Brand

Schuberth SP1 Cheek Pads  Replacing your SCHUBERTH SP1 Cheek Pads is the perfect way to improve the fit of your helmet! The removable Cheek Pads come in a variety of thicknesses, which can dramatically change the way your helmet feels.       

Schuberth SP1 Helmet Speaker Kits Integrated speaker kits from Schuberth elevate your communication experience to the next level by seamlessly incorporating high end audio components into your Schuberth SP1 helmet without compromising comfort or style. Schuberth helmet speaker kits feature speakers built directly into Schuberth Noise Reduction Earcups and a boom-style noise canceling microphone. Dual Electronic Kits also include an earbud connector for use alongside the earcup speakers. If you purchase a Schuberth SP1 helmet with Speaker Kit, the electronics will be pre-installed, with earcup speakers replacing the standard Noise Reduction Earcups. Available Schuberth SP1 Integrated Speaker Kits: SH HK1111: Noise Reduction Earcups with speakers, flex-boom mic, and IMSA connection SH HK1121: 3.5mm earbud jack, flex-boom mic, and IMSA connection SH HK1151 DUAL KIT: Noise Reduction Earcups with speakers, integrated 1/8" (3.5mm) earbud jack, flex-boom mic, and IMSA connection

Schuberth SP1 Individual Top Vent Scoops Individual vent scoops direct cooler air into the Schuberth SP1 Carbon helmet's top vents. Can be purchased individually or in packs of three or six.      

Schuberth SP1 Rear Spoiler The rear helmet spoiler is designed for drivers racing open cockpit vehicles. Attached using double sided adhesive tape, the rear spoiler increases stability by providing slight downforce.       

Schuberth SP1 Top Air  Add Top Air Ventilation to Your Schuberth SP1 Schuberth's flat, low-headroom top air attachment lets you connect your Schuberth SP1 helmet to your forced-air ventilation system. The Schuberth SP1 Top Air attaches to the top of the SP1 using high strength double-sided adhesive, and allows drivers to pump fresh air through the dedicated air channels within the helmet EPS. Add cooling fresh air to your Schuberth SP1 Carbon helmet without compromising roof clearance. Choose from large- or small-inlet connector.

Schuberth SP1 Top Vent Scoop Clear top vent scoop directs cooler outside air into the Schuberth SP1 Carbon's top vents. Choose Standard or Flat style.

Schuberth SP1 Visor 3MM THICK VISOR 3D INJECTED Schuberth 3mm visor derived directly from their F1 expertise. Twelve different visor shades are available from transparent to dark with several mirrored and multi-layer coating options. All standard visors are compatible with the Pinlock 120 fog resistant lens, and clear tear-off buttons are installed. Each visor comes with a soft visor pouch to protect visors when not in use. SCHUBERTH SP1 VISOR AVAILABLE COLORS: Light Smoked Blue Dark Smoked Blue Light Smoked Red Dark Smoked Red Light Tint Dark Tint Light Mirrored Silver Dark Mirrored Silver Clear Clear  

Competition Motorsport Racing Seat Mounting Hardware Kit Complete Mounting Kit Includes: Four (4) 8x1.25 25mm Bolts Four (4) 8x1.25 20mm Bolts Four (4) 8x1.25 Locking Nuts Eight (8) Washers (Sparco Part Numbers 50001 and 50002, everything you need in one place.)

Shock Doctor Eject Helmet Removal System Helps reduce the risk of post-crash neck and spine injuries! The Shock Doctor Eject emergency helmet removal system consists of a small inflatable bag worn inside the helmet. In the event of an incident, safety workers or EMTs inflate the bag, which safely pulls your helmet off without placing any strain on the neck. The bag weighs about one ounce and will not affect the fit of your helmet. Required by AMA, IRL, and IMSA.

