
CMS Performance
CMS Performance RF1 Racing Brake Fluid (500 ml)
from $21.95
CMS Performance RF1 DOT4 Racing Brake Fluid
Real Life 622º Boiling Point Without the Real High Price
RF1 Racing Brake Fluid from CMS Performance is a fully-synthetic DOT4 brake fluid formulated to provide extraordinary performance under the most demanding high-temperature racing and track-day conditions. With a dry boiling point of 622º F / 328º C, RF1 exceeds all DOT 3 & DOT 4 requirements and is compatible with all DOT 3, DOT 4, and DOT 5.1 fluids.
Note: RF1, like all DOT 4 brake fluids, is not compatible with DOT 5 silicone-based or any mineral-based brake fluids.
On the race track, there is perhaps no single safety system more important than your brakes. No single part of that system is more critical than brake fluid, given the extraordinarily high temperatures it operates under. At CMS Performance, we got tired of (and a little nervous) using "racing" brake fluid at the race track that didn't live up to its claimed performance when things got hot. We found more than a few brands whose product was all hype and not high performance.
No Hype. All Performance. No Kidding.
So we did something about it. CMS Performance RF1 is manufactured in partnership with Orthene, maker of the also-excellent Halo P1 racing brake fluid and a brake fluid supplier to many racing teams in Formula 1, WEC, and other professional series. RF1 was formulated to maintain consistent viscosity, lubricity, and compressibility at the extreme system temperatures and line pressures found in racing and track days.
The bottom line is this: you can spend a lot more on brake fluid, but it's hard to find higher-performance than RF1 Racing Brake Fluid.
CMS Performance RF1 Racing Brake Fluid Details:
Manufacturer: CMS Performance
Manufacturer part no.: CMSRF1
Typical dry boiling point: 622º F / 328º C
Typical wet boiling point: 399º F / 204º C
Exceeds DOT 3 & DOT 4 standards
Bottle size: 500 ml (16.9 fl. oz.)
Click Here for Product MSDS Sheet
A Word About Flushing Brake Fluid
All brake fluid degrades over time (not mileage), attracting water as it ages, which, at high brake temperatures, can lead to fluid boil and brake fade or failure. That's why the "wet" (aged) boiling point of any brake fluid is substantially lower than the "dry" (new) boiling point.
To maintain maximum braking performance, Competition Motorsport strongly suggests replacing your brake fluid before every track event, but at least every three months if you're consistently racing and/or driving at track days. It's cheap insurance against learning about brake fade the hard way!

Girodisc
Girodisc Brake Pad Spreader GDPS01
$260.00
Girodisc Brake Pad Spreader
This indispensable tool is used by race teams, shops, and enthusiasts alike who have high performance four- and six-piston calipers. The Girodisc Brake Pad Spreader is designed to easily spread brake pads and pistons to facilitate quick replacement of pads and/or rotors in a shop or racing environment.
No more screwdrivers, pliers, hammers, or C-clamps! This tool will retract the pistons fully and evenly into their bores with one squeeze of the levers.
The Girodisc Brake Pad Spreader was designed to be used with popular racing brake calipers from Brembo, AP Racing, Alcon, and other performance calipers in racing and road use. To help it fit into any caliper, the amount of throw is adjustable.
Insert the spreading plates one way for wider six-piston calipers, then turn the spreader 90o and use the plate sides for four-piston calipers.
The Girodisc Brake Pad Spreader is made from heavy-gauge steel, powder-coated for durability. The slider is cadmium-plated, and nylon pivot bushings ensure smooth action.
The Girodisc Brake Pad Spreader will quickly become an invaluable tool for any race team, shop, or enthusiast who changes pads and rotors frequently.

Pagid
Pagid Racing Brake Pads No. 4925 (Rear)
from $483.90
Pagid Racing Brake Pads No. 4925
Fits The Following Cars:
Porsche 918 Spyder (2013+), Rear
Porsche 991 GT3 (2013+), Rear
Porsche 991 GT3RS (2015+), Rear
Porsche 991 Turbo (2013+), Rear
Porsche Cayman GT4 (2016+), Rear
Porsche Cayman GT4RS (2021+), Rear
Pagid RSL 29:
RSL 29 (known through the racing world as "Pagid Yellow") is the world-leading endurance brake pad used by most of the winning teams in motorsport.
Although designed primarily for endurance racing, many competitors use this material successfully for sprint and short distance races also. Pagid RSL 29 has also found favor in the growing track day market due to the level of control, good cold performance, long life and low disc wear.
Pagid RSC 1:
RSC 1 is a good street/track compromise for enthusiasts with Carbon-Ceramic Brakes. Used for sprint racing and track days with all known types of ceramic brake discs.
RSC 1 is an ideal combination of cold friction, fade resistance, and low thermal oxidation of the disc surface. The compound is a low metallic resin bonded material containing steel and aramid fibers. This material features good all-round characteristics and is suitable for all types of usage.
Pagid RSL 1:
Used in GT cars, Touring cars and prototype endurance racing. Due to the high friction and good modulation, often used in sprint races as well. Low-metallic resin bonded materials containing steel and aramid fibers with very high heat resistance.
RSL 1 maintains a constant friction level over a wide range of temperatures. Its reduced wear rate and disc friendliness make RSL 1 appropriate for endurance races.
Pagid RST 3:
RST 3 is a medium-high friction metal-ceramic compound containing steel fibers. It is known for its combination of bite, friction and controllability.
RST 3 sees a wide range of applications: rally tarmac and gravel, GT cars, Touring cars and prototype circuit racing, formula cars and club racing.

Pagid
Pagid Racing Brake Pads No. 4927 (Front)
$710.13
Pagid Racing Brake Pads No. 4927
Fits These Vehicles:
Porsche 992 GT3 (2022+), Front w/ PCCB
Porsche 992 GT3RS (2023+), Front w/ PCCB
Porsche 918 Spyder (2013+), Front w/ PCCB
Porsche 991 GT3, Front w/ PCCB
Porsche 991 GT3RS, Front w/ PCCB
Porsche 991 Turbo, Front w/ PCCB
Porsche 981/718 GT4, Front w/ PCCB
Porsche 718 GT4RS, Front w/ PCCB
Pagid 4927 RSC 1
The Pagid RSC1 is a good street/track compromise for enthusiasts with Carbon-Ceramic Brakes. Used for sprint racing and track days compound with all known types of ceramic brake discs.
An ideal combination of cold friction, fade resistance and low thermal oxidation of the disc surface.

