsche 993 RS and GT2. Pagid RSH 3 Compound: The RSH 3 is an organic compound optimized for sprint races with historic cars. Due to its perfect combination of braking characteristics, RSH 3 is offered over a wide range of applications. It is especially popular for its high initial bite and excellent modulation and release characteristics. Useable for rally, GT, and touring cars for professional circuit racing and also for club racing. Pagid RSH 42 Historic Compound: The characteristics of Pagid RSH 42 make this material appropriate for small formula cars. Furthermore you can use it as rear axle compound in combination with the RSH 29E on the front axle. An excellent classic rally pad which is also very popular in small formula cars. RSH 29E Compound: The RSH 29E is excellent for endurance racing with historic cars. It convinces with its long pad and disc life and requires less pedal effort during the race. A further advantage is the constant friction level over a wide range of temperatures. Typical applications are GT and touring cars in endurance races. Due to its friction level, you can use it in sprint races as well.

Pagid Racing Brake Pad Shape 2405 Pagid 2405 Brake Pad Fitment Guide Make Model Build (Year) Front Rear Porsche 996 3.4 Carrera Cup 99 - 01 X Porsche 996 3.6 Carrera 4S 03 - 05 X Porsche 996 GT2 02 - 05 X Porsche 996 GT3 02 - 05 X Porsche 996 GT3 Cup 02 - 05 X Porsche 996 GT3 RS [street car] 03 - 05 X Porsche 996 Turbo 99 - 05 X Porsche 997 3.8 Carrera S & 4S 05 - 12 X Porsche 997 3.8 Carrera GTS 09 - 11 X Porsche Boxster [987] [ceramic brakes] 05 - 12 X Porsche Cayman [987] [ceramic brakes] 06 - 12 X Porsche Cayman S [981] [ceramic brakes] 13 - X Porsche 718 Cayman [982C] [ceramic brakes] 16 - X Porsche 718 Cayman S [982C] [ceramic brakes] 16 - X Porsche 718 Cayman T [982C] [ceramic brakes] 19 - X Porsche 718 Cayman GTS [982C] [ceramic brakes] 17 - 20 X Porsche 718 Cayman GTS 4.0 [982C] [ceramic brakes] 20 - X Porsche 718 Boxster [982] [ceramic brakes] 16 - X Porsche 718 Boxster S [982] [ceramic brakes] 16 - X Porsche 718 Boxster T [982] [ceramic brakes] 19 - X Porsche 718 Boxster GTS [982] [ceramic brakes] 17 - 20 X Porsche 718 Boxster GTS 4.0 [982] [ceramic brakes] 20 - X Porsche 718 Spyder [982] [ceramic brakes] 19 - X Porsche 718 Cayman T [982C] [ceramic brakes] 19 - X Pagid Racing Brake Pads are engineered for high-performance driving, delivering exceptional stopping power, durability, and control under the most demanding conditions. Trusted by professional racers and performance enthusiasts worldwide, these pads are crafted using advanced friction materials and cutting-edge technology to ensure consistent performance, low fade, and excellent modulation. Whether you're on the track or tackling aggressive street driving, Pagid Racing Brake Pads provide the reliability and confidence you need to push your vehicle to its limits. The Pagid 2405 is a common Porsche fitment in either the front or the rear, depending on the model. Pagid Racing Brake compounds are for steel (cast iron) rotors only unless otherwise noted. Pagid Racing 2405 Brake Pad RS 14 Compound The Pagid RS 14 (Black) is a high friction value ceramic compound with very good modulation and high fade resistance. A very popular, aggressive pad with strong initial bite and high torque. In addition to the track-day environment, RS14 has shown success in short- to medium-distance circuit racing as well as gravel and tarmac rallying. Pagid Racing 2405 Brake Pad RSL 19 Compound Pagid RSL 19 is a low metallic resin bonded material containing steel and aramid fibers. It maintains a constant friction level across a broad range of temperatures. The material features very good modulation and release characteristics. Rear axle usage in combination with RSL 1 or RSL 2 on the front axle in heavier cars (GT3/GTE). Front axle usage for lighter GT and touring cars. Pagid Racing 2405 Brake Pad RSL 29 Compound The Pagid RSL 29 (Yellow) is the world-leading endurance brake pad used by most of the winning teams in motorsport. Although designed primarily for endurance racing, many competitors use this material successfully for sprint and short distance races also. RS29 has also found favor in the growing track day market due to the level of control, good cold performance, long life and low disc wear. Pagid Racing 2405 Brake Pad RS 44 Compound The Pagid RS 44 (Orange) is a carbon-based, highly controllable pad with a progressive friction curve. It has a medium initial bite and good low temperature response. A very versatile pad for use on both front and rear axles, or in conjunction with RS14 on the front axle in FWD cars. Particularly popular in Porsche club racing, fitted as OEM on the Porsche 993 RS and GT2. Pagid Racing 2405 Brake Pad RSC 1 Compound (Ceramic Rotors Only) A race and track day compound for all known types of ceramic brake discs, RSC 1 is a low metallic resin bonded material containing steel and aramid fibers. This material features good all-round characteristics and is suitable for all types of usage. Pagid Racing 2405 Brake Pad RSL 1 Compound Used in GT cars, touring cars and prototype endurance racing. Due to the high friction and good modulation, often used in sprint races as well. RSL 1 is a low metallic resin bonded material containing steel and aramid fibers with very high heat resistance. It maintains a constant friction level over a wide range of temperatures. Its reduced wear rate and disc friendliness make this material appropriate for endurance races. Pagid Racing 2405 Brake Pad RST 3 Compound RST 3 is a medium-high friction metal-ceramic compound containing steel fibers and is therefore the perfect complement of the RST product family. It captivates by its low heat conductivity. Rally tarmac and gravel, GT cars, touring cars and prototype circuit racing, formula cars and club racing. Wide range of applications due to it‘s combination of bite, friction and controllability.