Simpson Hybrid S 3-Point Head and Neck Restraint The Hybrid S Head Restraint is FIA and SFI approved (when worn with a multi-point harness system) and is tested and shown to be compatible with 3-point harnesses used by Car Club enthusiasts and High Performance Driving Experiences. This allows Driving Instructors, Auto Manufacturing Test Engineers, and others in cars with 3-point harnesses to have added protection. We are pleased to offer this great option for increased protection to this sector of the market. Bear in mind, however, that on a racetrack the best protection we believe is a Full-Containment Cockpit System that includes a full containment seat, Snell SA2015 or FIA 8860 rated helmet, FIA or SFI approved head restraint, and 6- or 7-point racing harness system. SIMPSON HYBRID S 3-P0INT HNR  OPTIONS: Select your size based on the size chart Competition Motorsport only carries this device with standard HANS post anchor clips as they're lightweight and easy to attach/detach SIMPSON HYBRID S 3-P0INT HNR FEATURES: FIA and SFI Approved with 5-, 6- and 7-point harness systems FMVSS Tested for use with 3-point OEM belt system High quality carbon fiber construction Low profile, no high back to hook on the roll bars, etc. in emergency exit Multiple load paths to dissipate head loads Buckle attachment in front, no bulky straps underneath SIMPSON HYBRID S 3-P0INT HNR  INSTALLATION: To use a Hybrid S with a 3-point seat belt system, the SAS (Seatbelt Anchoring System) is not used. (The SAS strap anchor loops hook into the buckle of a 5-, 6- or 7-point racing harness.) Have the wearer put on the Hybrid S and get into the driver's seat. Follow the instructions on fitting the device to the wearer. Engage the 3-point seat belt and sit in the normal driving position. Have a helper apply gentle pressure to the top of the device, keeping the device stable during tether adjustment. The device should be in a comfortable position behind the driver’s back, against the seat cushion. With the helper holding the device and the driver looking straight forward, hold the triangulated tether up to the anchors on the driver’s helmet. Adjust the side tethers so that the end fitting can be easily inserted into the helmet anchor without pulling down on the helmet. A comfortable adjustment on the side tether is to have about ¼” of slack in the tethers. With the helper still holding the device down and the driver looking straight ahead, adjust the rear tethers so that there is ½” to 1” of slack. Test the amount of head movement by moving the head straight forward. The driver should have 1” to 2” of forward head movement before the slack is taken out of the tether. Remember when checking this not to rotate the head down; translate it straight forward. This should allow for plenty of head movement on track. AIRBAG USE WITH HYBRID S: DO NOT unhook or disable the airbag system installed by the auto manufacturer or their authorized installer. Outside experts in Detroit have confirmed this and require their test engineers to use the Hybrid S in conjunction with the airbag in a 3-point system. Simpson agrees that the airbag and Hybrid S work together to increase protection in frontal crashes.

  Simpson Hybrid S 3-Point Head and Neck Restraint(with M61 Anchor)  The Hybrid S Head Restraint is FIA and SFI approved (when worn with a multi-point harness system) and is tested and shown to be compatible with 3-point harnesses used by Car Club enthusiasts and High Performance Driving Experiences. This allows Driving Instructors, Auto Manufacturing Test Engineers, and others in cars with 3-point harnesses to have added protection. We are pleased to offer this great option for increased protection to this sector of the market. Bear in mind, however, that on a racetrack the best protection we believe is a Full-Containment Cockpit System that includes a full containment seat, Snell SA2015 or FIA 8860 rated helmet, FIA or SFI approved head restraint, and 6- or 7-point racing harness system. SIMPSON HYBRID-S HNR OPTIONS: Select your size based on the size chart M 61 Anchors SIMPSON HYBRID-S HNR FEATURES: FIA and SFI Approved with 5-, 6- and 7-point harness systems FMVSS Tested for use with 3-point OEM belt system High quality carbon fiber construction Low profile, no high back to hook on the roll bars, etc. in emergency exit Multiple load paths to dissipate head loads Buckle attachment in front, no bulky straps underneath SIMPSON HYBRID-S HNR INSTALLATION: To use a Hybrid S with a 3-point seat belt system, the SAS (Seatbelt Anchoring System) is not used. (The SAS strap anchor loops hook into the buckle of a 5-, 6- or 7-point racing harness.) Have the wearer put on the Hybrid S and get into the driver's seat. Follow the instructions on fitting the device to the wearer. Engage the 3-point seat belt and sit in the normal driving position. Have a helper apply gentle pressure to the top of the device, keeping the device stable during tether adjustment. The device should be in a comfortable position behind the driver’s back, against the seat cushion. With the helper holding the device and the driver looking straight forward, hold the triangulated tether up to the anchors on the driver’s helmet. Adjust the side tethers so that the end fitting can be easily inserted into the helmet anchor without pulling down on the helmet. A comfortable adjustment on the side tether is to have about ¼” of slack in the tethers. With the helper still holding the device down and the driver looking straight ahead, adjust the rear tethers so that there is ½” to 1” of slack. Test the amount of head movement by moving the head straight forward. The driver should have 1” to 2” of forward head movement before the slack is taken out of the tether. Remember when checking this not to rotate the head down; translate it straight forward. This should allow for plenty of head movement on track. AIRBAG USE WITH HYBRID S: DO NOT unhook or disable the airbag system installed by the auto manufacturer or their authorized installer. Outside experts in Detroit have confirmed this and require their test engineers to use the Hybrid S in conjunction with the airbag in a 3-point system. Simpson agrees that the airbag and Hybrid S work together to increase protection in frontal crashes.