Performance Friction
Performance Friction PFC Brake Pads 1773.xx.17.44 (Front)
$594.05
PFC Brake Pads 1773.xx.17.44
This is an updated PFC part number. The previous part number was 7721.xx.17.44.
FITMENT (Iron Rotors Only):
Porsche 991 GT3/GT3RS (2014-19), Front
Porsche 991 Turbo/Turbo S (2013-19), Front
Porsche 991.2 3.0 Carrera GTS (2017-19), Front
Porsche 991.2 3.0 Carrera S (2015-19), Front
Porsche 992 3.0 Carrera S & 4S (2020+), Front
Porsche 992 GT3 (2022+), Front
Porsche 992 Speedster (2019-22), Front
Porsche 981 Cayman GT4 (2015-19), Front
Porsche 718 Cayman GT4 (2020+), Front
PFC Brakes offers a wide range of sports car applications. Each PFC product is meticulously created to the highest performance and technology expectations. The folks at PFC take pride in the accomplishments of the drivers and race teams that run PFC products. With More Championships than Any Other™, PFC are among the best racing brakes on the market. Known around the globe in the sports car market, PFC is involved with numerous sports car events including:
IMSA Continental Tire Sports Car Challenge
Porsche Cup Racing
Pirelli World Challenge
With over 35 years of friction knowledge and on-track experience, PFC's process enables them to provide you with the proper friction every time.
NO COMPROMISES
All PFC pad compounds have been thoroughly processed and are “race ready”. That means very easy burnishing to bed pads and rotors.
PFC 331 Compound
PFC 331 is the next generation of PFC endurance material, giving you improved control with ABS while being gentle on rotors. The 331 Carbon Metallic compound has been developed with higher initial bite than PFC’s renowned 08 endurance compound. The 331 has improved release while continuing to offer exceptional control and feel. It boasts a low wear rate and exceptional disc conditioning.
PFC 13 Compound
The PFC 13 is the new generation of ultimate high bite/high friction performance. Performance Friction's 13 compound has been developed with increased bite, excellent modulation, and superior disc conditioning and release characteristics for exceptional control.
Ultra-smooth and great for tracks with high grip or high downforce cars. It is the ultimate combination of high bite and infinite control. Ideal where high bite in the first one-third of the stop is desired. PFC 13 exhibits wear on a par with PFC’s legendary 01 compound, but will operate at higher temperatures if called on.
PFC 13 has a very high threshold for fade resistance. Out of all the high bite/high torque pads on the market, PFC 13 has been shown to have some of the lowest taper wear in a properly designed race caliper.
PFC 11 Compound
A new generation sprint and medium-distance friction compound, PFC 11 gives you the ultimate in control alongside superior disc conditioning. Developed from the famed PFC 01 compound with improved bite, modulation, and release characteristics. The PFC 11 is ultra-smooth, developed to reduce wheel lock-up at the end of braking while giving you more cold- and hot-bite than the more endurance-oriented PFC 08 compound.

Girodisc
A1-146 Girodisc 2pc Front Brake Rotors
$1,750.00
A1-146 Girodisc Two-Piece Front Brake Rotors
FITMENT: Porsche 991 GT3/GT3RS/GT2RS, Front (2014+) with steel brakes
The Girodisc system is a direct replacement for the OEM front rotors on the Porsche 991 GT3, GT3RS, and GT2RS with OEM iron rotors. No modifications are necessary, including full use of factory unmodified pads unlike most aftermarket solutions for this application. The GIrodisc rotors will bolt directly to your car and work with OEM calipers perfectly.
By upgrading your brakes with lightweight, high performance replacements -- as opposed to a big brake kit -- your factory brake bias and ABS efficiency are preserved.
The central hat section of the disc is made from 6061-T6 aircraft specification aluminum. The disc is manufactured from cast iron constructed in the USA, made to the same specification with the same material used by professional racing organizations. The rotors' curved vane design was developed in racing and acts as a centrifugal pump to force cooling air through the disc.
The rotor and hat mount together through a floating mount system which utilizes ten high strength alloy steel drive pins manufactured by Girodisc in the USA to their own specifications and are cadmium plated for corrosion resistance. The alloy drive pins transfer the load from the brake action while maintaining the axial and radial float between the disc rotor and hat. The pins are secured by Grade-12 cap screws with hardened washers and mounted with anti-noise spring washers to allow for heat expansion while eliminating the rattle and noise associated with floating rotors.
The two-piece Girodisc design allows for disc-only replacement as well, minimizing future replacement costs and delivering outstanding performance.
Sold/priced per pair.

Performance Friction
Performance Friction PFC Brake Pads 7727.xx.18.44 (Rear)
$529.00
PFC Brake Pads 7727.xx.18.44
PFC Brakes offers a wide range of sports car applications. Each PFC product is meticulously created to the highest performance and technology expectations. The folks at PFC take pride in the accomplishments of the drivers and race teams that run PFC products. With More Championships than Any Other™, PFC are among the best racing brakes on the market. Known around the globe in the sports car market, PFC is involved with numerous sports car events including:
IMSA Continental Tire Sports Car Challenge
Porsche Cup Racing
Pirelli World Challenge
With over 35 years of friction knowledge and on-track experience, PFC's process enables them to provide you with the proper friction every time.
NO COMPROMISES
All PFC pad compounds have been thoroughly processed and are “race ready”. That means very easy burnishing to bed pads and rotors.
PFC 332 Compound
PFC 332 has been formulated with lower bite and torque for rear brake applications. With a smooth release, the PFC 332 compound offers excellent stability and control. PFC 332 has been designed to work with ABS applications and has exceptionally low wear rates.
PFC 11 Compound
A new generation sprint and medium-distance friction compound, PFC 11 gives you the ultimate in control alongside superior disc conditioning. Developed from the famed PFC 01 compound with improved bite, modulation, and release characteristics. The PFC 11 is ultra-smooth, developed to reduce wheel lock-up at the end of braking while giving you more cold- and hot-bite than the more endurance-oriented PFC 08 compound.
FITMENT (Iron Rotors Only):
Porsche
991 GT3RS
2016-2019
Rear
Porsche
991 GT3
2014-2019
Rear
Porsche
991 Speedster
2019-2021
Rear
Porsche
991 Turbo/Turbo S
2013-2019
Rear
Porsche
992 GT3/GT3RS
2022-
Rear
Porsche
992 Turbo
2019-
Rear
Porsche
918 Spyder
2013-2016
Rear
Porsche
981 Cayman GT4
2015-2019
Rear
Porsche
718 Cayman GT4/GT4RS
2019-
Rear

Girodisc
A2-146 Girodisc 2pc Rear Brake Rotors
$1,750.00
A2-146 Girodisc Two-Piece Rear Brake Rotors
FITMENT: Porsche 991 GT3 / GT3RS / GT2RS, Rear w/ Cast Iron Brakes
This Girodisc system is a direct replacement for the OEM Porsche cast iron rotors on the 991 GT3, GT3RS, and GT2RS. No modifications are necessary, allows use of factory unmodified pads (unlike most aftermarket solutions for this application). The Girodisc rotors will bolt directly to the car and work with OEM calipers perfectly. By upgrading your brakes with lightweight high performance replacements as opposed to a big brake kit, your factory-tuned brake bias is maintained as well as your ABS efficiency.
Girodisc two-piece floating rotors are lighter than OEM brake rotors. This reduction in rotational mass and unsprung weight allows for quicker acceleration, sharper steering, and faster suspension response.
When used with Pagid or PFC performance brake pads and CMS RF-1 brake fluid (available from Competition Motorsport), you have an amazing solution to overheating, cracking and warping rotors.
The central hat section of each Girodisc is made from 6061-T6 aircraft specification aluminum. The disc is manufactured from cast iron constructed in the USA, made to the same specification with the same material used by professional racing organizations. The rotors' curved vane design was developed in racing and acts as a centrifugal pump to force cooling air through the disc.
The rotor and hat mount together through a floating mount system which utilizes ten high strength alloy steel drive pins manufactured by Girodisc in the USA to their own specifications and are cadmium plated for corrosion resistance. The alloy drive pins transfer the load from the brake action while maintaining the axial and radial float between the disc rotor and hat. The pins are secured by class 12.9 cap screws with hardened washers and mounted with anti-noise spring washers to allow for heat expansion while eliminating the rattle and noise associated with floating rotors.
The two-piece Girodisc design allows for disc-only replacement as well, minimizing future replacement costs and delivering outstanding performance.
Sold/priced per pair.

