The best highest performance racing brake fluid on the market today is CMS Performance RF1 with a dry boiling point of 622ºF!
Competition Motorsport CMS Performance RF1 DOT4 Racing Brake Fluid (500 ml) from $24.95
CMS Performance RF1 DOT4 622oF Racing Brake Fluid Buy in bulk and save. Get six bottles and save 15%, or a case of 12 and save a whopping 25%! The Highest Dry Boiling Point Racing Brake Fluid You Can Buy CMS Performance RF1 fully synthetic Racing Brake Fluid is formulated to provide the highest performance under racing and track-day conditions, where braking systems operate at very high sustained temperatures. RF1 exceeds all DOT 3 & 4 requirements and is compatible with all DOT 3, 4, and 5.1 fluids. (Not compatible with DOT5 or mineral-based brake fluids.) There is perhaps no single safety system more important in racing than brakes. And no part of that system is more critical than brake fluid. At Competition Motorsport, we got tired of (and a little nervous) using "racing" brake fluid on the track that didn't live up to its claimed performance. So we did something about it. Manufactured in partnership with Orthene Chemicals, a British brake fluid supplier to professional race teams in Formula 1, WEC, and many other pro series, CMS Performance RF1 Racing Brake Fluid is formulated to maintain consistent viscosity, lubricity, and compressibility at extreme temperatures and line pressures found in racing, track days, and spirited driving. Bottom line: you can spend more money, but you can't buy higher-performing racing brake fluid! CMS Performance RF1 Racing Brake Fluid Specifications: Typical dry boiling point: 622° F (328° C) Typical wet boiling point: 399° F (204° C) Exceeds DOT3 & DOT4 standards Individual 500 ml (16.7 oz.) bottles Click Here For The RF1 Product MSDS Sheet A Note About Brake Fluid Boiling Points DOT 4 brake fluid like RF1 is hygroscopic, meaning it attracts water over time sitting in your brake lines and reservoir. At high brake temperatures, this water can boil in your car's brake lines, causing the fluid in the lines to become compressible. That's what you feel when you experience brake fade. This is why the "wet" (aged fluid) boiling point of any brake fluid is substantially lower than the "dry" (brand new fluid) boiling point. Since time is the enemy of brake fluid performance, the best practice is to replace your racing brake fluid before each track event/weekend. At a minimum, flush it with new fluid at least every three months if you're consistently racing and/or driving at track days. A couple bottles of fluid will flush most sports cars or race cars. It ends up being pretty cheap insurance against learning about brake fade the hard way.
Girodisc Pad Spreader GDPS01
Girodisc Girodisc Pad Spreader GDPS01 $250.00
Girodisc Brake Pad Spreader This indispensable tool is used by race teams, shops, and enthusiasts alike who have high performance four- and six-piston calipers. The spreader is designed to spread brake pads and pistons in four- and six-piston calipers to facilitate quick replacement of pads and/or rotors in a shop or racing environment.No more screwdrivers, pliers, hammers, or C-clamps! This tool will retract the pistons evenly and all the way back into their bores with one squeeze of the levers. The Girodisc spreader was designed around popular four-piston and six-piston calipers from Brembo, AP Racing, Alcon, and other performance calipers in racing and road use. To help fit in any caliper, the amount of throw is adjustable.Insert the spreading plates one way for wider six-piston calipers, then turn the spreader 90o and use the plate sides for four-piston calipers.The Girodisc Pad Spreader is made from heavy-gauge steel and is powder-coated for durability. The slider is cadmium-plated, and nylon pivot bushings ensure smooth action. The Girodisc Pad Spreader will quickly become an invaluable tool for any race team, shop, or enthusiast who changes pads and rotors with any frequency.
Pagid Racing Brake Pads No. 2405
Pagid Pagid Racing Brake Pads No. 2405 from $332.30
    Fits These Vehicles: Make Model Build (Year) Front Rear Porsche 996 3.4 C & 3.6 97 - 05 X   Porsche 996 3.4 C Cup 99 - 01   X Porsche 996 3.4 C Cup 97 - 98   X Porsche 996 3.6 C 4S 03 - 05   X Porsche 996 GT2 02 - 05   X Porsche 996 GT3 02 - 05   X Porsche 996 GT3 99 - 01   X Porsche 996 GT3 Cup 02 - 05   X Porsche 996 GT3 RS [street car] 03 - 05   X Porsche 996 Turbo 99 - 05   X Porsche 997 3.6 C & 3.6 C4 05 - 09 X   Porsche 997 3.8 C S & 3.8 C 4S 05 - 12   X Porsche 997 3.8 Carrera GTS 09 - 11   X Porsche Boxster [987] [ceramic brakes] 05 - 12   X Porsche Boxster S [986] 99 - 05 X   Porsche Boxster S [987] 05 - 12 X   Porsche Cayman [987] 09 - 12 X   Porsche Cayman [987] [ceramic brakes] 06 - 12   X Porsche Cayman R [987] (none ceramic) 10 - X   Porsche Cayman S [981] [ceramic brakes] 13 -   X Porsche Cayman S [987] 06 - 12 X   RSL 29: The PAGID RS29 (Yellow) is the world-leading endurance brake pad used by most of the winning teams in motorsport. Although designed primarily for endurance racing, many competitors use this material successfully for sprint and short distance races also. RS29 has also found favor in the growing track day market due to the level of control, good cold performance, long life and low disc wear. RS 14: The PAGID RS14 (Black) is a high friction value ceramic compound with very good modulation and high fade resistance. A very popular, aggressive pad with strong initial bite and high torque. In addition to the track-day environment, RS14 has shown success in short- to medium-distance circuit racing as well as gravel and tarmac rallying. RS 44: The PAGID RS44 (Orange) is a carbon-based, highly controllable pad with a progressive friction curve. It has a medium initial bite and good low temperature response. A very versatile pad for use on both front and rear axles, or in conjunction with RS14 on the front axle in FWD cars. Particularly popular in Porsche club racing, fitted as OEM on the Porsche 993 RS and GT2.