Ferodo FRP3170 Rear Brake Pads Designed to handle the high-performance demands of modern sports cars, Ferodo Brake Pads deliver consistent, fade-free stopping power. Ferodo is an OEM supplier to the world's leading car manufacturers, and are used by many of the top names in motorsports. The Ferodo Racing pad range are produced in Mondovi, Italy and  include the most advanced braking materials available in the world. Ferodo Brake Pad Coefficient of Friction (Mu) Comparison Chart Ferodo Brake Pad Operating Temperature Comparison Chart Compatibility – Will They Fit Your Car?  The Ferodo FRP3170 Rear Brake pad will fit the following applications: Corvette C8 Z06 Iron Disc (J56) Rear Ferodo Racing Brake Pads Comparison Guide Choosing the right Ferodo race pad depends entirely on how often you plan to track your car and what performance characteristics matter most to you. We're asked daily for a recommendation between Ferodo DS2500, DS1.11, and DS3.12 brake pads—and with good reason. These three compounds cover nearly every use case, from daily-driven sports cars to championship-winning racecars. All three of these compounds are classified as Ferodo racing brake pads, not street pads, and each excels in specific areas such as fade resistance, torque stability, rotor wear, cold bite, and pad longevity. Whether you're heading to your first HPDE event or racing wheel-to-wheel in GT endurance, this guide helps you identify which Ferodo compound best matches your needs. Ferodo Racing Brake Pad Comparison – DS3.12 vs DS1.11 vs DS2500 Compound Key Strengths Best For Notes Ferodo DS3.12 - Flattest torque curve tested- High mu with less pedal pressure- Unfadeable at racing temps- Long-lasting and disc-friendly Club racing, time trials, HPDE, endurance racingGreat for high-horsepower, heavy cars with aero and slicks Designed for modern track demandsExceptional pedal consistencyQuickly becoming the new gold standard in race compounds Ferodo DS1.11 - Endurance-proven durability- Flat torque curve across wide temps- Easy on rotors- Fade-resistant and long-lasting Endurance racing, club racing, HPDEIdeal for drivers who want consistency and long wear life Slightly lower bite than DS3.12Excellent option for long stints and heavy use Ferodo DS2500 - Hybrid street/track performance- Good cold bite and manners- Moderate noise and dust- Flat torque curve during aggressive driving Dual-purpose driving, canyon runs, autocross, light track useExcellent for HPDE on street tires May wear quickly on heavy cars with race tiresOne of the best value pads for enthusiast drivers Ferodo Brake Pad Fade Resistance & Max Operating Temperature DS3.12: Unmatched fade resistance, withstanding 1600°F+ on dyno tests with zero fade. The top choice for pro-level racing and extreme track duty. DS1.11: Excellent fade resistance with a slightly lower max temp than DS3.12. Ideal for endurance racing and high-speed circuits. DS2500: Superior to any street/sport pad for fade, but not suited to heavy race use with slicks. Perfect for dual-purpose and HPDE cars on street tires. Ferodo Brake Pad Pad Life & Durability DS3.12: The most durable in the Ferodo lineup, offering ~15% more pad life than DS1.11. Built for endurance racing. DS1.11: Long-lasting with excellent disc friendliness when bedded properly. DS2500: Less durable in high-heat racing environments but adequate for light track use and daily driving. Ferodo Brake Pad Feel, Feedback & Torque Curve DS3.12: Very high mu (coefficient of friction), "grabby" feel, and ultra-consistent torque curve—loved by pros for its predictability. DS1.11: Moderate mu with a slightly declining torque curve under heat. Offers a more progressive feel, especially on street tires. DS2500: Lowest mu of the three. Feels more like a high-performance street pad with smoother torque, great for HPDE and mixed-use driving. Ferodo Brake Pad Manners (Cold Bite, Noise, Dust) DS2500: Best manners of the group. Low noise, moderate dust, and excellent cold bite—perfect for street-to-track use. DS3.12: Low cold bite but quiet when bedded properly. Moderate dust, easy to clean. DS1.11: Noisy when cold, less suitable