Girodisc
A1-154 Girodisc 2pc Front Brake Rotors for Porsche GT3/GT2/GT4 RS PCCB
$1,950.00
A1-154 Girodisc Two-Piece 410mm Front Brake Rotors
FITMENT:
Porsche GT3 (991) w/ factory PCCB
Porsche GT3RS (991) w/ factory PCCB
Porsche GT2RS (991) w/ factory PCCB
Porsche GT4RS (718) w/ factory PCCB
This 410mm Girodisc conversion system is a direct front rotor replacement for the Porsche 991.1 or 991.2 GT3, GT3RS, GT2RS, and GT4RS originally equipped with PCCB brakes. These two-piece floating iron rotors with aluminum hats will bolt directly to your Porsche and work flawlessly with the OEM front calipers.
You must use must use the pad shape used on the 991 GT3 with iron rotors. The annulus (pad swept height) of these rotors is smaller than the PCCBs to keep rotor weight low and allow far better pad selection.
By upgrading your brakes with lightweight, high-performance Girodisc rotors, especially when paired with Girodisc A2-154 rear rotors, your Porsche's factory brake bias and ABS efficiency are maintained.
The low rotational mass and unsprung weight of Girodisc rotors allows for quick acceleration and fast transient suspension response. Most racers replace the factory PCCBs with Girodisc rotors to avoid the inevitable damage to fragile carbon-ceramic discs when swapping wheels at the track.
We suggest using these rotors with these Pagid 4924 or PFC brake pad profiles normally used in the Porsche 991 GT3 without PCCB. When combined with Competition Motorsport RF1 Racing brake fluid or the New HALO P1 High Performance Brake Fluid, you'll have an extremely reliable and durable solution to cracked or broken carbon-ceramic rotors at a fraction of the cost of factory PCCBs.
The central hat section of the Girodisc is made from 6061-T6 aircraft specification aluminum. The disc is manufactured from cast iron constructed in the USA, made to the same specification with the same material used by professional racing organizations. The rotors' curved vane design was developed in racing and acts as a centrifugal pump to force cooling air through the disc.
The rotor and hat mount together through a floating mount system which utilizes ten high strength alloy steel drive pins manufactured by Girodisc in the USA to their own specifications and are cadmium plated for corrosion resistance. The alloy drive pins transfer the load from the brake action while maintaining the axial and radial float between the disc rotor and hat. The pins are secured by Grade-12 cap screws with hardened washers and mounted with anti-noise spring washers to allow for heat expansion while eliminating the rattle and noise associated with floating rotors.
The two-piece Girodisc design allows for disc-only replacement as well, minimizing future replacement costs and delivering outstanding performance.
Sold/priced per pair.

Girodisc
A2-154 Girodisc 2pc REAR Brake Rotors for Porsche (OEM PCCB)
$1,995.00
Girodisc A2-154 390mm Rear Iron Rotor Conversion
Fits The Following Cars With OEM PCCB:
Porsche 991.1 and 991.2 GT3
Porsche 991.1 and 991.2 GT3RS
Porsche 991.2 GT2RS
Porsche 718 Cayman GT4RS
This 390mm Girodisc conversion system is a rear rotor direct replacement for any Porsche 991 GT3, GT3RS, GT2RS, and GT4RS originally equipped with PCCB brakes. These two-piece floating iron rotors will bolt directly to the car and work with your OEM calipers perfectly.
By upgrading your brakes with these lightweight, high-performance Girodisc rotors (paired with the A1-154 front rotors), your factory brake bias and ABS efficiency are maintained. The low rotational and unsprung weight allows for quicker acceleration and transient suspension response. Most racers replace the factory PCCBs with steel two-piece rotors to avoid the inevitable damage to the fragile carbon ceramic discs when swapping wheels at the track!
When used with Pagid or PFC performance brake pads and CMS RF1 racing brake fluid, you have an powerful, durable solution to cracked or broken carbon-ceramic rotors at a fraction of the cost of replacing the factory PCCB units.
The central hat section of each Girodisc is made from 6061-T6 aircraft specification aluminum. The disc is manufactured from cast iron constructed in the USA, made to the same specification with the same material used by professional racing organizations. The rotors' curved vane design was developed in racing and acts as a centrifugal pump to force cooling air through the disc.
The rotor and hat mount together through a floating mount system which utilizes ten high strength alloy steel drive pins manufactured by Girodisc in the USA to their own specifications and are cadmium plated for corrosion resistance. The alloy drive pins transfer the load from the brake action while maintaining the axial and radial float between the disc rotor and hat. The pins are secured by class 12.9 cap screws with hardened washers and mounted with anti-noise spring washers to allow for heat expansion while eliminating the rattle and noise associated with floating rotors.
The two-piece Girodisc design allows for disc-only replacement as well, minimizing future replacement costs and delivering outstanding performance.
Sold/priced per pair.

Performance Friction
PFC Performance Friction 410mm Replacement Front Brake Rotors for Porsche (OEM PCCB)
$1,399.00
Performance Friction PFC 410.34.0063.451/461 410mm Replacement Front Floating Racing Brake Rotors
Fit The Following Cars which use PFC 410.069.63/64 (w/ OEM Iron Rotors or PCCB Rotors) - Center hat Excluded, rotor disc only. Replacement Disc Only For PFC 410.069.63/64 and
410.057.63/64
Porsche 992 GT3 PCCB/Iron (Front)
Porsche 992 GT3RS PCCB/Iron (Front)
Porsche 991 GT2RS PCCB (Front)
Porsche 991 GT3 PCCB (Front)
Porsche 991 GT3RS PCCB (Front)
Porsche 718 / 982 GT4RS PCCB or Iron (Front)
Porsche 718 GT4 PCCB (Front)
PFC the manufacturer of Porsche Cup braking systems developed a 410mm front rotor replacement kit that is a direct replacement for the OEM 991 GT or 718 GT4 PCCB Brake rotors or OEM 718 / 982 GT4RS with PCCB or Iron rotors.
Performance Friction PFC V3 Discs with Zero Failure Technology
Unique Rotor and Hat interface, eliminating most hardware. The elimination of hardware reduces weight, complexity, and installation time for less down time and more seat time on the track. Replace your rotor discs in minutes with a flat head screwdriver
PFC metallurgy specified for high Thermal stability and mechanical strength for increased longevity
48 vane geometry engineered for increased airflow for increased brake cooling during the heat of the battle while on track
Patented slot pattern for increased initial bit and pad surface conditioning
Lightweight forged hard anodized aluminum hat for increased durability and performance
The two-piece PFC V3 design allows for disc-only replacement as well, minimizing future replacement costs and delivering outstanding performance.
Sold/priced per pair.