Simpson Hybrid Sport Head and Neck Restraint The Hybrid Sport from Simpson features a light-weight design using DuPont® carbon/polymer construction and provides maximum comfort and maneuverability with superior strength. Hybrids come race ready. The trusted low profile design disappears into the seat when worn and allows for easy in and out of the race car, eliminating the danger of becoming caught in other gear. The protection stays with the racer during multiple impacts, flips and rolls.   SIMPSON HYBRID SPORT HNR FEATURES: SFI 38.1 certification. Available with patent pending multi-tether system to enhance side to side movement. DuPont carbon polymer construction. Sleek, modern profile with defined wings for seatbelt containment.   SIMPSON HYBRID SPORT HNR OPTIONS: We can further customize your Hybrid Sport with any of the following:  Select your size based on the size chart. Competition Motorsport only carries this device with standard HANS post anchors (included) as they're lightweight and easy to attach/detach.  

SmartyCam GP HD 2.2 to AiM Dash Connection Cable AiM SmartyCam GP HD 2.2 and SmartyCam HD Version 1 (Black Box Camera) replacement connection cable to connect to your Solo DL, MXS, MXG, MXP, MXL2, AiM Data Logger or SMC Bridge. This is a connection cable that has a 712 5 pin male connector on one end and another 712 5 pin male connector on the other end. SmartyCam GP HD 2.2 to AiM Dash Connection Cable Details: Manufacturer: AiM Manufacturer part number: V02554820 Alternate part number: AIM-MC-267 SmartyCam GP HD 2.2 and HD to AiM Dash or Data Hubs Included with all SmartyCam HD kits Length: 4 Meters (12ft) End 1: 5 Pin Male 712 Thread-On Connector End 2: 5 Pin Male 712 Thread-On Connector These CAN cables have male 5-pin 712 (screw-in) connectors at each end to connect the AiM SmartyCam GP HD 2.2, SmartyCam HD (version 1 black box looking camera) to your Solo DL. This cable also is used to connect your AiM SmartyCam HD (version 1) to your AiM logger or SMC Bridge. Note: Not compatible with the original SmartyCam (gray unit with the viewing screen on top) or the later SmartyCam HD "Rev 2". The version 1 can be identified by a 7/8" diameter lens with either a 67 or 87 degree field of view, and a viewfinder flush with the front of the housing. Later SmartyCam HD Rev 2 had a larger 1 3/8" OD lens marked as 60 or 120 degree field of view and a cover over the front viewfinder held on by 8 screws. The original SmartyCam and SmartyCam HD Rev 2 require a CAN cable with a 7-pin connector. Although the connectors are correct, this cable can NOT be used to connect the SmartyCam HD GP bullet camera to the base recording unit, the internal wiring is different. How do I make sure I have an original SmartyCam H.D. Rev 1? First, your SmartyCam does not have any type of microphone. Second there is a 5 pin connection (for this control cable) and a 4 pin connection for GPS antenna. If you have a 4 pin and 7 pin, the you have a new Rev 2.