PFC Brake Pads 0776.XX.17.44 FRONT
Performance Friction PFC Brake Pads 0776.XX.17.44 FRONT $384.95
PFC 11 COMPOUND A new generation sprint and medium distance friction: the ultimate in control with superior disc conditioning. Developed from 01 compound with improved bite, modulation, and release characteristics. It is ultra smooth and developed to reduce wheel locking at the end of braking while giving more cold and hot bite than the endurance oriented 08 compound. Brake with confidence; brake with ultimate control and modulation. PFC 08 COMPOUND One of PFC's most popular compounds which came to fame in Endurance Sportscar and GT racing due to its performance in applications where smooth initial bite is a must. PFC08 has a slight friction rise with temperature, excellent release and modulation characteristics. Despite its considerable performance, 08 has the lowest wear rate of all PFC compounds and can easily match the wear characteristics of the other competitors' materials but with much higher bite and consistent performance across a broad temperature range. FITMENT (Iron Rotors Only) Most Porsche 986, 987, 996, and 997 Front Calipers
PFC Brake Pads 0738.XX.16.44 REAR
Performance Friction PFC Brake Pads 0738.XX.16.44 REAR $373.95
PFC 11 COMPOUND A new generation sprint and medium distance friction: the ultimate in control with superior disc conditioning. Developed from 01 compound with improved bite, modulation, and release characteristics. It is ultra smooth and developed to reduce wheel locking at the end of braking while giving more cold and hot bite than the endurance oriented 08 compound. Brake with confidence; brake with ultimate control and modulation. PFC 08 COMPOUND One of PFC's most popular compounds which came to fame in Endurance Sportscar and GT racing due to its performance in applications where smooth initial bite is a must. PFC08 has a slight friction rise with temperature, excellent release and modulation characteristics. Despite its considerable performance, 08 has the lowest wear rate of all PFC compounds and can easily match the wear characteristics of the other competitors' materials but with much higher bite and consistent performance across a broad temperature range. FITMENT (Iron Rotors Only) Most Porsche 986, 987, 996, & 997 Rear Calipers
D1-032 Girodisc FRONT Replacement Rotor Rings (350mm)
Girodisc D1-032 Girodisc FRONT Replacement Rotor Rings (350mm) $800.00
ROTOR RINGS ONLY (NO HATS) Need new rings for your Girodisc 350mm 2pc rotors? We got them. Rings come complete with all new hardware and full instructions for re-assembly. Price is for a pair of rings and 2 hardware kits. Additional hardware kits are available separately upon request.
A2-032 Girodisc 2pc REAR Brake Rotors (350mm)
Girodisc A2-032 Girodisc 2pc REAR Brake Rotors (350mm) $1,300.00
The Girodisc system is an upgrade to a 350mm two-piece steel rotor and aluminum hat combination, a direct replacement for the OEM brake disc. The two-piece floating disc will bolt directly to the car and work with OEM calipers perfectly. By upgrading your brakes with these lightweight high-performance replacements -- as opposed to a big brake kit -- your factory brake bias is maintained as well as your ABS efficiency. Girodisc rotors are lighter than the OEM rotors, reducing rotational and unsprung weight for quicker acceleration and suspension response. When used with Pagid or PFC performance brake pads and Competition Motorsport RF1 racing brake fluid (also available from CMS), you have an amazing solution to overheating, cracking and warping rotors. The central hat section of the disc is made from 6061-T6 aircraft specification aluminum. The disc is manufactured in the USA from cast iron, made to the same specification and with the same material used by professional racing organizations. The rotor's curved-vane design was developed in racing and acts as a centrifugal pump to force cooling air through the disc. The rotor and hat mount together through a floating mount system which utilizes 8-10 high strength alloy steel drive pins manufactured by GiroDisc in the USA to our own specifications and are cadmium plated for corrosion resistance. The alloy drive pins transfer the load from braking while maintaining the axial and radial float between the disc rotor and hat. The pins are secured by Grade 12 cap screws with hardened washers and mounted with anti-noise spring washers to allow for heat expansion while eliminating the rattle and noise typically associated with floating rotors. The two-piece Girodisc design allows for rotor-ring only replacement to minimize future replacement costs. Priced per pair
Goodridge G-Stop Stainless Brake Lines Porsche 911 (1997-2012)
Goodridge Goodridge G-Stop Stainless Brake Lines Porsche 911 (1997-2012) $183.00