Performance Friction
PFC Performance Friction 380mm Replacement Front Brake Rotors for Porsche (OEM Iron)
$1,118.00
Performance Friction PFC 380.34.0062.451/461 380mm Front Floating Racing Brake Rotor Replacements
Fit The Following Cars (w/ OEM Iron Rotors) - Center hat Excluded, rotor disc only. Replacement Disc Only For PFC 380.070.63/64
Porsche 991 GT3 (Front)
Porsche 991 GT3RS (Front)
Porsche 981 GT4 (Front)
PFC the manufacturer of Porsche Cup braking systems developed a 380x34mm front rotor replacement kit that is a direct replacement for the OEM Iron Brake rotors.
Performance Friction PFC V3 Discs with Zero Failure Technology
Unique Rotor and Hat interface, eliminating most hardware. The elimination of hardware reduces weight, complexity, and installation time for less down time and more seat time on the track. Replace your rotor discs in minutes with a flat head screwdriver
PFC metallurgy specified for high Thermal stability and mechanical strength for increased longevity
48 vane geometry engineered for increased airflow for increased brake cooling during the heat of the battle while on track
Patented slot pattern for increased initial bit and pad surface conditioning
Lightweight forged hard anodized aluminum hat for increased durability and performance
The two-piece PFC V3 design allows for disc-only replacement as well, minimizing future replacement costs and delivering outstanding performance.
Sold/priced per pair.

Performance Friction
PFC Performance Friction 410mm 2pc Front Brake Rotors for Porsche (OEM PCCB)
$2,589.00
Performance Friction PFC 410.069.63-64 410mm Two-Piece Front Floating Racing Brake Rotors
Fit The Following Cars (w/ OEM Iron Rotors or PCCB Rotors)
Porsche 991 GT2RS PCCB (Front)
Porsche 991 GT3 PCCB (Front)
Porsche 991 GT3RS PCCB (Front)
Porsche 718 / 982 GT4RS PCCB or Iron (Front)
Porsche 718 GT4 PCCB (Front)
PFC the manufacturer of Porsche Cup braking systems developed a 410mm front rotor replacement kit that is a direct replacement for the OEM 991 GT or 718 GT4 PCCB Brake rotors or OEM 718 / 982 GT4RS with PCCB or Iron rotors.
Performance Friction PFC V3 Disks with Zero Failure Technology
Unique Rotor and Hat interface, eliminating most hardware. The elimination of hardware reduces weight, complexity, and installation time for less down time and more seat time on the track. Replace your rotor discs in minutes with a flat head screwdriver
PFC metallurgy specified for high Thermal stability and mechanical strength for increased longevity
48 vane geometry engineered for increased airflow for increased brake cooling during the heat of the battle while on track
Patented slot pattern for increased initial bit and pad surface conditioning
Lightweight forged hard anodized aluminum hat for increased durability and performance
The two-piece PFC V3 design allows for disc-only replacement as well, minimizing future replacement costs and delivering outstanding performance.
Sold/priced per pair.