Sparco 2 Inch Alcantara Harness Pads Special memory foam harness shoulder pads covered in Alcantara suede with embroidered Sparco logo. FEATURES: Memory foam for amazing comfort. Alcantara stays in place, wears well. For use with 2-inch racing harnesses. Includes two harness pads per package. 

Sparco 4 Point Racing Harness (3" Shoulder Straps) Strap In and Level Up Your Ride with the Sparco 4 Point Racing Harness The Sparco 4 Point Racing Harness is here to redefine your driving experience, turning every ride into a secure, race-ready adventure. And no, we're not just pulling your leg...or should we say, your lap belt? Why the Sparco Harness is the Co-Pilot You Didn't Know You Needed Unity In Safety: Designed to work in perfect harmony with Sparco's competition seats, this harness doesn't just keep you in place; it becomes one with your racing setup. It's like finding the peanut butter to your jelly. Quality Speaks Volumes: Crafted from top-notch fabric and boasting durable fasteners, this harness ensures that once you're strapped in, you're in for a secure and comfy ride. No more wiggling around trying to find that sweet spot! A Perfect Fit: With 2-inch lap and 3-inch shoulder straps, this 4-point masterpiece offers a snug embrace. And thanks to the aircraft-quality quick-release buckle with integrated anti-submarine belts, getting in and out is a breeze—no advanced engineering degree required. Smooth Operator: The lightweight steel adjusters are like butter, making tensioning smooth and clamping just perfect. Because who has time for complicated adjustments when the track is calling? Snap To It: Each belt comes with snap-on fixings, making installation a snap (pun intended). And since they're FIA approved, you can hit the track with confidence, knowing you're as safe as can be. Sparco 4 Point Harness Tech Specs Lap of luxury: 2" lap belts for that just-right fit. Shoulder the load: 3" shoulder straps to keep you snug without the hug-too-tight feel. Pull for power: Pull-up lap belts for on-the-fly adjustments. Smooth moves: Lightweight steel adjusters for that seamless tensioning. Snap happy: Snap-in Kit Mounting included because who doesn't love convenience? Seal of approval: FIA approved, because your safety is non-negotiable. Imagine hitting those corners with the confidence of a pro, strapped in securely and focused on the finish line, not on your seatbelt. That's what the Sparco 4 Point Racing Harness brings to the table — or should we say, to the driver's seat. Sparco’s full line of harnesses works in unity with most competition seats. Crafted from high-quality fabric and fitted with durable fasteners, each harness restrains the body for added safety and protection. The 4-point harness features 2-inch lap and 3-inch shoulder straps that attach in the center using an aircraft-quality quick-release buckle with integrated anti-submarine belts. The lightweight steel adjusters allow for smooth, quick adjustments and perfect clamping. Each belt attaches to your car's frame using snap-on fixings. Available in pull-up only. Sparco 4 Point Racing Harness Details Manufacturer: Sparco Manufacturer part no.: 04716M1 2" lap and 3" shoulder straps Pull-up lap belts Light-weight steel adjuster for smooth and quick tensioning Snap-in mounting kit included FIA approved

Sparco Six-Point Enduro Racing Harness 2" HANS SHOULDER BELTS W/ STEEL ADJUSTERS Want a Sparco harness to match your new Sparco seat?  This is the one to buy.  Sparco’s full line of harnesses works in unity with Sparco's competition seats. Crafted from high-quality fabric and fitted with durable fasteners, each harness restrains the body for added safety and protection. This six-point HANS-compatible harness features two-inch lap belts, with two-inch shoulder straps Each strap attaches in the center using aircraft-quality quick-release buckles, with integrated anti-submarine belts. The steel adjusters allow for smooth, quick adjustments and perfect clamping. Shoulder and sub belts attach to your car or seat mounts using snap-on fittings, with carabiner fasteners for lap belts. This harness is FIA approved. TECHNOLOGY 2" Lap and Shoulder belts Light-weight carabiner fasteners for lap belts Pull-down lap belts Light-weight steel adjuster for smooth and quick tensioning Snap-in mounting kit included FIA Approved Available in black, blue, or red.