FluidLogic
FluidLogic 360 Helmet Side Kit
$209.00
FluidLogic 360 Helmet Side Kit
Everything needed to completely set up any helmet to connect with the FluidLogic Flush 360 System
Includes:
Helmet Side Flush 360
Aquacom Pro (smaller mic size)
Aquacom Baja (larger mic size)
4mm tubing
Chillout Systems
Chillout Systems Insulated Coolant Hose
from $195.00
Chillout Systems Insulated Coolant Hose
The Chillout Hose is insulated liquid-transfer tubes encased in an ultra-durable, tear-resistant fabric shield.
Six to ten feet of hose that connects your cooling garment to the driver cooling unit with ¼” fittings for a consistent flow cycle.
Hose too long for your set-up? Solution: cut hose to desired length. Our hoses comes with an extra supply of matching shrink wrap for a flawless, durable, clean look.
FEATURES:
The 10-Foot hose includes additional heat shrink tubing for custom sizing while maintaining a finished look.
Male connectors, two pieces.
Female dual-prong connector to connect cooler, one piece
Can be connected to other hoses to extend length (including Y connector).
Double-Layer Insulation: one layer to protect the hose, a second to keep your coolant cool and efficient.
Stilo
Stilo ST5 Helmet Top Air Systems
$195.00
Keep Your Stilo ST5 Helmet Ventilated With The Stilo Top Air Kit
Fresh air keeps you cool and keeps sweat from getting in your eyes as you take the checkered flag. Endurance racers keep their focus high and lap times low by staying in the cool zone.
This unique cooling system feeds air from your car’s fresh air system to both the top of your head and to the front of your face, while at the same time helping keep the inside of your visor clear. This system integrates into the existing design of the ST5 helmet and does not require any drilling of the shell or modifications to the internal EPS foam.
There are four small ventilation holes molded into the top of every ST5 helmet. Stilo's Top Air system fits over the forward two holes and extends down the front of the helmet and just under the top of the visor. Air fed into the Top Air is directed both to the top of the head and down over the face. A small deflector just inside the visor area directs air towards the visor and away from the eyes. Old air flows out of the rear holes on the top of the helmet and from the bottom of the helmet, significantly reducing CO2 buildup in the helmet.
Stilo's Top Air System can be fitted to all Stilo ST5 model helmets. It comes in two sizes to best fit your helmet:
YA0834 Non-Adjustable for helmets XS 54cm to L 59cm
YA0857 Non-Adjustable for helmets L+ 60cm to 4XL 64cm
FluidLogic
FluidLogic Containment Bottle
from $181.00
FluidLogic Containment Bottle (Bottle and Mount Only)
The new WAVE of hydration is here!
The Fluidlogic WAVE is a complete hydration system that keeps your drink of choice cold and secure for your entire ride.
Features & Benefits
Kitchen grade stainless steel is roost and rust resistant.
Quick release bottle mount secures to any roll bar for convenient filling.
Available in 32oz and 64oz capacity for short and long rides
Keeps your drink cold for up to 8 hours
Stay hydrated outside your vehicle when parked at your favorite spot
Wide mouth bottle opening makes it easy to add ice to keep your drink cold all day
Includes:
32oz or 64oz stainless steel bottle
Roll bar quick release mount & hardware
FluidLogic
Maglock Air Kit
$167.00
Maglock Air Kit
**Maglock Air hose NOT included**
Connection Perfection for forced air helmets.
Universal helmet & air hose fitment from the high G's at Indianapolis to the weekend on/offroad racer, MagLock® holds strong.
No more duct tape or zip ties, MagLock® technology creates an air-tight seal with 20lbs of force that will only let go when you need it to.
Lightweight nylon-infused ABS construction stands up to the rigors of motorsports and recreation.
Designed in California, food safe, fire resistant, and features patented technology.
Coolshirt
Coolshirt Cool-A-Clava
$160.00
Coolshirt Cool-A-Clava
The Coolshirt Cool-A-Clava literally helps you keep a cool head under pressure! This helmet insert is superior to any current air- or water-based head cooling unit on the market. The Coolshirt Cool-A-Clava plugs in to any current Coolshirt cooler or bag system. The Cool-A-Clava requires no special hardware and can be used with nearly every helmet available!
Last but not least, the Coolshirt Cool-A-Clava eliminates the need to install a separate helmet blower system. That's less drain on your electrical system, fewer hoses, less weight and lower chance of an equipment failure. This is, without a doubt, a must-have to stay cool and focused while on track.