AP Racing
AP Racing 410x36mm Replacement Front Brake Rotor Rings for Porsche (OEM PCCB)
$1,596.00
AP Racing J Hook 410x36mm Replacement Front Brake Rotor Rings
This is a pair of replacement front rotor rings with new hardware included. Center hat is not included, this kit is rotor rings and hardware only. Replacement discs only for AP Racing 13.01.20025 rotors.
Fits the Following Cars (w/ OEM PCCB rotors):
Porsche 991 GT2RS PCCB (Front)
Porsche 991 GT3 PCCB (Front)
Porsche 991 GT3RS PCCB (Front)
Porsche 718 GT4 PCCB (Front)
Sold/priced per pair of rotor rings with hardware.
AP Racing J Hook Brake Rotors – The Gold Standard in Track Day & Racing Performance
Engineered for professional motorsport, HPDE, and dedicated track day use, AP Racing’s J Hook Brake Rotors deliver uncompromising performance, thermal stability, and consistent braking power. These two-piece, floating rotors are built to handle the extreme demands of road racing, with design features derived from over 50 years of elite competition—including Formula 1, NASCAR, and IMSA.
Unlike conventional one-piece rotors, AP Racing’s two-piece floating design features a billet aluminum hat mated to a cast iron disc via precision-engineered bobbins. This setup allows for controlled radial expansion under high heat, minimizing distortion and coning. The result? More even pad wear, a firmer pedal feel, and longer component life, even during extended lapping sessions or endurance racing. Floating hardware includes anti-knock back spring clips that reduce piston retraction while eliminating common NVH issues like rattling.
Why Choose AP Racing J Hook Rotors? Advanced Cooling, Superior Bite, Unmatched Durability
At the heart of every rotor is AP Racing’s proprietary high-carbon iron alloy, developed to withstand repeated thermal cycling without cracking or warping. Internally, directional vanes—far superior to OEM pillar or straight vane designs—maximize airflow and cooling. With 60 to 84 vanes per rotor, AP Racing achieves faster heat evacuation, reduced brake fade, and a more consistent friction surface. These rotors are left/right-specific for optimal airflow and balance.
The exclusive J Hook slot pattern offers enhanced initial bite and promotes uniform heat distribution across the rotor face, reducing pad deposits and vibration. Unlike drilled rotors or straight-slot competitors, the J Hook design provides cleaner pad transfer during bed-in and superior modulation under braking—ideal for serious drivers who demand feedback and control. Yes, you might hear a little more whirr, but you’ll gain the stopping power, consistency, and longevity your lap times demand.
Premium Components, Affordable Performance
The rotor hats are CNC-machined from 6061-T6 billet aluminum and hard anodized for strength and heat resistance. Scalloped edges under the hat further assist heat dissipation. All hardware is U.S.-made to AP Racing spec, the same quality found on pro-level racing platforms.
And while these rotors are race-proven, they’re also surprisingly cost-effective to replace. Don’t settle for cheap rotors that crack after a weekend—AP’s J Hook rings offer better durability and real long-term value. Fewer replacements mean more track time, less downtime, and peace of mind knowing you're running the best.
Used by Champions. Trusted by Experts.
From endurance racers to HPDE enthusiasts, AP Racing brake rotors are trusted worldwide for their reliability, longevity, and performance under pressure. Whether you're shaving seconds off your lap time or building a dedicated track car, the J Hook delivers a professional-grade solution that won’t let you down.
AP Racing by Essex 2-piece Competition J Hook front iron disc pair for 991 GT3/RS and 718 GT4/Spyder RS to replace PCCB discs.
410x36mm (16.14" x 1.40")
Huge increase in airflow, cooling capacity, and durability vs. OEM PCCB discs
Drastically less expense long-term running costs vs. PCCB
Must use the standard front 991 GT3/RS pad shape used in the OEM iron rotors system
Not compatible with OEM PCCB pad shape
Over twice as many internal cooling vanes as the OEM PCCB's
Weighs almost the same as the OEM 380x34mm iron discs, despite much larger size
Designed for: club racing, time trial, auto-x, HPDE
Works with OEM calipers and wheels, no modifications required
Ultralight, fully floating, anodized billet aluminum hat with float control/anti-rattle clips
AP Racing J Hook Brake Rotors for Auto Racing, Track Days & HPDE
Why Rotor Design Matters: Heat Expansion and Floating Technology
As with most metals, iron brake discs expand significantly under heat. When temperatures rise, the disc grows radially—expanding in both diameter and circumference. Traditional one-piece rotors struggle to accommodate this natural expansion. As the outer edge pulls away from the center under heat stress, it creates a condition called “coning”—a distortion that compromises pad-to-rotor contact. This distortion can lead to uneven pad wear, brake tapering, and an inconsistent, long brake pedal.
AP Racing two-piece floating brake rotors are purpose-built to eliminate these issues. Engineered with “float” built into the disc or hat assembly, these rotors feature oblong-shaped mounting holes that allow the hardware to slide as the disc heats up. This flexibility ensures the disc runs true within the caliper under high-temperature loads, effectively reducing distortion, minimizing pad taper and stress cracks, and promoting longer component life.
Custom Mounting Hardware & Anti-Knock Back Spring Clips
AP Racing rotors utilize application-specific, U.S.-made mounting hardware—not generic bolts. These premium components are the exact parts used in AP’s professional motorsport products, engineered to withstand the rigors of competitive racing.
To manage lateral disc motion that can push caliper pistons backward (known as knock back), AP Racing integrates anti-knock back spring clips on alternating bobbins—five on a ten-bolt setup, six on a twelve-bolt disc. These clips keep the aluminum hat and iron disc ring properly aligned while still allowing for radial float. Bonus: they eliminate annoying rattles and vibrations, ensuring a quieter, more refined braking experience.
High-Performance Hat Design for Heat Isolation