for street use. Moderate cold performance with reduced disc wear vs. DS3.12. Ferodo Brake Pad Price vs. Value DS3.12: Premium price, but long life and consistency reduce overall cost per mile. DS1.11: Slightly lower cost than DS3.12 with similar longevity. A great value for endurance racers. DS2500: Incredible value as a true dual-purpose pad that rivals many OEM replacements in price while offering track-capable performance. Ferodo Brake Pad Product Highlights Track-proven compounds: DS2500, DS1.11, and DS3.12 trusted by drivers from HPDE to GT racing Fade-resistant up to 1600°F+ with zero performance loss (DS3.12) Endurance-grade wear life with low disc wear and consistent performance Excellent pedal feel and torque modulation across a wide temperature range Made for serious motorsports—from weekend warriors to pro race teams Ferodo Brake Pad Frequently Asked Questions (FAQ) 1. Can I daily drive on Ferodo DS2500 brake pads? Yes. The DS2500 offers excellent manners on the street and solid performance on the track, making it a top choice for dual-purpose applications. 2. Is DS3.12 too aggressive for street tires? It can be. DS3.12 has a high mu and strong initial bite, which may activate ABS more frequently with street tires. Best used with slicks or R-compounds. 3. Which Ferodo pad is best for endurance racing? DS3.12 and DS1.11 are both endurance compounds, but DS3.12 offers longer life and more consistent torque at extreme temps. 4. Are Ferodo race pads noisy? DS2500 is very quiet. DS3.12 is relatively silent when bedded properly. DS1.11 can be noisy, especially when cold. 5. What’s the best pad for HPDE beginners? DS2500 is ideal for beginners using street tires and moderate track use. XP8 (from Carbotech) is another great option if more bite is needed. 6. Do Ferodo pads require bedding? Yes. Proper bedding ensures maximum performance, even pad wear, and rotor compatibility. Always follow the Ferodo bedding procedure included with your pads. How to Bed In Ferodo Racing Brake Pads (DS2500, DS1.11, DS3.12) Properly bedding in your Ferodo Racing brake pads ensures optimal performance, pad longevity, and rotor compatibility. Whether you're using Ferodo DS2500 for HPDE or DS3.12 and DS1.11 for professional-level endurance racing, following a structured bedding procedure is critical. Below is a simplified step-by-step chart to guide the break-in process. Step Description 1. Safety First Never perform the following activities on public roads but rather ensure you are in a safe and controlled environment such as a skidpad or racetrack for bedding in.  2. Initial Bedding Heat Cycles Perform 5 moderate stops from 60 mph to 10 mph without engaging ABS. Do not come to a complete stop. Allow light rolling between applications to avoid pad imprinting. 3. Medium Pressure Braking After light bedding, perform 10-15 hard stops from 80 mph to 10 mph using maximum pedal pressure to avoid ABS or locking the tires. Pads should begin to emit some odor and light smoke, indicating proper transfer layer development. 4. Cool-Down Phase Drive for 5 minutes whole minimizing brake use. This allows pads and rotors to cool gradually and evenly, preventing thermal shock and ensuring proper pad bonding. 5. Post-Bedding Rest Let the rest for 24-48 hours if possible. This helps fully cure the pad resins and stabilize the pad compound structure for maximum performance. Important Bedding Tips: Do not come to a complete stop while pads are hot.  Avoid heavy braking with new pads before completing the bedding process.  Always bed in pads and rotors as a matched set (used pads on new rotors or vice versa can cause poor performance).  Proper bedding improves brake modulation, reduces judder, and maximizes the lifespan of your Ferodo racing pads. Whether you run Ferodo DS2500 on the street or DS1.11 or DS3.12 on the track, take time to bed them in right—your braking performance depends on it. Important Note Ferodo Racing Brake Pads are for off-road use only. These products contain copper and are not legal for road use in some regions. It is the buyer’s responsibility to determine legal compliance based on their location.