Coolshirt
Coolshirt Water Hose
from $132.00
Coolshirt Water Supply Hose
The Coolshirt water supply hose connects your Coolshirt cooling garment to your cooler system. Choose from 4-, 8-, and 12-foot lengths. All Coolshirt water supply hoses come with emergency safety pull fittings that will release with as little as 21 pounds of force.
Coolshirt
Coolshirt Cooler Mounting Tray
from $127.00
The Coolshirt Cooler Mounting Tray secures hard-shell units like the Club or Pro System coolers to your vehicle. Comes with a strap, choose 13- or 19-quart depending on your cooler size.
Chillout Systems
ChillOut Systems Rapid Release Shirt Handle
$119.00
The Rapid Release dry break system, makes driver changes fast and effortless. No fumbling with tubes or connectors while under pressure. Just a quick press, and coolant/water starts flowing instantly. In an emergency, the connectors release when a force greater than 10 lbs is applied.
FEATURES:
Effortless dry break system
Emergency release feature
INCLUDED:
2 x 1/4" barbed quick-release fittings
1 x driver-side handle
2 x 36" reinforced, non-kinking extensions
2 x 1/4th to 5/16th barrel connectors
2 x 1/4th to 1/4th barrel connectors
2 x 36" reinforced cooling tubes
Chillout Systems
Chillout Systems Wiring Harness
$105.00
Chillout Systems Wiring Harness
This 10 AWG wiring harness features a 10-foot shock-resistant rubber power cord wrapped in a protective textile fabric. Overall length is 14 feet.
Chillout Systems
Chillout Systems 4" 285 CFM Blower
$91.00
Chillout Systems 4-Inch 285 CFM Blower
An ultra-efficient and lightweight design, the Chillout 4-inch 285 CFM blower offers high air output and low amp draw. This is the most powerful and reliable blower in its class.
FEATURES:
285 cubic feet per minute (CFM)
4.7 Amps
12 Volts
Lightweight, durable, and ultra-reliable
Chillout Systems
Chillout Systems 3" Air Duct Plenum
$74.00
Chillout Motorsports 3" Air Duct Plenum connects to your Cooling System, efficiently increasing cooling performance whilst simultaneously reducing amp draw from your electrical system.
The plenum is designed to fit the intake side of your Quantum Cooler, allowing for much cooler air to be forced through the system via the 3" duct. A 200 CFM blower (Minimum) is required in conjunction with the plenum for the best performance.The 3" Air Duct Plenum attaches via the plenum holder found on the front of the Quantum Cooler systems (V2 and above), creating a seal to keep the cooler pressurized with the cool air. Forcing cool air through the system and out through the exhaust side of the cooler is the most efficient way to reach maximum cooling - no wasted cool air, and the cooling shirt system appreciates every bit of cool air it can get.INCLUDED:
3" Air Duct Plenum
Chillout Systems
Chillout Systems 4" Neoprene Air Duct Hose
from $70.00
Our Neoprene Air Duct Hose is extremely flexible, pliable and structurally strong thanks to a coated spring-steel wire support helix that prevents it from collapsing. The fiberglass fabric cover and fiberglass cord are both impregnated and coated with neoprene rubber.With a temperature range between -45° F to 330° F, this makes it ideal for most applications, most importantly bringing fresh/cool air to your Quantum Cooler. Also perfect for cockpit cooling and other low-pressure ducting applications where extreme heat can't be avoided. Under-hood applications such as connecting an air intake to an airbox, or an airbox to a throttle body are also great uses.FEATURES:
4" Interior Diameter
330ºF Heat Resistance
Chillout Systems
Chillout Systems Neoprene Air Duct Hose
from $69.00
Chillout Systems Neoprene Air Duct Hose
Chillout's Neoprene Air Duct Hose is extremely flexible, pliable and structurally strong thanks to a coated spring-steel wire helix that prevents it from collapsing. The fiberglass fabric cover and fiberglass cord are both impregnated and coated with neoprene rubber.
With a temperature tolerance between -45° F and 330° F (7º C and 165º C), the Chillout Neoprene Air Duct Hose is ideal for most racing applications, including channeling fresh, cool air to your Chillout Quantum Cooler. It's also perfect for cockpit cooling and other low-pressure ducting applications where extreme heat can't be avoided. Under-hood applications such as connecting an air intake to an airbox, or an airbox to a throttle body are also great uses.
Choose 6-foot or 12-foot overall length.
Chillout Neoprene Air Duct Hose Features:
4 inch interior diameter
High strength and flexibility
Up to 330º F (165º C) heat resistance
Product SKU: ADH4
Chillout Systems
Chillout Systems Mounting Trays
from $63.00
Select from the options here to get the right mounting tray for your Chillout Systems Quantum Cooler (v3 or Pro).