The disc hats in AP Racing’s two-piece floating rotors are CNC-machined from 6061-T6 billet aluminum and finished with a hard anodized coating. This high-strength aluminum alloy was selected for its ability to maintain structural integrity even at elevated temperatures. AP adds scalloped channels beneath the hat to further encourage airflow and heat evacuation from the outer disc face, minimizing thermal transfer to hubs and wheel bearings—helping reduce maintenance costs on these expensive components.
Internal Vane Engineering: Airflow Optimization & Thermal Stability
AP Racing’s internal vane design sets them apart from OEM and most aftermarket competitors. While many factory brake discs use non-directional pillar vanes (low-cost and NVH-focused), AP Racing rotors use directional vanes engineered for maximum airflow. These rotors are side-specific—meaning you’ll receive a unique left and right disc in each set—ensuring optimized cooling through strategic vane orientation and shape.
Beyond that, AP Racing rotors feature a superior vane count, typically ranging from 60 to 84 vanes, compared to 30–48 in most aftermarket rotors. After extensive CFD and thermal analysis, this high vane count was proven to:
Increase airspeed and thermal transfer
Reduce recirculation and deflection at the disc face
Minimize coning, cracking, and brake fade
Deliver more even pad contact and extended rotor life
J Hook Slot Pattern: Exclusive to AP Racing
Slots and drill holes may improve initial bite, but they also introduce “cool spots” in the rotor face—areas of uneven heating that can lead to stress risers, cracks, and pad vibration. OEM rotors often avoid this by leaving the disc face blank, but that compromises bite and brake feel.
AP Racing’s patented J Hook design, developed through rigorous R&D, solves this problem. The hooks are meticulously spaced around the disc’s circumference and from hat to edge, forming a continuous distortion path that ensures even heat distribution. This encourages uniform pad deposits during bed-in, helps reduce judder and cracking, and improves consistency under repeated high-load braking.
In addition, the J Hook slots provide more leading edges for pads to grip than traditional curved slots or blank rotors. While this might generate a mild whirring sound during braking, the benefits—more bite, cleaner bedding, better pedal feel—make it the top choice for committed racers and serious track day drivers.
Metallurgy Backed by 50+ Years of Motorsport Leadership
AP Racing's reputation is built on performance, and their proprietary iron alloy used in J Hook rotors is no exception. Drawing from over five decades of elite motorsport experience, including 750+ Formula 1 wins and widespread use across NASCAR, AP’s engineers have developed a disc alloy that excels under sustained racing temperatures and stress. Where OEM discs focus on affordability and mass production, AP Racing’s J Hook rotors are purpose-built for motorsport durability and heat resistance.
Affordable Replacement Cost: Serious Value for Serious Drivers
Even the best brake rotors are consumables. When you drive hard—especially at the track—your discs will eventually wear out. That’s why AP Racing designed their replacement iron rings to be cost-effective, allowing you to replace worn parts without breaking the bank.
Compare that to constantly buying cheap $150 rotors every weekend—rotors that can't handle the heat and need to be swapped frequently. With AP Racing’s J Hook rotors, you get longer service intervals, less downtime, and better performance over time, making them an incredibly smart long-term investment.
Proven on Track. Trusted by Champions.
Top-tier racing teams rely on AP Racing J Hook rotors for one reason: they perform under pressure. Whether you're running time trials, attending HPDE events, or competing in wheel-to-wheel racing, these rotors offer professional-grade reliability, safety, and performance.
Bedding and Preparation of AP Racing J Hook Discs
Properly preparing your new brake discs before heavy use is extremely important. The goal of bedding-in your brake pads and discs is to mate them together properly and prepare them for heavy use. When prepared properly, or bed-in, your pads will transfer a thin layer of material to the disc face (transfer layer). The pads in your caliper will then actually ride on that thin layer of pad material you’ve put down on the rotor, rather than rubbing directly on the iron rotor face. A good transfer layer is going to give you superior brake pedal feel, less noise, superior pad wear, and lower the chances of cracking your discs.
Important Notes- PLEASE READ! First, make sure you are on a closed course to perform a proper bed-in. Do NOT perform the procedure on public roads. You need a stretch of asphalt with long straights, good visibility, and no potential obstructions. Make sure you are in a position to safely and repeatedly attain the necessary speeds to perform the bed-in procedure. A controlled racetrack is the best place to perform this procedure. AP Racing and Competition Motorsport in no way suggest or condone speeding on public roads or breaking the law in your car, nor do we take responsibility for any damage or injury that occurs as a result of using our product or these procedures. You are performing the bed-in procedure at your own risk.
During these procedures, it’s critical that you never come to a complete stop with your foot on the brake pedal. If you have brake ducts on your car, you may want to block them off to allow your brake system to heat up easily. The procedure outlined below is a generic procedure for most types of mild race pad. Please check your pad manufacturer’s recommended bed-in procedure.
Accelerate to approximately 60mph and then decelerate down to 5 mph. If your car has ABS, you should try to hold the brakes at a point just before ABS intervention.
Once the car slows to 5mph, immediately accelerate back up to about 60mph, and brake again to roughly 5mph.
Repeat this series of stopping and accelerating 8 to 10 times. Again, do not come to a complete stop with your foot on the brake pedal.
Cool the brake system down by cruising at 45mph+ for 5 to 10 minutes.
Visually inspect your discs. They should be a blue/grey color (instead of shiny silver), and have an even layer of pad material across and around the entire rotor face.
If the AP Racing rotors don’t have a layer of pad material on them, perform another series of stops in the manner outlined above.