Goodridge G-Stop High Performance Stainless Brake Lines This Kit Is For: Porsche 996 (1997-2004 All) Porsche 997 (2005-12 All, including GT2/GT3/GT3RS) Goodridge G-Stop high performance brake lines for the Porsche 996 & 997 consist of the finest quality PTFE inner hose covered by a braided stainless steel outer casing. This gives you a much firmer, more responsive brake pedal by eliminating the “spongy” feel that often accompanies stock rubber brake lines, making them ideal for the very high brake pressures seen during HPDE track days. G-Stop High Performance Brake lines are abrasion and corrosion resistant so they last a long time under harsh conditions. Goodridge G-Stop high performance brake lines are direct bolt-on replacements for all of the rubber brake lines in your Porsche's brake system. Four brake lines are included in each kit, with hose ends and brake line brackets that match the car’s original equipment.  Conforming to Federal Motor Vehicle Safety Standard Number 106, Goodridge G-Stop high performance brake lines are U.S. DOT certified and T.U.V. approved. All Goodridge G-Stop brake lines go through a nine-point Quality Assurance testing process that includes measuring tensile strength and the ability to sustain line pressures to 3,000 psi. Features: Precise fit for your Porsche Greater braking efficiency Resistance to abrasion and corrosion Firmer pedal under heavy braking Added reliability, safety and brilliant looks Technically superior and race proven DOT, TUV, ADR, DEKRA, ARAICCC, ISO9001 Accredited. FMVSS 106 compliant, DOT approved   Brake components should be installed by a competent mechanic in a professional manner.  Incorrect installation of brake components can cause a major safety problem or an accident.
Pagid Racing Brake Pads No. 2474
Pagid Pagid Racing Brake Pads No. 2474 from $371.26
  Fits These Vehicles: Make Model Build (Year) Front Rear Porsche 996 3.4 C Cup 99 - 01 X   Porsche 996 3.6 C 4S 03 - 05 X   Porsche 996 GT3 99 - 01 X   Porsche 996 Turbo 99 - 05 X   Porsche 997 3.8 C S & 3.8 C 4S 05 - 12 X   Porsche 997 3.8 Carrera GTS 09 - 11 X     RSL 29: The PAGID RS29 (Yellow) is the world-leading endurance brake pad used by most of the winning teams in motorsport. Although designed primarily for endurance racing, many competitors use this material successfully for sprint and short distance races also. RS29 has also found favor in the growing track day market due to the level of control, good cold performance, long life and low disc wear. RS 14: The PAGID RS14 (Black) is a high friction value ceramic compound with very good modulation and high fade resistance. A very popular, aggressive pad with strong initial bite and high torque. In addition to the track-day environment, RS14 has shown success in short- to medium-distance circuit racing as well as gravel and tarmac rallying.
A1-032 Girodisc 2pc Front Brake Rotors (350mm)
Girodisc A1-032 Girodisc 2pc Front Brake Rotors (350mm) $1,300.00
Competition Motorsport is an authorized dealer for Girodisc products. As one of the largest stocking dealers in the country, we ship most products the same or next business day to ensure we meet your delivery deadline.This Girodisc system upgrades the OEM brakes to a two-piece steel disc and aluminum hat. This two-piece "floating rotor" design will bolt directly to your car and work flawlessly with the OEM calipers.Upgrading your brakes to lightweight, high-performance Girodisc rotors, you maintain the factory brake bias and ABS effectiveness. Much lighter than the OEM rotors, Girodisc rotors reduce rotational and unsprung mass giving you stronger braking and faster suspension response.Combined with Pagid or PFC performance brake pads and Competition Motorsport RF-1 racing brake fluid, Girodisc rotors are the ultimate solution to overheated, cracked, warped rotors that result from high-performance driving.The central hat of the rotor is made from 6061-T6 aircraft aluminum. The disc is manufactured in the USA from the same cast iron used by professional racing organizations. Its curved-vane design, developed in racing, acts like a centrifugal pump forcing cool air through the disc.The disc and hat mount together through a floating mount system using ten cadmium plated, high-strength alloy steel drive pins manufactured by Girodisc. These drive pins transfer braking load while maintaining axial and radial float between the disc and hat to allow for heat expansion. Anti-noise spring washers eliminate the noise typically associated with floating rotors.This two-piece Girodisc design allows for disc-only replacement, reusing the hat to minimize maintenance costs.Sold/priced per pair.
D2-032 Girodisc REAR Replacement Rotor Rings (350mm)
Girodisc D2-032 Girodisc REAR Replacement Rotor Rings (350mm) $850.00
ROTOR RINGS ONLY (NO HATS) Need new rings for your Girodisc A2-032 rear rotors? We got them. Rings come complete with all new hardware and full instructions for re-assembly. Price is for a pair of rings and 2 hardware kits. Additional hardware kits are available separately upon request.