Performance Friction
AP Racing 380mmx34mm Replacement J Hook Front Brake Rotors for Porsche (OEM Iron)
$1,236.00
AP Racing 380x34mm Replacement J Hook Front Floating Racing Brake Rotors
Fit The Following Cars (w/ OEM Iron Rotors)- Center hat Excluded, rotor discs and hardware only. Replacement Disc Only For AP Racing 13.01.20017
Fit The Following Cars (w/ OEM Iron Rotors)
Porsche 991 GT3 (Front)
Porsche 991 GT3RS (Front)
Porsche 981 GT4 (Front)
AP Racing by Essex 2-piece Competition J Hook front disc pair for 981 GT4, 991.1 & 991.2 GT3 & GT3 RS with iron discs
380mm x 34mm (14.96" x 1.34") 72 Vane, D66
Huge increase in airflow, cooling capacity, and durability vs. OEM discs
Saves 2 lbs. unsprung weight per side vs. OEM iron discs
Designed for: club racing, time trial, auto-x, HPDE
Works with OEM calipers, no modifications required
Ultralight, fully floating, anodized billet aluminum hat with float control/anti-rattle clips
Sold/priced per pair of rotor rings (including hardware).
AP Racing J Hook Brake Rotors – The Gold Standard in Track Day & Racing Performance
Engineered for professional motorsport, HPDE, and dedicated track day use, AP Racing’s J Hook Brake Rotors deliver uncompromising performance, thermal stability, and consistent braking power. These two-piece, floating rotors are built to handle the extreme demands of road racing, with design features derived from over 50 years of elite competition—including Formula 1, NASCAR, and IMSA.
Unlike conventional one-piece rotors, AP Racing’s two-piece floating design features a billet aluminum hat mated to a cast iron disc via precision-engineered bobbins. This setup allows for controlled radial expansion under high heat, minimizing distortion and coning. The result? More even pad wear, a firmer pedal feel, and longer component life, even during extended lapping sessions or endurance racing. Floating hardware includes anti-knockback spring clips that reduce piston retraction while eliminating common NVH issues like rattling.
Why Choose AP Racing J Hook Rotors? Advanced Cooling, Superior Bite, Unmatched Durability
At the heart of every rotor is AP Racing’s proprietary high-carbon iron alloy, developed to withstand repeated thermal cycling without cracking or warping. Internally, directional vanes—far superior to OEM pillar or straight vane designs—maximize airflow and cooling. With 60 to 84 vanes per rotor, AP Racing achieves faster heat evacuation, reduced brake fade, and a more consistent friction surface. These rotors are left/right-specific for optimal airflow and balance.
The exclusive J Hook slot pattern offers enhanced initial bite and promotes uniform heat distribution across the rotor face, reducing pad deposits and vibration. Unlike drilled rotors or straight-slot competitors, the J Hook design provides cleaner pad transfer during bed-in and superior modulation under braking—ideal for serious drivers who demand feedback and control. Yes, you might hear a little more whirr, but you’ll gain the stopping power, consistency, and longevity your lap times demand.
Premium Components, Affordable Performance
The rotor hats are CNC-machined from 6061-T6 billet aluminum and hard anodized for strength and heat resistance. Scalloped edges under the hat further assist heat dissipation. All hardware is U.S.-made to AP Racing spec, the same quality found on pro-level racing platforms.
And while these rotors are race-proven, they’re also surprisingly cost-effective to replace. Don’t settle for cheap rotors that crack after a weekend—AP’s J Hook rings offer better durability and real long-term value. Fewer replacements mean more track time, less downtime, and peace of mind knowing you're running the best.
Used by Champions. Trusted by Experts.
From endurance racers to HPDE enthusiasts, AP Racing brake rotors are trusted worldwide for their reliability, longevity, and performance under pressure. Whether you're shaving seconds off your lap time or building a dedicated track car, the J Hook delivers a professional-grade solution that won’t let you down.
AP Racing J Hook Brake Rotors for Auto Racing, Track Days & HPDE
Why Rotor Design Matters: Heat Expansion and Floating Technology
As with most metals, iron brake discs expand significantly under heat. When temperatures rise, the disc grows radially—expanding in both diameter and circumference. Traditional one-piece rotors struggle to accommodate this natural expansion. As the outer edge pulls away from the center under heat stress, it creates a condition called “coning”—a distortion that compromises pad-to-rotor contact. This distortion can lead to uneven pad wear, brake tapering, and an inconsistent, long brake pedal.
AP Racing two-piece floating brake rotors are purpose-built to eliminate these issues. Engineered with “float” built into the disc or hat assembly, these rotors feature oblong-shaped mounting holes that allow the hardware to slide as the disc heats up. This flexibility ensures the disc runs true within the caliper under high-temperature loads, effectively reducing distortion, minimizing pad taper and stress cracks, and promoting longer component life.
Custom Mounting Hardware & Anti-Knockback Spring Clips
AP Racing rotors utilize application-specific, U.S.-made mounting hardware—not generic bolts. These premium components are the exact parts used in AP’s professional motorsport products, engineered to withstand the rigors of competitive racing.
To manage lateral disc motion that can push caliper pistons backward (known as knockback), AP Racing integrates anti-knockback spring clips on alternating bobbins—five on a ten-bolt setup, six on a twelve-bolt disc. These clips keep the aluminum hat and iron disc ring properly aligned while still allowing for radial float. Bonus: they eliminate annoying rattles and vibrations, ensuring a quieter, more refined braking experience.
High-Performance Hat Design for Heat Isolation
The disc hats in AP Racing’s two-piece floating rotors are CNC-machined from 6061-T6 billet aluminum and finished with a hard anodized coating. This high-strength aluminum alloy was selected for its ability to maintain structural integrity even at elevated temperatures. AP adds scalloped channels beneath the hat to further encourage airflow and heat evacuation from the outer disc face, minimizing thermal transfer to hubs and wheel bearings—helping reduce maintenance costs on these expensive components.
Internal Vane Engineering: Airflow Optimization & Thermal Stability
AP Racing’s internal vane design sets them apart from OEM and most aftermarket competitors. While many factory brake discs use non-directional pillar vanes (low-cost and NVH-focused), AP Racing rotors use directional vanes engineered for maximum airflow. These rotors are side-specific—meaning you’ll receive a unique left and right disc in each set—ensuring optimized cooling through strategic vane orientation and shape.
Beyond that, AP Racing rotors feature a superior vane count, typically ranging from 60 to 84 vanes, compared to 30–48 in most aftermarket rotors. After extensive CFD and thermal analysis, this high vane count was proven to:
Increase airspeed and thermal transfer
Reduce recirculation and deflection at the disc face
Minimize coning, cracking, and brake fade
Deliver more even pad contact and extended rotor life
J Hook Slot Pattern: Exclusive to AP Racing
Slots and drill holes may improve initial bite, but they also introduce “cool spots” in the rotor face—areas of uneven heating that can lead to stress risers, cracks, and pad vibration. OEM rotors often avoid this by leaving the disc face blank, but that compromises bite and brake feel.
AP Racing’s patented J Hook design, developed through rigorous R&D, solves this problem. The hooks are meticulously spaced around the disc’s circumference and from hat to edge, forming a continuous distortion path that ensures even heat distribution. This encourages uniform pad deposits during bed-in, helps reduce judder and cracking, and improves consistency under repeated high-load braking.
In addition, the J Hook slots provide more leading edges for pads to grip than traditional curved slots or blank rotors. While this might generate a mild whirring sound during braking, the benefits—more bite, cleaner bedding, better pedal feel—make it the top choice for committed racers and serious track day drivers.
Metallurgy Backed by 50+ Years of Motorsport Leadership
AP Racing's reputation is built on performance, and their proprietary iron alloy used in J Hook rotors is no exception. Drawing from over five decades of elite motorsport experience, including 750+ Formula 1 wins and widespread use across NASCAR, AP’s engineers have developed a disc alloy that excels under sustained racing temperatures and stress. Where OEM discs focus on affordability and mass production, AP Racing’s J Hook rotors are purpose-built for motorsport durability and heat resistance.
Affordable Replacement Cost: Serious Value for Serious Drivers
Even the best brake rotors are consumables. When you drive hard—especially at the track—your discs will eventually wear out. That’s why AP Racing designed their replacement iron rings to be cost-effective, allowing you to replace worn parts without breaking the bank.
Compare that to constantly buying cheap $150 rotors every weekend—rotors that can't handle the heat and need to be swapped frequently. With AP Racing’s J Hook rotors, you get longer service intervals, less downtime, and better performance over time, making them an incredibly smart long-term investment.
Proven on Track. Trusted by Champions.
Top-tier racing teams rely on AP Racing J Hook rotors for one reason: they perform under pressure. Whether you're running time trials, attending HPDE events, or competing in wheel-to-wheel racing, these rotors offer professional-grade reliability, safety, and performance.
Bedding and preparation of AP Racing J Hook Disc
Properly preparing your new brake discs before heavy use is extremely important. The goal of bedding-in your brake pads and discs is to mate them together properly and prepare them for heavy use. When prepared properly, or bed-in, your pads will transfer a thin layer of material to the disc face (transfer layer). The pads in your caliper will then actually ride on that thin layer of pad material you’ve put down on the rotor, rather than rubbing directly on the iron rotor face. A good transfer layer is going to give you superior brake pedal feel, less noise, superior pad wear, and lower the chances of cracking your discs.
Important Notes- PLEASE READ! First, make sure you are on a closed course to perform a proper bed-in. Do NOT perform the procedure on public roads. You need a stretch of asphalt with long straights, good visibility, and no potential obstructions. Make sure you are in a position to safely and repeatedly attain the necessary speeds to perform the bed-in procedure. A controlled racetrack is the best place to perform this procedure. AP Racing and Competition Motorsport in no way suggest or condone speeding on public roads or breaking the law in your car, nor do we take responsibility for any damage or injury that occurs as a result of using our product or these procedures. You are performing the bed-in procedure at your own risk.
During these procedures, it’s critical that you never come to a complete stop with your foot on the brake pedal. If you have brake ducts on your car, you may want to block them off to allow your brake system to heat up easily. The procedure outlined below is a generic procedure for most types of mild race pad. Please check your pad manufacturer’s recommended bed-in procedure.
Accelerate to approximately 60mph and then decelerate down to 5 mph. If your car has ABS, you should try to hold the brakes at a point just before ABS intervention.
Once the car slows to 5mph, immediately accelerate back up to about 60mph, and brake again to roughly 5mph.
Repeat this series of stopping and accelerating 8 to 10 times. Again, do not come to a complete stop with your foot on the brake pedal.
Cool the brake system down by cruising at 45mph+ for 5 to 10 minutes.
Visually inspect your discs. They should be a blue/grey color (instead of shiny silver), and have an even layer of pad material across and around the entire rotor face.
If the AP Racing rotors don’t have a layer of pad material on them, perform another series of stops in the manner outlined above.

Performance Friction
AP Racing 380mmx34mm 2-piece J Hook Front Brake Rotors for Porsche (OEM Iron)
$2,099.00
AP Racing 380x34mm 2-piece J Hook Front Floating Racing Brake Rotors
Fit The Following Cars (w/ OEM Iron Rotors)
Porsche 991 GT3 (Front)
Porsche 991 GT3RS (Front)
Porsche 981 GT4 (Front)
AP Racing by Essex 2-piece Competition J Hook front disc pair for 981 GT4, 991.1 & 991.2 GT3 & GT3 RS with iron discs
380mm x 34mm (14.96" x 1.34") 72 Vane, D66
Huge increase in airflow, cooling capacity, and durability vs. OEM discs
Saves 2 lbs. unsprung weight per side vs. OEM iron discs
Designed for: club racing, time trial, auto-x, HPDE
Works with OEM calipers, no modifications required
Ultralight, fully floating, anodized billet aluminum hat with float control/anti-rattle clips
Sold/priced per pair.
AP Racing J Hook Brake Rotors – The Gold Standard in Track Day & Racing Performance
Engineered for professional motorsport, HPDE, and dedicated track day use, AP Racing’s J Hook Brake Rotors deliver uncompromising performance, thermal stability, and consistent braking power. These two-piece, floating rotors are built to handle the extreme demands of road racing, with design features derived from over 50 years of elite competition—including Formula 1, NASCAR, and IMSA.
Unlike conventional one-piece rotors, AP Racing’s two-piece floating design features a billet aluminum hat mated to a cast iron disc via precision-engineered bobbins. This setup allows for controlled radial expansion under high heat, minimizing distortion and coning. The result? More even pad wear, a firmer pedal feel, and longer component life, even during extended lapping sessions or endurance racing. Floating hardware includes anti-knockback spring clips that reduce piston retraction while eliminating common NVH issues like rattling.
Why Choose AP Racing J Hook Rotors? Advanced Cooling, Superior Bite, Unmatched Durability
At the heart of every rotor is AP Racing’s proprietary high-carbon iron alloy, developed to withstand repeated thermal cycling without cracking or warping. Internally, directional vanes—far superior to OEM pillar or straight vane designs—maximize airflow and cooling. With 60 to 84 vanes per rotor, AP Racing achieves faster heat evacuation, reduced brake fade, and a more consistent friction surface. These rotors are left/right-specific for optimal airflow and balance.
The exclusive J Hook slot pattern offers enhanced initial bite and promotes uniform heat distribution across the rotor face, reducing pad deposits and vibration. Unlike drilled rotors or straight-slot competitors, the J Hook design provides cleaner pad transfer during bed-in and superior modulation under braking—ideal for serious drivers who demand feedback and control. Yes, you might hear a little more whirr, but you’ll gain the stopping power, consistency, and longevity your lap times demand.
Premium Components, Affordable Performance
The rotor hats are CNC-machined from 6061-T6 billet aluminum and hard anodized for strength and heat resistance. Scalloped edges under the hat further assist heat dissipation. All hardware is U.S.-made to AP Racing spec, the same quality found on pro-level racing platforms.
And while these rotors are race-proven, they’re also surprisingly cost-effective to replace. Don’t settle for cheap rotors that crack after a weekend—AP’s J Hook rings offer better durability and real long-term value. Fewer replacements mean more track time, less downtime, and peace of mind knowing you're running the best.
Used by Champions. Trusted by Experts.
From endurance racers to HPDE enthusiasts, AP Racing brake rotors are trusted worldwide for their reliability, longevity, and performance under pressure. Whether you're shaving seconds off your lap time or building a dedicated track car, the J Hook delivers a professional-grade solution that won’t let you down.
AP Racing J Hook Brake Rotors for Auto Racing, Track Days & HPDE
Why Rotor Design Matters: Heat Expansion and Floating Technology
As with most metals, iron brake discs expand significantly under heat. When temperatures rise, the disc grows radially—expanding in both diameter and circumference. Traditional one-piece rotors struggle to accommodate this natural expansion. As the outer edge pulls away from the center under heat stress, it creates a condition called “coning”—a distortion that compromises pad-to-rotor contact. This distortion can lead to uneven pad wear, brake tapering, and an inconsistent, long brake pedal.
AP Racing two-piece floating brake rotors are purpose-built to eliminate these issues. Engineered with “float” built into the disc or hat assembly, these rotors feature oblong-shaped mounting holes that allow the hardware to slide as the disc heats up. This flexibility ensures the disc runs true within the caliper under high-temperature loads, effectively reducing distortion, minimizing pad taper and stress cracks, and promoting longer component life.
Custom Mounting Hardware & Anti-Knockback Spring Clips
AP Racing rotors utilize application-specific, U.S.-made mounting hardware—not generic bolts. These premium components are the exact parts used in AP’s professional motorsport products, engineered to withstand the rigors of competitive racing.
To manage lateral disc motion that can push caliper pistons backward (known as knockback), AP Racing integrates anti-knockback spring clips on alternating bobbins—five on a ten-bolt setup, six on a twelve-bolt disc. These clips keep the aluminum hat and iron disc ring properly aligned while still allowing for radial float. Bonus: they eliminate annoying rattles and vibrations, ensuring a quieter, more refined braking experience.
High-Performance Hat Design for Heat Isolation
The disc hats in AP Racing’s two-piece floating rotors are CNC-machined from 6061-T6 billet aluminum and finished with a hard anodized coating. This high-strength aluminum alloy was selected for its ability to maintain structural integrity even at elevated temperatures. AP adds scalloped channels beneath the hat to further encourage airflow and heat evacuation from the outer disc face, minimizing thermal transfer to hubs and wheel bearings—helping reduce maintenance costs on these expensive components.
Internal Vane Engineering: Airflow Optimization & Thermal Stability
AP Racing’s internal vane design sets them apart from OEM and most aftermarket competitors. While many factory brake discs use non-directional pillar vanes (low-cost and NVH-focused), AP Racing rotors use directional vanes engineered for maximum airflow. These rotors are side-specific—meaning you’ll receive a unique left and right disc in each set—ensuring optimized cooling through strategic vane orientation and shape.
Beyond that, AP Racing rotors feature a superior vane count, typically ranging from 60 to 84 vanes, compared to 30–48 in most aftermarket rotors. After extensive CFD and thermal analysis, this high vane count was proven to:
Increase airspeed and thermal transfer
Reduce recirculation and deflection at the disc face
Minimize coning, cracking, and brake fade
Deliver more even pad contact and extended rotor life
J Hook Slot Pattern: Exclusive to AP Racing
Slots and drill holes may improve initial bite, but they also introduce “cool spots” in the rotor face—areas of uneven heating that can lead to stress risers, cracks, and pad vibration. OEM rotors often avoid this by leaving the disc face blank, but that compromises bite and brake feel.
AP Racing’s patented J Hook design, developed through rigorous R&D, solves this problem. The hooks are meticulously spaced around the disc’s circumference and from hat to edge, forming a continuous distortion path that ensures even heat distribution. This encourages uniform pad deposits during bed-in, helps reduce judder and cracking, and improves consistency under repeated high-load braking.
In addition, the J Hook slots provide more leading edges for pads to grip than traditional curved slots or blank rotors. While this might generate a mild whirring sound during braking, the benefits—more bite, cleaner bedding, better pedal feel—make it the top choice for committed racers and serious track day drivers.
Metallurgy Backed by 50+ Years of Motorsport Leadership
AP Racing's reputation is built on performance, and their proprietary iron alloy used in J Hook rotors is no exception. Drawing from over five decades of elite motorsport experience, including 750+ Formula 1 wins and widespread use across NASCAR, AP’s engineers have developed a disc alloy that excels under sustained racing temperatures and stress. Where OEM discs focus on affordability and mass production, AP Racing’s J Hook rotors are purpose-built for motorsport durability and heat resistance.
Affordable Replacement Cost: Serious Value for Serious Drivers
Even the best brake rotors are consumables. When you drive hard—especially at the track—your discs will eventually wear out. That’s why AP Racing designed their replacement iron rings to be cost-effective, allowing you to replace worn parts without breaking the bank.
Compare that to constantly buying cheap $150 rotors every weekend—rotors that can't handle the heat and need to be swapped frequently. With AP Racing’s J Hook rotors, you get longer service intervals, less downtime, and better performance over time, making them an incredibly smart long-term investment.
Proven on Track. Trusted by Champions.
Top-tier racing teams rely on AP Racing J Hook rotors for one reason: they perform under pressure. Whether you're running time trials, attending HPDE events, or competing in wheel-to-wheel racing, these rotors offer professional-grade reliability, safety, and performance.
Bedding and preparation of AP Racing J Hook Disc
Properly preparing your new brake discs before heavy use is extremely important. The goal of bedding-in your brake pads and discs is to mate them together properly and prepare them for heavy use. When prepared properly, or bed-in, your pads will transfer a thin layer of material to the disc face (transfer layer). The pads in your caliper will then actually ride on that thin layer of pad material you’ve put down on the rotor, rather than rubbing directly on the iron rotor face. A good transfer layer is going to give you superior brake pedal feel, less noise, superior pad wear, and lower the chances of cracking your discs.
Important Notes- PLEASE READ! First, make sure you are on a closed course to perform a proper bed-in. Do NOT perform the procedure on public roads. You need a stretch of asphalt with long straights, good visibility, and no potential obstructions. Make sure you are in a position to safely and repeatedly attain the necessary speeds to perform the bed-in procedure. A controlled racetrack is the best place to perform this procedure. AP Racing and Competition Motorsport in no way suggest or condone speeding on public roads or breaking the law in your car, nor do we take responsibility for any damage or injury that occurs as a result of using our product or these procedures. You are performing the bed-in procedure at your own risk.
During these procedures, it’s critical that you never come to a complete stop with your foot on the brake pedal. If you have brake ducts on your car, you may want to block them off to allow your brake system to heat up easily. The procedure outlined below is a generic procedure for most types of mild race pad. Please check your pad manufacturer’s recommended bed-in procedure.
Accelerate to approximately 60mph and then decelerate down to 5 mph. If your car has ABS, you should try to hold the brakes at a point just before ABS intervention.
Once the car slows to 5mph, immediately accelerate back up to about 60mph, and brake again to roughly 5mph.
Repeat this series of stopping and accelerating 8 to 10 times. Again, do not come to a complete stop with your foot on the brake pedal.
Cool the brake system down by cruising at 45mph+ for 5 to 10 minutes.
Visually inspect your discs. They should be a blue/grey color (instead of shiny silver), and have an even layer of pad material across and around the entire rotor face.
If the AP Racing rotors don’t have a layer of pad material on them, perform another series of stops in the manner outlined above.